The Effects of Chloride, Nitrate, and Nitrite on the Localized Corrosion of Carbon Steel in Simulated Concrete Pore Solutions

CORROSION ◽  
10.5006/3667 ◽  
2021 ◽  
Author(s):  
Chenxi Liu ◽  
Narasi Sridhar
Keyword(s):  
Carbon Steel ◽  
Electrochemical Impedance ◽  
Open Circuit ◽  
Localized Corrosion ◽  
Reinforcing Bars ◽  
Electrochemical Parameters ◽  
Cyclic Potentiodynamic Polarization ◽  
Burman Design ◽  
The Difference ◽  
Nitrate And Nitrite

Localized corrosion is a precursor to the deterioration of carbon steel reinforcing bars in concrete. The localized corrosion of carbon steel in simulated concrete pore solutions was investigated by cyclic potentiodynamic polarization (CPP) technique. A four-factor, two-level, full factorial design and a five-factor, two-level, Plackett-Burman design were used to study the effects of OH-, Cl-, NO3-, NO2-, with Na+ and Ca2+ cations on the localized corrosion of carbon steel. The results show that the occurrence of localized corrosion can be evaluated by the type of CPP curves (negative, mixed or positive hysteresis) and the difference between the open circuit and repassivation potentials (OCP- Erp). The lowest (OCP- Erp), indicating a low risk of pitting corrosion, could be obtained with high OH-, high NO2-, and low Cl-, whereas the effect of NO3- was not significant. The corrosion activities near the OCP were measured using Linear Polarization Resistance (LPR) and Electrochemical Impedance Spectroscopy (EIS) methods. They indicated that NO2- and Cl- were the main factors influencing the corrosion rate. The cationic species did not have a significant influence on the electrochemical parameters.

scholarly journals Effect of Nitrogen on the Corrosion Behavior of Austenitic Stainless Steel in Chloride Solutions

2015 ◽  
Vol 9 (11) ◽  
pp. 119 ◽  
Author(s):  
W. A. Ghanem ◽  
W. A. Hussein ◽  
S. N. Saeed ◽  
S. M. Bader ◽  
R. M. Abou Shahba
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Austenitic Stainless Steel ◽  
Electrochemical Impedance ◽  
Open Circuit ◽  
Localized Corrosion ◽  
Partial Replacement ◽  
General Corrosion ◽  
Heat Treated ◽  
The Difference

The effect of partial replacement of nickel with nitrogen on the corrosion resistance of newly designed austenitic stainless steel samples without and with heat treated was investigated in 3.5wt% and 5wt% NaCl solution using open-circuit, potentiodynamic, cyclic anodic polarization and electrochemical impedance spectroscopy techniques. The results showed that, passivation in sample 1 where the highest addition of nickel and low addition of nitrogen is different from that for sample 4 where the nitrogen is greatest and the nickel is reduced almost to the third comparing sample 1. The difference in responses of heat treated samples to localized and general corrosion could be attributed to the difference in their phase compositions. The appearance of ferrite phase for samples (2, 4, 5 and 6) after heat treatment resulted in lowering the general and localized corrosion resistance than as forged samples in contrast with samples 1 and 3, where they still pure austenite. The obtained results are confirmed by surface examination.

An Inhibitive Effect of Aeration on the Pitting Corrosion of Steels in Ethanolic Environments

CORROSION ◽  
10.5006/4000 ◽  
2021 ◽  
Author(s):  
Ali Ashrafriahi ◽  
Anatolie Carcea ◽  
Roger Newman
Keyword(s):  
Carbon Steel ◽  
Pitting Corrosion ◽  
Surface Film ◽  
Steel Corrosion ◽  
Open Circuit ◽  
Localized Corrosion ◽  
Potential Measurement ◽  
Pitting Corrosion Resistance ◽  
Cyclic Potentiodynamic Polarization ◽  
Passivation Potential

This work is aimed at improving the understanding of the localized corrosion of carbon steel in ethanolic solutions. The role of ethanol dehydration, chloride, and oxygen level in the pitting behaviour of carbon steel in ethanolic environments in the presence of supporting electrolytes was investigated. Open Circuit Potential measurement, Cyclic Potentiodynamic Polarization and Potentiostatic testing were conducted on specimens exposed to ethanolic environments prepared from pure dehydrated ethanol to study the pitting behaviour of carbon steel. Corrosion and passivation potentials significantly reduce due to the change in the cathodic reaction and the decrease in passivation kinetics under de-aerated conditions. SEM and EDX examination indicated that no pitting corrosion is observed without chlorides, and chloride significantly destabilizes the surface film resulting in decreases of both corrosion potential and passivation potential. A decrease in the dissolved oxygen in the solution reduces but does not eliminate the pitting susceptibility. Iron oxide is identified as the significant corrosion product at different water and oxygen content. Therefore, ethanol aeration can be a proper method to increase pitting corrosion resistance in ethanolic solutions.

