scholarly journals The Degradation of Epoxy Resin-Coated ZnO Varistors at Elevated Temperatures and Ambient Humidity Conditions

2003 ◽  
Vol 26 (4) ◽  
pp. 235-243 ◽  
Author(s):  
Jianying Li ◽  
Shengtao Li ◽  
M. A. Alim ◽  
G. Chen
Keyword(s):  
Epoxy Resin ◽  
Leakage Current ◽  
Elevated Temperatures ◽  
Ambient Pressure ◽  
Degradation Process ◽  
Experimental Conditions ◽  
Initial Current ◽  
Ambient Humidity ◽  
Zno Varistors ◽  
Excellent Property

The degradation of the epoxy resin-coated commercial ZnO varistors at elevated temperatures and ambient humid conditions has been investigated experimentally. It has been observed that the leakage current of the ZnO varistors increases under the voltage stress at elevated temperatures with ambient humidity content. The change in the leakage current corresponding to a fixed electric field with respect to the initial current is taken as the dimensionless degradation index. This index is monitored at various experimental conditions in conjunction with the curing condition of the epoxy resin powder. The results are carefully evaluated, and it has been found that the diffusion process of the moisture into the ZnO varistors plays a key role in the degradation process provided that these varistors had excellent property to begin with. The ionisation of the moisture at the interface between the ZnO block and the epoxy resin coating leads to the increase of the leakage current. Furthermore, the role of the ambient pressure corresponding to the elevated temperatures is considered as the variable to the degradation process. These data are also monitored and analysed as a function of time.

scholarly journals Blind Deblurring Based on Sigmoid Function

Sensors ◽  
2021 ◽  
Vol 21 (10) ◽  
pp. 3484
Author(s):  
Shuhan Sun ◽  
Lizhen Duan ◽  
Zhiyong Xu ◽  
Jianlin Zhang
Keyword(s):  
Performance Optimization ◽  
Degradation Process ◽  
Image Deconvolution ◽  
Sigmoid Function ◽  
Blind Image Deblurring ◽  
Linear Estimators ◽  
Blind Deblurring ◽  
Degraded Image ◽  
Excellent Property ◽  
Blind Image

Blind image deblurring, also known as blind image deconvolution, is a long-standing challenge in the field of image processing and low-level vision. To restore a clear version of a severely degraded image, this paper proposes a blind deblurring algorithm based on the sigmoid function, which constructs novel blind deblurring estimators for both the original image and the degradation process by exploring the excellent property of sigmoid function and considering image derivative constraints. Owing to these symmetric and non-linear estimators of low computation complexity, high-quality images can be obtained by the algorithm. The algorithm is also extended to image sequences. The sigmoid function enables the proposed algorithm to achieve state-of-the-art performance in various scenarios, including natural, text, face, and low-illumination images. Furthermore, the method can be extended naturally to non-uniform deblurring. Quantitative and qualitative experimental evaluations indicate that the algorithm can remove the blur effect and improve the image quality of actual and simulated images. Finally, the use of sigmoid function provides a new approach to algorithm performance optimization in the field of image restoration.

scholarly journals Photocatalytic Treatment of Wastewater Containing Simultaneous Organic and Inorganic Pollution: Competition and Operating Parameters Effects

Catalysts ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 855
Author(s):  
Ahmed Amine Azzaz ◽  
Salah Jellali ◽  
Nasser Ben Harharah Hamed ◽  
Atef El Jery ◽  
Lotfi Khezami ◽  
...  
Keyword(s):  
Ultra Violet ◽  
Degradation Process ◽  
Molar Ratio ◽  
Experimental Conditions ◽  
Retention Capacity ◽  
Isotherm Study ◽  
Related Data ◽  
Ph Values ◽  
Pseudo Second Order ◽  
Maximum Retention

In the present study, methylene blue (MB) removal from aqueous solutions via the photocatalytic process using TiO2 as a catalyst in the presence of external ultra-violet light (UV) was investigated. The results of adsorption in the absence of UV radiation showed that adsorption reached an equilibrium state at 60 min. The experimental kinetic data were found to be well fitted by the pseudo-second-order model. Furthermore, the isotherm study suggested that dye uptake by TiO2 is a chemisorption process with a maximum retention capacity of 34.0 mg/g. The photodegradation of MB was then assessed under various experimental conditions. The related data showed that dye mineralization decreased when dye concentrations were increased and was favored at high pH values and low salt concentrations. The simultaneous presence of organic and inorganic pollution (Zinc) was also evaluated. The effect of the molar ratio Zn2+/MB+ in the solution at different pH values and NaCl concentrations was also monitored. The corresponding experimental results showed that at low values of Zn2+ in the solution (30 mg/L), the kinetic of the MB removal became faster until reaching an optimum at Zn2+/MB+ concentrations of 60/60 mg/L; it then slowed down for higher concentrations. The solutions’ carbon contents were measured during the degradation process and showed total mineralization after about 5 h for the optimal Zn2+/MB+ condition.

