scholarly journals Enhancing electrical properties of carbon nanotubes thin films by silicon incorporation

2021 ◽  
Vol 1206 (1) ◽  
pp. 012028
Author(s):  
Sk Faruque Ahmed ◽  
Mohibul Khan ◽  
Nillohit Mukherjee
Keyword(s):  
Thin Films ◽  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Chemical Vapor ◽  
Binding Energies ◽  
Xps Spectra ◽  
X Ray ◽  
Vapor Deposition Technique

Abstract Silicon incorporated carbon nanotube (Si-CNTs) thin films was prepared by radio frequency plasma enhanced chemical vapor deposition technique. Tetraethyl orthosilicate solution was used for incorporation of silicon in CNTs thin films. Energy dispersive X-ray analysis shows that the silicon atomic percentage was varied from 0 % to 6.1 %. The chemical binding energies of carbon and silicon were analyzed from X-ray photoelectron spectroscopy data. The various peaks at ~531 eV, ~ 285 eV, ~155 eV and ~104 eV was observed in the XPS spectra due to the oxygen, carbon and silicon respectively. Surface morphologies of Si-CNTs thin films have been analyzed by field emission scanning electron microscopy, which revels that the length of the silicon incorporated carbon nanotubes ~500 nm and corresponding diameter ~80 nm. The room temperature electrical conductivity was increased whereas the activation energy was decreased with the increase of atomic percentage of silicon in Si-CNTs thin films. The room temperature electrical conductivity was increased from 4.3 × 103 to 7.1 × 104 S cm−1 as the silicon atomic percentage in Si-CNTs thin films increases from 0 to 6.1 % respectively.

scholarly journals Enhancement of Electrical Property of Carbon Nanotube by Silicon Incorporation

2020 ◽  
Vol 10 (1) ◽  
pp. 62-65
Keyword(s):  
Thin Films ◽  
Electrical Conductivity ◽  
Photoelectron Spectroscopy ◽  
Chemical Vapor ◽  
Binding Energies ◽  
Xps Spectra ◽  
X Ray ◽  
Conductivity Increase ◽  
Vapor Deposition Technique ◽  
Si Content

Silicon incorporated carbon nano tube has been synthesized by radio frequency plasma enhanced chemical vapor deposition technique with acetylene gas. Tetraethyl orthosilicate solution was used for the synthesis of silicon incorporation in the CNT thin films. Energy dispersive X-ray analysis shows that the Si atomic percentage in the CNT thin films varied from 0 % to 3.82 %. The different chemical binding energies of carbon and silicon were analyzed from X-ray photoelectron spectroscopy spectra. In the XPS spectra, the peaks at ~531 eV, ~ 285 eV, ~151 eV and ~100 eV are the contributions from O 1s, C 1s, Si 2s and Si 2p respectively. Nanostructure morphologies of the Si-CNT thin films have been analyzed by field emission scanning electron microscopy. The length of the silicon incorporated carbon nano tubes ~100 nm and corresponding diameter ~20 nm. The increase of atomic percentage of Si in the CNT thin films, room temperature electrical conductivity increases. The electrical conductivity increase from 3.87x103 to 4.49x104 S cm-1 as the silicon atomic percentage in the CNT thin films increases from 0 to 3.82 % respectively. This study showed that the Si-CNTs thin films potentially useful in electrical application of varying its conductivity by changing the Si content independently from other parameters

scholarly journals Deposit of AlN thin films by nitrogen reactive pulsed laser ablation using an Al target

2019 ◽  
Vol 65 (4 Jul-Aug) ◽  
pp. 345 ◽  
Author(s):  
F. Chale-Lara ◽  
M. Zapata-Torres ◽  
F. Caballero-Briones ◽  
W. De la Cruz ◽  
N. Cruz Gonzalez ◽  
...  
Keyword(s):  
Thin Films ◽  
Laser Ablation ◽  
Photoelectron Spectroscopy ◽  
Hexagonal Phase ◽  
Pulsed Laser ◽  
Pulsed Laser Ablation ◽  
Nitrogen Pressure ◽  
Binding Energies ◽  
Xps Spectra ◽  
X Ray

We report the synthesis of AlN hexagonal thin films by pulsed laser ablation, using Al target in nitrogen ambient over natively-oxidized Si (111) at 600°C. Composition and chemical state were determined by X-ray photoelectron spectroscopy (XPS); while structural properties were investigated using X-ray diffraction (XRD). High-resolution XPS spectra present a gradual shift to higher binding energies on the Al2ppeak when nitrogen pressure is incremented, indicating the formation of the AlN compound. At 30 mTorr nitrogen pressure, theAl2p peak corresponds to AlN, located at 73.1 eV, and the XRD pattern shows a hexagonal phase of AlN. The successful formation of the AlN compound is corroborated by UV-Vis reflectivity measurements.

