Optimizations of RZ5-TiC magnesium matrix composite wear parameters using Taguchi approach

2018 ◽  
Vol 70 (5) ◽  
pp. 907-914 ◽  
Author(s):  
Deepak Mehra ◽  
Manas Mohan Mahapatra ◽  
Suraj Prakash Harsha
Keyword(s):  
Weight Loss ◽  
Wear Resistance ◽  
Coefficient Of Friction ◽  
Significant Influence ◽  
Optimization Approach ◽  
Optimum Level ◽  
Taguchi Approach ◽  
Content Type ◽  
Taguchi Orthogonal Design ◽  
Sliding Distance

Purpose The advancement in modern manufacturing technology generated the need to develop new materials for better wear resistance. The purpose of this paper is to use the Taguchi optimization approach to examine which wear parameter significantly affects weight loss and coefficient of friction for RZ5-TiC composite. It is a simple and efficient method to find performance of wear parameter using minimum experimental runs. Design/methodology/approach RZ5-TiC composites were prepared using RZ5 as matrix, reinforced with TiC through self-propagating high-temperature synthesis technique. In the present work, an attempt has been made to study the influence of wear parameters like applied load (AL), sliding distance (SD) and Wt.% of TiC (WTC) on responses like weight loss and coefficient of friction of RZ5/TiCp composites. The pin-on-disc apparatus used to conduct abrasive wear test. The wear process parameters are optimized for minimum wear based on L27 Taguchi orthogonal design. The Taguchi technique using design of experiments (DOE) is used to obtain the data. The ANOVA and an orthogonal array are used to examine the influence of wear parameters on responses. The purpose is to examine parametric significances which affect responses. Findings It observed that wear parameters have the significant influence on responses of RZ5/TiCp composites. The interaction of sliding distance/Wt.% of TiC is observed and found significant influence on both responses. The optimum level of the significant wear parameters is achieved based on the maximum S/N ratio for RZ5/TiCp composites. The optimal interaction for weight loss and coefficient of friction is AL1-SD1-WTC3 and AL3-SD1-WTC3, respectively. Finally, the confirmation test is conducted and the results are obtained within the confidence interval. Originality/value The current manuscript provides an optimization of wear parameters using Taguchi approach. The extensive experimental data are used for this purpose and effects of wear parameters on responses are analyzed from the presented results. The results obtained are useful in improving the wear resistance of the RZ5-TiC composite.

Effect of wear parameters on dry abrasive wear of RZ5-TiC in situ composite

2018 ◽  
Vol 70 (2) ◽  
pp. 256-263 ◽  
Author(s):  
Deepak Mehra ◽  
Manas Mohan Mahapatra ◽  
Suraj Prakash Harsha
Keyword(s):  
Weight Loss ◽  
Wear Resistance ◽  
Abrasive Wear ◽  
Coefficient Of Friction ◽  
Applied Load ◽  
Mg Alloy ◽  
Ceramic Particles ◽  
Content Type ◽  
Sliding Distance

Purpose The purpose of this study is to increase the wear resistance of Mg alloy by adding hard ceramic particles to it. The inclusion of hard ceramic particles further strengthen the Mg alloy, resulting in higher wear resistance. Mg alloys containing Zn, rare earth and Zr exhibit high specific strength and excellent creep resistance, making them suitable for aerospace components such as aircraft gearboxes and generator housings. Design/methodology/approach In the present study, composites have been produced in situ by using RZ5 mg alloy as matrix and TiC as reinforcement by self-propagating high-temperature synthesis technique. The abrasive wear behavior of RZ5 Mg alloy matrix reinforced with TiC particulates has also been examined. The pin-on-disc apparatus has been used for the tests. The abrasive paper is used as a counter body, and the results are obtained by changing sliding distance and applied load. Findings A notable enhancement in the wear resistance and mechanical properties of tested composite has been observed as compared to the RZ5 Mg alloy as a matrix. There is a uniform increment in the change in weight loss of RZ5-TiC composite with increasing sliding distance and applied load, but it decreases with increasing TiC content. The coefficient of friction (µ) also decreases uniformly with an increase in the reinforcement of TiC, but it decreases with an increase in applied load and sliding distance. The investigation of the worn composite, which determines dominant wear mechanisms as abrasion and plowing grooves on tested samples, has been done using field emission scanning electron microscopy. Originality/value The current manuscript provides a detailed abrasive wear analysis of RZ5-TiC composite by using different wear parameters. Specifically, extensive experimental data have been provided for RZ5-TiC composite. The effects of parameters such as applied load, sliding distance and Wt.% of TiC on the weight loss and coefficient of friction of the composites have been analyzed and discussed thoroughly.

