Electrical conductivity and gas permeability of ceramic coatings produced by the plasma spraying of ZrO2 powder

Refractories ◽  
1978 ◽  
Vol 19 (1-2) ◽  
pp. 48-51
Author(s):  
V. K. Gil'derman ◽  
V. I. Zemtsov ◽  
A. D. Neuimin ◽  
S. F. Pal'guev ◽  
D. S. Rutman ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Plasma Spraying ◽  
Gas Permeability ◽  
Ceramic Coatings ◽  
Zro2 Powder

Electron microscopy studies of plasma-sprayed materials

1983 ◽  
Vol 41 ◽  
pp. 70-71
Author(s):  
K.R. Subramanian ◽  
A.H. King ◽  
H. Herman
Keyword(s):  
Plasma Spraying ◽  
Substrate Surface ◽  
Flame Temperature ◽  
Ceramic Coatings ◽  
Metallic Substrates ◽  
Hot Plasma ◽  
Almost All ◽  
Plasma Sprayed ◽  
Hostile Environments ◽  
Plasma Spraying Process

Plasma spraying is a technique which is used to apply coatings to metallic substrates for a variety of purposes, including hardfacing, corrosion resistance and thermal barrier applications. Almost all of the applications of this somewhat esoteric fabrication technique involve materials in hostile environments and the integrity of the coatings is of paramount importance: the effects of process variables on such properties as adhesive strength, cohesive strength and hardness of the substrate/coating system, however, are poorly understood.Briefly, the plasma spraying process involves forming a hot plasma jet with a maximum flame temperature of approximately 20,000K and a gas velocity of about 40m/s. Into this jet the coating material is injected, in powder form, so it is heated and projected at the substrate surface. Relatively thick metallic or ceramic coatings may be speedily built up using this technique.

scholarly journals Enhancing Graphene Retention and Electrical Conductivity of Plasma-Sprayed Alumina/Graphene Nanoplatelets Coating by Powder Heat Treatment

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 643
Author(s):  
Xiaoyu Wu ◽  
Shufeng Xie ◽  
Kangwei Xu ◽  
Lei Huang ◽  
Daling Wei ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Electrical Conductivity ◽  
Structural Integrity ◽  
Ceramic Coatings ◽  
Treatment Temperature ◽  
Graphene Nanoplatelets ◽  
Structural Defects ◽  
Temperature Plasma ◽  
Heat Treated ◽  
Plasma Sprayed

Burning loss of graphene in the high-temperature plasma-spraying process is a critical issue, significantly limiting the remarkable performance improvement in graphene reinforced ceramic coatings. Here, we reported an effective approach to enhance the graphene retention, and thus improve the performance of plasma-sprayed alumina/graphene nanoplatelets (Al2O3/GNPs) coatings by heat treatment of agglomerated Al2O3/GNPs powders. The effect of powder heat treatment on the microstructure, GNPs retention, and electrical conductivity of Al2O3/GNPs coatings were systematically investigated. The results indicated that, with the increase in the powder heat treatment temperature, the plasma-sprayed Al2O3/GNPs coatings exhibited decreased porosity and improved adhesive strength. Thermogravimetric analysis and Raman spectra results indicated that increased GNPs retention from 12.9% to 28.4%, and further to 37.4%, as well as decreased structural defects, were obtained for the AG, AG850, and AG1280 coatings, respectively, which were fabricated by using AG powders without heat treatment, powders heat-treated at 850 °C, and powders heat-treated at 1280 °C. Moreover, the electrical conductivities of AG, AG850, and AG1280 coatings exhibited 3 orders, 4 orders, and 7 orders of magnitude higher than that of Al2O3 coating, respectively. Powder heat treatment is considered to increase the melting degree of agglomerated alumina particles, eventually leaving less thermal energy for GNPs to burn; thus, a high retention amount and structural integrity of GNPs and significantly enhanced electrical conductivity were achieved for the plasma-sprayed Al2O3/GNPs coatings.

scholarly journals Wear Behavior Analysis of Al2O3 Coatings Manufactured by APS and HVOF Spraying Processes Using Powder and Suspension Feedstocks

Coatings ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 879
Author(s):  
Monika Michalak ◽  
Paweł Sokołowski ◽  
Mirosław Szala ◽  
Mariusz Walczak ◽  
Leszek Łatka ◽  
...  
Keyword(s):  
Plasma Spraying ◽  
Wear Behavior ◽  
Ceramic Coatings ◽  
Suspension Plasma Spraying ◽  
Atmospheric Plasma ◽  
Hvof Spraying ◽  
The Coefficient Of Friction ◽  
Wear Mode ◽  
Α Al2o3 ◽  
Plasma Sprayed

Thermally sprayed ceramic coatings are applied for the protection of surfaces that are exposed mainly to wear, high temperatures, and corrosion. In recent years, great interest has been garnered by spray processes with submicrometric and nanometric feedstock materials, due to the refinement of the structure and improved coating properties. This paper compares the microstructure and tribological properties of alumina coatings sprayed using conventional atmospheric plasma spraying (APS), and various methods that use finely grained suspension feedstocks, namely, suspension plasma spraying (SPS) and suspension high-velocity oxy-fuel spraying (S-HVOF). Furthermore, the suspension plasma-sprayed Al2O3 coatings have been deposited with radial (SPS) and axial (A-SPS) feedstock injection. The results showed that all suspension-based coatings demonstrated much better wear resistance than the powder-sprayed ones. S-HVOF and axial suspension plasma spraying (A-SPS) allowed for the deposition of the most dense and homogeneous coatings. Dense-structured coatings with low porosity (4 vol.%) and good cohesion to the metallic substrate, containing a high content of α–Al2O3 phase (56 vol.%) and a very low wear rate (0.2 ± 0.04 mm3 × 10−6/(N∙m)), were produced with the S-HVOF method. The wear mechanism of ceramic coatings included the adhesive wear mode supported by the fatigue-induced material delamination. Moreover, the presence of wear debris and tribofilm was confirmed. Finally, the coefficient of friction for the coatings was in the range between 0.44 and 0.68, with the highest values being recorded for APS sprayed coatings.