scholarly journals Synthesis, Analysis, and Testing of BiOBr-Bi2WO6Photocatalytic Heterojunction Semiconductors

2015 ◽  
Vol 2015 ◽  
pp. 1-12 ◽  
Author(s):  
Xiangchao Meng ◽  
Zisheng Zhang
Keyword(s):  
Visible Light ◽  
Visible Light Irradiation ◽  
Degradation Process ◽  
Light Irradiation ◽  
Enhancement Effect ◽  
Electron Hole ◽  
Experimental Conditions ◽  
Synthesis Conditions ◽  
Optimum Synthesis ◽  
Photocatalytic Activities

In photocatalysis, the recombination of electron-hole pairs is generally regarded as one of its most serious drawbacks. The synthesis of various composites with heterojunction structures has increasingly shed light on preventing this recombination. In this work, a BiOBr-Bi2WO6photocatalytic heterojunction semiconductor was synthesized by the facile hydrothermal method and applied in the photocatalytic degradation process. It was determined that both reaction time and temperature significantly affected the crystal structure and morphologies of the photocatalysts. BiOBr (50 at%)-Bi2WO6composites were prepared under optimum synthesis conditions (120°C for 6 h) and by theoretically analyzing the DRS results, it was determined that they possessed the suitable band gap (2.61 eV) to be stimulated by visible-light irradiation. The photocatalytic activities of the as-prepared photocatalysts were evaluated by the degradation ofRhodamine B (RhB)under visible-light irradiation. The experimental conditions, including initial concentration, pH, and catalyst dosage, were explored and the photocatalysts in this system were proven stable enough to be reused for several runs. Moreover, the interpreted mechanism of the heterojunction enhancement effect proved that the synthesis of a heterojunction structure provided an effective method to decrease the recombination rate of the electron-hole pairs, thereby improving the photocatalytic activity.

scholarly journals Temperature uniformity in the CERN CLOUD chamber

2017 ◽  
Vol 10 (12) ◽  
pp. 5075-5088 ◽  
Author(s):  
António Dias ◽  
Sebastian Ehrhart ◽  
Alexander Vogel ◽  
Christina Williamson ◽  
João Almeida ◽  
...  
Keyword(s):  
Steady State ◽  
Air Temperature ◽  
Elevated Temperatures ◽  
Trace Gases ◽  
Vertical Direction ◽  
Cloud Chamber ◽  
Temperature Uniformity ◽  
Atmospheric Conditions ◽  
Cloud Droplets ◽  
Experimental Conditions

Abstract. The CLOUD (Cosmics Leaving OUtdoor Droplets) experiment at CERN (European Council for Nuclear Research) investigates the nucleation and growth of aerosol particles under atmospheric conditions and their activation into cloud droplets. A key feature of the CLOUD experiment is precise control of the experimental parameters. Temperature uniformity and stability in the chamber are important since many of the processes under study are sensitive to temperature and also to contaminants that can be released from the stainless steel walls by upward temperature fluctuations. The air enclosed within the 26 m3 CLOUD chamber is equipped with several arrays (strings) of high precision, fast-response thermometers to measure its temperature. Here we present a study of the air temperature uniformity inside the CLOUD chamber under various experimental conditions. Measurements were performed under calibration conditions and run conditions, which are distinguished by the flow rate of fresh air and trace gases entering the chamber at 20 and up to 210 L min−1, respectively. During steady-state calibration runs between −70 and +20 °C, the air temperature uniformity is better than ±0.06 °C in the radial direction and ±0.1 °C in the vertical direction. Larger non-uniformities are present during experimental runs, depending on the temperature control of the make-up air and trace gases (since some trace gases require elevated temperatures until injection into the chamber). The temperature stability is ±0.04 °C over periods of several hours during either calibration or steady-state run conditions. During rapid adiabatic expansions to activate cloud droplets and ice particles, the chamber walls are up to 10 °C warmer than the enclosed air. This results in temperature differences of ±1.5 °C in the vertical direction and ±1 °C in the horizontal direction, while the air returns to its equilibrium temperature with a time constant of about 200 s.

scholarly journals Phenol Novalac Epoxy-modified unsaturated polyester hybrid networks by Silica Nanoparticles/ and Cross linking with Silane Compounds

2020 ◽  
Vol 1 (2) ◽  
pp. 28-32
Keyword(s):  
Epoxy Resin ◽  
Silica Nanoparticles ◽  
Elevated Temperatures ◽  
Unsaturated Polyester ◽  
Low Cost ◽  
Physical And Mechanical Properties ◽  
Hybrid Networks ◽  
Azo Compounds ◽  
Cross Linking ◽  
Chemical Attributes

