Predicted Thermal Mismatch Stresses in a Cylindrical Bi-material Assembly Adhesively Bonded at Its Ends

1997 ◽  
Vol 64 (1) ◽  
pp. 15-22 ◽  
Author(s):  
E. Suhir
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Coefficient Of Thermal Expansion ◽  
Stress Model ◽  
Adhesively Bonded ◽  
Thermal Mismatch ◽  
Adhesive Material ◽  
Thermally Induced ◽  
Local Stresses ◽  
Material Assembly

A simple analytical stress model, based on the strength-of-materials approach, is developed for the evaluation of thermally induced shearing stresses in a long cylindrical bi-material assembly adhesively bonded at its ends and subjected to the change in temperature. The emphasis is on the interaction of the “global” thermal mismatch stresses, counted with respect to the mid cross section of the assembly as a whole, and the “local” stresses, counted with respect to the mid cross sections of the bonded regions. The effect of the coefficient of thermal expansion of the adhesive material itself is also considered. We show also how to evaluate the fundamental frequency of vibrations of the inner cylinder with consideration of the thermally induced tension, if any.

scholarly journals Hygrothermal performance of timber-concrete composite panels – theoretical investigation

2020 ◽  
Vol 310 ◽  
pp. 00038
Author(s):  
Viktória Bajzecerová ◽  
Eva Kormaníková ◽  
Ján Kanócz
Keyword(s):  
Mechanical Stress ◽  
Cross Section ◽  
Theoretical Investigation ◽  
Cross Sections ◽  
Composite Panels ◽  
Swimming Pools ◽  
Adhesively Bonded ◽  
Concrete Shrinkage ◽  
Concrete Layer ◽  
Hygrothermal Performance

The concrete layer as a part of the timber-concrete composite (TCC) element makes it possible to maintain the accumulated heat and thus reduce the energy required for heating. Especially for buildings used for a sauna, swimming pools or wellness. In the TCC cross-section due to uneven thermal and humidity deformation of both materials, additional stresses occur. It can lead to the failure of partial cross-sections or composite connection. The aim of the research is to investigate the influence of changing humidity and temperature conditions of the environment on the composite adhesively bonded TCC panels without the influence of other phenomena such as mechanical stress or the effect of concrete shrinkage. The paper presents the results of the preliminary theoretical investigation before the realization of measurements on prepared specimens.

Predicted Thermal Stresses in a Circular Assembly With Identical Adherends and With Application to a Holographic Memory Package Design

2011 ◽  
Vol 79 (1) ◽  
Author(s):  
E. Suhir ◽  
C. Gu ◽  
L. Cao
Keyword(s):  
Elevated Temperature ◽  
Thermal Stresses ◽  
Memory Systems ◽  
Stress Model ◽  
Adhesively Bonded ◽  
Holographic Memory ◽  
Thermally Induced ◽  
Package Design ◽  
Induced Stresses ◽  
Lower Temperature

A simple, easy-to-apply and physically meaningful analytical (“mathematical”) stress model is developed for the prediction of the thermally induced stresses in a circular adhesively bonded assembly with identical adherends. The assembly is fabricated at an elevated temperature and is subsequently cooled down to a lower temperature. The developed model can be helpful for stress-strain analyses and physical design of electronic and photonic assemblies of the type in question, and particularly those employed in holographic memory systems.

scholarly journals TWO-PHASE TURBULENT FLOW IN STRAIGHT HORIZONTAL CHANNELS WITH A SQUARE CROSS-SECTION TAKING INTO ACCOUNT THE INFLUENCE OF VERTICAL FORCES

2018 ◽  
pp. 019
Author(s):  
Saša Milanović ◽  
Miloš Jovanović ◽  
Živan Spasić ◽  
Boban Nikolić
Keyword(s):  
Turbulent Flow ◽  
Cross Section ◽  
Cross Sections ◽  
Flow Direction ◽  
Reynolds Stress Model ◽  
Secondary Flows ◽  
Solid Particles ◽  
Stress Model ◽  
Two Phase ◽  
Mesh Density

The paper presents a numerical simulation of a two-phase turbulent flow in pneumatic transport through straight horizontal channels with a square cross-section. The transport of solid particles of ash and flour is taken as the two-phase flow, while air is chosen for the transporting fluid. The motion of solid particles occurs due to the aerodynamic forces of the transporting fluid. The paper considers the motion of solid particles by taking into account the influence of vertical forces, which act on the transported solid particles. In flow modelling, the transported solid particles are reduced to spherical shapes. The stress model of turbulence is corrected by taking into account the influence of the induction of secondary flows of the second kind in the gas phase. The full Reynolds stress model is used to model the turbulence, with the application of the complete model for turbulent stresses and turbulent temperature fluxes. The paper presents the results of the numerical grid with the highest resolution above which the increase of the mesh density does not affect the obtained results. The diagrams of the positions of the transported solid particles are provided for cross-sections normal and parallel to the flow direction.

