scholarly journals Sulfur resistance of Ce-Mn/TiO 2 catalysts for low-temperature NH 3 –SCR

2018 ◽  
Vol 5 (3) ◽  
pp. 171846 ◽  
Author(s):  
Quan Xu ◽  
Wenjing Yang ◽  
Shitong Cui ◽  
Jason Street ◽  
Yan Luo
Keyword(s):  
Low Temperature ◽  
Photoelectron Spectroscopy ◽  
Conversion Rate ◽  
Active Sites ◽  
Sol Gel ◽  
Textural Properties ◽  
Catalyst Loading ◽  
Impregnation Method ◽  
No Conversion ◽  
X Ray

Ce-Mn/TiO 2 catalyst prepared using a simple impregnation method demonstrated a better low-temperature selective catalytic reduction of NO with NH 3 (NH 3 –SCR) activity in comparison with the sol-gel method. The Ce-Mn/TiO 2 catalyst loading with 20% Ce had the best low-temperature activity and achieved a NO conversion rate higher than 90% at 140–260°C with a 99.7% NO conversion rate at 180°C. The Ce-Mn/TiO 2 catalyst only had a 6% NO conversion rate decrease after 100 ppm of SO 2 was added to the stream. When SO 2 was removed from the stream, the catalyst was able to recover completely. The crystal structure, morphology, textural properties and valence state of the metals involving the novel catalysts were investigated using X-ray diffraction, N 2 adsorption and desorption analysis, X-ray photoelectron spectroscopy, scanning electron microscopy and energy dispersive spectroscopy, respectively. The decrease of NH 3 –SCR performance in the presence of 100 ppm SO 2 was due to the decrease of the surface area, change of the pore structure, the decrease of Ce 4+ and Mn 4+ concentration and the formation of the sulfur phase chemicals which blocked the active sites and changed the valence status of the elements.

scholarly journals CO Oxidation over Metal Oxide (La2O3, Fe2O3, PrO2, Sm2O3, and MnO2) Doped CuO-Based Catalysts Supported on Mesoporous Ce0.8Zr0.2O2 with Intensified Low-Temperature Activity

Catalysts ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 724 ◽  
Author(s):  
Yan Cui ◽  
Leilei Xu ◽  
Mindong Chen ◽  
Chufei Lv ◽  
Xinbo Lian ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
Low Temperature ◽  
Metal Oxide ◽  
Metal Oxides ◽  
Co Oxidation ◽  
Active Sites ◽  
Earth Metal ◽  
High Dispersion ◽  
Impregnation Method ◽  
X Ray

CuO-based catalysts are usually used for CO oxidation owing to their low cost and excellent catalytic activities. In this study, a series of metal oxide (La2O3, Fe2O3, PrO2, Sm2O3, and MnO2)-doped CuO-based catalysts with mesoporous Ce0.8Zr0.2O2 support were simply prepared by the incipient impregnation method and used directly as catalysts for CO catalytic oxidation. These mesoporous catalysts were systematically characterized by X-ray powder diffraction (XRD), N2 physisorption, transmission electron microscopy (TEM), energy-dispersed spectroscopy (EDS) mapping, X-ray photoelectron spectroscopy (XPS), and H2 temperature programmed reduction (H2-TPR). It was found that the CuO and the dopants were highly dispersed among the mesoporous framework via the incipient impregnation method, and the strong metal framework interaction had been formed. The effects of the types of the dopants and the loading amounts of the dopants on the low-temperature catalytic performances were carefully studied. It was concluded that doped transition metal oxides could regulate the oxygen mobility and reduction ability of catalysts, further improving the catalytic activity. It was also found that the high dispersion of rare earth metal oxides (PrO2, Sm2O3) was able to prevent the thermal sintering and aggregation of CuO-based catalysts during the process of calcination. In addition, their presence also evidently improved the reducibility and significantly reduced the particle size of the CuO active sites for CO oxidation. The results demonstrated that the 15CuO-3Fe2O3/M-Ce80Zr20 catalyst with 3 wt. % of Fe2O3 showed the best low-temperature catalytic activity toward CO oxidation. Overall, the present Fe2O3-doped CuO-based catalysts with mesoporous nanocrystalline Ce0.8Zr0.2O2 solid solution as support were considered a promising series of catalysts for low-temperature CO oxidation.

