scholarly journals Soft channel formation and symmetry breaking in exotic active emulsions

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
L. N. Carenza ◽  
G. Gonnella ◽  
A. Lamura ◽  
D. Marenduzzo ◽  
G. Negro ◽  
...  
Keyword(s):  
Shear Rate ◽  
Rheological Properties ◽  
Self Assembly ◽  
Contractile Activity ◽  
Active Material ◽  
Fluid Flows ◽  
Shear Rates ◽  
Two Phases ◽  
The Stability ◽  
Isotropic Fluid

Abstract We use computer simulations to study the morphology and rheological properties of a bidimensional emulsion resulting from a mixture of a passive isotropic fluid and an active contractile polar gel, in the presence of a surfactant that favours the emulsification of the two phases. By varying the intensity of the contractile activity and of an externally imposed shear flow, we find three possible morphologies. For low shear rates, a simple lamellar state is obtained. For intermediate activity and shear rate, an asymmetric state emerges, which is characterized by shear and concentration banding at the polar/isotropic interface. A further increment in the active forcing leads to the self-assembly of a soft channel where an isotropic fluid flows between two layers of active material. We characterize the stability of this state by performing a dynamical test varying the intensity of the active forcing and shear rate. Finally, we address the rheological properties of the system by measuring the effective shear viscosity, finding that this increases as active forcing is increased—so that the fluid thickens with activity.

scholarly journals Use of helical ribbon mixer for measurement of rheological properties of fruit pulps

2013 ◽  
Vol 19 (No. 4) ◽  
pp. 148-153 ◽  
Author(s):  
P. Novotná ◽  
A. Landfeld ◽  
K. Kýhos ◽  
M. Houška ◽  
J. Strohalm
Keyword(s):  
Shear Rate ◽  
Rheological Properties ◽  
Flow Behaviour ◽  
Rotational Rheometer ◽  
Shear Rates ◽  
Coaxial Cylinders ◽  
Helical Ribbon ◽  
Flow Behaviour Index ◽  
Average Shear ◽  
Behaviour Index

Fruit pulps contain fine particles of the flesh of the original fruit that are suspended in the fruit juice. This suspension has a tendency to settling or separation during measurements of its rheological properties in the rotational rheometer with coaxial cylinders (especially if the greater gap is used). In this case the use of a mixer is convenient. The mixer can serve as a tool for measurement of rheological properties and at the same time it can prevent the settling and it is not sensitive to the occurrence of greater particles in the measured fluid. The helical ribbon mixer was used in this work for measurement of five samples of fruit pulp. The mixer was calibrated by the use of Newtonian fluid of known viscosity (honey). The radius of the inner cylinder of hypothetical rotational rheometer was predicted from the assumption that mixer and cylinder exhibit the same torque necessary for the rotation at the same rotational speed. The average shear rate in the mixed pulp was predicted by using the relation valid for power law fluids and rheometer with coaxial cylinders. The radius (where the average shear rate was calculated) was chosen by the requirement that the shear rate would be almost independent of changes in the flow behaviour index valid for measured pulps. Firstly the flow behaviour index was predicted as a slope of torque vs. rotational speed dependence in log-log co-ordinates. It was found that the flow behaviour index varies in the range 0.2–0.3. The radius was predicted from a graph where shear rates for 0.2 and 0.3 are the same. Then the average shear rates were calculated from rotational speeds for individual flow behaviour indexes. Rheological properties measured by using a mixer correspond to those measured with a rotational rheometer with coaxial cylinders satisfactorily only in the case that the creeping flow regime was kept in the mixed fluid. The fruit pulps are strongly non-Newtonian fluids with very low values of the flow behaviour index around 0.2.

scholarly journals Evaluating the potential of surface-modified silica nanoparticles using internal olefin sulfonate for enhanced oil recovery