scholarly journals From Waste to Valuable Resource: Lignin as a Sustainable Anti-Corrosion Coating

Coatings ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 454 ◽  
Author(s):  
Arman Dastpak ◽  
Kirsi Yliniemi ◽  
Mariana de Oliveira Monteiro ◽  
Sarah Höhn ◽  
Sannakaisa Virtanen ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Open Circuit Potential ◽  
Electrochemical Impedance ◽  
Steel Corrosion ◽  
Linear Sweep Voltammetry ◽  
Corrosion Current ◽  
Polymer Coatings ◽  
Open Circuit ◽  
Linear Sweep ◽  
Cyclic Potentiodynamic Polarization

In this study, a waste of biorefinery—lignin—is investigated as an anticorrosion coating on stainless steel. Corrosion behavior of two lignin types (hardwood beech and softwood spruce) was studied by electrochemical measurements (linear sweep voltammetry, open circuit potential, potentiostatic polarization, cyclic potentiodynamic polarization, and electrochemical impedance measurements) during exposure to simulated body fluid (SBF) or phosphate buffer (PBS). Results from linear sweep voltammetry of lignin-coated samples, in particular, demonstrated a reduction in corrosion current density between 1 and 3 orders of magnitude cf. blank stainless steel. Furthermore, results from cross cut adhesion tests on lignin-coated samples demonstrated that the best possible adhesion (grade 0) of ISO 2409 standard was achieved for the investigated novel coatings. Such findings suggest that lignin materials could transform the field of organic coatings towards more sustainable alternatives by replacing non-renewable polymer coatings.

Nano-Thick Amorphous Oxide Layer Produced by Plasma on Type 316L Stainless Steel for Improved Corrosion Resistance Under Plastic Deformation

CORROSION ◽  
10.5006/2674 ◽  
2018 ◽  
Vol 74 (9) ◽  
pp. 1011-1022 ◽  
Author(s):  
Megan Mahrokh Dorri ◽  
Stéphane Turgeon ◽  
Maxime Cloutier ◽  
Pascale Chevallier ◽  
Diego Mantovani
Keyword(s):  
Plastic Deformation ◽  
Stainless Steel ◽  
Oxide Layer ◽  
Electrochemical Impedance ◽  
Open Circuit ◽  
Localized Corrosion ◽  
Native Oxide ◽  
Native Oxide Layer ◽  
Amorphous Oxide ◽  
Amorphous Oxide Layer

Localized corrosion constitutes a major concern in medical devices made of stainless steel. The conventional approach to circumvent such a problem is to convert the surface polycrystalline microstructure of the native oxide layer to an amorphous oxide layer, a few micrometers thick. This process cannot, however, be used for devices such as stents that undergo plastic deformation during their implantation, especially those used in vascular surgery for the treatment of cardiac, neurological, and peripheral vessels. This work explores the feasibility of producing a nano-thick plastic-deformation resistant amorphous oxide layer by plasma-based surface modifications. By varying the plasma process parameters, oxide layers with different features were produced and their properties were investigated before and after clinically-relevant plastic deformation. These properties and the related corrosion mechanisms were mainly evaluated using the electrochemical methods of open-circuit potential, cyclic potentiodynamic polarization, and electrochemical impedance spectroscopy. Results showed that, under optimal conditions, the resistance to corrosion and to the permeation of ions in a phosphate buffered saline, even after deformation, was significantly enhanced.

scholarly journals In-Situ Monitoring and Analysis of the Pitting Corrosion of Carbon Steel by Acoustic Emission

2019 ◽  
Vol 9 (4) ◽  
pp. 706 ◽  
Author(s):  
Junlei Tang ◽  
Junyang Li ◽  
Hu Wang ◽  
Yingying Wang ◽  
Geng Chen
Keyword(s):  
Acoustic Emission ◽  
Carbon Steel ◽  
Pitting Corrosion ◽  
Optical Microscope ◽  
Open Circuit ◽  
In Situ Monitoring ◽  
Localized Corrosion ◽  
Uniform Corrosion ◽  
Corrosion Morphology

