A Stiffness Surface Method to Analyze the Cross-Sectional Mechanical Properties of Reinforced Thermoplastic Pipes Subjected to Axisymmetric Loads

2021 ◽  
Vol 20 (4) ◽  
pp. 811-822
Author(s):  
Wencheng Liu ◽  
Shuqing Wang
Keyword(s):  
Mechanical Properties ◽  
Cross Sectional ◽  
Surface Method ◽  
The Cross

Comparison of the Cross Sectional Area, the Loss in Volume and the Mechanical Properties of LAE442 and MgCa0.8 as Resorbable Magnesium Alloy Implants after 12 Months Implantation Duration

2010 ◽  
Vol 638-642 ◽  
pp. 675-680 ◽  
Author(s):  
Martina Thomann ◽  
Nina von der Höh ◽  
Dirk Bormann ◽  
Dina Rittershaus ◽  
C. Krause ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cross Sections ◽  
Degradation Process ◽  
Cross Sectional Area ◽  
Bending Test ◽  
Sectional Area ◽  
Cross Sectional ◽  
Initial Strength ◽  
Three Point Bending ◽  
The Cross

Current research focuses on magnesium based alloys in the course of searching a resorbable osteosynthetic material which provides sufficient mechanical properties besides a good biocompatibility. Previous studies reported on a favorable biocompatibility of the alloys LAE442 and MgCa0.8. The present study compared the degradation process of cylindrical LAE442 and MgCa0.8 implants after 12 months implantation duration. Therefore, 10 extruded implants (2.5 x 25 mm, cross sectional area 4.9 mm²) of both alloys were implanted into the medullary cavity of both tibiae of rabbits for 12 months. After euthanization, the right bone-implant-compound was scanned in a µ-computed tomograph (µCT80, ScancoMedical) and nine uniformly distributed cross-sections of each implant were used to determine the residual implants´ cross sectional area (Software AxioVisionRelease 4.5, Zeiss). Left implants were taken out of the bone carefully. After weighing, a three-point bending test was carried out. LAE442 implants degraded obviously slower and more homogeneously than MgCa0.8. The mean residual cross sectional area of LAE442 implants was 4.7 ± 0.07 mm². MgCa0.8 showed an area of only 2.18 ± 1.03 mm². In contrast, the loss in volume of LAE442 pins was more obvious. They lost 64 % of their initial weight. The volume of MgCa0.8 reduced clearly to 54.4 % which corresponds to the cross sectional area results. Three point bending tests revealed that LAE442 showed a loss in strength of 71.2 % while MgCa0.8 lost 85.6 % of its initial strength. All results indicated that LAE442 implants degraded slowly, probably due to the formation of a very obvious degradation layer. Degradation of MgCa0.8 implants was far advanced.

Effects of cross-sessional area and aspect ratio coupled with orientation on mechanical properties and deformation behavior of Cu nanowires

2021 ◽  
Author(s):  
Hui Cao ◽  
Wenke Chen ◽  
Zhiyuan Rui ◽  
Changfeng Yan
Keyword(s):  
Mechanical Properties ◽  
Aspect Ratio ◽  
Yield Stress ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Cross Sectional Area ◽  
Sectional Area ◽  
Cross Sectional ◽  
Cu Nanowires ◽  
The Cross

Abstract Metal nanomaterials exhibit excellent mechanical properties compared with corresponding bulk materials and have potential applications in various areas. Despite a number of studies of the size effect on Cu nanowires mechanical properties with square cross-sectional, investigations of them in rectangular cross-sectional with various sizes at constant volume are rare, and lack of multifactor coupling effect on mechanical properties and quantitative investigation. In this work, the dependence of mechanical properties and deformation mechanisms of Cu nanowires/nanoplates under tension on cross-sessional area, aspect ratio of cross-sectional coupled with orientation were investigated using molecular dynamics simulations and the semi-empirical expressions related to mechanical properties were proposed. The simulation results show that the Young’s modulus and the yield stress sharply increase with the aspect ratio except for the <110>{110}{001} Cu nanowires/nanoplates at the same cross-sectional area. And the Young’s modulus increases while the yield stress decreases with the cross-sectional area of Cu nanowires. However, both of them increase with the cross-sectional area of Cu nanoplates. Besides, the Young’s modulus increases with the cross-sectional area at all the orientations. The yield stress shows a mildly downward trend except for the <111> Cu nanowires with increased cross-sectional area. For the Cu nanowires with a small cross-sectional area, the surface force increases with the aspect ratio. In contrast, it decreases with the aspect ratio increase at a large cross-sectional area. At the cross-sectional area of 13.068 nm2, the surface force decreases with the aspect ratio of the <110> Cu nanowires while it increases at other orientations. The surface force is a linearly decreasing function of the cross-sectional area at different orientations. Quantitative studies show that Young’s modulus and yield stress to the aspect ratio of the Cu nanowires satisfy exponent relationship. In addition, the main deformation mechanism of Cu nanowires is the nucleation and propagation of partial dislocations while it is the twinning-dominated reorientation for Cu nanoplates.