scholarly journals Optical Constant and Conformality Analysis of SiO2 Thin Films Deposited on Linear Array Microstructure Substrate by PECVD

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 510
Author(s):  
Yongqiang Pan ◽  
Huan Liu ◽  
Zhuoman Wang ◽  
Jinmei Jia ◽  
Jijie Zhao
Keyword(s):  
Thin Films ◽  
Film Thickness ◽  
Deposition Rate ◽  
Optical Constant ◽  
Photoelectron Spectroscopy ◽  
Linear Array ◽  
Chemical Vapor ◽  
Rf Plasma ◽  
X Ray ◽  
Sio2 Thin Film

SiO2 thin films are deposited by radio frequency (RF) plasma-enhanced chemical vapor deposition (PECVD) technique using SiH4 and N2O as precursor gases. The stoichiometry of SiO2 thin films is determined by the X-ray photoelectron spectroscopy (XPS), and the optical constant n and k are obtained by using variable angle spectroscopic ellipsometer (VASE) in the spectral range 380–1600 nm. The refractive index and extinction coefficient of the deposited SiO2 thin films at 500 nm are 1.464 and 0.0069, respectively. The deposition rate of SiO2 thin films is controlled by changing the reaction pressure. The effects of deposition rate, film thickness, and microstructure size on the conformality of SiO2 thin films are studied. The conformality of SiO2 thin films increases from 0.68 to 0.91, with the increase of deposition rate of the SiO2 thin film from 20.84 to 41.92 nm/min. The conformality of SiO2 thin films decreases with the increase of film thickness, and the higher the step height, the smaller the conformality of SiO2 thin films.

Structure and Conductivity of Iodine-Doped C60 Thin Films

1994 ◽  
Vol 359 ◽  
Author(s):  
Jun Chen ◽  
Haiyan Zhang ◽  
Baoqiong Chen ◽  
Shaoqi Peng ◽  
Ning Ke ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Conductivity ◽  
Room Temperature ◽  
Conductivity Measurements ◽  
X Ray Diffraction ◽  
Temperature Conductivity ◽  
Room Temperature Conductivity ◽  
X Ray ◽  
Thermally Activated ◽  
Order Of Magnitude

ABSTRACTWe report here the results of our study on the properties of iodine-doped C60 thin films by IR and optical absorption, X-ray diffraction, and electrical conductivity measurements. The results show that there is no apparent structural change in the iodine-doped samples at room temperature in comparison with that of the undoped films. However, in the electrical conductivity measurements, an increase of more that one order of magnitude in the room temperature conductivity has been observed in the iodine-doped samples. In addition, while the conductivity of the undoped films shows thermally activated temperature dependence, the conductivity of the iodine-doped films was found to be constant over a fairly wide temperature range (from 20°C to 70°C) exhibiting a metallic feature.

Use of anti-solvent to enhance thermoelectric response of hybrid-halide perovskite thin films

2022 ◽  
Author(s):  
Shrikant SAINI ◽  
Izuki Matsumoto ◽  
Sakura Kishishita ◽  
Ajay Kumar Baranwal ◽  
Tomohide Yabuki ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Conductivity ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Cost Effective ◽  
Performance Tuning ◽  
Charge Carrier Density ◽  
X Ray ◽  
Thermoelectric Energy Harvesting ◽  
Halide Perovskite

Abstract Hybrid halide perovskite has been recently focused on thermoelectric energy harvesting due to the cost-effective fabrication approach and ultra-low thermal conductivity. To achieve high performance, tuning of electrical conductivity is a key parameter that is influenced by grain boundary scattering and charge carrier density. The fabrication process allows tuning these parameters. We report the use of anti-solvent to enhance the thermoelectric performance of lead-free hybrid halide perovskite, CH3NH3SnI3, thin films. Thin films with anti-solvent show higher connectivity in grains and higher Sn+4 oxidation states which results in enhancing the value of electrical conductivity. Thin films were prepared by a cost-effective wet process. Structural and chemical characterizations were performed using x-ray diffraction, scanning electron microscope, and x-ray photoelectron spectroscopy. The value of electrical conductivity and the Seebeck coefficient were measured near room temperature. The high value of power factor (1.55 µW/m.K2 at 320 K) was achieved for thin films treated with anti-solvent.