Abrasive wear analysis of RZ5/TiC in-situ composites: a statistical approach

2019 ◽  
Vol 71 (9) ◽  
pp. 1029-1037
Author(s):  
Deepak Mehra ◽  
Manas Mohan Mahapatra ◽  
Suraj Prakash Harsha
Keyword(s):  
Weight Loss ◽  
Statistical Analysis ◽  
Abrasive Wear ◽  
Coefficient Of Friction ◽  
Control Parameters ◽  
Content Type ◽  
Wear Analysis ◽  
Full Factorial ◽  
Sliding Distance

Purpose The RZ5 mg alloy is used in automotive and aerospace applications including helicopter gearboxes and aircraft components. These components are prone to the wear as per the demands. The present work is the study of the significance of hard particle/ceramic, i.e. titanium carbide (TiC) in RZ5 mg alloy to protect the machine components from wear. Design/methodology/approach The abrasive wear analysis of in-situ RZ5-TiC magnesium matrix composite is considered for the study. The primary focus of the present work is to analyze the effects of varying control parameters, i.e. Wt.% of TiC, sliding distance and applied load on the responses, i.e. weight loss and coefficient of friction. Full factorial design of the experiment based on statistical analysis is used. Findings It is observed that the individually Wt.% of TiC and sliding distance show the comparatively significant effect on both responses. Similarly, the interaction between sliding distance and Wt.% of TiC indicated the considerable impact on weight loss. The regression equations are developed and validated for estimating responses. It is observed that the percentage errors are not appearing more than 10 per cent of responses. Therefore, the close agreement between measured and predicted values shows the adequacy of the model. The control factor is optimized using multi-response optimization. The variations of the order of 2.47 and 2.35 per cent in target value of the coefficient of friction and weight loss are achieved. Originality/value The current manuscript provides a detailed abrasive wear statistical analysis of RZ5-TiC composite. The influence of control parameters on the responses using the full factorial design, the main effect plots and interaction effects are presented.

Erosion characteristics on surface texture of additively manufactured AlSi10Mg alloy in SiO2 quartz added slurry environment

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Recep Demirsöz ◽  
Mehmet Erdl Korkmaz ◽  
Munish Kumar Gupta ◽  
Alberto Garcia Collado ◽  
Grzegorz M. Krolczyk
Keyword(s):  
Surface Roughness ◽  
Weight Loss ◽  
Wear Resistance ◽  
Erosive Wear ◽  
Oxide Ceramics ◽  
Slurry Erosion ◽  
Content Type ◽  
Test Setup ◽  
Quartz Sands ◽  
Erosion Test

Purpose The main purpose of this work is to explore the erosion wear characteristics of additively manufactured aluminium alloy. Additive manufacturing (AM), also known as three-dimensional (3D) manufacturing, is the process of manufacturing a part designed in a computer environment using different types of materials such as plastic, ceramic, metal or composite. Similar to other materials, aluminum alloys are also exposed to various wear types during operation. Production efficiency needs to be aware of its reactions to wearing mechanisms. Design/methodology/approach In this study, quartz sands (SiO2) assisted with oxide ceramics were used in the slurry erosion test setup and its abrasiveness on the AlSi10Mg aluminum alloy material produced by the 3D printer as selective laser melting (SLM) technology was investigated. Quartz was sieved with an average particle size of 302.5 µm, and a slurry environment containing 5, 10 and 15% quartz by weight was prepared. The experiments were carried out at the velocity of 1.88 (250 rpm), 3.76 (500 rpm) and 5.64 m/s (750 rpm) and the impact angles 15, 45 and 75°. Findings With these experimental studies, it has been determined that the abrasiveness of quartz sand prepared in certain particle sizes is directly related to the particle concentration and particle speed, and that the wear increases with the increase of the concentration and rotational speed. Also, the variation of weight loss and surface roughness of the alloy was investigated after different wear conditions. Surface roughness values at 750 rpm speed, 10% concentration and 75° impingement angle are 0.32 and 0.38 µm for 0 and 90° samples, respectively, with a difference of approximately 18%. Moreover, concerning a sample produced at 0°, the weight loss at 250 rpm at 10% concentration and 45° particle impact angle is 32.8 mg, while the weight loss at 500 rpm 44.4 mg, and weight loss at 750 rpm is 104 mg. Besides, the morphological structures of eroded surfaces were examined using the scanning electron microscope to understand the wear mechanisms. Originality/value The researchers verified that this specific coating condition increases the slurry wear resistance of the mentioned steel. There are many studies about slurry wear tests; however, there is no study in the literature about the quartz sand (SiO2) assisted slurry-erosive wear of AlSi10Mg alloy produced with AM by using SLM technology. This study is needed to fill this gap in the literature and to examine the erosive wear capability of this current material in different environments. The novelty of the study is the use of SiO2 quartz sands assisted by oxide ceramics in different concentrations for the slurry erosion test setup and the investigations on erosive wear resistance of AlSi10Mg alloy manufactured by AM.

