scholarly journals The suppression of hydrodynamic noise from underwater sonar domes by flow control

2019 ◽  
Vol 283 ◽  
pp. 08008
Author(s):  
Jie Pei ◽  
Chen Niu ◽  
Junchao Qu ◽  
Yongwei Liu ◽  
Dejiang Shang
Keyword(s):  
Boundary Layer ◽  
Leading Edge ◽  
Underwater Vehicles ◽  
Noise Sources ◽  
Outer Flow ◽  
Cavitation Phenomenon ◽  
Flow Fluctuation ◽  
Hydrodynamic Noise ◽  
High Level ◽  
Transition Areas

Hydrodynamic noise is one of the three major noise sources of underwater vehicles. The sonar dome is a device placed in front of the ship and the submarine to absorb the flow fluctuation and to reduce the hydrodynamic noise, so that the sonar inside the dome is not affected by the external fluid. However, with the increase of the velocity of ships and submarines, cavitation can usually form in the bulge of the sonar domes, which will bring high level of noise to the sonar. The internal self-noise of the sonar dome mainly comes from two areas: the leading-edge stagnation point and the transition zone of boundary layer. In the paper, we designed the leading-edge serrations and dimples in the leading-edge and transition areas of the sonar dome respectively to reduce the movement resistance and prevent the separation of the boundary layer. The research on leading-edge serrations and dimple technology is carried out by using theoretical analysis, numerical calculations. The results show that the leading-edge serrations and dimples can add energy from the outer flow into the boundary layer; the cavitation phenomenon can be delayed. The hydrodynamic noise has been suppressed by about 20dB.

Boundary layer development after a separated region

1998 ◽  
Vol 374 ◽  
pp. 91-116 ◽  
Author(s):  
IAN P. CASTRO ◽  
ELEANORA EPIK
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Free Stream ◽  
Turbulence Models ◽  
Separated Flow ◽  
Leading Edge ◽  
Turbulence Structure ◽  
Outer Flow ◽  
Free Stream Turbulence ◽  
Layer Region

Measurements obtained in boundary layers developing downstream of the highly turbulent, separated flow generated at the leading edge of a blunt flat plate are presented. Two cases are considered: first, when there is only very low (wind tunnel) turbulence present in the free-stream flow and, second, when roughly isotropic, homogeneous turbulence is introduced. With conditions adjusted to ensure that the separated region was of the same length in both cases, the flow around reattachment was significantly different and subsequent differences in the development rate of the two boundary layers are identified. The paper complements, but is much more extensive than, the earlier presentation of some of the basic data (Castro & Epik 1996), confirming not only that the development process is very slow, but also that it is non-monotonic. Turbulence stress levels fall below those typical of zero-pressure-gradient boundary layers and, in many ways, the boundary layer has features similar to those found in standard boundary layers perturbed by free-stream turbulence. It is argued that, at least as far as the turbulence structure is concerned, the inner layer region develops no more quickly than does the outer flow and it is the latter which essentially determines the overall rate of development of the whole flow. Some numerical computations are used to assess the extent to which current turbulence models are adequate for such flows.

Study on Vortex Generators for Control of Attached Cavitation

2017 ◽  
Author(s):  
Bangxiang Che ◽  
Dazhuan Wu
Keyword(s):  
Boundary Layer ◽  
Leading Edge ◽  
Boundary Layer Separation ◽  
Main Flow ◽  
Vortex Generators ◽  
Streamwise Vortices ◽  
Fluid Machinery ◽  
Cavitation Inception ◽  
Sheet Cavitation ◽  
Cavitation Phenomenon

