scholarly journals Plasma diagnostics during deposition of Zr-B-N coatings by magnetron sputtering of UHTC ceramic in DCMS and HIPIMS modes

2021 ◽  
Vol 2064 (1) ◽  
pp. 012062
Author(s):  
A D Sytchenko ◽  
Ph V Kiryukhantsev-Korneev
Keyword(s):  
Growth Rate ◽  
Magnetron Sputtering ◽  
Metal Ions ◽  
Growth Rates ◽  
Plasma Diagnostics ◽  
Structural Characteristics ◽  
Argon Plasma

Abstract In this work, plasma diagnostics during the deposition of Zr-B-N coatings by DCMS and HIPIMS methods were carried out, the structural characteristics and growth rates of the obtained coatings were investigated; the regularities of the influence of the working atmosphere on the composition of the plasma, as well as on the thickness and growth rate of the coatings are revealed. It was found that the introduction of nitrogen leads to a decrease in the concentration of Zr and B ions in the plasma, as a result of which the growth rate of the coatings decreases. Note that, when using the DCMS method, predominantly argon plasma is observed, while with HIPIMS, the plasma is characterized by a large number of metal ions.

Comparison of copper sulphate pentahydrate growth rates determined by different methods

1990 ◽  
Vol 55 (7) ◽  
pp. 1691-1707 ◽  
Author(s):  
Miloslav Karel ◽  
Jiří Hostomský ◽  
Jaroslav Nývlt ◽  
Axel König
Keyword(s):  
Growth Rate ◽  
Crystal Growth ◽  
Fluidized Bed ◽  
Growth Rates ◽  
Copper Sulphate ◽  
Crystal Growth Rate ◽  
Effect Of Temperature ◽  
Rotating Disc ◽  
Shape Factors ◽  
Data Treatment

Crystal growth rates of copper sulphate pentahydrate (CuSO4.5 H2O) determined by different authors and methods are compared. The methods included in this comparison are: (i) Measurement on a fixed crystal suspended in a streaming solution, (ii) measurement on a rotating disc, (iii) measurement in a fluidized bed, (iv) measurement in an agitated suspension. The comparison involves critical estimation of the supersaturation used in measurements, of shape factors used for data treatment and a correction for the effect of temperature. Conclusions are drawn for the choice of values to be specified when data of crystal growth rate measurements are published.

Measurement of growth rates for single crystals and pressed tablets of CuSO4.5 H2O on a rotating disc

1989 ◽  
Vol 54 (11) ◽  
pp. 2951-2961 ◽  
Author(s):  
Miloslav Karel ◽  
Jaroslav Nývlt
Keyword(s):  
Growth Rate ◽  
Single Crystal ◽  
Single Crystals ◽  
Growth Rates ◽  
Diffusion Coefficients ◽  
Preferred Orientation ◽  
Rotating Disc ◽  
Dissolution Rates ◽  
Rates Of Growth ◽  
Good Agreement

Measured growth and dissolution rates of single crystals and tablets were used to calculate the overall linear rates of growth and dissolution of CuSO4.5 H2O crystals. The growth rate for the tablet is by 20% higher than that calculated for the single crystal. It has been concluded that this difference is due to a preferred orientation of crystal faces on the tablet surface. Calculated diffusion coefficients and thicknesses of the diffusion and hydrodynamic layers in the vicinity of the growing or dissolving crystal are in good agreement with published values.

scholarly journals Accuracy of State-Level Surveillance during Emerging Outbreaks of Respiratory Viruses: A Model-Based Assessment

2021 ◽  
pp. 0272989X2110222
Author(s):  
Yuwen Gu ◽  
Elise DeDoncker ◽  
Richard VanEnk ◽  
Rajib Paul ◽  
Susan Peters ◽  
...  
Keyword(s):  
Growth Rate ◽  
Data Collection ◽  
Disease Progression ◽  
Health Care Providers ◽  
Growth Rates ◽  
State Level ◽  
Future Research ◽  
Care Providers ◽  
State Surveillance ◽  
First Come First Serve

It is long perceived that the more data collection, the more knowledge emerges about the real disease progression. During emergencies like the H1N1 and the severe acute respiratory syndrome coronavirus 2 pandemics, public health surveillance requested increased testing to address the exacerbated demand. However, it is currently unknown how accurately surveillance portrays disease progression through incidence and confirmed case trends. State surveillance, unlike commercial testing, can process specimens based on the upcoming demand (e.g., with testing restrictions). Hence, proper assessment of accuracy may lead to improvements for a robust infrastructure. Using the H1N1 pandemic experience, we developed a simulation that models the true unobserved influenza incidence trend in the State of Michigan, as well as trends observed at different data collection points of the surveillance system. We calculated the growth rate, or speed at which each trend increases during the pandemic growth phase, and we performed statistical experiments to assess the biases (or differences) between growth rates of unobserved and observed trends. We highlight the following results: 1) emergency-driven high-risk perception increases reporting, which leads to reduction of biases in the growth rates; 2) the best predicted growth rates are those estimated from the trend of specimens submitted to the surveillance point that receives reports from a variety of health care providers; and 3) under several criteria to queue specimens for viral subtyping with limited capacity, the best-performing criterion was to queue first-come, first-serve restricted to specimens with higher hospitalization risk. Under this criterion, the lab released capacity to subtype specimens for each day in the trend, which reduced the growth rate bias the most compared to other queuing criteria. Future research should investigate additional restrictions to the queue.

