scholarly journals 1D modelling and PID control of helicopter Diesel engine rotational speed in torque changes

2021 ◽  
Vol 2130 (1) ◽  
pp. 012007
Author(s):  
P Magryta
Keyword(s):  
Diesel Engine ◽  
Rotational Speed ◽  
Internal Combustion Engines ◽  
Fuel Injection ◽  
P Element ◽  
Helicopter Rotor ◽  
Maximum Speed ◽  
P Value ◽  
Engine Operation ◽  
Dimensional Simulation

Abstract The article discusses the results of simulation tests concerning the operation of a diesel engine for a light helicopter. The tests were carried out in the AVL Boost software which is used to analyze dynamic phenomena in internal combustion engines. The research object was a newly designed diesel engine of a V8 structure and a power of 330 kW. This engine was designed to be used in the construction of a light class helicopter. The created one-dimensional simulation model included all the main engine components as well as the connection to the helicopter main transmission and the helicopter rotor. The tests consisted in selecting the P value in the PID controller used to control the amount of fuel injected into the engine. The change in the P value indirectly influenced the reaction of the engine to a change in power and torque during horizontal flight of a helicopter. These changes were introduced by changing thrust torque in the helicopter rotor. The fuel injection regulator was designed to maintain a constant engine rotational speed. The maximum speed deviations from the nominal speed of the engine operation due to both increasing and decreasing speed were analyzed. Additionally, the sum of the deviation values was analyzed until the rotational speed of the tested object stabilized. The results showed that the change of the P parameter affects all the analyzed parameters of the engine operation; however, the minimum deviation values for each parameter occur at non-equal PID settings, which makes it difficult to clearly indicate the appropriate value of the P element.

DIESEL ENGINE OPERATION IN USE OF FUEL WITH ADDITIVES

2018 ◽  
pp. 18-24
Author(s):  
Petar Kazakov ◽  
Atanas Iliev ◽  
Emil Marinov
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Experimental Studies ◽  
Combustion Engines ◽  
Engine Operation ◽  
Factors Affecting ◽  
Operating Modes ◽  
Positive Effects

Over the decades, more attention has been paid to emissions from the means of transport and the use of different fuels and combustion fuels for the operation of internal combustion engines than on fuel consumption. This, in turn, enables research into products that are said to reduce fuel consumption. The report summarizes four studies of fuel-related innovation products. The studies covered by this report are conducted with diesel fuel and usually contain diesel fuel and three additives for it. Manufacturers of additives are based on already existing studies showing a 10-30% reduction in fuel consumption. Comparative experimental studies related to the use of commercially available diesel fuel with and without the use of additives have been performed in laboratory conditions. The studies were carried out on a stationary diesel engine СМД-17КН equipped with brake КИ1368В. Repeated results were recorded, but they did not confirm the significant positive effect of additives on specific fuel consumption. In some cases, the factors affecting errors in this type of research on the effectiveness of fuel additives for commercial purposes are considered. The reasons for the positive effects of such use of additives in certain engine operating modes are also clarified.

Measurement of cycle-resolved engine-out soot concentration from a diesel-pilot assisted natural gas direct-injection compression-ignition engine

2021 ◽  
pp. 146808742098626
Author(s):  
Pooyan Kheirkhah ◽  
Patrick Kirchen ◽  
Steven Rogak
Keyword(s):  
Response Time ◽  
Internal Combustion Engines ◽  
Fuel Injection ◽  
Exhaust System ◽  
Cycle Period ◽  
Scanning Mobility Particle Sizer ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Exhaust Port ◽  
Exhaust Stream

Exhaust-stream particulate matter (PM) emission from combustion sources such as internal combustion engines are typically characterized with modest temporal resolutions; however, in-cylinder investigations have demonstrated significant variability and the importance of individual cycles in transient PM emissions. Here, using a Fast Exhaust Nephelometer (FEN), a methodology is developed for measuring the cycle-specific PM concentration at the exhaust port of a single-cylinder research engine. The measured FEN light-scattering is converted to cycle-resolved soot mass concentration ([Formula: see text]), and used to characterize the variability of engine-out soot emission. To validate this method, exhaust-port FEN measurements are compared with diluted gravimetric PM mass and scanning mobility particle sizer (SMPS) measurements, resulting in close agreements with an overall root-mean-square deviation of better than 30%. It is noted that when PM is sampled downstream in the exhaust system, the particles are larger by 50–70 nm due to coagulation. The response time of the FEN was characterized using a “skip-firing” scheme, by enabling and disabling the fuel injection during otherwise steady-state operation. The average response time due to sample transfer and mixing times is 55 ms, well below the engine cycle period (100 ms) for the considered engine speeds, thus suitable for single-cycle measurements carried out in this work. Utilizing the fast-response capability of the FEN, it is observed that cycle-specific gross indicated mean effective pressure (GIMEP) and [Formula: see text] are negatively correlated ([Formula: see text]: 0.2–0.7), implying that cycles with lower GIMEP emit more soot. The physical causes of this association deserve further investigation, but are expected to be caused by local fuel-air mixing effects. The averaged exhaust-port [Formula: see text] is similar to the diluted gravimetric measurements, but the cycle-to-cycle variations can only be detected with the FEN. The methodology developed here will be used in future investigations to characterize PM emissions during transient engine operation, and to enable exhaust-stream PM measurements for optical engine experiments.