Bleaching Effects on Color, Chemical, and Mechanical Properties of White Spot Lesions

2016 ◽  
Vol 41 (3) ◽  
pp. 318-326 ◽  
Author(s):  
Y Kim ◽  
HH Son ◽  
K Yi ◽  
JS Ahn ◽  
J Chang
Keyword(s):  
Mechanical Properties ◽  
Hardness Test ◽  
Knoop Hardness ◽  
White Spot ◽  
Control Group ◽  
White Spot Lesions ◽  
Lesion Area ◽  
Experimental Conditions ◽  
Cross Sectional ◽  
The Cross

SUMMARY Objective: The purpose of the study was to evaluate the effect of bleaching on teeth with white spot lesions. Methods and Materials: Carious lesions with standardized whiteness were produced on the buccal and lingual surfaces of human premolars by pH cycling. Specimens were subjected to four experimental conditions (n=20/group) as follows: group 1, control; group 2, caries formation followed by remineralization using fluoride-containing casein phosphopeptide–amorphous calcium phosphate (CPP-ACP; Tooth Mousse Plus, GC, Tokyo, Japan); group 3, caries formation followed by bleaching using 10% carbamide peroxide; and group 4, caries formation followed by both bleaching and remineralization. The CIE L*a*b* color values were measured with a spectroradiometer, the mineral content was measured with electron probe microanalysis (EPMA) on the cross-sectional surface of each specimen, and the Knoop hardness test was carried out along the EPMA scan line. Two-way analysis of variance was performed with Tukey post hoc comparison. Results: The change in the CIE color values was not significantly different between the caries-formed (ΔE*=7.03) and the bleached enamel (ΔE*=7.60). Bleaching of the carious enamel extended the whiteness (ΔE*=3.38) without additional mineral loss (p&lt;0.05). The remineralization treatment significantly increased the calcium (Ca), phosphate (P), and fluoride content of the subsurface lesion area (p&lt;0.05). The cross-sectional microhardness values correlated well with the Ca and P content (R&gt;0.80). Conclusions: Bleaching reduced the color disparities between sound and carious enamel without deteriorating the chemical and mechanical properties. The application of CPP-ACP paste enhanced mineral deposition in the subsurface lesion area of carious enamel.

Semicrystalline Structure and Mechanical Properties of Polyolefin-Based Materials

2012 ◽  
Vol 441 ◽  
pp. 713-716
Author(s):  
Mizue Kuriyagawa ◽  
Koh Hei Nitta
Keyword(s):  
Mechanical Properties ◽  
Cross Section ◽  
Draw Ratio ◽  
Structural Model ◽  
Point Of View ◽  
Cross Sectional ◽  
Molecular Weights ◽  
The Cross ◽  
Sectional Shape ◽  
Structural Point

The mechanical yielding and necking behaviors of metallocene-catalyzed high density polyethylenes were investigated from a structural point of view. In particular the natural draw ratio was investigated with different crosshead speeds, molecular weights, and the cross-section shapes of sample specimens. We proposed a structural model for explaining the necking formation in addition to the molecular weight and the cross-sectional shape dependences of the natural draw ratio.

