scholarly journals Porogen Effect of Bioactive Glass on Poly(L-lactide) Scaffolds: Evidences by Electron Microscopy

2008 ◽  
Vol 14 (S3) ◽  
pp. 65-66
Author(s):  
N.B. Barroca ◽  
A.L. Daniel-da-Silva ◽  
M.H.V. Fernandes ◽  
P.M. Vilarinho
Keyword(s):  
Mechanical Properties ◽  
Bioactive Glass ◽  
Average Pore Size ◽  
Physical And Mechanical Properties ◽  
Ceramic Composites ◽  
Porous Polymer ◽  
Bioactive Glasses ◽  
Average Pore ◽  
Thermally Induced ◽  
Ceramic Fillers

Recently, porous polymer-ceramic composites have been developed and represent promising scaffolds to be used as synthetic extracellular matrix in bone tissue engineering since they combine the advantages of these two types of materials. On the other hand bioactive glasses (BG) have been used as ceramic fillers to promote bioactivity and to enhance mechanical properties and osteoblast functions. Among all the requirements, these 3D porous structures should have a controllable average pore size larger than 100 μm as well as good pore interconnectivity to allow vascularization and tissue ingrowth. The goal of this study is to investigate the effect of the addition of a bioactive glass on the porous structure development of the scaffolds prepared by thermally induced phase-separation and also to test the bioactivity of these composite scaffolds. Poly (L-lactic) acid (PLLA) was chosen as the polymer matrix because of its well-known biocompatibility and adjustable physical and mechanical properties. Micron-sized (<10 μm) glass from the 3CaO.P2O5-MgO-SiO2 system was produced in our laboratory and used as the bioactive ceramic filler.

Structural and Mechanical Properties of Bioactive Glass–Ceramic Composites

2016 ◽  
Vol 55 (3-4) ◽  
pp. 172-184 ◽  
Author(s):  
O. R. Parkhomei ◽  
N. D. Pinchuk ◽  
O. E. Sych ◽  
T. V. Tomila ◽  
G. B. Tovstonog ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Bioactive Glass ◽  
Glass Ceramic ◽  
Ceramic Composites

scholarly journals Physicochemical and Mechanical Properties of Blow Spun Nanofibrous Prostheses Modified with Acrylic Acid and REDV Peptide

Coatings ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1110
Author(s):  
Beata A. Butruk-Raszeja ◽  
Aleksandra Kuźmińska ◽  
Michał Wojasiński ◽  
Zuzanna Piotrowska
Keyword(s):  
Mechanical Properties ◽  
Fiber Diameter ◽  
Flow System ◽  
Average Pore Size ◽  
Internal Diameter ◽  
Optimal Parameters ◽  
Average Pore ◽  
Vascular Prostheses ◽  
Modification Process ◽  
Inner Surface

The paper presents a method of modifying the inner surface of nanofibrous vascular prostheses. The modification process involves two steps: introducing a hydrophilic linker, followed by a peptide containing the arginine-glutamic acid-aspartic acid-valine (REDV) sequence. The influence of the process parameters (reaction time, temperature, initiator concentration) on morphology and the distribution of fiber diameters were examined. For selected optimal parameters, the prostheses were modified in the flow system. Modifications along the entire length of the prosthesis were confirmed—the inlet and the outlet areas showed no significant (p > 0.05) differences in the value of the contact angle and the analyzed morphological parameters. The basic physicochemical and mechanical properties of modified prostheses were analyzed. The study showed that REDV-modified prosthesis has an average fiber diameter of 318 ± 99 nm, the average pore size of 3.0 ± 1.6 μm, the porosity of 48.4 ± 8.6% and Young’s modulus of 4.0 ± 0.4 MPa. The internal diameter of prostheses remains unchained and amounts to 3 mm. Such modified prostheses can reduce the risk of blood coagulation by increasing the surface’s wettability and, most of all, by introducing endothelial cell-selective peptide. As an effect, the proposed surfaces could recruit endothelial progenitor cells directly from the bloodstream and promote the endothelium formation after implantation.