Study on Performance Optimization of Car Diesel Engine with VNT Based on One-Dimensional Simulation and Experimental Verification

2012 ◽  
Vol 155-156 ◽  
pp. 12-17 ◽  
Author(s):  
Lian Xu Wang ◽  
Da Wei Qu ◽  
Chang Qing Song ◽  
Ye Tian
Keyword(s):  
Experimental Data ◽  
Diesel Engine ◽  
Performance Optimization ◽  
High Speed ◽  
Turbine Blades ◽  
Simulation Software ◽  
Engine Operation ◽  
One Dimensional ◽  
Distribution Phase ◽  
Dimensional Simulation

To research the performance optimization of high speed car diesel engine，firstly according to the characteristic of car diesel engine with Variable Nozzle Turbocharger (VNT)， one-dimensional cycle model of the engine was established by using simulation software BOOST and validated by experimental data in this paper. The turbine blades’ opening corresponding to different speed was determined. Therefore the problem that the VNT surges at low engine speed and the inlet air flow is insufficient at high speed was solved. Based on the above model, this paper improved the efficiency of the engine by optimizing the compression ratio and the distribution phase of camshaft and then used the experimental data to check the simulation results. Meanwhile the fuel consumption and the possibility of the engine operation roughness decreased.

scholarly journals Performance evaluation of common rail direct injection (CRDI) engine fuelled with Uppage Oil Methyl Ester (UOME)

2015 ◽  
Vol 4 (1) ◽  
pp. 1-10 ◽  
Author(s):  
D.N. Basavarajappa ◽  
N. R. Banapurmath ◽  
S.V. Khandal ◽  
G. Manavendra
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Engines ◽  
High Speed ◽  
Alternative Fuels ◽  
High Pressures ◽  
Fuel Injection ◽  
Injection Timing ◽  
Engine Operation ◽  
Performance And Emission

For economic and social development of any country energy is one of the most essential requirements. Continuously increasing price of crude petroleum fuels in the present days coupled with alarming emissions and stringent emission regulations has led to growing attention towards use of alternative fuels like vegetable oils, alcoholic and gaseous fuels for diesel engine applications. Use of such fuels can ease the burden on the economy by curtailing the fuel imports. Diesel engines are highly efficient and the main problems associated with them is their high smoke and NOx emissions.  Hence there is an urgent need to promote the use of alternative fuels in place of high speed diesel (HSD) as substitute. India has a large agriculture base that can be used as a feed stock to obtain newer fuel which is renewable and sustainable. Accordingly Uppage oil methyl ester (UOME) biodiesel was selected as an alternative fuel. Use of biodiesels in diesel engines fitted with mechanical fuel injection systems has limitation on the injector opening pressure (300 bar). CRDI system can overcome this drawback by injecting fuel at very high pressures (1500-2500 bar) and is most suitable for biodiesel fuels which are high viscous. This paper presents the performance and emission characteristics of a CRDI diesel engine fuelled with UOME biodiesel at different injection timings and injection pressures. From the experimental evidence it was revealed that UOME biodiesel yielded overall better performance with reduced emissions at retarded injection timing of -10° BTDC in CRDI mode of engine operation.

Simulation Model of Four Stroke, Six Cylinder Marine Diesel Engine

2015 ◽  
Vol 236 ◽  
pp. 113-118
Author(s):  
Marcin Kluczyk ◽  
Andrzej Grządziela
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Technical Condition ◽  
Operational Experience ◽  
Fuel System ◽  
Engine Operation ◽  
Injection Pump ◽  
Fuel Injection Pump ◽  
Marine Diesel ◽  
Basic Equations

The paper presents a model of dynamics of six-cylinder inline diesel engine executed in the Matlab software. The basic equations necessary to describe the forces acting during the engine operation was presented. Application of some simplifications allowed to present proposal of a mathematical model of the engine, which allows analysis of changes of forces in the crank-piston system, depending on the technical condition of the fuel system elements. Operational experience indicate that one of the most common cause of failure of the fuel system is reduced fuel charge supplied by a defective fuel injection pump. Calculations of gas forces had been replaced by the implementation into the model indication charts recorded from tests on a engine test stand. Simulation results were presented as a result of FFT spectra of modeled tangential forces.

