Fabrication of a Cell Culture Plate With a Three-Dimensional Printed Mold and Thermal Analysis of PDMS-Based Casting Process

2018 ◽  
Vol 10 (6) ◽  
Author(s):  
Myo Min Zaw ◽  
William D. Hedrich ◽  
Timothy Munuhe ◽  
Mohamad Hossein Banazadeh ◽  
Hongbing Wang ◽  
...  
Keyword(s):  
Cell Culture ◽  
Temperature Distribution ◽  
Fused Deposition Modeling ◽  
Thermal Damage ◽  
Elevated Temperatures ◽  
Three Dimensional ◽  
Curing Temperature ◽  
Maximum Temperature ◽  
Maximum Temperature Difference ◽  
Fused Deposition

Abstract Polydimethylsiloxane (PDMS)-based casting method was used to fabricate PDMS cell culture platforms with molds printed by a fused deposition modeling (FDM) printer. Cell viability study indicated that the produced plates have the suitable biocompatibility, surface properties, and transparency for cell culture purposes. The molds printed from acrylonitrile-butadiene-syrene (ABS) were reusable after curing at 65 °C, but were damaged at 75 °C. To understand thermal damage to the mold at elevated temperatures, the temperature distribution in an ABS mold during the curing process was predicted using a model that considers conduction, convection, and radiation in the oven. The simulated temperature distribution was consistent with the observed mold deformation. As the maximum temperature difference in the mold did not change appreciably with the curing temperature, we consider that the thermal damage is due to the porous structure that increases the thermal expansion coefficient of the printed material. Our study demonstrated that FDM, an affordable and accessible three-dimensional (3D) printer, has great potential for rapid prototyping of custom-designed cell culture devices for biomedical research.

Dual Extrusion FDM Printer for Flexible and Rigid Polymers

2020 ◽  
Author(s):  
Garrett McGrady ◽  
Kevin Walsh
Keyword(s):  
High Temperature ◽  
Fused Deposition Modeling ◽  
Process Development ◽  
Acrylonitrile Butadiene Styrene ◽  
Polymer Materials ◽  
Robotic Assembly ◽  
Maximum Temperature ◽  
Print Quality ◽  
Maximum Temperature Difference ◽  
Fused Deposition

Abstract Commercially available fused deposition modeling (FDM) printers have yet to bridge the gap between printing soft, flexible materials and printing hard, rigid materials. This work presents a custom printer solution, based on open-source hardware and software, which allows a user to print both flexible and rigid polymer materials. The materials printed include NinjaFlex, SemiFlex, acrylonitrile-butadiene-styrene (ABS), Nylon, and Polycarbonate. In order to print rigid materials, a custom, high-temperature heated bed was designed to act as a print stage. Additionally, high temperature extruders were included in the design to accommodate the printing requirements of both flexible and rigid filaments. Across 25 equally spaced points on the print plate, the maximum temperature difference between any two points on the heated bed was found to be ∼9°C for a target temperature of 170°C. With a uniform temperature profile across the plate, functional prints were achieved in each material. The print quality varied, dependent on material; however, the standard deviation of layer thicknesses and size measurements of the parts were comparable to those produced on a Zortrax M200 printer. After calibration and further process development, the custom printer will be integrated into the NEXUS system — a multiscale additive manufacturing instrument with integrated 3D printing and robotic assembly (NSF Award #1828355).

scholarly journals Fluid flow in a Porous Scaffold for Microtia by Lattice Boltzmann Method

2019 ◽  
Vol 2 (1) ◽  
pp. 46
Author(s):  
Pedro J Boschetti ◽  
Orlando Pelliccioni ◽  
Mariángel Berroterán ◽  
María V. Candal ◽  
Marcos A. Sabino
Keyword(s):  
Cell Culture ◽  
Shear Stress ◽  
Lattice Boltzmann Method ◽  
Lattice Boltzmann ◽  
Fused Deposition Modeling ◽  
Porous Scaffold ◽  
Maximum Shear Stress ◽  
Three Dimensional ◽  
Fused Deposition ◽  
Boltzmann Method