Electron Irradiation Effects in Polyoxymethylene Crystals Grown Inside Trioxane Crystals

1971 ◽  
Vol 29 ◽  
pp. 78-79
Author(s):  
J. P. Colson ◽  
D. H. Reneker
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Detailed Examination ◽  
The Other ◽  
Electron Micrograph ◽  
Irradiation Effects ◽  
Threefold Axis ◽  
Typical Sample ◽  
Polymer Crystals ◽  
Chain Axis

Polyoxymethylene (POM) crystals grow inside trioxane crystals which have been irradiated and heated to a temperature slightly below their melting point. Figure 1 shows a low magnification electron micrograph of a group of such POM crystals. Detailed examination at higher magnification showed that three distinct types of POM crystals grew in a typical sample. The three types of POM crystals were distinguished by the direction that the polymer chain axis in each crystal made with respect to the threefold axis of the trioxane crystal. These polyoxymethylene crystals were described previously.At low magnifications the three types of polymer crystals appeared as slender rods. One type had a hexagonal cross section and the other two types had rectangular cross sections, that is, they were ribbonlike.

A quantitative approach to inner shell losses

1978 ◽  
Vol 36 (1) ◽  
pp. 526-527 ◽  
Author(s):  
R.D. Leapman ◽  
P. Rez ◽  
D.F. Mayers
Keyword(s):  
Energy Transfer ◽  
Cross Section ◽  
Cross Sections ◽  
Accurate Determination ◽  
Background Intensity ◽  
Core Excitation ◽  
Quantitative Basis ◽  
Cross Section Differential ◽  
Bound Electrons

Microanalysis by EELS has been developing rapidly and though the general form of the spectrum is now understood there is a need to put the technique on a more quantitative basis (1,2). Certain aspects important for microanalysis include: (i) accurate determination of the partial cross sections, σx(α,ΔE) for core excitation when scattering lies inside collection angle a and energy range ΔE above the edge, (ii) behavior of the background intensity due to excitation of less strongly bound electrons, necessary for extrapolation beneath the signal of interest, (iii) departures from the simple hydrogenic K-edge seen in L and M losses, effecting σx and complicating microanalysis. Such problems might be approached empirically but here we describe how computation can elucidate the spectrum shape.The inelastic cross section differential with respect to energy transfer E and momentum transfer q for electrons of energy E0 and velocity v can be written as

Oxygen K near edge structures studied with multiple scattering calculations

1988 ◽  
Vol 46 ◽  
pp. 504-505
Author(s):  
Xudong Weng ◽  
Peter Rez
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Partial Cross Section ◽  
Energy Window ◽  
Edge Structure ◽  
Fine Structures ◽  
Hydrogenic Model ◽  
Electron Energy Loss ◽  
Quantitative Chemical

In electron energy loss spectroscopy, quantitative chemical microanalysis is performed by comparison of the intensity under a specific inner shell edge with the corresponding partial cross section. There are two commonly used models for calculations of atomic partial cross sections, the hydrogenic model and the Hartree-Slater model. Partial cross sections could also be measured from standards of known compositions. These partial cross sections are complicated by variations in the edge shapes, such as the near edge structure (ELNES) and extended fine structures (ELEXFS). The role of these solid state effects in the partial cross sections, and the transferability of the partial cross sections from material to material, has yet to be fully explored. In this work, we consider the oxygen K edge in several oxides as oxygen is present in many materials. Since the energy window of interest is in the range of 20-100 eV, we limit ourselves to the near edge structures.

Absolute inner-shell cross section determination for EELS analysis

1988 ◽  
Vol 46 ◽  
pp. 534-535
Author(s):  
P.A. Crozier
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Absolute Cross Section ◽  
Specimen Thickness ◽  
Mass Thickness ◽  
Scattering Cross ◽  
Before And After ◽  
Estimated Error ◽  
Scattering Cross Sections ◽  
Electron Microscopist

Absolute inelastic scattering cross sections or mean free paths are often used in EELS analysis for determining elemental concentrations and specimen thickness. In most instances, theoretical values must be used because there have been few attempts to determine experimental scattering cross sections from solids under the conditions of interest to electron microscopist. In addition to providing data for spectral quantitation, absolute cross section measurements yields useful information on many of the approximations which are frequently involved in EELS analysis procedures. In this paper, experimental cross sections are presented for some inner-shell edges of Al, Cu, Ag and Au.Uniform thin films of the previously mentioned materials were prepared by vacuum evaporation onto microscope cover slips. The cover slips were weighed before and after evaporation to determine the mass thickness of the films. The estimated error in this method of determining mass thickness was ±7 x 107g/cm2. The films were floated off in water and mounted on Cu grids.