An experimental investigation on friction and wear test parameters of cylinder liner and piston ring pair using Taguchi technique

2018 ◽  
Vol 70 (9) ◽  
pp. 1721-1728 ◽  
Author(s):  
H.K. Trivedi ◽  
D.V. Bhatt
Keyword(s):  
Weight Loss ◽  
Surface Morphology ◽  
Coefficient Of Friction ◽  
Piston Ring ◽  
Minimum Weight ◽  
Load Condition ◽  
Wear Test ◽  
Cylinder Liner ◽  
Content Type ◽  
Control Factors

Purpose The purpose of this paper is to study about tribological parameters of cylinder liner/piston ring under sliding contact in the presence of lubricant. Design/methodology/approach A reciprocating test rig is used for the experimental work. The Taguchi approach has been adopted to optimize the coefficient of friction and minimum weight loss of piston ring and cylinder liner. Three control factors like load, speed and temperature were used for L9 orthogonal array design and ANOVA (analysis of variance). Parameters have been ranked on the basis of experimental outcomes and signal-to-noise (S/N) ratio analysis. Findings It is observed that coefficient of friction was greatly influenced by speed, and weight loss of piston ring and cylinder liner was greatly influenced by load. The surface morphology by SEM (scanning electron microscopy) analysis was used to understand the wear mechanism of worn-out surface and comparative evaluation was made with the Taguchi method. Originality/value Surface morphology of the worn-out surface is significantly dependent on the load condition which validates the ANOVA results.

Wear Characteristics of Al7075/Al2O3/SiC Hybrid Metal Matrix Nano Composites

2021 ◽  
Vol 1034 ◽  
pp. 43-49
Author(s):  
N. Sreedhar
Keyword(s):  
Weight Loss ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Metal Matrix ◽  
Weight Fraction ◽  
Wear Loss ◽  
Matrix Metal ◽  
Wear Characteristics ◽  
The Matrix ◽  
Sliding Distance

In the present investigation Aluminum matrix composites (AMMCs), Al7075 Alloy as matrix metal and Al2O3/SiC particles (2-8%) with an average particulate size of 20, 50 nm as strengthened material have been processed by the stir casting method. For the counter surface wear testing, a computerized pin on a wear tester was used as EN31 (58-60 HRC) steel disc and composite pin. The wear rate for the matrix metal and composites in terms of weight loss per unit sliding distance, friction coefficient, and volume loss were achieved. The composite results show better resistance to wear than matrix metal. SEM was used to investigate the microstructural characterization of worn surfaces. Sample weight loss was calculated and the change in cumulative wear loss at a sliding distance was uniform both for metal matrix as well as for composites. The wear speed for composites was also noted to be small compared to the metal matrix. In addition, experiments have shown that, with the increasing weight fraction of Al2O3/SiC and the coefficient of friction increases with increasing sliding velocity and weight fraction of Al2O3/SiC, the wear rate reduces. The wear characteristics (wear rate, coefficient of friction and wear loss) were better than those of other composites and the matrix metal with 6wt% Al2O3/SiC composites.