2019 ◽  
Vol 17 (3) ◽  
pp. 722-733 ◽  
Author(s):  
Afaque Ahmed ◽  
Ismail Mohd Saaid ◽  
Abdelazim Abbas Ahmed ◽  
Rashidah M. Pilus ◽  
Mirza Khurram Baig
Keyword(s):  
Silica Nanoparticles ◽  
Rheological Properties ◽  
Oil Recovery ◽  
Displacement Efficiency ◽  
Shear Rates ◽  
Oil Water ◽  
Core Flood ◽  
The Stability ◽  
Modified Silica Nanoparticles ◽  
Surface Modified

AbstractRecently, nanoparticles have proven to enhance oil recovery on the core-flood scale in challenging high-pressure high-temperature reservoirs. Nanomaterials generally appear to improve oil production through wettability alteration and reduction in interfacial tension between oil and water phases. Besides, they are environmentally friendly and cost-effective enhanced oil recovery techniques. Studying the rheological properties of nanoparticles is critical for field applications. The instability of nanoparticle dispersion due to aggregation is considered as an unfavorable phenomenon in nanofluid flooding while conducting an EOR process. In this study, wettability behavior and rheological properties of surface-treated silica nanoparticles using internal olefins sulfonates (IOS20–24 and IOS19–23), anionic surfactants were investigated. Surface modification effect on the stability of the colloidal solution in porous media and oil recovery was inspected. The rheology of pure and surface-treated silica nanoparticles was investigated using a HPHT rheometer. Morphology and particle size distributions of pure and coated silica nanoparticles were studied using a field emission scanning electron microscope. A series of core-flood runs was conducted to evaluate the oil recovery factor. The coated silica nanoparticles were found to alter rheological properties and exhibited a shear-thinning behavior as the stability of the coated silica nanoparticles could be improved considerably. At low shear rates, the viscosity slightly increases, and the opposite happens at higher shear rates. Furthermore, the surface-modified silica nanoparticles were found to alter the wettability of the aqueous phase into strongly water-wet by changing the contact angle from 80° to 3° measured against glass slides representing sandstone rocks. Oil–water IFT results showed that the surface treatment by surfactant lowered the oil–water IFT by 30%. Also, the viscosity of brine increased from 0.001 to 0.008 Pa s by introducing SiO2 nanoparticles to the aqueous phase for better displacement efficiency during chemical-assisted EOR. The core-flood experiments revealed that the ultimate oil recovery is increased by approximately 13% with a surfactant-coated silica nanofluid flood after the conventional waterflooding that proves the potential of smart nanofluids for enhancing oil recovery. The experimental results imply that the use of surfactant-coated nanoparticles in tertiary oil recovery could facilitate the displacement efficiency, alter the wettability toward more water-wet and avoid viscous fingering for stable flood front and additional oil recovery.

Development of Viscosified Acid-Surfactant Solutions for Oilfield Applications: Rheological Properties

2020 ◽  
Vol 143 (2) ◽  
Author(s):  
Lionel Talley Fogang ◽  
Muhammad Shahzad Kamal ◽  
Mohamed Mahmoud
Keyword(s):  
Shear Rate ◽  
Acid Solution ◽  
Rheological Properties ◽  
Calcium Chloride ◽  
Elastic Properties ◽  
Salt Concentration ◽  
Shear Thinning ◽  
Rate Range ◽  
Shear Rates ◽  
Surfactant Solutions