scholarly journals Effect of Voltage Pulse Width and Synchronized Substrate Bias in High-Power Impulse Magnetron Sputtering of Zirconium Films

Coatings ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 7
Author(s):  
Chin-Chiuan Kuo ◽  
Chun-Hui Lin ◽  
Jing-Tang Chang ◽  
Yu-Tse Lin
Keyword(s):  
Growth Rate ◽  
Magnetron Sputtering ◽  
High Power ◽  
Pulse Width ◽  
Film Growth ◽  
Highly Charged Ions ◽  
Argon Pressure ◽  
Hexagonal Prism ◽  
Film Growth Rate ◽  
Charged Ions

The Zr film microstructure is highly influenced by the energy of the plasma species during the deposition process. The influences of the discharge pulse width, which is the key factor affecting ionization of sputtered species in the high-power impulse magnetron sputtering (HiPIMS) process, on the obtained microstructure of films is investigated in this research. The films deposited at different argon pressure and substrate biasing are compared. With keeping the same average HiPIMS power and duty cycle, the film growth rate of the Zr film decreases with increasing argon pressure and enhancing substrate biasing. In addition, the film growth rate decreases with the elongating HiPIMS pulse width. For the deposition at 1.2 Pa argon, extending the pulse width not only intensifies the ion flux toward the substrate but also increases the fraction of highly charged ions, which alter the microstructure of films from individual hexagonal prism columns into a tightly connected irregular column. Increasing film density leads to higher hardness. Sufficient synchronized negative substrate biasing and longer pulse width, which supports higher mobility of adatoms, causes the preferred orientation of hexagonal α-phase Zr films from (0 0 0 2) to (1 0 1¯ 1). Unlike the deposition at 1.2 Pa, highly charged ions are also found during the short HiPIMS pulse width at 0.8 Pa argon.

scholarly journals StalGrowth—A Program to Estimate Speleothem Growth Rates and Seasonal Growth Variations

Geosciences ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 187
Author(s):  
Rolf Vieten ◽  
Francisco Hernandez
Keyword(s):  
Growth Rate ◽  
Growth Rates ◽  
Environmental Parameters ◽  
Ion Concentration ◽  
Radiometric Dating ◽  
Seasonal Growth ◽  
Climate Signal ◽  
Show Evidence ◽  
Cave Monitoring ◽  
Calcium Ion Concentration

Speleothems are one of the few archives which allow us to reconstruct the terrestrial paleoclimate and help us to understand the important climate dynamics in inhabited regions of our planet. Their time of growth can be precisely dated by radiometric techniques, but unfortunately seasonal radiometric dating resolution is so far not feasible. Numerous cave environmental monitoring studies show evidence for significant seasonal variations in parameters influencing carbonate deposition (calcium-ion concentration, cave air pCO2, drip rate and temperature). Variations in speleothem deposition rates need to be known in order to correctly decipher the climate signal stored in the speleothem archive. StalGrowth is the first software to quantify growth rates based on cave monitoring results, detect growth seasonality and estimate the seasonal growth bias. It quickly plots the predicted speleothem growth rate together with the influencing cave environmental parameters to identify which parameter(s) cause changes in speleothem growth rate, and it can also identify periods of no growth. This new program has been applied to multiannual cave monitoring studies in Austria, Gibraltar, Puerto Rico and Texas, and it has identified two cases of seasonal varying speleothem growth.

scholarly journals Effect of Light Intensity and Quality on Growth Rate and Composition of Chlorella vulgaris

Plants ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 31 ◽  
Author(s):  
Maria N. Metsoviti ◽  
George Papapolymerou ◽  
Ioannis T. Karapanagiotidis ◽  
Nikolaos Katsoulas
Keyword(s):  
Growth Rate ◽  
Light Intensity ◽  
Chlorella Vulgaris ◽  
Lipid Content ◽  
Growth Rates ◽  
Solar Irradiance ◽  
White Led ◽  
Microalgal Biomass ◽  
Nm Range ◽  
Effect Of Light

In this research, the effect of solar irradiance on Chlorella vulgaris cultivated in open bioreactors under greenhouse conditions was investigated, as well as of ratio of light intensity in the 420–520 nm range to light in the 580–680 nm range (I420–520/I580–680) and of artificial irradiation provided by red and white LED lamps in a closed flat plate laboratory bioreactor on the growth rate and composition. The increase in solar irradiance led to faster growth rates (μexp) of C. vulgaris under both environmental conditions studied in the greenhouse (in June up to 0.33 d−1 and in September up to 0.29 d−1) and higher lipid content in microalgal biomass (in June up to 25.6% and in September up to 24.7%). In the experiments conducted in the closed bioreactor, as the ratio I420–520/I580–680 increased, the specific growth rate and the biomass, protein and lipid productivities increased as well. Additionally, the increase in light intensity with red and white LED lamps resulted in faster growth rates (the μexp increased up to 0.36 d−1) and higher lipid content (up to 22.2%), while the protein, fiber, ash and moisture content remained relatively constant. Overall, the trend in biomass, lipid, and protein productivities as a function of light intensity was similar in the two systems (greenhouse and bioreactor).