Laser Sintering of Nano-Al2O3 Powders on Plasma Sprayed Ceramic Based Coatings

2007 ◽  
Author(s):  
Lida Shen ◽  
Yinhui Huang ◽  
Zongjun Tian ◽  
Guoran Hua
Keyword(s):  
Wear Resistance ◽  
Corrosion Resistance ◽  
Plasma Spraying ◽  
Bond Coat ◽  
Continuous Wave ◽  
Ceramic Coatings ◽  
Laser Sintering ◽  
Al2o3 Ceramic ◽  
Plasma Sprayed ◽  
Steel Substrates

This paper describes an investigation of nano-Al2O3 powders reinforced ceramic coatings, which has included NiCrAl and Al2O3+13%wt.TiO2 coats pre-produced by atmosphere plasma spraying, implemented by laser sintering. Commercial NiCrAl powders were plasma sprayed onto 45 Steel substrates to give a bond coat with thickness of ∼100μm. The 600μm thick Al2O3+13%wt.TiO2 based coating was also plasma sprayed on top of the NiCrAl bond coat. With 2.5kw continuous wave CO2 laser, nano-Al2O3 ceramic powders were laser sintered on the based Coatings. The micro structure and chemical composition of the modified Al2O3+13%wt.TiO2 coatings were analyzed by such detection devices as scanning electronic microscope (SEM) and x-ray diffraction (XRD). Microhardness, wear resistance and corrosion resistance of the modified coatings were also tested and compared with that of the unmodified. The results show that the crystal grain size of Al2O3 had no obvious growth. In addition, due to the nanostructured Al2O3 ceramic phases, the coatings exhibited higher microhardness, better wear resistance and corrosion resistance than those unmodified counterparts. The complex process of plasma spraying with laser sintering as a potential effective way of the application of ceramic nano materials was also simply discussed and summarized in the end.

The Gas Permeability of Plasma Sprayed Ceramic Coatings

1997 ◽  
Author(s):  
A.C. Fox ◽  
T.W. Clyne
Keyword(s):  
Gas Permeability ◽  
Test Procedure ◽  
Ceramic Coatings ◽  
Hydrogen Gas ◽  
Steady State Flow ◽  
Flow Rates ◽  
Specific Permeability ◽  
Measured Flow ◽  
Flow Through ◽  
Plasma Sprayed

Abstract A simple test procedure, based on steady state flow through a membrane, has been developed for measurement of the gas permeability of specimens over a range of temperature. The reliability of this equipment has been verified by testing solid disks containing single perforations and comparing the measured flow rates with those expected on the basis of laminar flow. Coatings of yttria-stabilised zirconia have been produced by plasma spraying in vacuum and in air. The specific permeability of these coatings has been measured at temperatures ranging up to 600°C, using hydrogen gas. It has been found that permeability is increased for coatings produced with longer stand-off distances and at higher pressures. Porosity levels have been measured using densitometry and microstructural features have been examined using SEM. A model has been developed for prediction of the permeability from such microstructural features, based on percolation theory. Agreement between predicted and measured permeabilities is good, although it is clear that more comprehensive data are needed in order to validate the model systematically.

Development & Characterization of Alumina Coating by Atmospheric Plasma Spraying

2018 ◽  
Vol 877 ◽  
pp. 104-109 ◽  
Author(s):  
Jobin Sebastian ◽  
Abyson Scaria ◽  
Don George Kurian
Keyword(s):  
Plasma Spraying ◽  
Elevated Temperatures ◽  
Steel Substrate ◽  
Oxide Coating ◽  
Ceramic Coatings ◽  
Substrate Material ◽  
Atmospheric Plasma ◽  
Flame Spraying ◽  
Alumina Coating ◽  
Spray Process

Ceramic coatings are applied on metals to prevent them from oxidation and corrosion at room as well as elevated temperatures. The service environment, mechanisms of protection, chemical and mechanical compatibility, application method, control of coating quality and ability of the coating to be repaired are the factors that need to be considered while selecting the required coating. The coatings based on oxide materials provides high degree of thermal insulation and protection against oxidation at high temperatures for the underlying substrate materials. These coatings are usually applied by the flame or plasma spraying methods. The surface cleanliness needs to be ensured before spraying. Abrasive blasting can be used to provide the required surface roughness for good adhesion between the substrate and the coating. A pre bond coat like Nickel Chromium can be applied on to the substrate material before spraying the oxide coating to avoid chances of poor adhesion between the oxide coating and the metallic substrate. Plasma spraying produces oxide coatings of greater density, higher hardness, and smooth surface finish than that of the flame spraying process Inert gas is often used for generation of plasma gas so as to avoid the oxidation of the substrate material. The work focuses to develop, characterize and optimize the parameters used in Al2O3 coating on transition stainless steel substrate material for minimizing the wear rate and maximizing the leak tightness using plasma spray process. The experiment is designed using Taguchi’s L9 orthogonal array. The parameters that are to be optimized are plasma voltage, spraying distance and the cooling jet pressure. The characterization techniques includes micro-hardness and porosity tests followed by Grey relational analysis of the results

Sign in / Sign up

Export Citation Format

Share Document