Conceptual Design for an Industrial Prototype Graz Cycle Power Plant

2002 ◽  
Author(s):  
H. Jericha ◽  
E. Go¨ttlich
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
International Cooperation ◽  
Conceptual Design ◽  
Thermal Efficiency ◽  
Fuel Oil ◽  
Heavy Fuel Oil ◽  
Gasification Products ◽  
Prototype Design ◽  
Industrial Prototype

The gas turbine system GRAZ CYCLE has been thoroughly studied in terms of thermodynamics and turbomachinery layout. What is to be presented here is a prototype design for an industrial size plant, suited for NG-fuel and coal and heavy fuel oil gasification products, capable to retain the CO2 from combustion and at the same time able to achieve maximum thermal efficiency. The authors hope for an international cooperation to make such a plant available within a few years.

Seawater Scrubbing for the Removal of Sulfur Dioxide in a Steam Turbine Power Plant

2005 ◽  
Author(s):  
Akili D. Khawaji ◽  
Jong-Mihn Wie
Keyword(s):  
Power Plant ◽  
Sulfur Dioxide ◽  
Steam Turbine ◽  
Flue Gas ◽  
Operating Cost ◽  
Cooling Water ◽  
Cost Savings ◽  
Fuel Oil ◽  
So2 Emissions ◽  
Heavy Fuel Oil

The most popular method of controlling sulfur dioxide (SO2) emissions in a steam turbine power plant is a flue gas desulfurization (FGD) process that uses lime/limestone scrubbing. Another relatively newer FGD technology is to use seawater as a scrubbing medium to absorb SO2 by utilizing the alkalinity present in seawater. This seawater scrubbing FGD process is viable and attractive when a sufficient quantity of seawater is available as a spent cooling water within reasonable proximity to the FGD scrubber. In this process the SO2 gas in the flue gas is absorbed by seawater in an absorber and subsequently oxidized to sulfate by additional seawater. The benefits of the seawater FGD process over the lime/limestone process and other processes are; 1) The process does not require reagents for scrubbing as only seawater and air are needed, thereby reducing the plant operating cost significantly, and 2) No solid waste and sludge are generated, eliminating waste disposal, resulting in substantial cost savings and increasing plant operating reliability. This paper reviews the thermodynamic aspects of the SO2 and seawater system, basic process principles and chemistry, major unit operations consisting of absorption, oxidation and neutralization, plant operation and performance, cost estimates for a typical seawater FGD plant, and pertinent environmental issues and impacts. In addition, the paper presents the major design features of a seawater FGD scrubber for the 130 MW oil fired steam turbine power plant that is under construction in Madinat Yanbu Al-Sinaiyah, Saudi Arabia. The scrubber with the power plant designed for burning heavy fuel oil containing 4% sulfur by weight, is designed to reduce the SO2 level in flue gas to 425 ng/J from 1,957 ng/J.

scholarly journals A Trade-Off Study of Rotor Tip Clearance Flow in a Turbine/Exhaust Diffuser System

1987 ◽  
Author(s):  
Saeed Farokhi
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Tip Clearance ◽  
Pressure Recovery ◽  
Efficiency Gain ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
Gas Turbine Power Plant

In a modern gas turbine power plant, the axial exhaust diffuser accounts for up to 10% of the generator power. An unshrouded rotor, due to its highly energetic tip clearance flow, improves the pressure recovery characteristic of the exhaust diffuser, while the power production within the blading suffers a loss as a result of the tip leakage flow. In this paper, these conflicting trends are thermodynamically investigated and nondimensional expressions are derived which facilitate the task of a gas turbine system designer. Conservatively, 1% thermal efficiency gain results from elimination of the last rotor tip clearance flow. The corresponding increase in thermal efficiency of a modern gas turbine power plant due to enhanced diffuser pressure recovery is less than one percent.

scholarly journals Thermodynamic analysis of high temperature nuclear reactor coupled with advanced gas turbine combined cycle