The birth deformity of ear, known as microtia, varies from a minimal deformed ear to the absence of auricular tissue or anotia. This malformation has been treated by reconstructing the external ear, mainly by autogenous rib cartilage in auricular repair. The fabrication of the ear framework is a prolonged reconstructive procedure and depends of the surgeon’s skill. In order to avoid these inconveniences and reduce surgery time, it was proposed in a previous work to use implants made with biocompatible materials. One of these is a scaffold made by fused deposition modeling using PLA based in the three-dimensional geometry of the ear cartilage. The aim of this work is to evaluate the feasibility of this scaffold to perform cell culture in a perfusion biorreactor by estimating the flow transport characteristics in porous media using a scaffold with the porous geometry of the human auricular cartilage for microtia. Flow and heat transfer through the scaffold were simulated by the lattice Boltzmann method, and permeability and shear stress distribution were obtained at different Reynolds numbers. The permeability values of the scaffold achieved are in the order of magnitude of scaffolds used for cell culture. Linear dependencies between maximum shear stress and Reynolds number, and between maximum shear stress and permeability were obtained. The values of shear stress achieved correspond to high percentage of cell viability. The scaffolds for microtia treatment with the proposed filling pattern select is appropriate for cell culture in a perfusion bioreactor with characteristics similar to those described herein.

Thermal characterization of ABS-Graphene blended three dimensional printed functional prototypes for electro chemical energy storage

2018 ◽  
Vol 1 (1) ◽  
pp. 1-11 ◽  
Author(s):  
Kamaljit Singh Boparai ◽  
Rupinder Singh
Keyword(s):  
Energy Storage ◽  
Structural Changes ◽  
Fused Deposition Modeling ◽  
Morphological Changes ◽  
Three Dimensional ◽  
Thermal Characterization ◽  
Chemical Energy ◽  
Flow Index ◽  
Fused Deposition

This study highlights the thermal characterization of ABS-Graphene blended three dimensional (3D) printed functional prototypes by fused deposition modeling (FDM) process. These functional prototypes have some applications as electro-chemical energy storage devices (EESD). Initially, the suitability of ABS-Graphene composite material for FDM applications has been examined by melt flow index (MFI) test. After establishing MFI, the feedstock filament for FDM has been prepared by an extrusion process. The fabricated filament has been used for printing 3D functional prototypes for printing of in-house EESD. The differential scanning calorimeter (DSC) analysis was conducted to understand the effect on glass transition temperature with the inclusion of Graphene (Gr) particles. It has been observed that the reinforced Gr particles act as a thermal reservoir (sink) and enhances its thermal/electrical conductivity. Also, FT-IR spectra realized the structural changes with the inclusion of Gr in ABS matrix. The results are supported by scanning electron microscopy (SEM) based micrographs for understanding the morphological changes.

Extrusion-Based 3D Printing for Pharmaceuticals: Contemporary Research and Applications

2019 ◽  
Vol 24 (42) ◽  
pp. 4991-5008 ◽  
Author(s):  
Mohammed S. Algahtani ◽  
Abdul Aleem Mohammed ◽  
Javed Ahmad
Keyword(s):  
Cosmetic Surgery ◽  
Fused Deposition Modeling ◽  
Personalised Medicine ◽  
Organ Transplant ◽  
Three Dimensional ◽  
Dosage Forms ◽  
Release Profile ◽  
Small Scale ◽  
Drug Release Profile ◽  
Fused Deposition

Three-dimensional printing (3DP) has a significant impact on organ transplant, cosmetic surgery, surgical planning, prosthetics and other medical fields. Recently, 3 DP attracted the attention as a promising method for the production of small-scale drug production. The knowledge expansion about the population differences in metabolism and genetics grows the need for personalised medicine substantially. In personalised medicine, the patient receives a tailored dose and the release profile is based on his pharmacokinetics data. 3 DP is expected to be one of the leading solutions for the personalisation of the drug dispensing. This technology can fabricate a drug-device with complicated geometries and fillings to obtain the needed drug release profile. The extrusionbased 3 DP is the most explored method for investigating the feasibility of the technology to produce a novel dosage form with properties that are difficult to achieve using the conventional industrial methods. Extrusionbased 3 DP is divided into two techniques, the semi-solid extrusion (SSE) and the fused deposition modeling (FDM). This review aims to explain the extrusion principles behind the two techniques and discuss their capabilities to fabricate novel dosage forms. The advantages and limitations observed through the application of SSE and FDM for fabrication of drug dosage forms were discussed in this review. Further exploration and development are required to implement this technology in the healthcare frontline for more effective and personalised treatment.