The acoustic emission (AE) technique was applied to monitor the pitting corrosion of carbon steel in NaHCO3 + NaCl solutions. The open circuit potential (OCP) measurement and corrosion morphology in-situ capturing using an optical microscope were conducted during AE monitoring. The corrosion micromorphology was characterized with a scanning electron microscope (SEM). The propagation behavior and AE features of natural pitting on carbon steel were investigated. After completion of the signal processing, including pre-treatment, shape preserving interpolation, and denoising, for raw AE waveforms, three types of AE signals were classified in the correlation diagrams of the new waveform parameters. Finally, a 2D pattern recognition method was established to calculate the similarity of different continuous AE graphics, which is quite effective to distinguish the localized corrosion from uniform corrosion.

scholarly journals Corrosion of Carbon Steel in Artificial Geothermal Brine: Influence of Carbon Dioxide at 70 °C and 150 °C

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3801 ◽  
Author(s):  
Gabriela Aristia ◽  
Le Quynh Hoa ◽  
Ralph Bäßler
Keyword(s):  
Carbon Dioxide ◽  
Carbon Steel ◽  
Temperature Effect ◽  
Electrochemical Impedance ◽  
Corrosion Products ◽  
Localized Corrosion ◽  
Corrosion Mechanism ◽  
Sem Images ◽  
Geothermal Brine ◽  
Corrosive Effect

This study focuses on the corrosion mechanism of carbon steel exposed to an artificial geothermal brine influenced by carbon dioxide (CO2) gas. The tested brine simulates a geothermal source in Sibayak, Indonesia, containing 1500 mg/L of Cl−, 20 mg/L of SO42−, and 15 mg/L of HCO3− with pH 4. To reveal the temperature effect on the corrosion behavior of carbon steel, exposure and electrochemical tests were carried out at 70 °C and 150 °C. Surface analysis of corroded specimens showed localized corrosion at both temperatures, despite the formation of corrosion products on the surface. After 7 days at 150 °C, SEM images showed the formation of an adherent, dense, and crystalline FeCO3 layer. Whereas at 70 °C, the corrosion products consisted of chukanovite (Fe2(OH)2CO3) and siderite (FeCO3), which are less dense and less protective than that at 150 °C. Control experiments under Ar-environment were used to investigate the corrosive effect of CO2. Free corrosion potential (Ecorr) and electrochemical impedance spectroscopy (EIS) confirm that at both temperatures, the corrosive effect of CO2 was more significant compared to that measured in the Ar-containing solution. In terms of temperature effect, carbon steel remained active at 70 °C, while at 150 °C, it became passive due to the FeCO3 formation. These results suggest that carbon steel is more susceptible to corrosion at the near ground surface of a geothermal well, whereas at a deeper well with a higher temperature, there is a possible risk of scaling (FeCO3 layer). A longer exposure test at 150 °C with a stagnant solution for 28 days, however, showed the unstable FeCO3 layer and therefore a deeper localized corrosion compared to that of seven-day exposed specimens.

Conducting polyaniline/multi-wall carbon nanotubes composite paints on low carbon steel for corrosion protection: electrochemical investigations

2013 ◽  
Vol 67 (8) ◽  
Author(s):  
Pravin Deshpande ◽  
Sanket Vathare ◽  
Shashikant Vagge ◽  
Elena Tomšík ◽  
Jaroslav Stejskal
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Steel ◽  
Corrosion Protection ◽  
Open Circuit Potential ◽  
Electrochemical Impedance ◽  
Low Carbon Steel ◽  
Open Circuit ◽  
Low Carbon ◽  
Multi Wall Carbon Nanotubes ◽  
Poly Aniline

AbstractThe coaxial coating of multi-wall carbon nanotubes (MWCNT) with poly(aniline) (PANI) was synthesised and a paint was prepared containing conducting PANI-MWCNT composite. The corrosion protection performance was assessed by open circuit potential measurements, potentiodynamic polarisation, and electrochemical impedance spectroscopy. The corrosion rate of low-carbon steel coated with 1.5 mass % of PANI-MWCNT-based paint in 3.5 mass % sodium chloride solution was found to be 0.037 mm y−1, about 5.2 times lower than that of unpainted low-carbon steel and 3.6 times lower than that of epoxy painted steel.