Sensitivities in the Production and Design of EPDM Rubber Springs

2002 ◽  
Vol 75 (2) ◽  
pp. 265-274 ◽  
Author(s):  
N. Naveh ◽  
J. Vittoser ◽  
Z. Glikman ◽  
S. Putter
Keyword(s):  
Mechanical Properties ◽  
Elastic Moduli ◽  
Cross Sectional ◽  
Epdm Rubber ◽  
Crosslinker Content ◽  
Design Production ◽  
Useful Life ◽  
Extended Program ◽  
The Cross ◽  
Sectional Shape

Abstract Modeling and robustness are two major concerns in the design and fabrication of rubber springs. This work is part of an extended program to investigate the relationships between rubber formulation, spring design, production variables, and spring performance throughout their useful life. The robustness of an EPDM compound to variations in composition or process parameters has been evaluated. The effect of crosslinker content, source of carbon black and mixing, was assessed in terms of standard mechanical properties. The elastic moduli were measured on lab size specimens and used to successfully model the behavior of a large toroidal rubber spring. Modeling included tailoring the cross-sectional shape and chamfering the corners to reduce strain levels, thus enabling spring compression up to 25% of its height with moderate strain. The spring behavior is unaffected by the scatter in friction at assembly stage or during service. The cross-sectional shape is shown to be a major factor in the spring behavior.

scholarly journals Influence of the Cross–Sectional Shape and Corner Radius on the Compressive Behaviour of Concrete Columns Confined by FRP and Stirrups

Polymers ◽  
2022 ◽  
Vol 14 (2) ◽  
pp. 341
Author(s):  
Yang Wei ◽  
Yang Xu ◽  
Gaofei Wang ◽  
Xunyu Cheng ◽  
Guofen Li
Keyword(s):  
Mechanical Properties ◽  
Axial Compression ◽  
Concrete Columns ◽  
Confined Concrete ◽  
Compression Tests ◽  
Cross Sectional ◽  
Compressive Behaviour ◽  
Corner Radius ◽  
The Cross ◽  
Sectional Shape

Axial compression tests were carried out on 72 FRP (fiber reinforced polymer)–stirrup composite−confined concrete columns. Stirrups ensure the residual bearing capacity and ductility after the FRP fractures. To reduce the effect of stress concentration at the corners of the confined square−section concrete columns and improve the restraint effect, an FRP–stirrup composite−confined concrete structure with rounded corners is proposed. Different corner radii of the stirrup and outer FRP were designed, and the corner radius of the stirrup was adjusted accurately to meet the designed corner radius of the outer FRP. The cross−section of the specimens gradually changed from square to circular as the corner radius increased. The influence of the cross−sectional shape and corner radius on the compressive behaviour of FRP–stirrup composite−confined concrete was analysed. An increase in the corner radius can cause the strain distribution of the FRP to be more uniform and strengthen the restraint effect. The larger the corner radius of the specimen, the better the improvement of mechanical properties. The strength of the circular section specimen was greatly improved. In addition, the test parameters also included the FRP layers, FRP types and stirrup spacing. With the same corner radius, increasing the number of FRP layers or densifying the stirrup spacing effectively improved the mechanical properties of the specimens. Finally, a database of FRP–stirrup composite−confined concrete column test results with different corner radii was established. The general calculation models were proposed, respectively, for the peak points, ultimate points and stress–strain models that are applicable to FRP−, stirrup− and FRP–stirrup−confined concrete columns with different cross−sectional shapes under axial compression.

A Simple Method for the Cross-Section Area Determination of Single Profiled Fibers and Its Application

2018 ◽  
Vol 24 (1) ◽  
pp. 17-28 ◽  
Author(s):  
Zhangchuan Peng ◽  
Chun Liu ◽  
Lin Zhang ◽  
Wei Li ◽  
Wenbo Hu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cross Section ◽  
Large Scale ◽  
Frozen Section ◽  
Ratio Method ◽  
Cross Sectional ◽  
Simple Method ◽  
The Cross ◽  
Profiled Fibers

AbstractOne of the critical prerequisites for accurately measuring the mechanical properties of profiled fibers is the precise determination of their cross-sectional areas (CSAs). In this study, a new method is established for determining a single profiled fibers’ CSA based on the frozen section method and digital photo, pixel-ratio method (FS-DP). FS-DP is used to obtain a transverse section of a fiber, by acquiring an image of the cross section using optical microscopy or scanning electron microscopy, and then calculating the CSA using Photoshop. Using FS-DP, it was found that the shape of a fiber of silk changes little in a range of 50 μm, but varies considerably over a range of 1 m, while the CSA of cocoon silk (900 m) first increases and then decreases. Mechanical property tests showed that the elongation, strength, elastic modulus, and toughness values of the cocoon silk are consistent with those reported previously. Additionally, FS-DP was also used to observe other profiled fibers. The application tests indicated that FS-DP can be used to quickly and accurately obtain the CSA of a single profiled fiber, and that it is suitable for the large-scale determination and analysis of the mechanical properties of profiled fibers.