Abstract Viscosified acids are desired in several oilfield applications such as in acid diversion and acid fracturing operations. The study aimed to delineate the rheological properties of a novel amine type surfactant and viscosified acid-surfactant solutions. The steady shear and dynamic rheological properties were evaluated by varying the surfactant, acid, and salt concentration. Such a study is required to gauge the suitability of the viscosifying agent in acid stimulation jobs. The surfactant solutions without acid showed shear-thinning behavior, whereas those with acid showed a Newtonian plateau over a wide shear rate range before undergoing shear thinning. This means that over a wide shear rate range, the acid-surfactant solutions become independent of applied shear. At low shear rates, the viscosity of the surfactant was higher compared with the surfactant-acid solution. However, at high shear rates, the viscosity of the surfactant was lower compared with the viscosity of the surfactant-acid solution. There was an optimal salt concentration that improved the viscosity and elasticity of the acid-surfactant solutions. Thus, the rheology of the surfactant solution can be improved by adding both acid and salt. The elastic properties of acid-surfactant solutions were also better compared with the elastic properties of pure surfactant. The addition of acid improved the elastic properties of the surfactant solutions. Constant viscosity over a range of shear rate is a suitable application for acid fracturing operations in which the acid leak-off will be minimal due to the high viscosity. Also, brines in most of the carbonate formation consist of high loading of calcium chloride which was found to have a positive effect on the viscosity. Increasing the calcium chloride leads to an increase in viscosity, and then subsequently decreases the viscosity. This shows that the acid and salt concentration plays a role in modifying the rheological properties of the surfactant solutions.

A Comparison of Rheological Models and Experimental Data of Metallocene Linear Low Density Polyethylene Solutions as a Function of Temperature and Concentration

2016 ◽  
Vol 12 (3) ◽  
pp. 4322-4339
Author(s):  
Salah Hamza
Keyword(s):  
Experimental Data ◽  
Shear Rate ◽  
Rheological Properties ◽  
Power Law ◽  
Low Density Polyethylene ◽  
Effect Of Temperature ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Shear Rates ◽  
Wide Range

Knowledge of rheological properties of polymer and their variation with temperature and concentration have been globally important for processing and fabrication of polymers in order to make useful products. Basheer et al. [1] investigated, experimentally, the changes in rheological properties of metallocene linear low density polyethylene (mLLDPE) solutions by using a rotational rheometer model AR-G2 with parallel plate geometry. Their work covered the temperature range from  to  and  concentration from  to . In this paper, we reconsider Basheer work to describe the rheological behavior of mLLDPE solutions and its dependence on concentration and temperature.Until now, several models have been built to describe the complex behavior of polymer fluids with varying degrees of success. In this article, Oldroyd 4-constant, Giesekus and Power law models were tested for investigating the viscosity of mLLDPE solution as a function of shear rate. Results showed that Giesekus and power law models provide the best prediction of viscosity for a wide range of shear rates at constant temperature and concentration. Therefore, Giesekus and power law models were suitable for all mLLDPE solutions while Oldroyd 4-constant model doesn't.A new proposed correlation for the viscosity of mLLDPE solutions as a function of shear rate, temperature and concentration has been suggested. The effect of temperature and concentration can be adequately described by an Arrhenius-type and exponential function respectively. The proposed correlation form was found to fit the experimental data adequately.

Thixotropy of aqueous solution of fluorocarbon-modified poly(acrylic acid)

e-Polymers ◽  
2009 ◽  
Vol 9 (1) ◽  
Author(s):  
Hongqi Hu ◽  
Lin Li ◽  
Mingcai Chen
Keyword(s):  
Aqueous Solution ◽  
Shear Rate ◽  
Acrylic Acid ◽  
Rheological Properties ◽  
Great Increase ◽  
Hydrophobic Association ◽  
Chain Elongation ◽  
Shear Rates ◽  
Viscosity Dependence ◽  
Poly Acrylic Acid

AbstractThe rheological properties of the aqueous solution of 1H,1H,11Hperfluoroundecyl acrylate -modified poly(acrylic acid) were studied. It was found that the solutions show different viscosity dependence on shear time at different pH and shear rates. At lower pH and moderate shear rates, the viscosity of the solutions shows a great increase with time. At pH 5.0 and above, it exhibits thixotropy at any shear rate, i.e., the viscosity decreases with time at constant shear rates. If the shearing stops, the viscosity of the solutions can be recovered to some extent. These phenomena are interpreted to be due to the intermolecular hydrophobic association: the construction of the association leads to an increase of the viscosity, the destroying of the association leads to a decrease of the viscosity. The pH-induced conformational change and the shearing-induced chain elongation jointly influence the intermolecular hydrophobic association.