2019 ◽  
Vol 23 (Suppl. 4) ◽  
pp. 1187-1197 ◽  
Author(s):  
Marek Jaszczur ◽  
Michal Dudek ◽  
Zygmunt Kolenda
Keyword(s):  
High Temperature ◽  
Power Plant ◽  
Gas Turbine ◽  
Thermodynamic Analysis ◽  
Thermal Efficiency ◽  
Nuclear Power ◽  
Coal Gasification ◽  
Nuclear Reactor ◽  
Combined Cycle ◽  
Oil Processing

One of the most advanced and most effective technology for electricity generation nowadays based on a gas turbine combined cycle. This technology uses natural gas, synthesis gas from the coal gasification or crude oil processing products as the energy carriers but at the same time, gas turbine combined cycle emits SO2, NOx, and CO2 to the environment. In this paper, a thermodynamic analysis of environmentally friendly, high temperature gas nuclear reactor system coupled with gas turbine combined cycle technology has been investigated. The analysed system is one of the most advanced concepts and allows us to produce electricity with the higher thermal efficiency than could be offered by any currently existing nuclear power plant technology. The results show that it is possible to achieve thermal efficiency higher than 50% what is not only more than could be produced by any modern nuclear plant but it is also more than could be offered by traditional (coal or lignite) power plant.

Effect of the Environmental Conditions of Tropical Climates on the Performance Parameters of a Gas Turbine Power Generation Plant

2020 ◽  
Author(s):  
J. Fajardo ◽  
D. Barreto ◽  
T. Castro ◽  
I. Baldiris
Keyword(s):  
Power Plant ◽  
Relative Humidity ◽  
Gas Turbine ◽  
Output Power ◽  
High Temperatures ◽  
Environmental Conditions ◽  
Thermal Efficiency ◽  
Specific Work ◽  
Atmospheric Conditions ◽  
Compressor Inlet

Abstract It is known that high temperatures adversely affect the performance of gas turbines, but the effect of the combination of atmospheric conditions (temperature and relative humidity -RH-) on the operation of this type of system is unknown. In this work the effects of atmospheric conditions on the energy and exergy indicators of a power plant with gas turbine were studied. The indicators studied were the mass flow, the specific work consumed by the compressor, specific work produced by the turbine, the combustion gas temperature, the NO concentration, the net output power, the thermal efficiency, the heat rate, the specific consumption of fuel, the destruction of exergy and exergy efficiency. Among the results, it is noted that for each degree celsius that reduces the temperature of the air at the compressor inlet at constant relative humidity on average, the mass flow of dry air increases by 0.27 kg/s, the specific work consumed by the compressors decreases by 0.45%, the output power increases by 1.17% and the thermal efficiency increases by 0.8%, the exergy destruction increases by 0.72% and the exergy efficiency increases by 0.81%. In addition, humidity changes relative to high temperatures are detected more significantly than at low temperatures. The power plant studied is installed in Cartagena, Colombia and since it is not operating in the design environmental conditions (15 °C and 60% relative humidity) it experiences a loss of output power of 6140 kW and a drop in thermal efficiency of 5.12 %. These results allow considering the implementation of air cooling technologies at the compressor inlet to compensate for the loss of power at atmospheric air conditions.

Enhancing Gas Turbine Operation With Heavy Fuel Oil

2013 ◽  
Author(s):  
Vikram Muralidharan ◽  
Matthieu Vierling
Keyword(s):  
Power Generation ◽  
Natural Gas ◽  
Gas Turbine ◽  
Power Plants ◽  
High Efficiency ◽  
Combined Cycle ◽  
Fuel Oil ◽  
Residual Oil ◽  
Heavy Fuel Oil ◽  
Hydro Power