scholarly journals A New Generation of Electrospun Fibers Containing Bioactive Glass Particles for Wound Healing

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5651
Author(s):  
Rachele Sergi ◽  
Valeria Cannillo ◽  
Aldo R. Boccaccini ◽  
Liliana Liverani
Keyword(s):  
Mechanical Properties ◽  
Wound Healing ◽  
Bioactive Glass ◽  
Flexible Structures ◽  
Biological Properties ◽  
Cellular Viability ◽  
Bioactive Glasses ◽  
Electrospinning Technique ◽  
Potential Applications ◽  
Biological Performance

Chitosan fibers blended with polyethylene oxide (CHIT_PEO) and crosslinked with genipin were fabricated by electrospinning technique. Subsequently, CHIT_PEO bioactive glass composite electrospun mats were fabricated with the aim to achieve flexible structures with adequate mechanical properties and improved biological performance respect to CHIT_PEO fibers, for potential applications in wound healing. Three different compositions of bioactive glasses (BG) were selected and investigated: 45S5 BG, a Sr and Mg containing bioactive glass (BGMS10) and a Zn-containing bioactive glass (BGMS_2Zn). Particulate BGs (particles size < 20 μm) were separately added to the starting CHIT_PEO solution before electrospinning. The two recently developed bioactive glasses (BGMS10 and BGMS_2Zn) showed very promising biological properties in terms of bioactivity and cellular viability; thus, such compositions were added for the first time to CHIT_PEO solution to fabricate composite electrospun mats. The incorporation of bioactive glass particles and their distribution into CHIT_PEO fibers were assessed by SEM and FTIR analyses. Furthermore, CHIT_PEO composite electrospun mats showed improved mechanical properties in terms of Young’s Modulus compared to neat CHIT_PEO fibers; on the contrary, the values of tensile strain at break (%) were comparable. Biological performance in terms of cellular viability was investigated by means of WST-8 assay and CHIT_PEO composite electrospun mats showed cytocompatibility and the desired cellular viability.

Effect of Carbon Particle Size and Content on the Mechanical and Thermal Properties of Recycled SLS Glass Composite

2016 ◽  
Vol 694 ◽  
pp. 34-38
Author(s):  
Zaleha Mustafa ◽  
Zurina Shamsudin ◽  
Radzali Othman ◽  
Nur Fashiha Sapari ◽  
Jariah Mohd Juoi ◽  
...  
Keyword(s):  
Particle Size ◽  
Thermal Properties ◽  
Average Pore Size ◽  
Carbon Particle ◽  
Physical And Mechanical Properties ◽  
Waste Glass ◽  
Mechanical And Thermal Properties ◽  
Glass Composite ◽  
Average Pore ◽  
Glass Composites

Glass-composite materials were prepared from the soda lime silicate (SLS) waste glass; ball clay and charcoal powder were fired to temperature of 850 °C as an effort for recycling waste glass. Various carbon contents, i.e., 1, 5, 10, 20 and 30 wt.% C were used to evaluate the effect of carbon contents on the hardness and thermal properties of glass composites. In addition, five different particles size (d0.5) of 1, 5, 20, 40 and 75 μm were used to observe the influence of particle size on the physical and mechanical properties of the glass composites. Phase analysis studies revealed the presence of quartz (ICDD: 00001-0649, 2θ = 25.6° and 35.6°), cristobalite (ICDD 00004-0379, 2θ = 22.0° and 38.4°) and wollastonite (ICDD 00002-0689, 2θ = 30.1° and 26.9°). The results showed that the optimised properties is at 1 wt.% of carbon content containing average pore size of 10 μm, with lowest porosity percentage of 1.76 %, highest Vickers microhardness of 4.6 GPa and minimum CTE. The percentage of porosity and hardness value also increased with reduction in carbon particle size.