scholarly journals Impact of organophilic clay on rheological properties of gasoil-based drilling muds

2020 ◽  
Vol 10 (8) ◽  
pp. 3533-3540
Author(s):  
Cheikh Bergane ◽  
Larbi Hammadi
Keyword(s):  
Shear Rate ◽  
Rheological Properties ◽  
Yield Stress ◽  
Drilling Mud ◽  
Flow Curves ◽  
Casson Model ◽  
Organophilic Clay ◽  
The Stability ◽  
Drilling Muds ◽  
The Impact

Abstract In this study, the impact of VG69 organophilic clay on the rheological properties of gasoil-based drilling muds (invert emulsions) was investigated. The flow curves of gasoil-based drilling muds as a function of the dose of VG69 organophilic clay were analyzed by the Casson model. The addition of VG69 organophilic clay with a quantity range between 0 and 5 g in gasoil-based drilling muds induces an increase in the yield stress and the viscosity at an infinite shear rate of drilling muds. It is also proven that the addition of VG69 organophilic clay leads to an increase in the viscoelastic and thixotropic properties of the drilling muds. The study of the stability of gasoil-based drilling muds by centrifugation showed that for a quantity of VG69 organophilic clay lower than 3 g, the stability of the drilling muds increases and for a quantity of VG69 organophilic clay higher than 3 g, their stability decreases. The results obtained showed that the addition of 3 g of VG69 organophilic clay to the gasoil-based drilling mud increased the yield stress by 230%, the viscosity at an infinite shear rate by 3.4% and it improved the mud stability by 70%.

scholarly journals Effect of Different Shear Rates on Particle Microstructure of Cementitious Materials in a Wide Gap Vane-in-cup Rheometer

Materials ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2035
Author(s):  
Mahmoud Eslami Pirharati ◽  
Hans-W. Krauss ◽  
Carsten Schilde ◽  
Dirk Lowke
Keyword(s):  
Shear Rate ◽  
Rheological Properties ◽  
Cement Paste ◽  
Particle Agglomeration ◽  
Shear Rates ◽  
Average Shear ◽  
Local Shear ◽  
Wide Gap ◽  
Agglomeration State ◽  
Shear History

Rheological properties of cementitious suspensions are affected not only by their mixture composition but also by process-related factors such as shear history. To enable a model-based description, investigations were carried out on the effect of shear history (shear rate variation over time) on the cement paste agglomeration state. Therefore, a Focused Beam Reflectance Measurement (FBRM) system and a wide gap rheometer were coupled to study the relation between shear history and in-situ chord length distribution simultaneously, indicating particle agglomeration. Hence, the effect of average shear rates (resulting from the applied shear profile), as well as shear rate distribution within the gap (local shear rates) on the particle agglomeration state have been investigated. The rheological properties of cement paste were evaluated with the Reiner–Riwlin approach. Furthermore, the agglomeration state of the particles was compared for different average shear rates and local shear rates at various positions of the FBRM probe. The results show that the median chord length increases in all positions when the average shear rate is decreased, indicating increasing particle agglomeration. Moreover, due to variable local shear rates at different FBRM probe positions, different agglomeration states are observed, resulting from two factors, shear rate dependent particle agglomeration and shear-induced particle migration.

