scholarly journals Development of magnesium calcium phosphate biocement for bone regeneration

2010 ◽  
Vol 7 (49) ◽  
pp. 1171-1180 ◽  
Author(s):  
Junfeng Jia ◽  
Huanjun Zhou ◽  
Jie Wei ◽  
Xin Jiang ◽  
Hong Hua ◽  
...  
Keyword(s):  
Calcium Phosphate ◽  
Cell Attachment ◽  
Setting Time ◽  
Molar Ratio ◽  
Dihydrogen Phosphate ◽  
Good Ability ◽  
Degradation Ratio ◽  
Close Proximity ◽  
Proliferation And Differentiation ◽  
Fast Dissolution

Magnesium calcium phosphate biocement (MCPB) with rapid-setting characteristics was fabricated by using the mixed powders of magnesium oxide (MgO) and calcium dihydrogen phosphate (Ca(H 2 PO 4 ) 2 ·H 2 O). The results revealed that the MCPB hardened after mixing the powders with water for about 7 min, and the compressive strength reached 43 MPa after setting for 1 h, indicating that the MCPB had a short setting time and high initial mechanical strength. After the acid–base reaction of MCPB containing MgO and Ca(H 2 PO 4 ) 2 ·H 2 O in a molar ratio of 2 : 1, the final hydrated products were Mg 3 (PO 4 ) 2 and Ca 3 (PO 4 ) 2 . The MCPB was degradable in Tris–HCl solution and the degradation ratio was obviously higher than calcium phosphate biocement (CPB) because of its fast dissolution. The attachment and proliferation of the MG 63 cells on the MCPB were significantly enhanced in comparison with CPB, and the alkaline phosphatase activity of MG 63 cells on the MCPB was significantly higher than on the CPB at 7 and 14 days. The MG 63 cells with normal phenotype spread well on the MCPB surfaces, and were attached in close proximity to the substrate, as seen by scanning electron microscopy (SEM). The results demonstrated that the MCPB had a good ability to support cell attachment, proliferation and differentiation, and exhibited good cytocompatibility.

Injectable calcium phosphate and styrene–butadiene polymer-based root canal filling material

2021 ◽  
Vol 15 (1) ◽  
pp. 19-26
Author(s):  
Hala B. Kaka ◽  
Raid F. Salman
Keyword(s):  
Calcium Phosphate ◽  
Root Canal ◽  
Setting Time ◽  
Molar Ratio ◽  
Styrene Butadiene Rubber ◽  
Filling Material ◽  
Butadiene Rubber ◽  
Root Canal Filling ◽  
Phosphate Powder ◽  
Styrene Butadiene

Abstract Background Three-dimensional obturation of the root canal system is mandatory for a successful root canal treatment. Using a filling material with optimal properties may enable the root canal to be sealed well and therefore obtain the desired obturation. Objective To develop a new injectable paste endodontic filling material using calcium phosphate powder and a styrene–butadiene emulsion polymer. Methods The powder phase comprised an equivalent molar ratio of tetracalcium phosphate, anhydrous dicalcium phosphate, bismuth oxide, and calcium chloride. The liquid phase comprised a styrene–butadiene rubber emulsion in distilled water. The powder and the liquid were mixed to achieve a paste consistency. The paste was subjected to various tests including flow, setting time, dimensional change, solubility, and radiopacity to indicate its suitability as a root canal filling material. All these tests were conducted according to the American National Standards Institute–American Dental Association for endodontic sealing materials. After passing these tests, the paste was submitted to an injectability test. Results The material showed acceptable flowability with 19.1 ± 1.3 min setting time and 0.61 ± 0.16% shrinkage after 30 days of storage. We found the highest solubility at 24 h (6.62 ± 0.58%), then the solubility decreased to 1.09 ± 0.08% within 3 days. The material was more radiopaque than a 3 mm step on an aluminum wedge. Furthermore, the material showed good injectability of 93.67 ± 1.80%. Conclusions The calcium phosphate powder in styrene–butadiene emulsion met basic requirements for a root canal filling material with promising properties.

