scholarly journals Thermodynamic analysis and isothermal bainitic transformation kinetics in lean medium-Mn steels

2020 ◽  
Vol 142 (5) ◽  
pp. 1709-1719 ◽  
Author(s):  
M. Morawiec ◽  
V. Ruiz-Jimenez ◽  
C. Garcia-Mateo ◽  
A. Grajcar
Keyword(s):  
Thermodynamic Analysis ◽  
Retained Austenite ◽  
Manganese Content ◽  
Isothermal Holding ◽  
Xrd Analysis ◽  
Bainitic Transformation ◽  
Transformation Kinetics ◽  
Bainite Transformation ◽  
Different Temperatures ◽  
Fresh Martensite

AbstractThe work presents the results of thermodynamic analysis of two medium manganese steels with different Mn contents. The steels containing 3.1 and 3.6% of manganese were subjected to theoretical thermodynamic calculations using MUCG83 software and dilatometric experiments. The steels were heat-treated in two different isothermal holding temperatures of 400 and 350 °C for 15 min. The bainite transformation kinetics at different temperatures for different manganese contents was investigated. In the steel including 3.1% Mn, a complete transformation was obtained. The results indicated a strong influence of the holding temperature on the kinetics of bainitic transformation. It was related to the driving force of this process. When the manganese content was increased by 0.5%, an incomplete bainite transformation occurred. The microstructure investigations after heat treatment were performed using light and scanning electron microscopy. The XRD analysis to determine retained austenite amount and its carbon enrichment was performed. The microstructure of 3MnNb steel consisted of bainite and retained austenite with filmlike and blocky morphologies. The steel with the higher Mn content contained also fresh martensite for both isothermal holding temperatures.

scholarly journals Influence of Prior Martensite on Bainite Transformation, Microstructures, and Mechanical Properties in Ultra-Fine Bainitic Steel

Materials ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 527 ◽  
Author(s):  
Hui Guo ◽  
Xianying Feng ◽  
Aimin Zhao ◽  
Qiang Li ◽  
Jun Ma
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Bainitic Ferrite ◽  
Growth Direction ◽  
Bainitic Transformation ◽  
Bainitic Steel ◽  
Bainite Transformation ◽  
Multiphase Microstructure ◽  
Microstructures And Mechanical Properties ◽  
The Impact

A multiphase microstructure comprising of different volume fractions of prior martensite and ultra-fine bainite (bainitic ferrite and retained austenite) was obtained by quenching to certain temperatures, followed by isothermal bainitic transformation. The effect of the prior martensite transformation on the bainitic transformation behavior, microstructures, and mechanical properties were discussed. The results showed that the prior martensite accelerated the subsequent low-temperature bainite transformation, and the incubation period and completion time of the bainite reaction were significantly shortened. This phenomenon was attributed to the enhanced nucleation ratio caused by the introduced strain in austenite, due to the formation of prior martensite and a carbon partitioning between the prior martensite and retained austenite. Moreover, the prior martensite could influence the crystal growth direction of bainite ferrite, refine bainitic ferrite plates, and reduce the dimension of blocky retained austenite, all of which were responsible for improving the mechanical properties of the ultra-fine bainitic steel. When the content of the prior martensite reached 15%, the investigated steels had the best performance, which were 1800 MPa and 21% for the tensile strength and elongation, respectively. Unfortunately, the increased content of the prior martensite could lead to a worsening of the impact toughness.

Effects of Thermomechanical Processing on Microstructure and Mechanical Properties Multiphase Steels Exhibiting a TRIP Effect

2007 ◽  
Vol 539-543 ◽  
pp. 4357-4362 ◽  
Author(s):  
Jiří Kliber ◽  
Gabriela Plestilova ◽  
Ondrej Zacek ◽  
Mahesh C. Somani
Keyword(s):  
Mechanical Properties ◽  
Hot Rolling ◽  
Trip Steel ◽  
Transformation Temperature ◽  
Retained Austenite ◽  
Thermomechanical Processing ◽  
Rolling Temperature ◽  
Bainitic Transformation ◽  
Bainite Transformation ◽  
Microstructure And Mechanical Properties