The General Electric Coal-Fueled Diesel Engine Program (1982–1993): A Technical Review

1994 ◽  
Vol 116 (4) ◽  
pp. 749-757 ◽  
Author(s):  
J. A. Caton ◽  
B. D. Hsu
Keyword(s):  
Diesel Engine ◽  
Research And Development ◽  
Fuel Injection ◽  
Low Cost ◽  
Development Program ◽  
Transportation Systems ◽  
Department Of Energy ◽  
General Electric ◽  
Engine Operation ◽  
Coal Fuel

In the early 1980s, General Electric—Transportation Systems (GE-TS), a manufacturer of locomotive diesel engines, announced plans to develop a coal-fueled locomotive due to the availability and low cost of coal. In 1985 and 1988, the General Electric Company (GE) was awarded major contracts from the Department of Energy, Morgantown Energy Technology Center, to continue the research and development of a coal-fueled diesel engine. This paper is a review of the technical accomplishments and discoveries of the GE coal-fueled diesel engine research and development program during the years 1982–1993. The results of an economic assessment completed by GE-TS indicated the merits for the development of a coal fueled diesel engine for locomotive applications and therefore, GE-TS embarked on an ambitious program to develop and commercialize a coal-fueled diesel engine. Among the major accomplishments of this program were the development of specialized fuel injection equipment for coal–water slurries, diamond compact inserts for the nozzle tips for wear resistance, and an integrated emissions control system. Over 500 hours of engine operation was accumulated using coal fuel during the duration of this program. A major milestone was attained when, during November and December 1991, a coal-fueled diesel engine powered a locomotive on the General Electric test track.

Methodology to Optimize and Predict the Measurement Point Distribution for Compressor Mapping on the Hot-Gas Test Bench

2019 ◽  
Author(s):  
Holger Mai ◽  
André Kaufmann ◽  
Mathias Vogt
Keyword(s):  
Rotational Speed ◽  
Internal Combustion Engines ◽  
Test Bench ◽  
Logical Consequence ◽  
Test System ◽  
Engine Operation ◽  
Point Distribution ◽  
Hot Gas ◽  
Operation Conditions ◽  
Matching Process

Abstract Current and future legal requirements for internal combustion engines (ICE) are increasing the complexity of modern charging systems. Test system manufacturers are facing high demands in terms of hardware specifications and methods for turbocharger testing on a hot-gas test bench. Innovative test systems and methodologies help to improve the quality of the turbocharger and engine matching process and significantly optimize the operating strategy in engine process simulation, especially in the early development and design phase. The compressor and turbine characteristic maps are the most important sources of information in order to quantify the performance of the turbocharger. This is achieved in practice by thermodynamically evaluating turbochargers on the hot-gas test bench under test conditions that are as close as possible to real engine operation conditions. Turbocharger compressor mapping relies on the measurement of pressure and temperature upstream and downstream of the compressor at designated operating points. For use in the turbocharger matching process, mostly equidistant points on the operation line between surge and choke are required. Comparison to Computational Fluid Dynamics (CFD) requires a higher density of measurement points, especially in the vicinity of maximum compressor efficiency to analyze different geometries. The requirement to measure different point distributions at fixed rotational speed is the logical consequence. The primary objective of this paper is to develop and evaluate a methodology that allows different operating point distributions of compressor speed lines for the compressor mapping on the hot-gas test bench. The secondary objective deals with the prediction of the measurement points with respect to pressure ratio and volume flow rate at a fixed rotational speed. This facilitates the pre-selection of settings on the hot-gas test bench.

The study of a tractor diesel engine operation on ethanol and rapeseed oil at various speed modes

Trudy NAMI ◽  
2022 ◽  
pp. 53-59
Author(s):  
A. N. Kozlov ◽  
M. I. Araslanov
Keyword(s):  
Diesel Engine ◽  
Rapeseed Oil ◽  
Power Plants ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Renewable Energy Sources ◽  
Comparative Method ◽  
Combustion Process ◽  
Engine Operation ◽  
Tractor Diesel

Introduction (problem statement and relevance). The depletion of oil fuels reserves and the steady growth of their consumption will require new solutions in the development of technologies based on renewable energy sources. The study of the possible alternative fuels use in internal combustion engines is a complex scientific task, including the research of the alternative fuels effect on the power plants operation efficiency.The purpose of the study was to obtain the speed characteristics of a diesel engine operating on ethyl alcohol and rapeseed oil.Methodology and research methods. An air-cooled with volumetric mixture formation tractor diesel engine of dimension 2Ch 10.5/12.0 was selected as an object of research. The study was carried out by a comparative method. To measure the speed characteristic a fixed cyclic fuel supply was applied after the engine reaching the nominal operating mode at a crankshaft speed of 1800 min-1 and an average effective pressure in the cylinder of 0.588 MPa. This approach, with the all-mode regulator of the fuel pump turned off, made it possible to identify the main regularities of intra-cylinder processes at different speed modes of engine operation.Scientific novelty and results. The article presents the bench tests results of a diesel engine operating at various speed modes on ethanol and rapeseed oil, and analyzes in detail the main indicators of the combustion process and the effective engine performance in comparison to the use of traditional fuel. The practical significance lies in the possibility of using the obtained results to improve the diesel engines operation on alternative renewable fuels.