Proliferation and Differentiation of MC3T3-E1 Cells on Calcium Phosphate/Chitosan Coatings

2008 ◽  
Vol 87 (7) ◽  
pp. 650-654 ◽  
Author(s):  
J. Wang ◽  
J. de Boer ◽  
K. de Groot
Keyword(s):  
Calcium Phosphate ◽  
Stromal Cell ◽  
Bone Marrow Stromal Cell ◽  
Cell Attachment ◽  
Bone Sialoprotein ◽  
Differentiation Potential ◽  
Collagen Expression ◽  
Significant Difference ◽  
Proliferation And Differentiation ◽  
Proliferative Ability

The incorporation of chitosan into electro-deposited calcium phosphate (CaP) coatings increases bone marrow stromal cell attachment. We hypothesized that such electrodeposited CaP/chitosan coatings can also enhance the proliferative ability and differentiation potential of osteoblasts. To verify this hypothesis, we cultured osteoblast-like MC3T3-E1 cells on these CaP coatings. It was found that MC3T3-E1 cells cultured on the electrodeposited CaP/chitosan coatings had cell proliferation rates higher than those on the electrodeposited CaP coatings. At the same time, both alkaline phosphatase activity and collagen expression were increased, and both bone sialoprotein and osteocalcin genes were up-regulated when MC3T3-E1 cells were cultured on the electrodeposited CaP/chitosan coatings. Additionally, within the range of selected chitosan concentrations in solution, no significant difference was found between the CaP/chitosan coatings. Our results suggest that the electrodeposited CaP/chitosan coatings are favorable to the proliferation and differentiation of MC3T3-E1 cells, which may endow them with great potential for future applications.

scholarly journals Cellular Performance Comparison of Biomimetic Calcium Phosphate Coating and Alkaline-Treated Titanium Surface

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Xiaohua Yu ◽  
Mei Wei
Keyword(s):  
Calcium Phosphate ◽  
Titanium Surface ◽  
Cell Attachment ◽  
Substrate Surface ◽  
Calcium Phosphate Coating ◽  
Osteoblastic Cell ◽  
Phosphate Coating ◽  
Proliferation And Differentiation ◽  
The Impact

The influence of biomimetic calcium phosphate coating on osteoblasts behaviorin vitrois not well established yet. In this study, we investigated the behavior of osteoblastic rat osteosarcoma 17/2.8 cells (ROS17/2.8) on two groups of biomaterial surfaces: alkaline-treated titanium surface (ATT) and biomimetic calcium phosphate coated ATT (CaP). The cell attachment, proliferation, differentiation, and morphology on these surfaces were extensively evaluated to reveal the impact of substrate surface on osteoblastic cell responses. It was found that the ROS17/2.8 cells cultured on the ATT surface had higher attachment and proliferation rates compared to those on the CaP surface. Our results also showed that the calcium phosphate coatings generated in this work have an inhibiting effect on osteoblast adhesion and further influenced the proliferation and differentiation of osteoblast compared to the ATT surfacein vitro. Cells on the ATT surface also exhibited a higher alkaline phosphatase activity than on the CaP surface after two weeks of culture. Immunofluorescence staining and scanning electron microscopy results showed that the cells adhered and spread faster on the ATT surface than on the CaP surface. These results collectively suggested that substrate surface properties directly influence cell adhesion on different biomaterials, which would result in further influence on the cell proliferation and differentiation.

scholarly journals Incorporation of Poly(Vinyl Alcohol) for The Improved Properties of Hydrothermal Derived Calcium Phosphate Cements