Effects of hot-rolling conditions on these steels are much less studied than their importance for practice would suggest. It should be emphasized that bainite transformation is the key reaction to enrich non-transformed austenite with carbon. This study was carried out in order to gain understanding of the effect of thermomechanical hot rolling on final microstructure and mechanical properties of C-Mn-Si TRIP steel. Fundamental of the transformation induced plasticity effect – TRIP is the stabilization of substantial amount of retained austenite down to the ambient temperature by thermomechanical processing and its subsequent transformation into strain induced martensite as a consequence of applied plastic deformation. The special prepared stepped specimens were rolled on laboratory tandem mill. The effects of finish rolling temperature, strain and isothermal bainite transformation temperature on mechanical properties of mentioned TRIP steel were evaluated (mechanical properties were examined with tension test). Major deformation, higher finishing rolling temperature and higher temperature of bainite hold result in drop in strength. Proportionately to the drop in strength, the ductility grows in the TRIP steel. Microstructures were examined with X-ray diffraction (retained austenite). Image analysis software was used to process SEM micrographs of structure (ferrite, bainite assessment). Plastometric testing was conducted on GLEEBLE 3800 thermo-mechanical simulator. First stage of experiment yielded stress-strain curves for various temperatures and strain rates. Gleeble 1500 was used for the remaining plastometric simulation. Specimens were reheated to austenitization temperature of 1100°C and soaked. Then they were cooled to the temperature of deformation and subsequently cooled at higher rate down to the bainitic transformation temperature (400 – 550 °C). Specimens were held at the bainitic transformation temperature and then air-cooled. Final microstructures were evaluated with respect to transformation diagrams and optical microscopy findings. Higher bainite volume fraction was found in the specimens cooled at higher cooling rate as compared with more slowly cooled specimens.

scholarly journals Continuous Cooling Transformation Behaviour and Bainite Transformation Kinetics of 23CrNi3Mo Carburised Steel

Metals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 48
Author(s):  
Wenjun Song ◽  
Min Lei ◽  
Mingpan Wan ◽  
Chaowen Huang
Keyword(s):  
Phase Transformation ◽  
Volume Fraction ◽  
Austenite Formation ◽  
Steel Matrix ◽  
Transformation Kinetics ◽  
Bainite Transformation ◽  
Continuous Cooling ◽  
The Matrix ◽  
Dimensional Growth ◽  
Kinetics Of

In this study, the phase transformation behaviour of the carburised layer and the matrix of 23CrNi3Mo steel was comparatively investigated by constructing continuous cooling transformation (CCT) diagram, determining the volume fraction of retained austenite (RA) and plotting dilatometric curves. The results indicated that Austenite formation start temperature (Ac1) and Austenite formation finish temperature (Ac3) of the carburised layer decreased compared to the matrix, and the critical cooling rate (0.05 °C/s) of martensite transformation is significantly lower than that (0.8 °C/s) of the matrix. The main products of phase transformation in both the carburised layer and the matrix were martensite and bainite microstructures. Moreover, an increase in carbon content resulted in the formation of lamellar martensite in the carburised layer, whereas the martensite in the matrix was still lath. Furthermore, the volume fraction of RA in the carburised layer was higher than that in the matrix. Moreover, the bainite transformation kinetics of the 23CrNi3Mo steel matrix during the continuous cooling process indicated that the mian mechanism of bainite transformation of the 23CrNi3Mo steel matrix is two-dimensional growth and one-dimensional growth.

scholarly journals In-Situ High-Energy X-ray Diffraction Study of Austenite Decomposition During Rapid Cooling and Isothermal Holding in Two HSLA Steels

2021 ◽  
Vol 52 (5) ◽  
pp. 1812-1825
Author(s):  
Sen Lin ◽  
Ulrika Borggren ◽  
Andreas Stark ◽  
Annika Borgenstam ◽  
Wangzhong Mu ◽  
...  
Keyword(s):  
Isothermal Holding ◽  
Weight Percent ◽  
High Energy ◽  
Decomposition Kinetics ◽  
Bainitic Transformation ◽  
Austenite Decomposition ◽  
X Ray Diffraction ◽  
Rapid Cooling ◽  
X Ray