Attached cavitation is a type of common cavitation phenomenon in fluid machinery. It is important to develop methods to control its generation. From the view of cavitation inception, the generation of attached cavitation is greatly influenced by the separated boundary layer upstream of cavitation detachment. In this research, a row of microscopic delta-shaped counter-rotating vortex generators (VGs) was applied on the leading edge of the NACA0015 hydrofoil in order to suppress the boundary layer separation and then suppress the generation of attached cavitation. The application of VGs fixed the position of cavitation inception on hydrofoil thus the sheet cavitation became more stable and the cloud cavity shed from hydrofoil with trim trailing edge more regularly. It was found that cavitation inception always appeared adjacent to VGs due to the low pressure in the corner of streamwise vortices induced by VGs. Hydrofoil with VGs showed an entirely different cavitation morphology on the leading edge. A row of separate microscopic vortex cavitation was induced by the counter-rotating vortices firstly. With the lower the height of VGs, the longer the length of these vortex cavitation due to the weaker interaction between vortices and main flow. Following the vortex cavitation, the attached cavitation was developing, but without typical “finger” structure anymore.

Wind Tunnel Aeroacoustic Tests of Six Airfoils for Use on Small Wind Turbines*

2004 ◽  
Vol 126 (4) ◽  
pp. 974-985 ◽  
Author(s):  
Paul Migliore ◽  
Stefan Oerlemans
Keyword(s):  
Boundary Layer ◽  
Wind Tunnel ◽  
Wind Turbines ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Noise Sources ◽  
Low Reynolds Numbers ◽  
Trailing Edge Noise ◽  
Small Wind Turbines ◽  
Inflow Turbulence

Aeroacoustic tests of seven airfoils were performed in an open jet anechoic wind tunnel. Six of the airfoils are candidates for use on small wind turbines operating at low Reynolds numbers. One airfoil was tested for comparison to benchmark data. Tests were conducted with and without boundary layer tripping. In some cases, a turbulence grid was placed upstream in the test section to investigate inflow turbulence noise. An array of 48 microphones was used to locate noise sources and separate airfoil noise from extraneous tunnel noise. Trailing-edge noise was dominant for all airfoils in clean tunnel flow. With the boundary layer untripped, several airfoils exhibited pure tones that disappeared after proper tripping was applied. In the presence of inflow turbulence, leading-edge noise was dominant for all airfoils.

scholarly journals The Hydrodynamic Noise Suppression of a Scaled Submarine Model by Leading-Edge Serrations

2019 ◽  
Vol 7 (3) ◽  
pp. 68 ◽  
Author(s):  
Yongwei Liu ◽  
Yalin Li ◽  
Dejiang Shang
Keyword(s):  
Noise Reduction ◽  
Experimental Test ◽  
Noise Suppression ◽  
Leading Edge ◽  
Adverse Pressure Gradient ◽  
Horseshoe Vortex ◽  
Underwater Vehicles ◽  
Counter Rotation ◽  
Hydrodynamic Noise ◽  
High Reynolds

High hydrodynamic noise is a threat to the survival of underwater vehicles. We investigated a noise suppression mechanism by putting leading-edge serrations on the sail hull of a scaled SUBOFF model, through numerical calculation and an experimental test. We found that the cone shape of leading-edge serrations can decrease the intensity of the adverse pressure gradient and produce counter-rotation vortices, which destroy the formation of the horseshoe vortex and delay the tail vortex. To achieve the optimum hydrodynamic noise reduction, we summarized the parameters of leading-edge serrations. Then, two steel models were built, according to the simulation. We measured the hydrodynamic noise based on the reverberation method in a gravity water tunnel. The numerically calculated results were validated by the experimental test. The results show that leading-edge serrations with amplitudes of 0.025c and wavelengths of 0.05h can obtain hydrodynamic noise reduction of at least 6 dB, from 10 Hz to 2 kHz, where c is the chord length and h is the height of the sail hull. The results in our study suggest a new way to design underwater vehicles with low hydrodynamic noise at a high Reynolds number.