A population birth-and-mutation process, I: explicit distributions for the number of mutants in an old culture of bacteria

1974 ◽  
Vol 11 (03) ◽  
pp. 437-444 ◽  
Author(s):  
Benoit Mandelbrot
Keyword(s):  
Growth Rate ◽  
Mutation Rate ◽  
Growth Rates ◽  
Random Variable ◽  
Mutation Process ◽  
Limit Condition ◽  
Rate Of Growth ◽  
Mathematical Techniques ◽  
First Time

Luria and Delbrück (1943) have observed that, in old cultures of bacteria that have mutated at random, the distribution of the number of mutants is extremely long-tailed. In this note, this distribution will be derived (for the first time) exactly and explicitly. The rates of mutation will be allowed to be either positive or infinitesimal, and the rate of growth for mutants will be allowed to be either equal, greater or smaller than for non-mutants. Under the realistic limit condition of a very low mutation rate, the number of mutants is shown to be a stable-Lévy (sometimes called “Pareto Lévy”) random variable, of maximum skewness ß, whose exponent α is essentially the ratio of the growth rates of non-mutants and of mutants. Thus, the probability of the number of mutants exceeding the very large value m is proportional to m –α–1 (a behavior sometimes referred to as “asymptotically Paretian” or “hyperbolic”). The unequal growth rate cases α ≠ 1 are solved for the first time. In the α = 1 case, a result of Lea and Coulson is rederived, interpreted, and generalized. Various paradoxes involving divergent moments that were encountered in earlier approaches are either absent or fully explainable. The mathematical techniques used being standard, they will not be described in detail, so this note will be primarily a collection of results. However, the justification for deriving them lies in their use in biology, and the mathematically unexperienced biologists may be unfamiliar with the tools used. They may wish for more details of calculations, more explanations and Figures. To satisfy their needs, a report available from the author upon request has been prepared. It will be referred to as Part II.

Reassessment of Maximum Growth Rates for C3 and C4 Crops

1978 ◽  
Vol 14 (1) ◽  
pp. 1-5 ◽  
Author(s):  
J. L. Monteith
Keyword(s):  
Growth Rate ◽  
Growth Rates ◽  
Growing Season ◽  
Maximum Growth ◽  
Maximum Growth Rate ◽  
Crop Growth ◽  
Close Inspection ◽  
Similar Difference ◽  
Photosynthetic Efficiencies

SUMMARYFigures for maximum crop growth rates, reviewed by Gifford (1974), suggest that the productivity of C3 and C4 species is almost indistinguishable. However, close inspection of these figures at source and correspondence with several authors revealed a number of errors. When all unreliable figures were discarded, the maximum growth rate for C3 stands fell in the range 34–39 g m−2 d−1 compared with 50–54 g m−2 d−1 for C4 stands. Maximum growth rates averaged over the whole growing season showed a similar difference: 13 g m−2 d−1 for C3 and 22 g m−2 d−1 for C4. These figures correspond to photosynthetic efficiencies of approximately 1·4 and 2·0%.

Tidal excitation of hydromagnetic waves and their damping in the Earth

1994 ◽  
Vol 274 ◽  
pp. 219-241 ◽  
Author(s):  
R. R. Kerswell
Keyword(s):  
Growth Rate ◽  
Growth Rates ◽  
Outer Core ◽  
Decay Rates ◽  
Wave Disturbance ◽  
Instability Mechanism ◽  
The Earth ◽  
Elliptical Instability ◽  
Hydromagnetic Waves

We examine the possibility that the Earth's outer core, as a tidally distorted fluid-filled rotating spheroid, may be the seat of an elliptical instability. The instability mechanism is described within the framework of a simple Earth-like model. The preferred forms of wave disturbance are explored and a likely growth rate supremum deduced. Estimates are made of the Ohmic and viscous decay rates of such hydromagnetic waves in the outer core. Rather than a conclusive disparity of scales, we find that typical elliptical growth rates, Ohmic decay rates and viscous decay rates all have the same order for plausible core fields and core-to-mantle conductivities. This study is all the more timely considering the recent realization that the Earth's precession may also drive similar instabilities at comparable strengths in the outer core.

Sign in / Sign up

Export Citation Format

Share Document