Electronic structure modification in Fe substituted β-Ga2O3 from resonant photoemission and soft x-ray absotption spectroscopies

2021 ◽  
Author(s):  
Sahadeb Ghosh ◽  
Mangala Nand ◽  
Rajiv Kamparath ◽  
Mukul Gupta ◽  
Devdatta M Phase ◽  
...  
Keyword(s):  
Thin Films ◽  
Photoelectron Spectroscopy ◽  
Rf Magnetron Sputtering ◽  
Binding Energies ◽  
Transfer System ◽  
Structure Modification ◽  
X Ray ◽  
Resonant Photoemission ◽  
A Charge ◽  
Fe Substitution

Abstract Oriented thin films of β-(Ga1-xFex)2O3 have been deposited by RF magnetron sputtering on c-Al2O3 and GaN substrates. The itinerant character of Fe 3d states forming the top of the valence band (VB) of Fe substituted of β-Ga2O3 thin films has been determined from resonant photoelectron spectroscopy (RPES). Further, admixture of itinerant and localized character of these Fe 3d sates is obtained for larger binding energies i.e deeper of VB. The bottom of the conduction band (CB) for β-(Ga1-xFex)2O3 is also found to be strongly hybridized states involving Fe 3d and O 2p states as compared to that of Ga 4s in pristine β-Ga2O3. This suggests that β-Ga2O3 transforms from band like system to a charge transfer system with Fe substitution. Furthermore, the bandgap red shits with Fe composition, which has been found to be primarily related to the shift of the CB edge.

scholarly journals Increased Electrical Conductivity of Carbon Nanotube Fibers by Thermal and Voltage Annealing

2021 ◽  
Vol 8 (1) ◽  
pp. 1
Author(s):  
Varun Shenoy Gangoli ◽  
Chris J. Barnett ◽  
James D. McGettrick ◽  
Alvin Orbaek White ◽  
Andrew R. Barron
Keyword(s):  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Raman Spectroscopy ◽  
Photoelectron Spectroscopy ◽  
Separate Analysis ◽  
Sweet Spot ◽  
Electrical Conductor ◽  
X Ray ◽  
Resonant Raman ◽  
Carbon Nanotube Fibers

We report the effect of annealing, both electrical and by applied voltage, on the electrical conductivity of fibers spun from carbon nanotubes (CNTs). Commercial CNT fibers were used as part of a larger goal to better understand the factors that go into making a better electrical conductor from CNT fibers. A study of thermal annealing in a vacuum up to 800 °C was performed on smaller fiber sections along with a separate analysis of voltage annealing up to 7 VDC; both exhibited a sweet spot in the process as determined by a combination of a two-point probe measurement with a nanoprobe, resonant Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). Scaled-up tests were then performed in order to translate these results into bulk samples inside a tube furnace, with similar results that indicate the potential for an optimized method of achieving a better conductor sample made from CNT fibers. The results also help to determine the surface effects that need to be overcome in order to achieve this.

Growth of Highly Oriented Zinc Oxide Thin Films by Plasma Enhanced Chemical Vapor Deposition

2006 ◽  
Vol 321-323 ◽  
pp. 1687-1690 ◽  
Author(s):  
Hee Joon Kim ◽  
Dong Young Jang ◽  
Prem Kumar Shishodia ◽  
Akira Yoshida
Keyword(s):  
Thin Films ◽  
Zinc Oxide ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Photoelectron Spectroscopy ◽  
Visible Region ◽  
Chemical Vapor ◽  
Zno Films ◽  
X Ray ◽  
Crystalline Films

In the paper, zinc oxide (ZnO) thin films are deposited by plasma enhanced chemical vapor deposition (PECVD) at different substrate temperatures. The ZnO films are characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The analysis results indicate that highly crystalline films with high orientation can be obtained at a substrate temperature of 300 oC with 50 ml/min flow rate from Diethylzinc (DEZ). Furthermore, the investigation of optical property shows that ZnO films are transparent, and the peak transmittance in the visible region is as high as 85%.

Characterization of europium implanted LiNbO3

1993 ◽  
Vol 8 (10) ◽  
pp. 2679-2685 ◽  
Author(s):  
P. Moretti ◽  
B. Canut ◽  
S.M.M. Ramos ◽  
R. Brenier ◽  
P. Thévenard ◽  
...  
Keyword(s):  
Single Crystals ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Rutherford Backscattering ◽  
Oxidation States ◽  
Xps Spectra ◽  
X Ray ◽  
Partial Recrystallization ◽  
Lower Charge

LiNbO3 single crystals were implanted at room temperature with Eu+ ions at 70 keV with fluence ranging from 0.5 to 5 × 1016 ions · cm−2. The damage in the implanted layer has been investigated by Channeling Rutherford Backscattering (RBS-C), and the oxidation states of the cations have been determined by x-ray photoelectron spectroscopy (XPS). Following implantation, a fully amorphized layer of 60 nm is generated, even for the lowest fluence employed. Subsequent annealing in air, in the range 800–1250 K, was applied to restore tentatively the crystallinity and promote the substitutional incorporation of Eu in the crystal. Only a partial recrystallization of the damaged layer was observed. For as-implanted samples, XPS spectra clearly reveal europium in Eu2+ and Eu3+ states, and the Nb5+ ions are driven to lower charge states.

Sign in / Sign up

Export Citation Format

Share Document