scholarly journals Cross-Sectional Performance of Hollow Square Prisms with Rounded Edges

Symmetry ◽  
2020 ◽  
Vol 12 (6) ◽  
pp. 996
Author(s):  
Hiroyuki Shima ◽  
Nao Furukawa ◽  
Yuhei Kameyama ◽  
Akio Inoue ◽  
Motohiro Sato
Keyword(s):  
Mechanical Properties ◽  
Mathematical Model ◽  
Cross Sections ◽  
Cross Sectional ◽  
Hollow Section ◽  
Buckling Resistance ◽  
The Cross ◽  
The Stability ◽  
External Forces ◽  
Sectional Shape

Hollow-section columns are one of the mechanically superior structures with high buckling resistance and high bending stiffness. The mechanical properties of the column are strongly influenced by the cross-sectional shape. Therefore, when evaluating the stability of a column against external forces, it is necessary to reproduce the cross-sectional shape accurately. In this study, we propose a mathematical method to describe a polygonal section with rounded edges and vertices. This mathematical model would be quite useful for analyzing the mechanical properties of plants and designing plant-mimicking functional structures, since the cross-sections of the actual plant culms and stems often show rounded polygons.

scholarly journals Steady analysis of transcritical flows in collapsible tubes with discontinuous mechanical properties: implications for arteries and veins

2013 ◽  
Vol 736 ◽  
pp. 195-215 ◽  
Author(s):  
A. Siviglia ◽  
M. Toffolon
Keyword(s):  
Mechanical Properties ◽  
Free Surface Flows ◽  
Cross Sectional Area ◽  
Sectional Area ◽  
Collapsible Tube ◽  
Cross Sectional ◽  
Collapsible Tubes ◽  
The Cross ◽  
Transcritical Flows ◽  
Arteries And Veins

AbstractWe study the conditions under which discontinuous mechanical properties of a collapsible tube can induce transcritical flows, i.e. the transition through the critical state where the speed index (analogous to the Mach or the Froude numbers for compressible and free surface flows, respectively) is one. Such a critical transition may strongly modify the flow properties, cause a significant reduction in the cross-sectional area of the tube, and limit the flow. General relationships are obtained for a short segment using a one-dimensional model under steady flow conditions. Marginal curves delimiting the transcritical regions are identified in terms of the speed index and the cross-sectional area ratio. Since there are many examples of such flows in physiology and medicine, we also analyse the specific case of prosthesis (graft or stent) implantation in blood vessels. We then compute transcritical conditions for the case of stiffness and reference area variations, considering a collapsible tube characterized by physiological parameters representative of both arteries and veins. The results suggest that variations in mechanical properties may induce transcritical flow in veins but is unrealistic in arteries.

Tensile mechanical properties of human forearm tendons

2015 ◽  
Vol 40 (7) ◽  
pp. 711-719 ◽  
Author(s):  
J. F. Weber ◽  
A. M. R. Agur ◽  
A. Y. Fattah ◽  
K. D. Gordon ◽  
M. L. Oliver
Keyword(s):  
Mechanical Properties ◽  
Biomechanical Properties ◽  
Cross Sectional Area ◽  
Sectional Area ◽  
Visual Estimation ◽  
Cross Sectional ◽  
Laser Reflectance ◽  
Human Forearm ◽  
Fresh Frozen ◽  
The Cross

Previous studies of the mechanical properties of tendons in the upper limb have used embalmed specimens or sub-optimal methods of measurement. The aim of this study was to determine the biomechanical properties of all tendons from five fresh frozen cadaveric forearms using updated methodology. The cross-sectional area of tendons was accurately measured using a laser reflectance system. Tensile testing was done in a precision servo-hydraulic device with cryo-clamp fixation. We determined that the cross-sectional area of some tendons is variable and directly influences the calculated material properties; visual estimation of this is unreliable. Data trends illustrate that digital extensor tendons possess the greatest tensile strength and a higher Young’s modulus than other tendon types.

Sign in / Sign up

Export Citation Format

Share Document