Effect of Different Dopants in Films TEOS/MPTS Used to Protect the Carbon Steel

2014 ◽  
Vol 805 ◽  
pp. 167-171 ◽  
Author(s):  
F.S. Silva ◽  
P.H. Suegama ◽  
W.P. Silva ◽  
A.W. Rinaldi ◽  
N.L.C. Domingues ◽  
...  
Keyword(s):  
Carbon Steel ◽  
Open Circuit Potential ◽  
Hybrid Film ◽  
Electrochemical Impedance ◽  
Open Circuit ◽  
The Other ◽  
Nacl Solution ◽  
Hybrid Films ◽  
Impedance Measurements ◽  
Current Densities

Schiff bases m-toluene N-Salicylideneaniline (m-TOL), (B) m-nitro-N- Salicylideneaniline (m-NTR) and (C) m-methoxy-N-salicylideneaniline (m-MTX) and cerium ions were studied added to 3.5 wt.% NaCl solution and added to the hybrid film based tetraethoxysilane (TEOS) e 3-methacryloxypropyltrimethoxysilane (MPTS). The polarization measurements showed lower current densities for the steel in NaCl with m-MTX, indicating that the m-MTX may be acting as an inhibitor. The hybrid films were doped with the m-MTX, Ce (III) or Ce (IV). Electrochemical measurements of open circuit potential (EOC), polarization curves and electrochemical impedance spectroscopy (EIS), were used to evaluate the corrosion behavior of the hybrid films. According Electrochemical Impedance measurements, all hybrid films, provided protection to the carbon steel. The films doped with Ce (IV), provided greater protection than the other, which indicates that this is the most suitable dopant for use in films.

Environmental Effects on Localized Corrosion of a High-Level Nuclear Waste Container Material

1990 ◽  
Vol 212 ◽  
Author(s):  
N. Sridhar ◽  
G. Cragnolino ◽  
W. Machowski
Keyword(s):  
Localized Corrosion ◽  
A Value ◽  
Waste Container ◽  
Electrochemical Parameters ◽  
Cyclic Potentiodynamic Polarization ◽  
High Level Nuclear Waste ◽  
Full Factorial Experimental Design ◽  
High Level ◽  
Full Factorial ◽  
High Chloride

ABSTRACTThe effect of environmental variables on the localized corrosion behavior of alloy 825 is examined in this paper. Cyclic, potentiodynamic polarization tests based on a two-level, full factorial experimental design were conducted. An index incorporating both the visual and scanning electron microscope examinations of localized corrosion and the electrochemical parameters was used for the statistical analysis. The analysis showed that chloride is the single most important promoter of localized corrosion, while nitrate was the single most important inhibitor. Fluoride was a weak inhibitor, especially at low chloride levels. Sulfate was a weak promoter, especially at high chloride levels. Temperature did not have a significant effect within the chloride levels examined. Separate experiments indicated that silicon, added as metasilicate, did not have any significant effect on localized corrosion. The adverse effect of chloride was observed at concentrations as low as 100 ppm. Addition of H2O2 increased the corrosion potential of alloy 825 to a value above the repassivation potential observed in the 300 ppm chloride solution.

Evaluation of Ni0.5Zn0.5Fe2O4 nanoparticles as anti-corrosion pigment in organic coatings for carbon steel

2017 ◽  
Vol 64 (6) ◽  
pp. 644-653 ◽  
Author(s):  
A.U. Chaudhry ◽  
Vikas Mittal ◽  
M.I. Hashmi ◽  
Brajendra Mishra
Keyword(s):  
Carbon Steel ◽  
Electrochemical Impedance ◽  
Electrochemical Techniques ◽  
Open Circuit ◽  
Corrosion Layer ◽  
Organic Coatings ◽  
Metallic Oxide ◽  
Corrosion Properties ◽  
Content Type ◽  
Wide Range

Purpose Inorganic oxide addition can be synergistically beneficial in organic coatings if it can impart anti-corrosion properties and also act as an additive to enhance physical and/or chemical properties. The aim of this study was to evaluate the anti-corrosion benefits of nano nickel zinc ferrite (NZF) in the polymer film. Design/methodology/approach The time-dependent anti-corrosion ability of NZF (0.12-1.0 per cent w/w NZF/binder), applied on API 5L X-80 carbon steel, was characterized by electrochemical techniques such as open circuit potential, electrochemical impedance spectroscopy, linear polarization resistance and potentiodynamic. Characterization of corrosion layer was done by removing coatings after 216 h of immersion in 3.5 per cent w/v NaCl. Optical microscopy, field emission scanning electron microscopy and X-ray diffraction techniques were used to characterize the corroded surface. Findings Corrosion measurements confirm the electrochemical activity by metallic cations on the steel surface during corrosion process which results in improvement of anti-corrosion properties of steel. Moreover, surface techniques show compact corrosion layer coatings and presence of different metallic oxide phases for nanocomposite coatings. Originality/value The suggested protection mechanism was explained by the leaching and precipitation of metallic ion on the corroded surface which in turn slowed down the corrosion activity. Furthermore, improvement in barrier properties of rubber-based coatings was confirmed by the enhanced pore resistance. This work indicates that along with a wide range of applications of NZF, anti-corrosion properties can be taken as an addition.

Sign in / Sign up

Export Citation Format

Share Document