AbstractIn-situ high-energy X-ray diffraction experiments with high temporal resolution during rapid cooling (280 °C s−1) and isothermal heat treatments (at 450 °C, 500 °C, and 550 °C for 30 minutes) were performed to study austenite decomposition in two commercial high-strength low-alloy steels. The rapid phase transformations occurring in these types of steels are investigated for the first time in-situ, aiding a detailed analysis of the austenite decomposition kinetics. For the low hardenability steel with main composition Fe-0.08C-1.7Mn-0.403Si-0.303Cr in weight percent, austenite decomposition to polygonal ferrite and bainite occurs already during the initial cooling. However, for the high hardenability steel with main composition Fe-0.08C-1.79Mn-0.182Si-0.757Cr-0.094Mo in weight percent, the austenite decomposition kinetics is retarded, chiefly by the Mo addition, and therefore mainly bainitic transformation occurs during isothermal holding; the bainitic transformation rate at the isothermal holding is clearly enhanced by lowered temperature from 550 °C to 500 °C and 450 °C. During prolonged isothermal holding, carbide formation leads to decreased austenite carbon content and promotes continued bainitic ferrite formation. Moreover, at prolonged isothermal holding at higher temperatures some degenerate pearlite form.

scholarly journals Heat Treatment Design for a QP Steel: Effect of Partitioning Temperature

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1136
Author(s):  
Marcel Carpio ◽  
Jessica Calvo ◽  
Omar García ◽  
Juan Pablo Pedraza ◽  
José María Cabrera
Keyword(s):  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Quenching Temperature ◽  
Advanced High Strength Steels ◽  
New Family ◽  
Automotive Parts ◽  
Fresh Martensite ◽  
Industry Needs

Designing a new family of advanced high-strength steels (AHSSs) to develop automotive parts that cover early industry needs is the aim of many investigations. One of the candidates in the 3rd family of AHSS are the quenching and partitioning (QP) steels. These steels display an excellent relationship between strength and formability, making them able to fulfill the requirements of safety, while reducing automobile weight to enhance the performance during service. The main attribute of QP steels is the TRIP effect that retained austenite possesses, which allows a significant energy absorption during deformation. The present study is focused on evaluating some process parameters, especially the partitioning temperature, in the microstructures and mechanical properties attained during a QP process. An experimental steel (0.2C-3.5Mn-1.5Si (wt%)) was selected and heated according to the theoretical optimum quenching temperature. For this purpose, heat treatments in a quenching dilatometry and further microstructural and mechanical characterization were carried out by SEM, XRD, EBSD, and hardness and tensile tests, respectively. The samples showed a significant increment in the retained austenite at an increasing partitioning temperature, but with strong penalization on the final ductility due to the large amount of fresh martensite obtained as well.

scholarly journals A New Systematic Approach Based on Dilatometric Analysis to Track Bainite Transformation Kinetics and the Influence of the Prior Austenite Grain Size

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 324
Author(s):  
David San-Martin ◽  
Matthias Kuntz ◽  
Francisca G. Caballero ◽  
Carlos Garcia-Mateo
Keyword(s):  
Heat Treatment ◽  
Grain Size ◽  
Prior Austenite ◽  
Bainitic Transformation ◽  
Transformation Rate ◽  
Transformation Kinetics ◽  
Austenite Grain Size ◽  
Austenite Grain ◽  
Prior Austenite Grain Size ◽  
Prior Austenite Grain

This investigation explores the influence of the austenitisation heat treatment and thus, of the prior austenite grain size (PAGS), on the kinetics of the bainitic transformation, using as A case study two high-carbon, high-silicon, bainitic steels isothermally transformed (TIso = 250, 300, 350 °C), after being austenised at different temperatures (γTγ = 925–1125 °C). A methodology, based on the three defining dilatometric parameters extracted from the derivative of the relative change in length, was proposed to analyse the transformation kinetics. These parameters are related to the time to start bainitic transformation, the time lapse for most of the transformation to take place and the transformation rate at the end of the transformation. The results show that increasing the PAGS up to 70 µm leads to an increase in the bainite nucleation rate, this effect being more pronounced for the lowest TIso. However, the overall transformation kinetics seems to be weakly affected by the applied heat treatment (γTγ and TIso). In one of the steels, PAGS > 70 µm (γTγ > 1050 °C), which weakly affects the progress of the transformation, except for TIso = 250 °C, for which the enhancement of the autocatalytic effect could be the reason behind an acceleration of the overall transformation.