Development of three-dimensional printing filaments based on poly(lactic acid)/hydroxyapatite composites with potential for tissue engineering

2021 ◽  
pp. 002199832098856
Author(s):  
Marcela Piassi Bernardo ◽  
Bruna Cristina Rodrigues da Silva ◽  
Luiz Henrique Capparelli Mattoso
Keyword(s):  
Tissue Engineering ◽  
Lactic Acid ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Three Dimensional Printing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

Injured bone tissues can be healed with scaffolds, which could be manufactured using the fused deposition modeling (FDM) strategy. Poly(lactic acid) (PLA) is one of the most biocompatible polymers suitable for FDM, while hydroxyapatite (HA) could improve the bioactivity of scaffold due to its chemical composition. Therefore, the combination of PLA/HA can create composite filaments adequate for FDM and with high osteoconductive and osteointegration potentials. In this work, we proposed a different approache to improve the potential bioactivity of 3D printed scaffolds for bone tissue engineering by increasing the HA loading (20-30%) in the PLA composite filaments. Two routes were investigated regarding the use of solvents in the filament production. To assess the suitability of the FDM-3D printing process, and the influence of the HA content on the polymer matrix, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were performed. The HA phase content of the composite filaments agreed with the initial composite proportions. The wettability of the 3D printed scaffolds was also increased. It was shown a greener route for obtaining composite filaments that generate scaffolds with properties similar to those obtained by the solvent casting, with high HA content and great potential to be used as a bone graft.

scholarly journals On the Post-Processing of 3D-Printed ABS Parts

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1559
Author(s):  
Mohammad Reza Khosravani ◽  
Jonas Schüürmann ◽  
Filippo Berto ◽  
Tamara Reinicke
Keyword(s):  
Surface Treatment ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Acrylonitrile Butadiene Styrene ◽  
Experimental Tests ◽  
Fracture Load ◽  
Post Processing ◽  
Fused Deposition ◽  
Dog Bone ◽  
3D Printed

Application of Additive Manufacturing (AM) has significantly increased in the past few years. AM also known as three-dimensional (3D) printing has been currently used in fabrication of prototypes and end-use products. Considering the new applications of additively manufactured components, it is necessary to study structural details of these parts. In the current study, influence of a post-processing on the mechanical properties of 3D-printed parts has been investigated. To this aim, Acrylonitrile Butadiene Styrene (ABS) material was used to produce test coupons based on the Fused Deposition Modeling (FDM) process. More in deep, a device was designed and fabricated to fix imperfection and provide smooth surfaces on the 3D-printed ABS specimens. Later, original and treated specimens were subjected to a series of tensile loads, three-point bending tests, and water absorption tests. The experimental tests indicated fracture load in untreated dog-bone shaped specimen was 2026.1 N which was decreased to 1951.7 N after surface treatment. Moreover, the performed surface treatment was lead and decrease in tensile strength from 29.37 MPa to 26.25 MPa. Comparison of the results confirmed effects of the surface modification on the fracture toughness of the examined semi-circular bending components. Moreover, a 3D laser microscope was used for visual investigation of the specimens. The documented results are beneficial for next designs and optimization of finishing processes.

Synthesis and properties of modified PBT for FDM

2017 ◽  
Vol 23 (4) ◽  
pp. 804-810 ◽  
Author(s):  
Shiqing Cao ◽  
Dandan Yu ◽  
Weilan Xue ◽  
Zuoxiang Zeng ◽  
Wanyu Zhu
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Fused Deposition Modeling ◽  
Complex Structure ◽  
Three Dimensional ◽  
Sebacic Acid ◽  
Wire Drawing ◽  
Content Type ◽  
Fused Deposition ◽  
Deposition Modeling

Purpose The purpose of this paper is to prepare a new modified polybutylene terephalate (MPBT) for fused deposition modeling (FDM) to increase the variety of materials compatible with printing. And the printing materials can be used to print components with a complex structure and functional mechanical parts. Design/methodology/approach The MPBT, poly(butylene terephalate-co-isophthalate-co-sebacate) (PBTIS), was prepared for FDM by direct esterification and subsequent polycondensation using terephthalic acid (PTA), isophthalic acid (PIA), sebacic acid (SA) and 1,4-butanediol (BDO). The effects of the content of PIA (20-40 mol%) on the mechanical properties of PBTIS were investigated when the mole per cent of SA (αSA) is zero. The effects of αSA (0-7mol%) on the thermal, rheological and mechanical properties of PBTIS were investigated at nPTA/nPIA = 7/3. A desktop wire drawing and extruding machine was used to fabricate the filaments, whose printability and anisotropy were tested by three-dimensional (3D) printing experiments. Findings A candidate content of PIA introducing into PBT was obtained to be about 30 per cent, and the Izod notched impact strength of PBTIS increased with the increase of αSA. The results showed that the PBTIS (nPTA/nPIA = 7/3, αSA = 3-5mol%) is suitable for FDM. Originality/value New printing materials with good Izod notched impact strength were obtained by introducing PIA and SA (nPTA/nPIA = 7/3, αSA = 3-5 mol%) into PBT and their anisotropy are better than that of ABS.

