The Influence of 3D Printing Parameters on Elastic and Mechanical Characteristics of Polylactide

2019 ◽  
Vol 957 ◽  
pp. 483-492 ◽  
Author(s):  
Florin Baciu ◽  
Daniel Vlăsceanu ◽  
Anton Hadăr
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Mechanical Characteristics ◽  
Testing Machine ◽  
Young Modulus ◽  
Tensile Loading ◽  
Material Behavior ◽  
Experimental Investigations ◽  
Universal Testing ◽  
Printing Parameters

The purpose of this paper is to evaluate the influence of 3D printing parameters (i.e. print speed, infill density, infill patterns) on the elastic and mechanical properties (i.e. Young modulus, yield limit, ultimate tensile strength). These properties have been determined experimentally on different specimens subjected to tensile loading using a universal testing machine INSTRON 8872. For these experimental investigations, the test specimens were manufactured in accordance to ASTM standards, modifying the following printing parameters: print speed, infill density, infill patterns. The influence of printing parameters on elastic and mechanical properties is necessary for a better understanding of the material behavior necessary in modelling and design of some type of structures manufactured using 3D printing method.

scholarly journals Comparisons between some composites reinforced with corn leaves and different matrices

2021 ◽  
Vol 343 ◽  
pp. 01002
Author(s):  
Alexandru Ioan Rădoi ◽  
Cosmin Mihai Miriţoiu ◽  
Claudiu Nicolicescu
Keyword(s):  
Tensile Test ◽  
Mechanical Characteristics ◽  
Breaking Strength ◽  
Testing Machine ◽  
Young Modulus ◽  
Rectangular Section ◽  
Polyester Resins ◽  
Elongation At Break ◽  
Universal Testing ◽  
The Matrix

In this paper we build some composite materials reinforced with corn leaves. In order to build the samples, we have firstly created some strips in this way: we put the corn leaves, continuously, on a sheet of paper where we apply a this layer of resin (we have used epoxy and polyester ones). We have waited for the resin polymerization 48 hours, recommended by the producer. We have put the corn leaves layers in the director of the tensile test (because we will test the samples to tensile). We have made 10 strips and we have glued them together by using the same synthetic resins (epoxy and polyester). In the end we have obtained some composites reinforced with strips from corn leaves and paper sheet, and the matrix is made from epoxy and polyester resins. From the obtained plate, we have cut some samples in order to study their statically mechanical characteristics by tensile test. The samples were tested on an universal testing machine INSTRON 1000 HDX which is assisted by a software called Bluehill. The samples have a rectangular section We have determined: the elongation at break, the breaking strength and the Young modulus. We have also studied the samples breaking area..

scholarly journals Mimicking the Mechanical Properties of Aortic Tissue with Pattern-Embedded 3D Printing for a Realistic Phantom

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5042
Author(s):  
Jaeyoung Kwon ◽  
Junhyeok Ock ◽  
Namkug Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
3D Printing ◽  
Mechanical Characteristics ◽  
Aortic Wall ◽  
Tensile Tests ◽  
Human Aorta ◽  
Aortic Tissue ◽  
Medical Field ◽  
Base Materials

3D printing technology has been extensively applied in the medical field, but the ability to replicate tissues that experience significant loads and undergo substantial deformation, such as the aorta, remains elusive. Therefore, this study proposed a method to imitate the mechanical characteristics of the aortic wall by 3D printing embedded patterns and combining two materials with different physical properties. First, we determined the mechanical properties of the selected base materials (Agilus and Dragonskin 30) and pattern materials (VeroCyan and TPU 95A) and performed tensile testing. Three patterns were designed and embedded in printed Agilus–VeroCyan and Dragonskin 30–TPU 95A specimens. Tensile tests were then performed on the printed specimens, and the stress-strain curves were evaluated. The samples with one of the two tested orthotropic patterns exceeded the tensile strength and strain properties of a human aorta. Specifically, a tensile strength of 2.15 ± 0.15 MPa and strain at breaking of 3.18 ± 0.05 mm/mm were measured in the study; the human aorta is considered to have tensile strength and strain at breaking of 2.0–3.0 MPa and 2.0–2.3 mm/mm, respectively. These findings indicate the potential for developing more representative aortic phantoms based on the approach in this study.

scholarly journals Mechanical Properties of the Composite Material consisting of β-TCP and Alginate-Di-Aldehyde-Gelatin Hydrogel and Its Degradation Behavior

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1303
Author(s):  
Michael Seidenstuecker ◽  
Thomas Schmeichel ◽  
Lucas Ritschl ◽  
Johannes Vinke ◽  
Pia Schilling ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Protein Concentration ◽  
Failure Load ◽  
Testing Machine ◽  
Experimental Period ◽  
Flow Chamber ◽  
Degradation Behavior ◽  
Gelatin Hydrogel ◽  
Universal Testing