TOUGHMET 2CX

Alloy Digest ◽  
2013 ◽  
Vol 62 (6) ◽  
Keyword(s):  
Tensile Strength ◽  
Wear Resistance ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Coefficient Of Friction ◽  
Loading Conditions ◽  
Severe Loading

Abstract ToughMet 2 CX is a Cu-9Ni-6Sn alloy that combines low coefficient of friction with wear resistance. ToughMet alloys are a line of spinodal hardened Cu-Ni antigalling alloys for bearings capable of performing with a variety of shafting materials and lubricants. The alloys combine a high lubricity with wear resistance in these severe loading conditions. ToughMet 2CX in the cast and spinodally hardened (CX) condition exhibits tensile strength in excess of 724 MPa (105 ksi) and hardness exceeding HRC 27 with excellent machinability. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming. Filing Code: Cu-819. Producer or source: Materion Brush Performance Alloys.

Influence of ageing treatment on microstructure, mechanical properties and adhesive wear behaviour of 6063 aluminium alloy

2014 ◽  
Vol 66 (4) ◽  
pp. 520-524 ◽  
Author(s):  
Serkan Büyükdoğan ◽  
Süleyman Gündüz ◽  
Mustafa Türkmen
Keyword(s):  
Mechanical Properties ◽  
Wear Resistance ◽  
High Speed ◽  
Al Alloys ◽  
Wear Behaviour ◽  
Al Alloy ◽  
Strain Ageing ◽  
Content Type ◽  
Static Strain ◽  
Structural Applications

Purpose – The paper aims to provide new observations about static strain ageing in aluminium (Al) alloys which are widely used in structural applications. Design/methodology/approach – The present work aims to provide theoretical and practical information to industries or researchers who may be interested in the effect of static strain ageing on mechanical properties of Al alloys. The data are sorted into the following sections: introduction, materials and experimental procedure, results and discussion and conclusions. Findings – Tensile strength, proof strength (0.2 per cent) and percentage elongation measurement were used to investigate the effect of strain ageing on the mechanical properties. Wear tests were performed by sliding the pin specimens, which were prepared from as-received, solution heat-treated, deformed and undeformed specimens after ageing, on high-speed tool steel (64 HRC). It is concluded that the variations in ageing time improved the strength and wear resistance of the 6063 Al alloy; however, a plastically deformed solution-treated alloy has higher strength and wear resistance than undeformed specimens for different ageing times at 180°C. Practical implications – A very useful source of information for industries using or planning to produce Al alloys. Originality/value – This paper fulfils an identified resource need and offers practical help to the industries.

scholarly journals Effects of Alkyl-Substituted Polybenzoxazines on Tribological Properties of Non-Asbestos Composite Friction Materials

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 567
Author(s):  
Anun Wongpayakyotin ◽  
Chanchira Jubsilp ◽  
Sunan Tiptipakorn ◽  
Phattarin Mora ◽  
Christopher W. Bielawski ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Composite Materials ◽  
Coefficient Of Friction ◽  
Aromatic Amines ◽  
Underlying Structure ◽  
Methyl Groups ◽  
Friction Materials ◽  
Wear Rates ◽  
Structure Properties ◽  
Crosslink Densities

A series of substituted polybenzoxazines was synthesized and studied as binders in non-asbestos friction composite materials. The structures of the polybenzoxazines were varied in a systemic fashion by increasing the number and position of pendant alkyl (methyl) groups and was accomplished using the respective aromatic amines during the polymer synthesis step. By investigating the key thermomechanical and tribological characteristics displayed by the composite materials, the underlying structure-properties relationships were deconvoluted. Composite friction materials with higher thermomechanical and wear resistance properties were obtained from polybenzoxazines with relatively high crosslink densities. In contrast, polybenzoxazines with relatively low crosslink densities afforded composite friction materials with an improved coefficient of friction values and specific wear rates.

scholarly journals Tribological Aspects, Optimization and Analysis of Cu-B-CrC Composites Fabricated by Powder Metallurgy

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4217
Author(s):  
Üsame Ali Usca ◽  
Mahir Uzun ◽  
Mustafa Kuntoğlu ◽  
Serhat Şap ◽  
Khaled Giasin ◽  
...  
Keyword(s):  
Weight Loss ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Applied Load ◽  
Practical Significance ◽  
Tribological Characteristics ◽  
M 10 ◽  
Wide Range ◽  
The Coefficient Of Friction ◽  
Four Levels