Recyclable Heterogeneous Fe-Mo Nanocatalyst: Application in Solvent Free Synthesis of β-enaminones

2019 ◽  
Vol 6 (3) ◽  
pp. 238-247
Author(s):  
Swapnil R. Bankar
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Significant Loss ◽  
Solvent Free ◽  
Catalyst Loading ◽  
Spectroscopic Techniques ◽  
Impregnation Method ◽  
Molybdenum Catalyst ◽  
X Ray ◽  
Solvent Free Condition

<P>Background: In recent years, green organic transformation has become a challenge for a chemist in areas like social sector, health, and environment. Literature survey revealed that a nano magnetite supported heterogeneous catalysis is an emergent field with huge application in chemical synthesis. </P><P> Objective: In the present article, the aim was to develop a simple and facile method to carry organic reaction under benign media. So, the focus was on the synthesis of nano-magnetite supported molybdenum catalyst and its application in β-enaminones synthesis. </P><P> Methods: Magnetically recyclable heterogeneous ferrite-molybdenum catalyst was prepared by simple impregnation method. The synthesized nanocatalyst Fe-Mo was well analysed by spectroscopic techniques like X-ray diffraction analysis, X-ray photoelectron spectroscopy, transmission electron microscopy, field-emission gun scanning electron microscopy and vibrating-sample magnetometry. The functionalized nanocatalyst Fe-Mo was employed in the synthesis of β-enaminones under solvent free condition. </P><P> Results: The competency of synthesized nanocatalyst-Fe-Mo was observed to be good for the synthesis of β-enaminones derivatives under microwave irradiation and gave excellent yield (86-96%) of the product. The catalyst was recycled for more than five consecutive runs without significant loss in its activity. </P><P> Conclusion: In the present research article, synthesis of highly active, magnetically recyclable Fe- Mo nanocatalyst was obtained from easily available precursor. The MNP was stable under investigated conditions and effective in β-enaminones synthesis. The simple eco-friendly method, low catalyst loading, short transformation time, and reusability of the catalyst thoroughly follow the sustainable protocol.</P>

Composition and Chemical Structure of Nitrided Silica Gel

1984 ◽  
Vol 32 ◽  
Author(s):  
R. K. Brow ◽  
C. G. Pantano
Keyword(s):  
Thin Films ◽  
Infrared Spectroscopy ◽  
Low Temperature ◽  
Silica Gel ◽  
Photoelectron Spectroscopy ◽  
Chemical Structure ◽  
Sol Gel ◽  
X Ray ◽  
Higher Temperature ◽  
Low Temperature Treatments

ABSTRACTSol/gel derived silica thin films were thermally treated in NH3 for four hours at temperatures up to 1300C. The films were analyzed by ellipsometry, X-ray photoelectron spectroscopy (XPS) and infrared spectroscopy (IR). Over 30 mol% nitrogen was incorporated in the film treated at 1300C. Using IR and XPS analyses, -NHx groups were found to be present after low temperature treatments, while nitrogen was incorporated in an oxynitride structure after the higher temperature treatments.

scholarly journals Alumina Coated Silica Nanosprings (NS) Support Based Cobalt Catalysts for Liquid Hydrocarbon Fuel Production From Syngas

Materials ◽  
2019 ◽  
Vol 12 (11) ◽  
pp. 1810
Author(s):  
Abdulbaset Alayat ◽  
Elena Echeverria ◽  
Farid Sotoudehniakarani ◽  
David N. Mcllroy ◽  
Armando G. McDonald
Keyword(s):  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Fixed Bed ◽  
Chemical Properties ◽  
Hydrocarbon Fuel ◽  
Liquid Hydrocarbon ◽  
Cobalt Catalysts ◽  
Impregnation Method ◽  
X Ray ◽  
Co Conversion

The effects of Al2O3 coating on the performance of silica nanospring (NS) supported Co catalysts for Fischer–Tropsch synthesis (FTS) were evaluated in a quartz fixed-bed microreactor. The Co/NS-Al2O3 catalysts were synthesized by coating the Co/NS and NS with Al2O3 by an alkoxide-based sol-gel method (NS-Al-A and NS-Al-B, respectively) and then by decorating them with Co. Co deposition was via an impregnation method. Catalysts were characterized before the FTS reaction by the Brunauer–Emmett–Teller (BET) method, X-ray diffraction, transmission electron microscopy, temperature programmed reduction, X-ray photoelectron spectroscopy, differential thermal analysis and thermogravimetric analysis in order to find correlations between physico-chemical properties of catalysts and catalytic performance. The products of the FTS were trapped and analyzed by GC-TCD and GC-MS to determine the CO conversion and reaction selectivity. The Al2O3 coated NS catalyst had a significant affect in FTS activity and selectivity in both Co/NS-Al2O3 catalysts. A high CO conversion (82.4%) and Σ > C6 (86.3%) yield were obtained on the Co/NS-Al-B catalyst, whereas the CO conversion was 62.8% and Σ > C6 was 58.5% on the Co/NS-Al-A catalyst under the same FTS experimental condition. The Co/NS-Al-A catalyst yielded the aromatic selectivity of 10.2% and oxygenated compounds.