This work aimed to determine the influence of two hydrogels (alginate, alginate-di-aldehyde (ADA)/gelatin) on the mechanical strength of microporous ceramics, which have been loaded with these hydrogels. For this purpose, the compressive strength was determined using a Zwick Z005 universal testing machine. In addition, the degradation behavior according to ISO EN 10993-14 in TRIS buffer pH 5.0 and pH 7.4 over 60 days was determined, and its effects on the compressive strength were investigated. The loading was carried out by means of a flow-chamber. The weight of the samples (manufacturer: Robert Mathys Foundation (RMS) and Curasan) in TRIS solutions pH 5 and pH 7 increased within 4 h (mean 48 ± 32 mg) and then remained constant over the experimental period of 60 days. The determination surface roughness showed a decrease in the value for the ceramics incubated in TRIS compared to the untreated ceramics. In addition, an increase in protein concentration in solution was determined for ADA gelatin-loaded ceramics. The macroporous Curasan ceramic exhibited a maximum failure load of 29 ± 9.0 N, whereas the value for the microporous RMS ceramic was 931 ± 223 N. Filling the RMS ceramic with ADA gelatin increased the maximum failure load to 1114 ± 300 N. The Curasan ceramics were too fragile for loading. The maximum failure load decreased for the RMS ceramics to 686.55 ± 170 N by incubation in TRIS pH 7.4 and 651 ± 287 N at pH 5.0.

scholarly journals EFFECT OF STORAGE DURATION ON MECHANICAL PROPERTIES OF BELLO EGGPLANT FRUIT UNDER QUASI COMPRESSION LOADING

2019 ◽  
Vol 7 (5) ◽  
pp. 311-320
Author(s):  
Umurhurhu Benjamin ◽  
Uguru Hilary
Keyword(s):  
Mechanical Properties ◽  
Strong Dependence ◽  
Testing Machine ◽  
Storage Period ◽  
Maturity Stage ◽  
Rupture Force ◽  
Storage Duration ◽  
Compression Loading ◽  
Universal Testing ◽  
Rupture Energy

The mechanical properties of eggplant fruit (cv. Bello) harvested at physiological maturity stage were evaluated in three storage periods (3d, 6d and 9d). These mechanical parameters (rupture force, rupture energy and deformation at rupture point) were measured under quasi compression loading, using the Universal Testing Machine (Testometric model). The fruit’s toughness and rupture power were calculated from the data obtained from the rupture energy and deformation at rupture point. Results obtained showed that mechanical properties of the Bello eggplant fruit exhibited strong dependence on the storage period. The results showed that as the Bello fruit stored longer, its rupture force and rupture energy decreased from 812 N to 411 N, and 5.58 Nm to 3.11 Nm respectively. While the rupture power decreased from 1.095 W to 0.353 W. On the contrary, the toughness and deformation at rupture increased from 0.270 mJ/mm3 to 0.403 mJ/mm3, and 16.99 mm to 25.22mm respectively during the 9 days storage period. The knowledge of the mechanical properties of fruits is important for their harvest and post-harvest operations, therefore, information obtained from this study will be useful in the design and development of machines for the mechanization of eggplant production.

Test of Physical Mechanical Properties of Gingko，Hickory Nut and their Stalks

2012 ◽  
Vol 479-481 ◽  
pp. 1145-1150
Author(s):  
Xiao Feng Xu ◽  
Wen Bin Yao ◽  
Jiu Hua Xu ◽  
Wei Zhang
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Testing Machine ◽  
Physical Characteristics ◽  
Harvest Time ◽  
Cutting Resistance ◽  
Moisture Contents ◽  
Universal Testing ◽  
The Impact ◽  
Physical Mechanics

In order to get the physical mechanics of gingko，hickory nut and their stalks, microprocessor controlled electronic universal testing machine (WDW-5E) was used to study the basic physical characteristics，pulling resistance and cutting resistance of their stalk in different harvest time and moisture contents. The impact of physical mechanics of cones and stalks on the picking process were analyzed and some concrete suggestions were put forward in the paper. This experimental study provides an important theory basis on designing and manufacturing different cones picking machine.

Performance Improvement Of Shrink-Fitted Assemblies by Surface Strengthening

1992 ◽  
Vol 206 (3) ◽  
pp. 207-213 ◽  
Author(s):  
B Ramamoorthy ◽  
V Radhakrishnan
Keyword(s):  
Performance Improvement ◽  
Testing Machine ◽  
Experimental Investigations ◽  
Ball Burnishing ◽  
Surface Strength ◽  
Interference Fit ◽  
Surface Strengthening ◽  
Compressive Stresses ◽  
Universal Testing

Interference fits are widely used in engineering applications. Many methods have been tried out to improve the strength of interference fits by improving the quality of the mating surfaces. An experimental investigation was carried out to study the strength of the assemblies after ball burnishing the shafts, which improves the surface finish and also imparts the surface strength by way of improving the hardness and residual compressive stresses. The assemblies were soaked for different duration times at elevated temperature and then the axial load-bearing tests were carried out in a Universal testing machine. The surface strengthening of shafts by burnishing and ageing of assemblies at high temperature resulted in considerable improvement of strength of the interference fit assemblies. This paper discusses the experimental investigations in detail and analyses the strength obtained from them.