2018 ◽  
Vol 18 (2) ◽  
pp. 354
Author(s):  
Nurul Nabilah Razali ◽  
Iis Sopyan
Keyword(s):  
Calcium Phosphate ◽  
Vinyl Alcohol ◽  
Setting Time ◽  
Poly Vinyl Alcohol ◽  
Dihydrogen Phosphate ◽  
Distilled Water ◽  
Ammonium Dihydrogen Phosphate ◽  
Hydrothermal Route ◽  
Ringer’S Solution ◽  
Setting Times

Calcium phosphate cement (CPC) has been synthesized via a straightforward hydrothermal route. Calcium oxide and ammonium dihydrogen phosphate were used as calcium and phosphate precursors. The precursors were refluxed in distilled water at 90–100 °C and dried overnight until the calcium phosphate powder was formed. CPC was then produced by mixing the powder and distilled water at the powder-to-liquid (P/L) ratio of 1.5. Poly(vinyl alcohol) (PVA) of 1 to 7% (w/w) was added and its effect on physical properties was investigated. It was proved that PVA addition up to 7% (w/w) has shortened the setting time but decreased the injectability. The PVA free CPC has the initial and final setting times of 71 and 187 min, respectively and the injectability of 99.92%. The compressive strength also increased with the amount of PVA added in CPC. In addition, soaking CPC in Ringer's solution for 7, 14 and 21 days also gave remarkable effects on cohesion, microstructure and mechanical properties of the cement.

Injectable calcium phosphate and styrene–butadiene polymer-based root canal filling material

2021 ◽  
Vol 15 (1) ◽  
pp. 19-26
Author(s):  
Hala B. Kaka ◽  
Raid F. Salman
Keyword(s):  
Calcium Phosphate ◽  
Root Canal ◽  
Setting Time ◽  
Molar Ratio ◽  
Styrene Butadiene Rubber ◽  
Filling Material ◽  
Butadiene Rubber ◽  
Root Canal Filling ◽  
Phosphate Powder ◽  
Styrene Butadiene

Abstract Background Three-dimensional obturation of the root canal system is mandatory for a successful root canal treatment. Using a filling material with optimal properties may enable the root canal to be sealed well and therefore obtain the desired obturation. Objective To develop a new injectable paste endodontic filling material using calcium phosphate powder and a styrene–butadiene emulsion polymer. Methods The powder phase comprised an equivalent molar ratio of tetracalcium phosphate, anhydrous dicalcium phosphate, bismuth oxide, and calcium chloride. The liquid phase comprised a styrene–butadiene rubber emulsion in distilled water. The powder and the liquid were mixed to achieve a paste consistency. The paste was subjected to various tests including flow, setting time, dimensional change, solubility, and radiopacity to indicate its suitability as a root canal filling material. All these tests were conducted according to the American National Standards Institute–American Dental Association for endodontic sealing materials. After passing these tests, the paste was submitted to an injectability test. Results The material showed acceptable flowability with 19.1 ± 1.3 min setting time and 0.61 ± 0.16% shrinkage after 30 days of storage. We found the highest solubility at 24 h (6.62 ± 0.58%), then the solubility decreased to 1.09 ± 0.08% within 3 days. The material was more radiopaque than a 3 mm step on an aluminum wedge. Furthermore, the material showed good injectability of 93.67 ± 1.80%. Conclusions The calcium phosphate powder in styrene–butadiene emulsion met basic requirements for a root canal filling material with promising properties.

scholarly journals Pure hydroxyapatite synthesis originating from amorphous calcium carbonate

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Michika Sawada ◽  
Kandi Sridhar ◽  
Yasuharu Kanda ◽  
Shinya Yamanaka
Keyword(s):  
Calcium Carbonate ◽  
Calcium Phosphate ◽  
Room Temperature ◽  
Molar Ratio ◽  
Final Phase ◽  
Amorphous Calcium Carbonate ◽  
Phosphate Compound ◽  
Synthesis Strategy ◽  
Phosphorylation Reaction ◽  
Subsequent Calcination

