Strength comparative analysis of furniture joints made of various materials

2021 ◽  
Vol 113 ◽  
pp. 89-97
Author(s):  
Maciej Sydor ◽  
Agnieszka Kwapich ◽  
Piotr Pohl
Keyword(s):  
Comparative Analysis ◽  
Load Capacity ◽  
Bending Moment ◽  
Maximum Load ◽  
Lignocellulosic Materials ◽  
Sample Rotation ◽  
Hard Materials ◽  
Low Visibility ◽  
Strength And Stiffness ◽  
Joint Rigidity

The strength comparative analysis of furniture joints made of various materials. The influence of the load on the angular deformation of the furniture joint samples made of various materials was studied. The tests were carried out for six types of furniture materials: chipboard, MDF, hardwood plywood, glued pine wood, glued oak wood and HPL and for three types of fasteners with different ways of fixing in connected elements: shape-thread, expansion-expansion and expansion-thread way of anchoring in material of boards. The joint samples were loaded with a bending moment only (without inducing transverse loadings). The maximum load capacity and load capacity at the 3° (0.052 rad) sample rotation was measured and then the stiffness coefficients were calculated. Considerable differences were found between HPL and others lignocellulosic materials. Expansion fasteners offer incredibly low joint rigidity. This was observed for all tested furniture materials, from soft (chipboard) to very hard (HPL). Expansion connectors work better in soft lignocellulosic materials than in hard materials. The main advantage of expansion fasteners, in comparison to shape-thread fasteners, is its low visibility in the joint and the technological ease of assembly. On the other hand, thread-shaped connectors offer much greater strength and stiffness of joints.

scholarly journals Experimental and Simulation Investigation of Bending Moment Effect on Hollow Columns of Multi-layers of Hybrid Materials

2019 ◽  
Vol 12 (1) ◽  
pp. 44-55
Author(s):  
Ayad A. Ramadhan
Keyword(s):  
Hybrid Materials ◽  
Volume Fraction ◽  
Load Capacity ◽  
Testing Machine ◽  
Bending Moment ◽  
Maximum Load ◽  
Experimental Procedure ◽  
Bending Load ◽  
Alumina Composite ◽  
Moment Effect

This paper presented the effect of bending on multi-layer of hollow columns of Hybrid materials (Carbon-Glass /epoxy-Alumina) composite this effect occurred and volume fraction of fibers. An experimental procedure was developed to study the performance of these effects under bending load using a hydraulic bending device type (MATEST. SRL) testing machine. This study has three forms through the selection of columns hollows width to thickness (a/b) (0.5, 1 and 2) with three types of layers of samples (2,4 and8) layers. The ultimate load of failure for each Hybrid/epoxy-Al2O3 had been determined and specified the optimum volume fraction (Vf) due to the effect of mixing 50% and 60% were low in the case for compared 55% volume fraction. To simulate this problem the researcher used Explicit Mesh for AUTODYN under ANSYS-15 software, it was found that maximum bending load for Hybrid/ Epoxy-Al2O3 Specimens, the maximum load of specimens increased with increasing number of layers from 2L to 8L. The results also identified that the maximum load capacity by 55% volume fraction and a/b=0.5 of all composite specimens was highest from the others types of (50% and 60%) volume fractions and (a/b=1 and a/b=2) .Also, the Increasing ratio of stress capacity for specimens have 4 to 2 layers (4/2)  and 8 to 4  (8/4) for experimental results have maximum value with increasing by 48.19%  and 46.84% at (Sp.4#8/Sp.2#4) and (Sp.8#6/Sp.4#6) respectively.

scholarly journals A New Method to Calculate Water Film Stiffness and Damping for Water Lubricated Bearing with Multiple Axial Grooves

2020 ◽  
Vol 33 (1) ◽  
Author(s):  
Guojun Ren
Keyword(s):  
Analytical Procedure ◽  
Load Capacity ◽  
Water Film ◽  
New Method ◽  
Hard Materials ◽  
Stiffness And Damping ◽  
Film Stiffness ◽  
Hydro Turbines

Abstract Water lubricated guide bearings for hydro turbines and pumps are conventionally designed with multiple axial grooves to provide effectively cooling and flushing away abrasives. Due to the variety of groove configuration in terms of number and size, a predication of their performance is difficult. This paper deals with an analytical procedure to investigate groove effect on load capacity, stiffness and damping for this type of bearing where it is considered as an assembly of many inclined slide bearings. The result can be applied to bearings made of hard materials combined with low bearing pressure.