Hybrid Bioactive Glass-Polyvinyl Alcohol Prepared by Sol-Gel

2008 ◽  
Vol 587-588 ◽  
pp. 62-66 ◽  
Author(s):  
Hermes S. Costa ◽  
Alexandra A.P. Mansur ◽  
Edel Figueiredo Barbosa-Stancioli ◽  
Marivalda Pereira ◽  
Herman S. Mansur
Keyword(s):  
Mechanical Properties ◽  
Polyvinyl Alcohol ◽  
Bioactive Glass ◽  
Sol Gel ◽  
Degree Of Hydrolysis ◽  
Bioactive Glasses ◽  
Composite Foams ◽  
Composition Ratios ◽  
Hybrid Scaffolds ◽  
Hydrolysis Of

Bioactive glasses are materials that have been used for the repair and reconstruction of diseased bone tissues, as they exhibit direct bonding with human bone tissues. However, bioactive glasses have low mechanical properties compared to cortical and cancellous bone. On the other hand, composite materials of biodegradable polymers with inorganic bioactive glasses are of particular interest to engineered scaffolds because they often show an excellent balance between strength and toughness and usually improved characteristics compared to their individual components. Composite bioactive glass-polyvinyl alcohol foams for use as scaffolds in tissue engineering were previously developed using the sol-gel route. The goal of this work was the synthesis of composite foams modified with higher amounts of PVA. Samples were characterized by morphological and chemical analysis. The mechanical behavior of the obtained materials was also investigated. The degree of hydrolysis of PVA, concentration of PVA solution and different PVA-bioactive glass composition ratios affect the synthesis procedure. Foams with up to 80 wt% polymer content were obtained. The hybrid scaffolds obtained exhibited macroporous structure with pore size varying from 50 to 600 µm and improved mechanical properties.

scholarly journals Alginate/Gelatin Hydrogels Reinforced with TiO2 and β-TCP Fabricated by Microextrusion-based Printing for Tissue Regeneration

Polymers ◽  
2019 ◽  
Vol 11 (3) ◽  
pp. 457 ◽  
Author(s):  
Rodrigo Urruela-Barrios ◽  
Erick Ramírez-Cedillo ◽  
A. Díaz de León ◽  
Alejandro Alvarez ◽  
Wendy Ortega-Lara
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Tissue Regeneration ◽  
Average Pore Size ◽  
Three Dimensional ◽  
Engineering Applications ◽  
Average Pore ◽  
Viscous Deformation ◽  
Freeze Dried ◽  
3D Printed

Three-dimensional (3D) printing technologies have become an attractive manufacturing process to fabricate scaffolds in tissue engineering. Recent research has focused on the fabrication of alginate complex shaped structures that closely mimic biological organs or tissues. Alginates can be effectively manufactured into porous three-dimensional networks for tissue engineering applications. However, the structure, mechanical properties, and shape fidelity of 3D-printed alginate hydrogels used for preparing tissue-engineered scaffolds is difficult to control. In this work, the use of alginate/gelatin hydrogels reinforced with TiO2 and β-tricalcium phosphate was studied to tailor the mechanical properties of 3D-printed hydrogels. The hydrogels reinforced with TiO2 and β-TCP showed enhanced mechanical properties up to 20 MPa of elastic modulus. Furthermore, the pores of the crosslinked printed structures were measured with an average pore size of 200 μm. Additionally, it was found that as more layers of the design were printed, there was an increase of the line width of the bottom layers due to its viscous deformation. Shrinkage of the design when the hydrogel is crosslinked and freeze dried was also measured and found to be up to 27% from the printed design. Overall, the proposed approach enabled fabrication of 3D-printed alginate scaffolds with adequate physical properties for tissue engineering applications.

scholarly journals Effect of Melt-Derived Bioactive Glass Particles on the Properties of Chitosan Scaffolds