scholarly journals Study of Catalytic Combustion of Dioxins on Ce-V-Ti Catalysts Modified by Graphene Oxide in Simulating Iron Ore Sintering Flue Gas

Materials ◽  
2019 ◽  
Vol 13 (1) ◽  
pp. 125
Author(s):  
Qi Shi ◽  
Long Ding ◽  
Hong-Ming Long ◽  
Tie-Jun Chun
Keyword(s):  
Low Temperature ◽  
Flue Gas ◽  
Photoelectron Spectroscopy ◽  
Catalytic Combustion ◽  
Catalytic Mechanism ◽  
Sol Gel ◽  
Critical Role ◽  
Electron Interaction ◽  
Graphene Oxides ◽  
X Ray

Ce-V-Ti and Ce-V-Ti/GO catalysts synthesized by the sol-gel method were used for the catalytic combustion of dioxins at a low temperature under simulating sintering flue gas in this paper. The catalytic mechanism of Ce-V-Ti catalysts modified with graphene oxides (GO) at a low temperature was revealed through X-ray diffractometer (XRD), Brunauer–Emmett–Teller (BET), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), H2-temperature-programmed reduction (H2-TPR) and Fourier transform infrared (FTIR). During the tests, chlorobenzene (CB) was used as a model reagent since the dioxins are poisonous. The results showed that introducing GO to Ce-V-Ti catalysts can improve the specific surface area and promote the CB adsorption on the surface of catalysts. Simultaneously, the Ce-V-Ti with 0.7 wt % GO support showed the high activity with the conversion of 60% at 100 °C and 80% at 150 °C. The adsorb ability of catalysts is strengthened by the electron interaction between GO and CB through π-π bond. In the case of Ce-V-Ti catalysts, Ce played a major catalytic role and V acted as a co-catalytic composition. After GO modification, the concentration of Ce3+ and V4+ were enlarged. The synergy between Ce3+ and V3+ played the critical role on the low-temperature performance of catalysts under sintering flue gas.

scholarly journals Selective Hydrogenation of Naphthalene over γ-Al2O3-Supported NiCu and NiZn Bimetal Catalysts

Catalysts ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 1215 ◽  
Author(s):  
Jingqiu Li ◽  
Liu Shi ◽  
Gang Feng ◽  
Zhangping Shi ◽  
Chenglin Sun ◽  
...  
Keyword(s):  
Selective Hydrogenation ◽  
Photoelectron Spectroscopy ◽  
Active Sites ◽  
Density Functional ◽  
Surface Engineering ◽  
Rational Surface ◽  
Impregnation Method ◽  
X Ray ◽  
Hydrogenation Activity ◽  
Calculation Results

A series of Cu and Zn modified Ni/Al2O3 catalysts were prepared using an incipient impregnation method for the selective hydrogenation of naphthalene into tetralin. X-ray diffraction (XRD), H2-Temperature programmed reduction (H2-TPR), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) were applied to reveal the structure regulation, and density functional theory (DFT) calculations were performed to investigate the electronic effect and reactant adsorptions on the active sites. The results showed that the addition of CuO promoted the hydrogenation of naphthalene with an inhibited tetraline selectivity. However, a simultaneously increasing naphthalene conversion and tetraline selectivity were achieved over the Zn modified Ni/Al2O3 catalysts. The characterization and calculation results revealed that the doping of CuO improved the hydrogenation activity with a low tetralin selectivity due to the H spillover from the Cu. The addition of ZnO decreased the interaction between NiOx and Al2O3 in NiZn/Al2O3 catalysts, which efficiently increased the reduction ability of NiOx species and, thus, improved the naphthalene hydrogenation activity. The electron transfer from ZnO to NiOx weakened the adsorption of tetraline and resulted in increased tetraline selectivity. This work provides insight into developing efficient catalysts for heavy aromatics conversions via rational surface engineering.