scholarly journals Design and Analysis of an Aerostatic Pad Controlled by a Diaphragm Valve

Lubricants ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 47
Author(s):  
Federico Colombo ◽  
Luigi Lentini ◽  
Terenziano Raparelli ◽  
Andrea Trivella ◽  
Vladimir Viktorov
Keyword(s):  
Sensitivity Analysis ◽  
High Precision ◽  
Load Capacity ◽  
Design Procedure ◽  
Maximum Load ◽  
Air Gap ◽  
Diaphragm Valve ◽  
Compensation Methods ◽  
Aerostatic Bearings ◽  
Gap Height

Because of their distinctive characteristics, aerostatic bearings are particularly suitable for high-precision applications. However, because of the compressibility of the lubricant, this kind of bearing is characterized by low relative stiffness and poor damping. Compensation methods represent a valuable solution to these limitations. This paper presents a design procedure for passively compensated bearings controlled by diaphragm valves. Given a desired air gap height at which the system should work, the procedure makes it possible to maximize the stiffness of the bearing around this value. The designed bearings exhibit a quasi-static infinite stiffness for load variation ranging from 20% to almost 50% of the maximum load capacity of the bearing. Moreover, the influence of different parameters on the performance of the compensated pad is evaluated through a sensitivity analysis.

Dependency of Machine Efficiency on the Thermal Behavior of Induction Machines

Machines ◽  
2020 ◽  
Vol 8 (1) ◽  
pp. 9
Author(s):  
Svenja Kalt ◽  
Karl Ludwig Stolle ◽  
Philipp Neuhaus ◽  
Thomas Herrmann ◽  
Alexander Koch ◽  
...  
Keyword(s):  
Thermal Behavior ◽  
Electric Vehicles ◽  
Thermal Load ◽  
Load Capacity ◽  
Maximum Load ◽  
Induction Machines ◽  
Electric Machines ◽  
Model Parameters ◽  
Dynamic Operating ◽  
The Impact

The consideration of the thermal behavior of electric machines is becoming increasingly important in the machine design for electric vehicles due to the adaptation to more dynamic operating points compared to stationary applications. Whereas, the dependency of machine efficiency on thermal behavior is caused due to the impact of temperature on the resulting loss types. This leads to a shift of efficiency areas in the efficiency diagram of electric machines and has a significant impact on the maximum load capability and an impact on the cycle efficiency during operation, resulting in a reduction in the overall range of the electric vehicle. Therefore, this article aims at analyzing the thermal load limits of induction machines in regard to actual operation using measured driving data of battery electric vehicles. For this, a thermal model is implemented using MATLAB® and investigations to the sensitivity of model parameters as well as analysis of the continuous load capacity, thermal load and efficiency in driving cycles under changing boundary conditions are conducted.

An Accurate Solution of the Gas Lubricated, Flat Sector Thrust Bearing

1977 ◽  
Vol 99 (1) ◽  
pp. 82-88 ◽  
Author(s):  
I. Etsion ◽  
D. P. Fleming
Keyword(s):  
Film Thickness ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Thickness Distribution ◽  
Maximum Load ◽  
Accurate Solution ◽  
Operating Conditions ◽  
Thrust Bearings ◽  
Practical Design ◽  
Minimum Film Thickness

A flat sector shaped pad geometry for gas lubricated thrust bearings is analyzed considering both pitch and roll angles of the pad and the true film thickness distribution. Maximum load capacity is achieved when the pad is tilted so as to create a uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves. A comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

scholarly journals Influence of stirrup spacing on shear resistance and deformation of reinforced concrete beams

2018 ◽  
Vol 7 (1) ◽  
pp. 126
Author(s):  
Latha M S ◽  
Revanasiddappa M ◽  
Naveen Kumar B M
Keyword(s):  
Concrete Beam ◽  
Concrete Beams ◽  
Bending Moment ◽  
Maximum Load ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Cement Concrete ◽  
Simply Supported ◽  
Reinforced Cement ◽  
Flexural Reinforcement

An experimental investigation was carried out to study shear carrying capacity and ultimate flexural moment of reinforced cement concrete beam. Two series of simply supported beams were prepared by varying diameter and spacing of shear and flexural reinforcement. Beams of cross section 230 mm X 300 mm and length of 2000 mm. During testing, maximum load, first crack load, deflection of beams were recorded. Test results indicated that decreasing shear spacing and decreasing its diameter resulted in decrease in deflection of beam and increase in bending moment and shear force of beam.