2019 ◽  
Vol 10 (3) ◽  
pp. 38 ◽  
Author(s):  
Hamasa Faqhiri ◽  
Markus Hannula ◽  
Minna Kellomäki ◽  
Maria Teresa Calejo ◽  
Jonathan Massera
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Calcium Phosphate ◽  
Bioactive Glass ◽  
Pore Size ◽  
Glass Content ◽  
Micro Computed Tomography ◽  
Glass Composite ◽  
Composite Scaffolds ◽  
Bioactive Glasses

This study reports on the processing of three-dimensional (3D) chitosan/bioactive glass composite scaffolds. On the one hand, chitosan, as a natural polymer, has suitable properties for tissue engineering applications but lacks bioactivity. On the other hand, bioactive glasses are known to be bioactive and to promote a higher level of bone formation than any other biomaterial type. However, bioactive glasses are hard, brittle, and cannot be shaped easily. Therefore, in the past years, researchers have focused on the processing of new composites. Difficulties in reaching composite materials made of polymer (synthetic or natural) and bioactive glass include: (i) The high glass density, often resulting in glass segregation, and (ii) the fast bioactive glass reaction when exposed to moisture, leading to changes in the glass reactivity and/or change in the polymeric matrix. Samples were prepared with 5, 15, and 30 wt% of bioactive glass S53P4 (BonAlive ®), as confirmed using thermogravimetric analysis. MicrO–Computed tomography and optical microscopy revealed a flaky structure with porosity over 80%. The pore size decreased when increasing the glass content up to 15 wt%, but increased back when the glass content was 30 wt%. Similarly, the mechanical properties (in compression) of the scaffolds increased for glass content up to 15%, but decreased at higher loading. Ions released from the scaffolds were found to lead to precipitation of a calcium phosphate reactive layer at the scaffold surface. This is a first indication of the potential bioactivity of these materials. Overall, chitosan/bioactive glass composite scaffolds were successfully produced with pore size, machinability, and ability to promote a calcium phosphate layer, showing promise for bone tissue engineering and the mechanical properties can justify their use in non-load bearing applications.

scholarly journals A Comparison of Bioactive Glass Scaffolds Fabricated ‎by Robocasting from Powders Made by Sol–Gel and Melt-Quenching Methods

Processes ◽  
2020 ◽  
Vol 8 (5) ◽  
pp. 615
Author(s):  
Basam A. E. Ben-Arfa ◽  
Robert C. Pullar
Keyword(s):  
Mechanical Properties ◽  
Bioactive Glass ◽  
Bone Growth ◽  
Sol Gel ◽  
Glass Network ◽  
Silica Content ◽  
Bioactive Glasses ◽  
Phosphorous Content ◽  
High Silica ◽  
45S5 Bioglass

Bioactive glass scaffolds are used in bone and tissue biomedical implants, and there is great interest in their fabrication by additive manufacturing/3D printing techniques, such as robocasting. Scaffolds need to be macroporous with voids ≥100 m to allow cell growth and vascularization, biocompatible and bioactive, with mechanical properties matching the host tissue (cancellous bone for bone implants), and able to dissolve/resorb over time. Most bioactive glasses are based on silica to form the glass network, with calcium and phosphorous content for new bone growth, and a glass modifier such as sodium, the best known being 45S5 Bioglass®. 45S5 scaffolds were first robocast in 2013 from melt-quenched glass powder. Sol–gel-synthesized bioactive glasses have potential advantages over melt-produced glasses (e.g., greater porosity and bioactivity), but until recently were never robocast as scaffolds, due to inherent problems, until 2019 when high-silica-content sol–gel bioactive glasses (HSSGG) were robocast for the first time. In this review, we look at the sintering, porosity, bioactivity, biocompatibility, and mechanical properties of robocast sol–gel bioactive glass scaffolds and compare them to the reported results for robocast melt-quench-synthesized 45S5 Bioglass® scaffolds. The discussion includes formulation of the printing paste/ink and the effects of variations in scaffold morphology and inorganic additives/dopants.

Sign in / Sign up

Export Citation Format

Share Document