A technique for preparing semiconductor cross sections for both TEM and SEM analysis

1989 ◽  
Vol 47 ◽  
pp. 712-713
Author(s):  
Stanley J. Klepeis ◽  
J.P. Benedict ◽  
R.M Anderson
Keyword(s):  
Sample Preparation ◽  
Cross Section ◽  
Cross Sections ◽  
Sem Analysis ◽  
Preparation Technique ◽  
Ion Milling ◽  
Tem Analysis ◽  
Polished Cross Section ◽  
Area Of Interest ◽  
Polished Side

The ability to prepare a cross-section of a specific semiconductor structure for both SEM and TEM analysis is vital in characterizing the smaller, more complex devices that are now being designed and manufactured. In the past, a unique sample was prepared for either SEM or TEM analysis of a structure. In choosing to do SEM, valuable and unique information was lost to TEM analysis. An alternative, the SEM examination of thinned TEM samples, was frequently made difficult by topographical artifacts introduced by mechanical polishing and lengthy ion-milling. Thus, the need to produce a TEM sample from a unique,cross-sectioned SEM sample has produced this sample preparation technique.The technique is divided into an SEM and a TEM sample preparation phase. The first four steps in the SEM phase: bulk reduction, cleaning, gluing and trimming produces a reinforced sample with the area of interest in the center of the sample. This sample is then mounted on a special SEM stud. The stud is inserted into an L-shaped holder and this holder is attached to the Klepeis polisher (see figs. 1 and 2). An SEM cross-section of the sample is then prepared by mechanically polishing the sample to the area of interest using the Klepeis polisher. The polished cross-section is cleaned and the SEM stud with the attached sample, is removed from the L-shaped holder. The stud is then inserted into the ion-miller and the sample is briefly milled (less than 2 minutes) on the polished side. The sample on the stud may then be carbon coated and placed in the SEM for analysis.

Experimental Studies Of Multilayer Glass Structures On Compression, Compression With Bending And Simple Bending

2019 ◽  
pp. 22-30
Keyword(s):  
Cross Section ◽  
Cross Sections ◽  
Applied Load ◽  
Experimental Studies ◽  
Strength Properties ◽  
Research Topic ◽  
Normative Values ◽  
Laminated Glass ◽  
The Cross ◽  
Experimental Values

The work of multilayer glass structures for central and eccentric compression and bending are considered. The substantiation of the chosen research topic is made. The description and features of laminated glass for the structures investigated, their characteristics are presented. The analysis of the results obtained when testing for compression, compression with bending, simple bending of models of columns, beams, samples of laminated glass was made. Overview of the types and nature of destruction of the models are presented, diagrams of material operation are constructed, average values of the resistance of the cross-sections of samples are obtained, the table of destructive loads is generated. The need for development of a set of rules and guidelines for the design of glass structures, including laminated glass, for bearing elements, as well as standards for testing, rules for assessing the strength, stiffness, crack resistance and methods for determining the strength of control samples is emphasized. It is established that the strength properties of glass depend on the type of applied load and vary widely, and significantly lower than the corresponding normative values of the strength of heat-strengthened glass. The effect of the connecting polymeric material and manufacturing technology of laminated glass on the strength of the structure is also shown. The experimental values of the elastic modulus are different in different directions of the cross section and in the direction perpendicular to the glass layers are two times less than along the glass layers.

Cross Section Analysis of Cu Filled TSVs Based on High Throughput Plasma-FIB Milling

2012 ◽  
Author(s):  
Frank Altmann ◽  
Jens Beyersdorfer ◽  
Jan Schischka ◽  
Michael Krause ◽  
German Franz ◽  
...  
Keyword(s):  
High Resolution ◽  
Cross Section ◽  
High Throughput ◽  
Cross Sections ◽  
Electron Backscatter Diffraction ◽  
Grain Structure ◽  
Electron Backscatter ◽  
Section Surface ◽  
Backscatter Diffraction ◽  
Section Analysis

Abstract In this paper the new Vion™ Plasma-FIB system, developed by FEI, is evaluated for cross sectioning of Cu filled Through Silicon Via (TSV) interconnects. The aim of the study presented in this paper is to evaluate and optimise different Plasma-FIB (P-FIB) milling strategies in terms of performance and cross section surface quality. The sufficient preservation of microstructures within cross sections is crucial for subsequent Electron Backscatter Diffraction (EBSD) grain structure analyses and a high resolution interface characterisation by TEM.

Sign in / Sign up

Export Citation Format

Share Document