INFLUENCE OF THE PLATE LEADING-EDGE SHAPE AND THICKNESS ON THE BOUNDARY LAYER LAMINAR-TURBULENT TRANSITION IN HYPERSONIC FLOW

2019 ◽  
Vol 50 (5) ◽  
pp. 461-481
Author(s):  
Sergei Vasilyevich Aleksandrov ◽  
Evgeniya Andreevna Aleksandrova ◽  
Volf Ya. Borovoy ◽  
Andrey Vyacheslavovich Gubernatenko ◽  
Vladimir Evguenyevich Mosharov ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Hypersonic Flow ◽  
Leading Edge ◽  
Turbulent Transition ◽  
Laminar Turbulent Transition

Characteristics of a separated flow past a semicircular leading-edge airfoil model under different imposed pressure gradient

2021 ◽  
pp. 095441002110212
Author(s):  
K Anand ◽  
KT Ganesh
Keyword(s):  
Boundary Layer ◽  
Particle Image Velocimetry ◽  
Pressure Gradient ◽  
Particle Image ◽  
Separation Bubble ◽  
Separated Flow ◽  
Leading Edge ◽  
Field Measurements ◽  
Bench Mark ◽  
Image Velocimetry

The effect of pressure gradient on a separated boundary layer past the leading edge of an airfoil model is studied experimentally using electronically scanned pressure (ESP) and particle image velocimetry (PIV) for a Reynolds number ( Re) of 25,000, based on leading-edge diameter ( D). The features of the boundary layer in the region of separation and its development past the reattachment location are examined for three cases of β (−30°, 0°, and +30°). The bubble parameters such as the onset of separation and transition and the reattachment location are identified from the averaged data obtained from pressure and velocity measurements. Surface pressure measurements obtained from ESP show a surge in wall static pressure for β = −30° (flap deflected up), while it goes down for β = +30° (flap deflected down) compared to the fundamental case, β = 0°. Particle image velocimetry results show that the roll up of the shear layer past the onset of separation is early for β = +30°, owing to higher amplification of background disturbances compared to β = 0° and −30°. Downstream to transition location, the instantaneous field measurements reveal a stretched, disoriented, and at instances bigger vortices for β = +30°, whereas a regular, periodically shed vortices, keeping their identity past the reattachment location, is observed for β = 0° and −30°. Above all, this study presents a new insight on the features of a separation bubble receiving a disturbance from the downstream end of the model, and these results may serve as a bench mark for future studies over an airfoil under similar environment.

Experimental study of heat transfer in the boundary layer of a flat plate with the impact of weak shock waves on the leading edge

2020 ◽  
Author(s):  
V. L. Kocharin ◽  
A. A. Yatskikh ◽  
D. S. Prishchepova ◽  
A. V. Panina ◽  
Yu. G. Yermolaev ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Experimental Study ◽  
Shock Waves ◽  
Flat Plate ◽  
Leading Edge ◽  
Weak Shock ◽  
The Impact

scholarly journals Effects of Tip Leakage Flow on the Aerodynamic Performance and Stability of an Axial-Flow Transonic Compressor Stage

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4168
Author(s):  
Botao Zhang ◽  
Xiaochen Mao ◽  
Xiaoxiong Wu ◽  
Bo Liu
Keyword(s):  
Boundary Layer ◽  
Shock Wave ◽  
Axial Flow ◽  
Leading Edge ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Transonic Compressor

To explain the effect of tip leakage flow on the performance of an axial-flow transonic compressor, the compressors with different rotor tip clearances were studied numerically. The results show that as the rotor tip clearance increases, the leakage flow intensity is increased, the shock wave position is moved backward, and the interaction between the tip leakage vortex and shock wave is intensified, while that between the boundary layer and shock wave is weakened. Most of all, the stall mechanisms of the compressors with varying rotor tip clearances are different. The clearance leakage flow is the main cause of the rotating stall under large rotor tip clearance. However, the stall form for the compressor with half of the designed tip clearance is caused by the joint action of the rotor tip stall caused by the leakage flow spillage at the blade leading edge and the whole blade span stall caused by the separation of the boundary layer of the rotor and the stator passage. Within the investigated varied range, when the rotor tip clearance size is half of the design, the compressor performance is improved best, and the peak efficiency and stall margin are increased by 0.2% and 3.5%, respectively.