Rheology and Component Interactions in Tape Casting Slurries

1985 ◽  
Vol 60 ◽  
Author(s):  
John R Morris ◽  
W Roger Cannon
Keyword(s):  
Shear Rate ◽  
Rheological Behavior ◽  
Tape Casting ◽  
Relative Viscosity ◽  
Shear Rates ◽  
Viscosity Measurements ◽  
The Stability ◽  
Low Shear

AbstractRheology and the component interactions which affect rheology were studied for a tape casting composition similar to commercial systems. Viscosity measurements at different shear rates were compared to measured tape properties to determine if high or low shear rate rheological behavior controls tape characteristics. Relative viscosity was measured to assess the contribution of each component to the stability of the dispersion.

scholarly journals Rheological properties of traditional balsamic vinegar: New insights and markers for objective and perceived quality

2017 ◽  
Vol 6 (1) ◽  
Author(s):  
Pasquale M. Falcone ◽  
Elisa Sabatinelli ◽  
Federico Lemmetti ◽  
Paolo Giudici
Keyword(s):  
Shear Rate ◽  
Rheological Properties ◽  
Dynamic Viscosity ◽  
Flow Instability ◽  
Relaxation Times ◽  
Sensory Properties ◽  
Flow Behaviour ◽  
Shear Rates ◽  
Wide Range ◽  
Balsamic Vinegar

The molecular structure of Traditional Balsamic Vinegar (TBV) undergoes shear-induced and time-dependent jamming transitions due to the high solute concentration and self-assembling phenomena of high molecular size melanoidins with very-long relaxation times (12 years at least or more than 25). The purpose of this work was to perform a descriptive and quantitativeevaluation of relationships between rheological properties, vinegar composition, and perceptual assessment of sensory properties according to the official sensory procedure. With this aim, vinegars having quality traits matching legal requirements for the PDO designation were analyzed for their reducing sugars (glucose and fructose), volatile acidity, fixed acidity, pH, Brix degree, and density as well as for their flow behaviour and dynamic viscosity over a wide range of shear rates. Results showed that flow behaviour of TBV was affected by jamming properties over wide-scale ranges of shear rate producing flow instability below a shear rate of 60s-1. Homogeneous, continuous flow was found at medium-high shear rates with thickening and/or thinning traits. A common onset for the structure scaling was mathematically estimated to occur close to when the density was 1.32 gmL-1. Comparative analysis of rheological, compositional and sensory properties suggested that the colloidal jamming of the vinegar melanoidins dominated the total olfactive and gustative stimuli, and determined the classification of the vinegars that had a higher dynamic viscosity but more homogeneous flow as being of the highest commercial quality category. A robust statistical model was proposed encoding for the top-down decision-making process for quality assignment according to the official sensory procedure, using composition and flow properties as predictor variables. 

scholarly journals Viscosity and Rheological Properties of Graphene Nanopowders Nanofluids

Entropy ◽  
2021 ◽  
Vol 23 (8) ◽  
pp. 979
Author(s):  
Abderrahim Bakak ◽  
Mohamed Lotfi ◽  
Rodolphe Heyd ◽  
Amine Ammar ◽  
Abdelaziz Koumina
Keyword(s):  
Shear Rate ◽  
Rheological Properties ◽  
Dynamic Viscosity ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Heat Extraction ◽  
Rheological Characterization ◽  
Shear Rates ◽  
Rheological Measurements

The dynamic viscosity and rheological properties of two different non-aqueous graphene nano-plates-based nanofluids are experimentally investigated in this paper, focusing on the effects of solid volume fraction and shear rate. For each nanofluid, four solid volume fractions have been considered ranging from 0.1% to 1%. The rheological characterization of the suspensions was performed at 20 ∘C, with shear rates ranging from 10−1s−1 to 103s−1, using a cone-plate rheometer. The Carreau–Yasuda model has been successfully applied to fit most of the rheological measurements. Although it is very common to observe an increase of the viscosity with the solid volume fraction, we still found here that the addition of nanoparticles produces lubrication effects in some cases. Such a result could be very helpful in the domain of heat extraction applications. The dependence of dynamic viscosity with graphene volume fraction was analyzed using the model of Vallejo et al.

Sign in / Sign up

Export Citation Format

Share Document