AbstractWe report a synthesis strategy for pure hydroxyapatite (HAp) using an amorphous calcium carbonate (ACC) colloid as the starting source. Room-temperature phosphorylation and subsequent calcination produce pure HAp via intermediate amorphous calcium phosphate (ACP). The pre-calcined sample undergoes a competitive transformation from ACC to ACP and crystalline calcium carbonate. The water content, ACC concentration, Ca/P molar ratio, and pH during the phosphorylation reaction play crucial roles in the final phase of the crystalline phosphate compound. Pure HAp is formed after ACP is transformed from ACC at a low concentration (1 wt%) of ACC colloid (1.71 < Ca/P < 1.88), whereas Ca/P = 1.51 leads to pure β-tricalcium phosphate. The ACP phases are precursors for calcium phosphate compounds and may determine the final crystalline phase.

scholarly journals Mineralization of Titanium Surfaces: Biomimetic Implants

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2879
Author(s):  
Javier Gil ◽  
Jose Maria Manero ◽  
Elisa Ruperez ◽  
Eugenio Velasco-Ortega ◽  
Alvaro Jiménez-Guerra ◽  
...  
Keyword(s):  
Calcium Phosphate ◽  
Dental Implants ◽  
Early Stage ◽  
Calcium Phosphates ◽  
Biological Fixation ◽  
Biomimetic Surfaces ◽  
Titanium Surfaces ◽  
Deposition Processes ◽  
Fast Dissolution ◽  
Plasma Sprayed

The surface modification by the formation of apatitic compounds, such as hydroxyapatite, improves biological fixation implants at an early stage after implantation. The structure, which is identical to mineral content of human bone, has the potential to be osteoinductive and/or osteoconductive materials. These calcium phosphates provoke the action of the cell signals that interact with the surface after implantation in order to quickly regenerate bone in contact with dental implants with mineral coating. A new generation of calcium phosphate coatings applied on the titanium surfaces of dental implants using laser, plasma-sprayed, laser-ablation, or electrochemical deposition processes produces that response. However, these modifications produce failures and bad responses in long-term behavior. Calcium phosphates films result in heterogeneous degradation due to the lack of crystallinity of the phosphates with a fast dissolution; conversely, the film presents cracks, which produce fractures in the coating. New thermochemical treatments have been developed to obtain biomimetic surfaces with calcium phosphate compounds that overcome the aforementioned problems. Among them, the chemical modification using biomineralization treatments has been extended to other materials, including composites, bioceramics, biopolymers, peptides, organic molecules, and other metallic materials, showing the potential for growing a calcium phosphate layer under biomimetic conditions.

Glycans in scaffold design in tissue reconstruction

2021 ◽  
pp. 088391152199784
Author(s):  
Nipun Jain ◽  
Shashi Singh
Keyword(s):  
Cell Attachment ◽  
Low Cost ◽  
Growth Conditions ◽  
Downstream Signaling ◽  
Cell Carrier ◽  
Wide Range ◽  
Proliferation And Differentiation ◽  
Different Types ◽  
Tissue Reconstruction ◽  
A Cell

Development of an artificial tissue by tissue engineering is witnessed to be one of the long lasting clarified solutions for the damaged tissue function restoration. To accomplish this, a scaffold is designed as a cell carrier in which the extracellular matrix (ECM) performs a prominent task of controlling the inoculated cell’s destiny. ECM composition, topography and mechanical properties lead to different types of interactions between cells and ECM components that trigger an assortment of cellular reactions via diverse sensing mechanisms and downstream signaling pathways. The polysaccharides in the form of proteoglycans and glycoproteins yield better outcomes when included in the designed matrices. Glycosaminoglycan (GAG) chains present on proteoglycans show a wide range of operations such as sequestering of critical effector morphogens which encourage proficient nutrient contribution toward the growing stem cells for their development and endurance. In this review we discuss how the glycosylation aspects are of considerable importance in everyday housekeeping functions of a cell especially when placed in a controlled environment under ideal growth conditions. Hydrogels made from these GAG chains have been used extensively as a resorbable material that mimics the natural ECM functions for an efficient control over cell attachment, permeability, viability, proliferation, and differentiation processes. Also the incorporation of non-mammalian polysaccharides can elicit specific receptor responses which authorize the creation of numerous vigorous frameworks while prolonging the low cost and immunogenicity of the substance.