scholarly journals Mesh-Type Three-Dimensional (3D) Printing of Human Organs and Tumors: Fast, Cost-Effective, and Personalized Anatomic Modeling of Patient-Oriented Visual Aids

2021 ◽  
Vol 11 (3) ◽  
pp. 1047
Author(s):  
Jungirl Seok ◽  
Sungmin Yoon ◽  
Chang Hwan Ryu ◽  
Junsun Ryu ◽  
Seok-ki Kim ◽  
...  
Keyword(s):  
3D Printing ◽  
3D Modeling ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Tumor Location ◽  
Visual Aids ◽  
Surgical Specimen ◽  
Personalized Care ◽  
Fused Deposition ◽  
Mesh Work

Although three-dimensional (3D)-printed anatomic models are not new to medicine, the high costs and lengthy production times entailed have limited their application. Our goal was developing a new and less costly 3D modeling method to depict organ-tumor relations at faster printing speeds. We have devised a method of 3D modeling using tomographic images. Coordinates are extracted at a specified interval, connecting them to create mesh-work replicas. Adjacent constructs are depicted by density variations, showing anatomic targets (i.e., tumors) in contrasting colors. An array of organ solid-tumor models was printed via a Fused Deposition Modeling 3D printer at significantly less cost ($0.05/cm3) and time expenditure (1.73 min/cm3; both, p < 0.001). Printed models helped promote visual appreciation of organ-tumor anatomy and adjacent tissues. Our mesh-work 3D thyroidal prototype reproduced glandular size/contour and tumor location, readily approximating the surgical specimen. This newly devised mesh-type 3D printing method may facilitate anatomic modeling for personalized care and improve patient awareness during informed surgical consent.

Electromagnetic performance and thermal analysis of a novel permanent magnet fluxed-switching coupler

2021 ◽  
pp. 1-18
Author(s):  
Lezhi Ye ◽  
Yulong Zhang ◽  
Mingguang Cao
Keyword(s):  
Temperature Distribution ◽  
Permanent Magnet ◽  
Permanent Magnets ◽  
Three Dimensional ◽  
Load Condition ◽  
Maximum Load ◽  
Maximum Temperature ◽  
The Novel ◽  
Transient Field ◽  
Three Dimensional Finite Element

To solve the problem of complex operating device and permanent magnets (PMs) demagnetization at high temperature, a new type of permanent magnet fluxed-switching coupler (PMC) with synchronous rotating adjuster is proposed. Its torque can be adjusted by rotating a switched flux angle between the adjuster and PMs along the circumferential direction. The structural feature and working principle of the PMC are introduced. The analytical model of the novel PMC was established. The torque curves are calculated in transient field by using the three-dimensional finite element method (3-D FEM). The temperature distribution of the novel PMC under rated condition is calculated by 3-D FEM, and the temperature distribution of the PM is compared with that of the conventional PMC. The simulation and test results show that the maximum temperature of copper disc and PM of the novel PMC are 100 °C and 48 °C respectively. The novel PMC can work stably for a long time under the maximum load condition.

Development of Scaffold Building Units and Assembly for Tissue Engineering Using Fused Deposition Modelling

2009 ◽  
Vol 83-86 ◽  
pp. 269-274 ◽  
Author(s):  
Syed H. Masood ◽  
Kadhim Alamara
Keyword(s):  
Tissue Engineering ◽  
Pore Size ◽  
Fused Deposition Modeling ◽  
Porous Scaffold ◽  
Cell Structure ◽  
Three Dimensional ◽  
Three Dimensions ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Unit Cells

In tissue engineering (TE), a porous scaffold structure of biodegradable material is required as a template to guide the proliferation, growth and development of cells appropriately in three dimensions. The scaffold must meet design requirements of appropriate porosity, pore size and interconnected structure to allow cell proliferation and adhesion. This paper presents a methodology for design and manufacture of TE scaffolds with varying porosity by employing open structure building units and Fused Deposition Modeling (FDM) rapid prototyping technique. A computer modeling approach for constructing and assembly of three-dimensional unit cell structure is presented to provide a solution of scaffolds design that can potentially meet the diverse requirements of TE applications. A parametric set of open polyhedral unit cells is used to assist the user in designing the required micro-architecture of the scaffold with required porosity and pore size and then the Boolean operation is used to create the scaffold of a given CAD model from the designed microstructure. The procedure is verified by fabrication of physical scaffolds using the commercial FDM system.

Sign in / Sign up

Export Citation Format

Share Document