Promotion of the Hypocrellin Yield by a Co-Culture of Shiraia bambusicola (GDMCC 60438) with Arthrinium sp. AF-5 Fungus

Hypocrellin is a natural 3,10-xylene-4,9-anthracene derivative compound that originates from the stroma of Shiraia bambusicola (S. bambusicola) and Hypocrella bambusae with excellent photobiological activities. Submerged fermentation with the mycelia of S. bambusicola is generally regarded as an ideal technology for hypocrellin production. This study developed a co-cultivation strategy for an obvious promotion of the hypocrellin yield by incubating S. bambusicola (GDMCC 60438) with the endophyte fungus Arthrinium sp. AF-5 isolated from the bamboo tissue. The results indicated that the yield of hypocrellin A (HA) reached a 66.75 mg/g carbon source after an 84-h co-cultivation of the two strains, which was a four-time increase of that by the fermentation only with the S. bambusicola. The microscope observation found that the mycelia of the two strains were intertwined with each other to form the mycelium pellets during the co-cultivation. Moreover, the mycelium pellets of the co-culture showed a contracted and slightly damaged morphology. The addition of H2O2 in the fermentation media could further increase the HA production by 18.31%.

Fabrication of three-dimensional photonic crystals for near-infrared light by micro-manipulation technique under optical microscope observation

We developed a micro-manipulation technique performed under optical microscope observation, which enabled accurate fabrication of three-dimensional photonic crystals for near-infrared light. Thin GaAs plates having an in-plane pattern were picked up with a fine needle and were mechanically stacked one-by-one by using vertical posts as guides. In spite of the limited spatial resolution in the optical microscope images, the mechanical resolution of the micro-manipulator and the precisely fabricated vertical posts enabled a stacking error as small as 20 nm. Photoluminescence measurement of a nanocavity in the three-dimensional photonic crystals showed a cavity-mode peak in the near-infrared region.

Novel Approach for Fine Ilmenite Flotation Using Hydrophobized Glass Bubbles as the Buoyant Carrier

Ilmenite disseminated grain size is relatively fine, and it must be finely ground to fully separate ilmenite from gangue and then produce fine-grained minerals, which deteriorates flotation. A novel method using buoyant carriers to improve the recovery of fine ilmenite in froth flotation was introduced in this study. Hydrophobized glass bubbles (HGB) as carrier materials were obtained by an efficient, simple modification of ordinary glass bubbles. The carrier flotation of fine ilmenite in the presence of HGB was investigated by micro flotation tests, X-ray diffractometer analysis, Fourier transform infrared (FTIR), optical microscope observation, and the extended DLVO theory (XDLVO). Micro-flotation results showed that the recovery of fine ilmenite in presence of HGB was 37.7% higher than that when using NaOL alone at pH 6. FTIR analysis and optical microscope observation revealed that fine ilmenite particles can be closely attached on the HGB surface to increase apparent particle size considerably. The data calculated from the DLVO theory indicated that the acid–base interaction force determined the adsorption between two hydrophobic particles.

Tensile Creep Behavior of Single-Crystal High-Entropy Superalloy at Intermediate Temperature

In this study, we investigated the creep deformation mechanism of a single-crystal high-entropy superalloy (HESA) with the spherical γ′ precipitates at 760 °C. Before the creep tests, long-term aging tests at 760 °C without load were conducted, which showed Ostwald ripening of the secondary γ′ precipitates up to 50 h. The creep tests revealed that in the range of 500 and 600 MPa at 760 °C, the creep deformation mechanism of HESA was independent of applied stress in both the primary and secondary creep regions. The deformation mechanism of HESA was further investigated under the condition of 760 °C and 520 MPa by performing creep interrupted tests and microstructural analysis. Scanning electron microscope observation showed elongated γ′ precipitates along the applied stress axis near the ruptured surface. This could have been caused by the multi-slip around <100> preceded by the lattice rotation into <100> along the tensile axis, which was confirmed by the electron backscatter diffraction analysis. Transmission electron microscope observation of the creep interrupted and ruptured specimens showed bypass and climb motion of dislocations in the 2-h interrupted, shearing of the γ′ precipitates by the paired straight dislocations in the 50-h interrupted, and shearing of the γ′ precipitates by both the straight and the curved paired dislocations in the ruptured specimens, respectively. The secondary γ′ precipitates do not affect creep behavior as long as the deformation mechanism is a bypass and climb motion of dislocations.

Comparative assessment of pollen micromorphology of Salvia assurgens (Lamiaceae), an endemic sage from Mexico

The present study provides novel information about the pollen of Salvia assurgens. Pollen grains were collected and described based on their observed characters by light microscope and scanning electron microscopy. The species is distinguished from other Mexican salvias by having small pollen grains (14.2 × 18.2 µm), thin primary muri (0.2 µm thick), elongated primary lumina (1.03 µm long) and secondary lumina with relatively few perforations (9, range 5–14). Pollen characters are similar to those of the majority of American salvias. Regarding Mexican sages, there has been little palynological research, and only 23 species of 32 examined have been quantitatively studied. Standardization is needed in different aspects of palynological studies, especially in relation to measurement protocols and data analysis, as well as the increased use of scanning electron microscopy (SEM), since the majority of differences among species are provided by SEM microscope observation.