An Experimental Study of Normal-Hexadecane and Iso-Dodecane Binary Fuel Blends in a Military Diesel Engine

2012 ◽  
Author(s):  
Leonard J. Hamilton ◽  
Jim S. Cowart ◽  
Dianne Luning-Prak ◽  
Patrick A. Caton
Keyword(s):  
Experimental Study ◽  
Diesel Engine ◽  
Fuel Injection ◽  
Cetane Number ◽  
Straight Chain ◽  
Load Range ◽  
Binary Blends ◽  
Engine Operation ◽  
Fuel Blends ◽  
Branched Alkanes

The molecular composition of new hydrotreated renewable fuels consists of both straight chain and branched alkanes. These new fuels do not contain aromatic or cyclo-paraffinic hydro-carbon compounds which are regularly seen in conventional petroleum fuels. Both experimental and modeling work has shown that straight chain alkanes have shorter ignition delays (e.g. higher cetane number) as compared to branched alkanes. In order to better understand the effects of branched and straight chain alkanes fuels in diesel engines, an experimental study was pursued using binary blends of iso-dodecane (iC12H26 with abbreviation: iC12) and normal-hexadecane (nC16H34 with abbreviation nC16) in a military diesel engine (AM General HMMWV ‘Humvee’ engine). Mixtures of 50% iC12 with 50% nC16 as well as 25% iC12 with 75% nC16 were compared to 100% nC16 (cetane) fueled engine operation across the entire speed-load range. Higher nC16 fuel content operation resulted in modestly earlier fuel injection events and combustion phasing that delievered slightly worse engine brake performance (torque and fuel consumption). Interestingly, ignition delay and overall burn durations were relatively insensitive to the binary blends tested. The significantly different physical properties of iC12 relative to nC16 are believed to affect the fuel injection event leading to later fuel injection with increasing iC12 content. Later injection into a hotter chamber mitigates the lower cetane number of the higher iC12 content fuel blends.

scholarly journals Combustion and Emission Characteristics of a Diesel Engine Operating with Varying Equivalence Ratio and Compression Ratio - A CFD Simulation

2020 ◽  
Vol 01 (03) ◽  
pp. 101-110
Author(s):  
Kazi Mostafijur Rahman ◽  
Zobair Ahmed
Keyword(s):  
Diesel Engine ◽  
Compression Ratio ◽  
Equivalence Ratio ◽  
Internal Combustion Engines ◽  
Cfd Simulation ◽  
Combustion Engine ◽  
Computational Cost ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Engine Operation

The performance of diesel engine highly depends on atomization, vaporization and mixing of fuel with air. These factors are strongly influenced by various parameters e.g. injection pressure, injection timing, compression ratio, equivalence ratio, cylinder geometry, in cylinder air motion etc. In this study, a diesel engine has been investigated by employing a commercial CFD software (ANSYS Forte, version 18.1) especially developed for internal combustion engines (ICE) modeling; focusing primarily on the effects of equivalence ratio and compression ratio on combustion and emission characteristics. RNG k-ε model was employed as the turbulence model for analyzing the physical phenomena involved in the change of kinetic energy. In order to reduce the computational cost and time, a sector mesh of 45o angle with periodic boundary conditions applied at the periodic faces of the sector, is considered instead of using the whole engine geometry. Simulations are performed for a range of equivalence ratio varying from 0.6 to 1.2 and for three compression ratios namely, 15:1, 18:1 and 21:1. Results show that, improvement in combustion characteristics with higher compression ratio could be achieved for both lean and rich mixtures. Peak in-cylinder pressure and peak heat release nearer to TDC are achieved for compression ratio of 18:1 that could results in more engine torque. For compression ratio beyond 16:1, effects of fuel concentration on ignition delay is more pronounced. At lower compression ratio, in-cylinder temperature is not sufficiently high for atomization, vaporization, mixing of fuel with air, and preflame reactions to occur immediately after the fuel injection. NOx emission in diesel engine increases due to higher pressure and temperature inside the cylinder associated with relatively higher compression ratio. Rich mixture leads to more CO and unburnt hydrocarbon emission compared to lean mixture as result of incomplete combustion. Engine operation with too high compression ratio is detrimental as emission is a major concern.

Sign in / Sign up

Export Citation Format

Share Document