scholarly journals Effect of Ce Addition on Adsorption and Oxidation of NO over MnO x /Al2O3

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Chunhui Mou ◽  
Hui Li ◽  
Ning Dong ◽  
Shien Hui ◽  
Denghui Wang
Keyword(s):  
Catalytic Activity ◽  
Catalytic Oxidation ◽  
Photoelectron Spectroscopy ◽  
Active Sites ◽  
Catalyst Surface ◽  
Fixed Bed ◽  
No Oxidation ◽  
Impregnation Method ◽  
X Ray ◽  
Oxidation Of No

The MnO x /Al2O3 catalysts with different Ce content doping were prepared by an ultrasonic impregnation method, and the catalytic activity for NO oxidation removal was tested in a fixed-bed quartz tube furnace. Simultaneously, the catalysts were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), full-automatic physical-chemical adsorption instrument, and field emission scanning electron microscope (FESEM) to analyze the effect of Ce addition on the adsorption capacity and catalytic activity. Experimental results validated that the activity of the MnO x /Al2O3 catalyst was greatly promoted with Ce addition. According to the characterization results, it could be concluded that Ce doping led to significant changes in the crystalline phase on the catalyst surface, which increased the relative content of surface lattice oxygen and promoted the catalytic oxidation of NO. By observing the physical properties of the surface and analyzing the surface elements of the catalyst, it could be inferred that a manganese-cerium solid solution was formed on the surface of Mn0.4Ce0.05/Al. Moreover, Ce addition increased the catalyst pore size, which enhanced the adsorption and contact of NO and O2 with the active sites on the catalyst surface, and reduced the resistance of the reactants during internal diffusion. All these variations assigned to Mn0.4Ce0.05/Al were favorable for the catalytic oxidation of NO.

Structural/Texture Evolution During Facile Substitution of Ni into ZSM-5 Nanostructure vs. its Impregnation Dispersion Used in Selective Transformation of Methanol to Ethylene and Propylene

2020 ◽  
Vol 23 ◽  
Author(s):  
Parisa Sadeghpour ◽  
Mohammad Haghighi ◽  
Mehrdad Esmaeili
Keyword(s):  
High Temperature ◽  
Physicochemical Properties ◽  
Active Sites ◽  
Catalytic Performance ◽  
Fixed Bed Reactor ◽  
Light Olefins ◽  
Isomorphous Substitution ◽  
Impregnation Method ◽  
Hydrothermal Temperature ◽  
X Ray

Aim and Objective: Effect of two different modification methods for introducing Ni into ZSM-5 framework was investigated under high temperature synthesis conditions. The nickel successfully introduced into the MFI structures at different crystallization conditions to enhance the physicochemical properties and catalytic performance. Materials and Methods: A series of impregnated Ni/ZSM-5 and isomorphous substituted NiZSM-5 nanostructure catalysts were prepared hydrothermally at different high temperatures and within short times. X-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM), Energy dispersive X-ray (EDX), Brunner, Emmett and Teller-Barrett, Joyner and Halenda (BET-BJH), Fourier transform infrared (FTIR) and Temperature-programmed desorption of ammonia (TPDNH3) were applied to investigate the physicochemical properties. Results: Although all the catalysts showed pure silica MFI–type nanosheets and coffin-like morphology, using the isomorphous substitution for Ni incorporation into the ZSM-5 framework led to the formation of materials with lower crystallinity, higher pore volume and stronger acidity compared to using impregnation method. Moreover, it was found that raising the hydrothermal temperature increased the crystallinity and enhanced more uniform incorporation of Ni atoms in the crystalline structure of catalysts. TPD-NH3 analysis demonstrated that high crystallization temperature and short crystallization time of NiZSM-5(350-0.5) resulted in fewer weak acid sites and medium acid strength. The MTO catalytic performance was tested in a fixed bed reactor at 460ºC and GHSV=10500 cm3 /gcat.h. A slightly different reaction pathway was proposed for the production of light olefins over impregnated Ni/ZSM-5 catalysts based on the role of NiO species. The enhanced methanol conversion for isomorphous substituted NiZSM-5 catalysts could be related to the most accessible active sites located inside the pores. Conclusion: The impregnated Ni/ZSM-5 catalyst prepared at low hydrothermal temperature showed the best catalytic performance, while the isomorphous substituted NiZSM-5 prepared at high temperature was found to be the active molecular sieve regarding the stability performance.