scholarly journals Biogenic Composite Filaments Based on Polylactide and Diatomaceous Earth for 3D Printing

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4632
Author(s):  
Marta Dobrosielska ◽  
Robert Przekop ◽  
Bogna Sztorch ◽  
Dariusz Brząkalski ◽  
Izabela Zgłobicka ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Mechanical Characteristics ◽  
Filler Particle ◽  
Fused Deposition Modelling ◽  
Water Contact ◽  
Rheological Analysis ◽  
Fused Deposition ◽  
Filler Particle Size ◽  
Composite Properties

New composites containing a natural filler made of diatom shells (frustules), permitting the modification of polylactide matrix, were produced by Fused Deposition Modelling (3D printing) and were thoroughly examined. Two mesh fractions of the filler were used, one of <40 µm and the other of 40−63 µm, in order to check the effect of the filler particle size on the composite properties. The composites obtained contained diatom shells in the concentrations from 0% to 5% wt. (0−27.5% vol.) and were subjected to rheological analysis. The composites obtained as filaments of 1.75 mm in diameter were used for 3D printing. The printed samples were characterized as to hydrophilic–hydrophobic, thermal and mechanical properties. The functional parameters of the printed objects, e.g., mechanical characteristics, stability on contact with water and water contact angle, were measured. The results revealed differences in the processing behavior of the samples as well as the effect of secondary granulation of the filler on the parameters of the printing and mechanical properties of the composites.

About the Static Mechanical Properties of Epoxy/Hemp Composites

2020 ◽  
Vol 896 ◽  
pp. 321-326
Author(s):  
Cosmin Mihai Miriţoiu ◽  
Nicolae Craciunoiu ◽  
Alexandru Bolcu ◽  
Ionuţ Daniel Geonea ◽  
Ionica Valeriu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Standard Deviation ◽  
Tensile Test ◽  
Yield Stress ◽  
Mechanical Characteristics ◽  
Breaking Strength ◽  
Young Modulus ◽  
Breaking Elongation ◽  
Static Mechanical ◽  
Static Mechanical Properties

In this paper, static mechanical characteristics for some epoxy/hemp composites are studied. By using the tensile test, the static mechanical characteristics are determined, such as: breaking strength, yield stress, Young modulus and breaking elongation. There is also determined the standard deviation. Then, by using some known theories, there is validated the static Young modulus.

Modeling Method of Assembled Structure Coupling the Characteristics of the Joints

2012 ◽  
Vol 468-471 ◽  
pp. 2141-2148
Author(s):  
Tie Neng Guo ◽  
Xue Li Yu ◽  
Fu Ping Li ◽  
Li Gang Cai ◽  
Ya Hui Cui
Keyword(s):  
Mechanical Properties ◽  
Mechanical Characteristics ◽  
Element Model ◽  
Experimental Investigations ◽  
Beam Elements ◽  
Joint Characteristics ◽  
Proposed Model ◽  
Mechanics Analysis ◽  
Stiffness And Damping ◽  
The Finite Element Model

Mechanical properties of the joints have impacted on the whole mechanical characteristics. Coupling the joint characteristics in the modeling of the machine tool is an important problem in machine mechanics analysis. In order to solve the joint modellings in the assembled structure, this paper presents a new method to creat beam elements between two symmetrical nodes on the contact surface of the joint. The stiffness and damping matrices of the elements are valuated according to the characteristics of the joint. To validate the accuracy of the proposed method, the modeling of an assembled structure with and without the joints is obtained and some corresponding experimental investigations are implemented. The error between the simulated and experimental results of the finite element model is less than 8.8%, while the error of the contact model often used in the existing literatures is one times bigger than the proposed model.

Studies on Friction and Mechanical Properties of High Density Polypropylene (HDPP) Filled with Modified Talc

2012 ◽  
Vol 624 ◽  
pp. 279-282
Author(s):  
Feng Zhan ◽  
Nan Chun Chen
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Lamellar Structure ◽  
Testing Machine ◽  
High Density ◽  
Impact Testing ◽  
Wear Testing ◽  
Frictional Surface ◽  
Universal Testing ◽  
Scanning Electron

Talc was modified by aluminate coupling agent (ACA) before filling it into high density polypropylene (HDPP) to prepare talc/HDPP composites. Scanning electron microscopy (SEM), wear testing machine, electronic universal testing machine, and impact testing machine were used to analyze the surface modification and the effects of modified talc on friction and mechanical properties of modified talc/HDPP composites. The results indicate that after modified the lamellar structure of talc particles are open and the dispersion of particles are improved, and the edges and corners of surface become softer. Friction properties indicate that when the talc content is 8 wt%, both µ and K are at a lower value, which show that have better wear resistance. The frictional surface is relatively smooth and no furrow trace has found. Mechanical properties show that with talc content increasing, tensile strength and flexural strength of composites increase.

Sign in / Sign up

Export Citation Format

Share Document