Power generation in south Asia has witnessed a steep fall due to the shortage of natural gas supplies for power plants and poor water storage in reservoirs for low hydro power generation. Due to the current economic scenario, there is worldwide pressure to secure and make more gas and oil available to support global power needs. With constrained fuel sources and increasing environmental focus, the quest for higher efficiency would be imminent. Natural gas combined cycle plants operate at a very high efficiency, increasing the demand for gas. At the same time, countries may continue to look for alternate fuels such as coal and liquid fuels, including crude and residual oil, to increase energy stability and security. In over the past few decades, the technology for refining crude oil has gone through a significant transformation. With the advanced refining process, there are additional lighter distillates produced from crude that could significantly change the quality of residual oil used for producing heavy fuel. Using poor quality residual fuel in a gas turbine to generate power could have many challenges with regards to availability and efficiency of a gas turbine. The fuel needs to be treated prior to combustion and needs a frequent turbine cleaning to recover the lost performance due to fouling. This paper will discuss GE’s recently developed gas turbine features, including automatic water wash, smart cooldown and model based control (MBC) firing temperature control. These features could significantly increase availability and improve the average performance of heavy fuel oil (HFO). The duration of the gas turbine offline water wash sequence and the rate of output degradation due to fouling can be considerably reduced.

Influence of Steam Injection on Thermal Efficiency and Operating Temperature of GE-F5 Gas Turbines Applying VODOLEY System

2005 ◽  
Author(s):  
Mohsen Ghazikhani ◽  
Nima Manshoori ◽  
Davood Tafazoli
Keyword(s):  
Power Plant ◽  
Ambient Temperature ◽  
Gas Turbine ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Steam Injection ◽  
Gas Turbine Cycle

An industrial gas turbine has the characteristic that turbine output decreases on hot summer days when electricity demand peaks. For GE-F5 gas turbines of Mashad Power Plant when ambient temperature increases 1° C, compressor outlet temperature increases 1.13° C and turbine exhaust temperature increases 2.5° C. Also air mass flow rate decreases about 0.6 kg/sec when ambient temperature increases 1° C, so it is revealed that variations are more due to decreasing in the efficiency of compressor and less due to reduction in mass flow rate of air as ambient temperature increases in constant power output. The cycle efficiency of these GE-F5 gas turbines reduces 3 percent with increasing 50° C of ambient temperature, also the fuel consumption increases as ambient temperature increases for constant turbine work. These are also because of reducing in the compressor efficiency in high temperature ambient. Steam injection in gas turbines is a way to prevent a loss in performance of gas turbines caused by high ambient temperature and has been used for many years. VODOLEY system is a steam injection system, which is known as a self-sufficient one in steam production. The amount of water vapor in combustion products will become regenerated in a contact condenser and after passing through a heat recovery boiler is injected in the transition piece after combustion chamber. In this paper the influence of steam injection in Mashad Power Plant GE-F5 gas turbine parameters, applying VODOLEY system, is being observed. Results show that in this turbine, the turbine inlet temperature (T3) decreases in a range of 5 percent to 11 percent depending on ambient temperature, so the operating parameters in a gas turbine cycle equipped with VODOLEY system in 40° C of ambient temperature is the same as simple gas turbine cycle in 10° C of ambient temperature. Results show that the thermal efficiency increases up to 10 percent, but Back-Work ratio increases in a range of 15 percent to 30 percent. Also results show that although VODOLEY system has water treatment cost but by using this system the running cost will reduce up to 27 percent.

A Study of the Short Range Pollution Around a Power Plant Using Heavy Fuel Oil by Analysing Vanadium in Lichens

1983 ◽  
Vol 15 (1) ◽  
pp. 89-93 ◽  
Author(s):  
S. Nygård ◽  
L. Harju
Keyword(s):  
Power Plant ◽  
Chemical Analysis ◽  
Heavy Oil ◽  
Short Range ◽  
Vanadium Content ◽  
Fuel Oil ◽  
Plasma Emission ◽  
Hypogymnia Physodes ◽  
Heavy Fuel Oil ◽  
Dc Plasma

AbstractThe vanadium content of the lichen Hypogymnia physodes was determined in the vicinity of a power plant using heavy oil as fuel. For the chemical analysis a DC plasma emission spectrometer was used. Air dried samplesof the lichen contained between 1–4 and 57 parts per million (ppm) of vanadium. The highest concentrations were found in specimens collected less than 1 km from the power plant. Lichens collected 50 km from the plant contained less than 2 ppm of vanadium.