scholarly journals Mathematical Modelling of Bainite Transformation Kinetics

1997 ◽  
Vol 07 (C5) ◽  
pp. C5-41-C5-46 ◽  
Author(s):  
N. A. Chester ◽  
H. K.D.H. Bhadeshia
Keyword(s):  
Mathematical Modelling ◽  
Transformation Kinetics ◽  
Bainite Transformation

CHARACTERIZATION OF HYDROXYAPATITE/TI6AL4V COMPOSITE POWDER UNDER VARIOUS SINTERING TEMPERATURE

2015 ◽  
Vol 75 (7) ◽  
Author(s):  
Amir Arifin ◽  
Abu Bakar Sulong ◽  
Norhamidi Muhamad ◽  
Junaidi Syarif
Keyword(s):  
Mechanical Properties ◽  
Composite Powder ◽  
Sintering Temperature ◽  
Physical And Mechanical Properties ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Different Temperatures ◽  
Two Phases ◽  
Work Interaction

Hydroxyapatite (HA) has been widely used in biomedical applications due to its excellent biocompatibility. However, Hydroxyapatite possesses poor mechanical properties and only tolerate limited loads for implants. Titanium is well-known materials applied in implant that has advantage in mechanical properties but poor in biocompatibility. The combination of the Titanium alloy and HA is expected to produce bio-implants with good in term of mechanical properties and biocompatabilty. In this work, interaction and mechanical properties of HA/Ti6Al4V was analyzed. The physical and mechanical properties of HA/Ti6Al4V composite powder obtained from compaction (powder metallurgy) of 60 wt.% Ti6Al4V and 40 wt.% HA and sintering at different temperatures in air were investigated in this study. Interactions of the mixed powders were investigated using X-ray diffraction. The hardness and density of the HA/Ti6Al4V composites were also measured. Based on the results of XRD analysis, the oxidation of Ti began at 700 °C. At 1000 °C, two phases were formed (i.e., TiO2 and CaTiO3). The results showed that the hardness HA/Ti6Al4V composites increased by 221.6% with increasing sintering temperature from 700oC to 1000oC. In contrast, the density of the composites decreased by 1.9% with increasing sintering temperature. 

scholarly journals Effect of Quenching and Partitioning Temperatures in the Q-P Process on the Properties of AHSS with Various Amounts of Manganese and Silicon

2012 ◽  
Vol 706-709 ◽  
pp. 2734-2739 ◽  
Author(s):  
Hana Jirková ◽  
Ludmila Kučerová ◽  
Bohuslav Mašek
Keyword(s):  
Tensile Strength ◽  
Retained Austenite ◽  
Isothermal Holding ◽  
Bainitic Ferrite ◽  
High Strength Steels ◽  
High Strength ◽  
Experimental Program ◽  
Quenching Temperature ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels

The use of the combined influence of retained austenite and bainitic ferrite to improve strength and ductility has been known for many years from the treatment of multiphase steels. Recently, the very fine films of retained austenite along the martensitic laths have also become the centre of attention. This treatment is called the Q-P process (quenching and partitioning). In this experimental program the quenching temperature and the isothermal holding temperature for diffusion carbon distribution for three advanced high strength steels with carbon content of 0.43 % was examined. The alloying strategies have a different content of manganese and silicon, which leads to various martensite start and finish temperatures. The model treatment was carried out using a thermomechanical simulator. Tested regimes resulted in a tensile strength of over 2000MPa with a ductility of above 14 %. The increase of the partitioning temperature influenced the intensity of martensite tempering and caused the decrease of tensile strength by 400MPa down to 1600MPa and at the same time more than 10 % growth of ductility occurred, increasing it to more than 20%.

Sign in / Sign up

Export Citation Format

Share Document