scholarly journals A bone replacement-type calcium phosphate cement that becomes more porous in vivo by incorporating a degradable polymer

2021 ◽  
Vol 32 (7) ◽  
Author(s):  
Akiyoshi Shimatani ◽  
Hiromitsu Toyoda ◽  
Kumi Orita ◽  
Yuta Ibara ◽  
Yoshiyuki Yokogawa ◽  
...  
Keyword(s):  
Calcium Phosphate ◽  
Calcium Phosphate Cement ◽  
Alginic Acid ◽  
Setting Time ◽  
Zealand White Rabbit ◽  
Control Group ◽  
Degradable Polymer ◽  
Low Viscosity ◽  
Bone Replacement

AbstractThis study investigated whether mixing low viscosity alginic acid with calcium phosphate cement (CPC) causes interconnected porosity in the CPC and enhances bone replacement by improving the biological interactions. Furthermore, we hypothesized that low viscosity alginic acid would shorten the setting time of CPC and improve its strength. CPC samples were prepared with 0, 5, 10, and 20% low viscosity alginic acid. After immersion in acetate buffer, possible porosification in CPC was monitored in vitro using scanning electron microscopy (SEM), and the setting times and compressive strengths were measured. In vivo study was conducted by placing CPC in a hole created on the femur of New Zealand white rabbit. Microcomputed tomography and histological examination were performed 6 weeks after implantation. SEM images confirmed that alginic acid enhanced the porosity of CPC compared to the control, and the setting time and compressive strength also improved. When incorporating a maximum amount of alginic acid, the new bone mass was significantly higher than the control group (P = 0.0153). These biological responses are promising for the translation of these biomaterials and their commercialization for clinic applications.

The Effect of Phosphatic Composite on Magnesium Phosphate Cement Performance

2014 ◽  
Vol 809-810 ◽  
pp. 477-484
Author(s):  
Zhao Qing Qi ◽  
Hong Tao Wang ◽  
Jun Liang Dang ◽  
Shi Hao Zhang ◽  
Jian Hua Ding
Keyword(s):  
Setting Time ◽  
Potassium Dihydrogen Phosphate ◽  
Magnesium Phosphate ◽  
Dihydrogen Phosphate ◽  
Ammonium Dihydrogen Phosphate ◽  
Hydrogen Phosphate ◽  
Sodium Dihydrogen Phosphate ◽  
Disodium Hydrogen Phosphate ◽  
Potassium Dihydrogen ◽  
Sodium Dihydrogen

The capacity of 10%, 30%, and 50% ammonium dihydrogen phosphate were replaced with an equal amount of three phosphate (potassium dihydrogen phosphate, sodium dihydrogen phosphate, disodium hydrogen phosphate) respectively. Magnesium phosphate cement was made by phosphate of replaced, which strength, setting time, fluidity, hydration temperature, and the hydration products was researched. The results show that: MPC was made that replaced with the equal amount of three kind of phosphate, which has good mechanical properties. Setting time and fluidity change along with the replacment. Three kind of phosphate replace ammonium dihydrogen phosphate, which change the hydration process of MPC. When ammonium dihydrogen phosphate was replaced by an equal amount of disodium hydrogen phosphate, the temperature of hydration is only 69.4 °C. XRD showed that the diffraction peaks of composite’s magnesium phosphate cement increases.

Sign in / Sign up

Export Citation Format

Share Document