Conceptual Design and Cooling Blade Development of 1700°C Class High-Temperature Gas Turbine

2005 ◽  
Vol 127 (2) ◽  
pp. 358-368 ◽  
Author(s):  
Shoko Ito ◽  
Hiroshi Saeki ◽  
Asako Inomata ◽  
Fumio Ootomo ◽  
Katsuya Yamashita ◽  
...  
Keyword(s):  
Heat Transfer ◽  
High Temperature ◽  
Gas Turbine ◽  
Conceptual Design ◽  
Thermal Efficiency ◽  
Internal Cooling ◽  
Closed Cycle ◽  
Steam Consumption ◽  
Flow Phenomena ◽  
High Temperature Gas

In this paper we describe the conceptual design and cooling blade development of a 1700°C-class high-temperature gas turbine in the ACRO-GT-2000 (Advanced Carbon Dioxide Recovery System of Closed-Cycle Gas Turbine Aiming 2000 K) project. In the ACRO-GT closed cycle power plant system, the thermal efficiency aimed at is more than 60% of the higher heating value of fuel (HHV). Because of the high thermal efficiency requirement, the 1700°C-class high-temperature gas turbine must be designed with the minimum amount of cooling and seal steam consumption. The hybrid cooling scheme, which is a combination of closed loop internal cooling and film ejection cooling, was chosen from among several cooling schemes. The elemental experiments and numerical studies, such as those on blade surface heat transfer, internal cooling channel heat transfer, and pressure loss and rotor coolant passage distribution flow phenomena, were conducted and the results were applied to the conceptual design advancement. As a result, the cooling steam consumption in the first stage nozzle and blade was reduced by about 40% compared with the previous design that was performed in the WE-NET (World Energy Network) Phase-I.

Development of Key Technologies for the Next Generation High Temperature Gas Turbine

2011 ◽  
Author(s):  
Eisaku Ito ◽  
Ikuo Okada ◽  
Keizo Tsukagoshi ◽  
Junichiro Masada
Keyword(s):  
Global Warming ◽  
High Temperature ◽  
Power Plant ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Reducing Power ◽  
Combined Cycle ◽  
National Project ◽  
Key Technologies ◽  
High Temperature Gas

Global warming is being “prevented” by reducing power plant CO2 emissions. We are contributing to the overall solution by improving the gas turbine thermal efficiency for gas turbine combined cycle (GTCC). Mitsubishi Heavy Industries, Ltd. (MHI) is a participant in a national project aimed at developing 1700°C gas turbine technology. As part of this national project, selected component technologies are investigated in detail. Some technologies which have been verified through component tests have been applied to the design of the newly developed 1600°C J-type gas turbine.

Outline of Plan for Advanced Reheat Gas Turbine

1981 ◽  
Vol 103 (4) ◽  
pp. 772-775 ◽  
Author(s):  
Akifumi Hori ◽  
Kazuo Takeya
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Axial Flow ◽  
Combined Cycle ◽  
Research Association ◽  
Major Objective ◽  
Engineering Research ◽  
Set Up

A new reheat gas turbine system is being developed as a national project by the “Engineering Research Association for Advanced Gas Turbines” of Japan. The machine consists of two axial flow compressors, three turbines, intercooler, combustor and reheater. The pilot plant is expected to go into operation in 1982, and a prototype plant will be set up in 1984. The major objective of this reheat gas turbine is application to a combined cycle power plant, with LNG burning, and the final target of combined cycle thermal efficiency is to be 55 percent (LHV).

Sign in / Sign up

Export Citation Format

Share Document