Tribological properties of engineering components are a key issue due to their effect on the operational performance factors such as wear, surface characteristics, service life and in situ behavior. Thus, for better component quality, process parameters have major importance, especially for metal matrix composites (MMCs), which are a special class of materials used in a wide range of engineering applications including but not limited to structural, automotive and aeronautics. This paper deals with the tribological behavior of Cu-B-CrC composites (Cu-main matrix, B-CrC-reinforcement by 0, 2.5, 5 and 7.5 wt.%). The tribological characteristics investigated in this study are the coefficient of friction, wear rate and weight loss. For this purpose, four levels of sliding distance (1000, 1500, 2000 and 2500 m) and four levels of applied load (10, 15, 20 and 25 N) were used. In addition, two levels of sliding velocity (1 and 1.5 m/s), two levels of sintering time (1 and 2 h) and two sintering temperatures (1000 and 1050 °C) were used. Taguchi’s L16 orthogonal array was used to statistically analyze the aforementioned input parameters and to determine their best levels which give the desired values for the analyzed tribological characteristics. The results were analyzed by statistical analysis, optimization and 3D surface plots. Accordingly, it was determined that the most effective factor for wear rate, weight loss and friction coefficients is the contribution rate. According to signal-to-noise ratios, optimum solutions can be sorted as: the highest levels of parameters except for applied load and reinforcement ratio (2500 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 0 wt.%) for wear rate, certain levels of all parameters (1000 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 2.5 wt.%) for weight loss and 1000 m, 15 N, 1 m/s, 1 h, 1000 °C and 0 wt.% for the coefficient of friction. The comprehensive analysis of findings has practical significance and provides valuable information for a composite material from the production phase to the actual working conditions.

THE EFFECT OF ELECTROLYTE TEMPERATURE AND SEALING SOLUTION IN ANODIZING OPERATION ON HARDNESS AND WEAR BEHAVIOR OF 7075 -T6 ALUMINUM ALLOY

2019 ◽  
Vol 26 (02) ◽  
pp. 1850143
Author(s):  
SAEED NIYAZBAKHSH ◽  
KAMRAN AMINI ◽  
FARHAD GHARAVI
Keyword(s):  
Weight Loss ◽  
Wear Resistance ◽  
Aluminum Alloy ◽  
Wear Behavior ◽  
Anodic Oxide ◽  
Boiling Water ◽  
Electrolyte Temperature ◽  
Oxide Coatings ◽  
Sodium Dichromate ◽  
Pin On Disk

Anodic oxide coatings are applied on aluminum alloys in order to improve corrosion resistance and to increase hardness and wear resistance. In the current study, a hard anodic coating was applied on AA7075-T6 aluminum alloy. To survey the anodizing temperature (electrolyte temperature) effect, three temperatures, namely, [Formula: see text]C, 0∘C and 5∘C were chosen and the samples were sealed in boiling water and sodium dichromate to study the role of sealing. For measuring the oxide coatings porosity and hardness and also for comparing the samples’ wear resistance field-emission scanning electron microscopy (FESEM), microhardness test and pin-on-disk method were utilized, respectively. The results showed that by increasing the anodizing temperature, hardness and consequently wear resistance decreased so that hardness and weight loss in the samples with no sealing decreased from 460[Formula: see text]HV and 0.61[Formula: see text]mg at [Formula: see text]C to 405 and 358[Formula: see text]HV and 1.05 and 1.12[Formula: see text]mg at 0∘C and 5∘C, respectively, which is due to the porosity increment by increasing the anodizing temperature. Also, sealing in boiling water and dichromate contributed to soft phases and coating hydration, which resulted in a decrease in hardness and wear resistance. Hardness and weight loss in the coated samples at [Formula: see text]C decreased from 460[Formula: see text]HV and 0.61[Formula: see text]mg in the samples with no sealing to 435 and 417[Formula: see text]HV and 0.72 and 0.83[Formula: see text]mg in the samples sealed in boiling water and dichromate, respectively.

Sign in / Sign up

Export Citation Format

Share Document