Design of Multi-Recess Hydrostatic Journal Bearings for Minimum Total Power Loss

1974 ◽  
Vol 96 (1) ◽  
pp. 226-232 ◽  
Author(s):  
C. Cusano ◽  
T. F. Conry
Keyword(s):  
Rotational Speed ◽  
Power Loss ◽  
Load Capacity ◽  
Maximum Load ◽  
Journal Bearings ◽  
Design Criterion ◽  
Total Power ◽  
Eccentricity Ratio ◽  
Constant Ratio ◽  
Design Charts

The design problem is formulated for multi-recess hydrostatic journal bearings with a design criterion of minimum total power loss. The design is subject to the constraints of constant ratio of the recess area to the total bearing area and maximum load capacity for a given recess geometry. The L/D ratio, eccentricity ratio, ratio of recess area to total bearing area, and shaft rotational speed are considered as parameters. The analysis is based on the bearing model of Raimondi and Boyd [1]. This model is generally valid for low-to-moderate speeds and a ratio of recess area-to-total bearing area of approximately 0.5 or greater. Design charts are presented for bearings having a ratio of recess area-to-total bearing area of 0.6 and employing capillary and orifice restrictors, these being the most common types of compensating elements. A design example is given to illustrate the use of the design charts.

scholarly journals A Modular Cooperative Wall-Climbing Robot Based on Internal Soft Bone

Sensors ◽  
2021 ◽  
Vol 21 (22) ◽  
pp. 7538
Author(s):  
Wenkai Huang ◽  
Wei Hu ◽  
Tao Zou ◽  
Junlong Xiao ◽  
Puwei Lu ◽  
...  
Keyword(s):  
Modular Design ◽  
Simulation Analysis ◽  
Load Capacity ◽  
Maximum Load ◽  
Variable Load ◽  
Climbing Robot ◽  
Element Simulation ◽  
Variable Step ◽  
In Series ◽  
Step Distance

Most existing wall-climbing robots have a fixed range of load capacity and a step distance that is small and mostly immutable. It is therefore difficult for them to adapt to a discontinuous wall with particularly large gaps. Based on a modular design and inspired by leech peristalsis and internal soft-bone connection, a bionic crawling modular wall-climbing robot is proposed in this paper. The robot demonstrates the ability to handle variable load characteristics by carrying different numbers of modules. Multiple motion modules are coupled with the internal soft bone so that they work together, giving the robot variable-step-distance functionality. This paper establishes the robotic kinematics model, presents the finite element simulation analysis of the model, and introduces the design of the multi-module cooperative-motion method. Our experiments show that the advantage of variable step distance allows the robot not only to quickly climb and turn on walls, but also to cross discontinuous walls. The maximum climbing step distance of the robot can reach 3.6 times the length of the module and can span a discontinuous wall with a space of 150 mm; the load capacity increases with the number of modules in series. The maximum load that modules can carry is about 1.3 times the self-weight.

scholarly journals Preliminary Design Framework for the Power Gearbox in a Contra-Rotating Open Rotor

2020 ◽  
Author(s):  
Diana G. San Benito Pastor ◽  
Devaiah Nalianda ◽  
Vishal Sethi ◽  
Ron Midgley ◽  
Andrew Rolt ◽  
...  
Keyword(s):  
System Design ◽  
Load Capacity ◽  
Engine Performance ◽  
Maximum Load ◽  
Transmission System ◽  
Published Data ◽  
Planetary Gearbox ◽  
Open Rotor ◽  
Parametric Analyses ◽  
The Impact

Abstract This study introduces an innovative approach to sizing a differential planetary gearbox for a counter-rotating open rotor application. An updated methodology is proposed for the design of maximum load capacity gears based on the power transmitted, durability and space-envelope requirements of the application. The reported methodology has been validated by comparing the results to published data, demonstrating a maximum difference of 0.6% in geometry. Parametric analyses have also been performed to assess the impact of the design assumptions on gearbox dimensional trends. The proposed methodology enables the assessment of the impact of the preliminary transmission system design on engine performance and general arrangement. The characteristics of the gearset lead to an unequal torque split between output shafts (i.e. the propeller shafts). Given the design assumptions made, the study indicates that valid torque ratios would lie between 1.1 and 1.33. The impact of the torque ratio on the size of the gearbox has been analysed for equal rotational speeds and for different speeds between the output shafts. The study established that the transmission system design needs to be considered prior to selection of the torque ratio at engine design level.

Sign in / Sign up

Export Citation Format

Share Document