scholarly journals Leading Edge Blowing to Mimic and Enhance the Serration Effects for Aerofoil

2021 ◽  
Vol 11 (6) ◽  
pp. 2593
Author(s):  
Yasir Al-Okbi ◽  
Tze Pei Chong ◽  
Oksana Stalnov
Keyword(s):  
Boundary Layer ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Boundary Layer Separation ◽  
Shear Instability ◽  
Vortical Flow ◽  
High Angle ◽  
High Angle Of Attack ◽  
Layer Separation ◽  
Aerodynamic Performances

Leading edge serration is now a well-established and effective passive control device for the reduction of turbulence–leading edge interaction noise, and for the suppression of boundary layer separation at high angle of attack. It is envisaged that leading edge blowing could produce the same mechanisms as those produced by a serrated leading edge to enhance the aeroacoustics and aerodynamic performances of aerofoil. Aeroacoustically, injection of mass airflow from the leading edge (against the incoming turbulent flow) can be an effective mechanism to decrease the turbulence intensity, and/or alter the stagnation point. According to classical theory on the aerofoil leading edge noise, there is a potential for the leading edge blowing to reduce the level of turbulence–leading edge interaction noise radiation. Aerodynamically, after the mixing between the injected air and the incoming flow, a shear instability is likely to be triggered owing to the different flow directions. The resulting vortical flow will then propagate along the main flow direction across the aerofoil surface. These vortical flows generated indirectly owing to the leading edge blowing could also be effective to mitigate boundary layer separation at high angle of attack. The objectives of this paper are to validate these hypotheses, and combine the serration and blowing together on the leading edge to harvest further improvement on the aeroacoustics and aerodynamic performances. Results presented in this paper strongly indicate that leading edge blowing, which is an active flow control method, can indeed mimic and even enhance the bio-inspired leading edge serration effectively.

Swept wing boundary-layer receptivity to localized surface roughness

2012 ◽  
Vol 711 ◽  
pp. 516-544 ◽  
Author(s):  
David Tempelmann ◽  
Lars-Uve Schrader ◽  
Ardeshir Hanifi ◽  
Luca Brandt ◽  
Dan S. Henningson
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Practical Interest ◽  
Leading Edge ◽  
Constant Factor ◽  
Computationally Efficient ◽  
Swept Wing ◽  
Predictive Tool ◽  
Free Stream Turbulence ◽  
Streamwise Location

AbstractThe receptivity to localized surface roughness of a swept-wing boundary layer is studied by direct numerical simulation (DNS) and computations using the parabolized stability equations (PSEs). The DNS is laid out to reproduce wind tunnel experiments performed by Saric and coworkers, where micron-sized cylinders were used to trigger steady crossflow modes. The amplitudes of the roughness-induced fundamental crossflow wave and its superharmonics obtained from nonlinear PSE solutions agree excellently with the DNS results. A receptivity model using the direct and adjoint PSEs is shown to provide reliable predictions of the receptivity to roughness cylinders of different heights and chordwise locations. Being robust and computationally efficient, the model is well suited as a predictive tool of receptivity in flows of practical interest. The crossflow mode amplitudes obtained based on both DNS and PSE methods are 40 % of those measured in the experiments. Additional comparisons between experimental and PSE data for various disturbance wavelengths reveal that the measured disturbance amplitudes are consistently larger than those predicted by the PSE-based receptivity model by a nearly constant factor. Supplementary DNS and PSE computations suggest that possible natural leading-edge roughness and free-stream turbulence in the experiments are unlikely to account for this discrepancy. It is more likely that experimental uncertainties in the streamwise location of the roughness array and cylinder height are responsible for the additional receptivity observed in the experiments.

Sign in / Sign up

Export Citation Format

Share Document