In this study epoxy phenol novalac resin which consists of silica nanoparticles and unsaturated poly ester resin linked to the Silane and cross linking to that structure and also parameters affecting the processes involved have been evaluated. Cross linking in phenol novalac epoxy resins effects on many properties such as thermal, electrical, mechanical and chemical attributes especially in elevated temperatures. Silane cross-linking’s in phenol novalac epoxy resin with respect to other methods like proxiding, irradiation and utilization of Azo compounds, looks to be a very simple and low cost route, which makes it very encouraging for various industries. Unsaturated poly ester resin is compatible with phenol novalac epoxy resin and also creates some cross-linking and as far as tri methoxy Silane is added to the mentioned resin, its thermal, physical and mechanical properties are optimized. In this literature impact, tension, glass transition temperature, humidity absorption, FTIR and Scanning electron microscopy (SEM) tests were done and the results revealed that as the cross-linking occurs, tension in rupture region increases. This increase is more common at elevated temperatures. The growth in content of silica nanoparticles leads to a drop in water permeability of phenol novalac epoxy resin nanocomposite which contains unsaturated poly ester resin.

scholarly journals Prospects for the expansion of standing wave ambient pressure photoemission spectroscopy to reactions at elevated temperatures

2022 ◽  
Vol 40 (1) ◽  
pp. 013207
Author(s):  
Osman Karslıoğlu ◽  
Lena Trotochaud ◽  
Farhad Salmassi ◽  
Eric M. Gullikson ◽  
Andrey Shavorskiy ◽  
...  
Keyword(s):  
Standing Wave ◽  
Elevated Temperatures ◽  
Ambient Pressure ◽  
Photoemission Spectroscopy

Functionalization of Graphene with O and S for Catalytic Degradation of Chlorophenols and Dyes

2021 ◽  
Vol 1019 ◽  
pp. 194-204
Author(s):  
S. Sudhaparimala ◽  
R. Usha
Keyword(s):  
Graphene Oxide ◽  
Organic Dyes ◽  
Analytical Techniques ◽  
Degradation Process ◽  
Experimental Conditions ◽  
Photocatalytic Application ◽  
Wide Range ◽  
Doped Graphene ◽  
The Given ◽  
Graphene Structures

Graphene, functionalized with the heteroatoms like nitrogen, oxygen and sulphur atoms has been well explored for a wide range of applications but only few reports are available on its adsorption and photocatalytic application in the degradation of chlorophenols and organic dyes. A simple and energy-efficient process to prepare graphene oxide and sulphur doped graphene oxide was developed. The micro structure and surface morphology were confirmed by the analytical techniques of Powder X-ray diffractogram (PXRD), Fourier Transformed Raman Spectroscopy (FT-Raman), Scanning Electron Microscopy. The results were suggestive of the structures suitable for screening their catalytic activity in the degradation of the highly toxic polychlorophenols and organic dyes. The adsorption and photo catalytic properties of the asprepared samples were screened for the degradation process and it was found that sulphur doped graphene oxide showed more positive results for the degradation of chlorophenols than graphene oxide. Under the given experimental conditions the decoloration of dyes were not satisfactory. Ultimately, the study provided an economical and efficient, method for tuning graphene structures for the removal of pollutants in wastewater.

High-Temperature Trench Capacitors, Using Thin-Film ALD Dielectrics

2015 ◽  
Vol 2015 (HiTEN) ◽  
pp. 000130-000133 ◽  
Author(s):  
Dorothee Dietz ◽  
Yusuf Celik ◽  
Andreas Goehlich ◽  
Holger Vogt ◽  
Holger Kappert
Keyword(s):  
High Temperature ◽  
Leakage Current ◽  
Automobile Industry ◽  
Elevated Temperatures ◽  
Atomic Layer ◽  
Operating Voltage ◽  
Low Leakage ◽  
Low Leakage Current ◽  
Layer Deposition ◽  
Soft Breakdown

High-temperature passive electronic becomes more and more important, e.g. in the field of deep drilling, aerospace or in automobile industry. For these applications, capacitors are needed, which are able to withstand temperatures up to 300 °C, which exhibit a low leakage current at elevated temperatures, a breakdown voltage above the intended operating voltage and a high capacitive density value. In this paper, investigations of 3D-integration and atomic layer deposition (ALD) techniques to achieve these features are presented. A highly n-doped Si-substrate acts as a bottom electrode. Medium- and high-k dielectrics represent the insulator and the upper electrode consists of Ru, TiN or TiAlCN. The materials can be used at elevated temperatures. At room temperature, the leakage current is less than 10 pA/mm2 without showing a soft-breakdown up to ± 15 V, indicating the absence of Fowler-Nordheim tunneling. At 300 °C and at 3 V the leakage current amounts about 1 nA/mm2 and at 5 V a soft-breakdown is detected.

Sign in / Sign up

Export Citation Format

Share Document