scholarly journals Elucidation of the Crystal Growth Characteristics of SnO2 Nanoaggregates Formed by Sequential Low-Temperature Sol-Gel Reaction and Freeze Drying

Nanomaterials ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1738
Author(s):  
Saeid Vafaei ◽  
Alexander Wolosz ◽  
Catlin Ethridge ◽  
Udo Schnupf ◽  
Nagisa Hattori ◽  
...  
Keyword(s):  
Crystal Growth ◽  
Low Temperature ◽  
Photoelectron Spectroscopy ◽  
High Performance ◽  
Freeze Drying ◽  
Sno2 Nanoparticles ◽  
Sol Gel ◽  
Functional Materials ◽  
Cost Effective ◽  
High Concentration

SnO2 nanoparticles are regarded as attractive, functional materials because of their versatile applications. SnO2 nanoaggregates with single-nanometer-scale lumpy surfaces provide opportunities to enhance hetero-material interfacial areas, leading to the performance improvement of materials and devices. For the first time, we demonstrate that SnO2 nanoaggregates with oxygen vacancies can be produced by a simple, low-temperature sol-gel approach combined with freeze-drying. We characterize the initiation of the low-temperature crystal growth of the obtained SnO2 nanoaggregates using high-resolution transmission electron microscopy (HRTEM). The results indicate that Sn (II) hydroxide precursors are converted into submicrometer-scale nanoaggregates consisting of uniform SnO2 spherical nanocrystals (2~5 nm in size). As the sol-gel reaction time increases, further crystallization is observed through the neighboring particles in a confined part of the aggregates, while the specific surface areas of the SnO2 samples increase concomitantly. In addition, X-ray photoelectron spectroscopy (XPS) measurements suggest that Sn (II) ions exist in the SnO2 samples when the reactions are stopped after a short time or when a relatively high concentration of Sn (II) is involved in the corresponding sol-gel reactions. Understanding this low-temperature growth of 3D SnO2 will provide new avenues for developing and producing high-performance, photofunctional nanomaterials via a cost-effective and scalable method.

scholarly journals Enhanced Photocatalytic Activity of CuWO4 Doped TiO2 Photocatalyst Towards Carbamazepine Removal under UV Irradiation

Separations ◽  
2021 ◽  
Vol 8 (3) ◽  
pp. 25
Author(s):  
Chukwuka Bethel Anucha ◽  
Ilknur Altin ◽  
Emin Bacaksız ◽  
Tayfur Kucukomeroglu ◽  
Masho Hilawie Belay ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Pure Tio2 ◽  
Component Part ◽  
Energy Yield ◽  
Mechanical Agitation ◽  
X Ray

Abatement of contaminants of emerging concerns (CECs) in water sources has been widely studied employing TiO2 based heterogeneous photocatalysis. However, low quantum energy yield among other limitations of titania has led to its modification with other semiconductor materials for improved photocatalytic activity. In this work, a 0.05 wt.% CuWO4 over TiO2 was prepared as a powder composite. Each component part synthesized via the sol-gel method for TiO2, and CuWO4 by co-precipitation assisted hydrothermal method from precursor salts, underwent gentle mechanical agitation. Homogenization of the nanopowder precursors was performed by zirconia ball milling for 2 h. The final material was obtained after annealing at 500 °C for 3.5 h. Structural and morphological characterization of the synthesized material has been achieved employing X-ray diffraction (XRD), Fourier transform infra-red (FTIR) spectroscopy, Brunauer–Emmett–Teller (BET) N2 adsorption–desorption analysis, Scanning electron microscopy-coupled Energy dispersive X-ray spectroscopy (SEM-EDS), Transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and UV-Vis diffuse reflectance spectroscopy (UV-vis DRS) for optical characterization. The 0.05 wt.% CuWO4-TiO2 catalyst was investigated for its photocatalytic activity over carbamazepine (CBZ), achieving a degradation of almost 100% after 2 h irradiation. A comparison with pure TiO2 prepared under those same conditions was made. The effect of pH, chemical scavengers, H2O2 as well as contaminant ion effects (anions, cations), and humic acid (HA) was investigated, and their related influences on the photocatalyst efficiency towards CBZ degradation highlighted accordingly.

Sign in / Sign up

Export Citation Format

Share Document