Effects of Flow Injection From Outer Casing Upon Turbine Nozzle Vane Flow Field

2002 ◽  
Author(s):  
K. Funazaki ◽  
C. F. F. Favaretto ◽  
T. Tanuma
Keyword(s):  
Flow Field ◽  
Flow Injection ◽  
Three Dimensional ◽  
Leading Edge ◽  
Main Stream ◽  
Flow Angle ◽  
Aerodynamic Loss ◽  
Nozzle Vane ◽  
Design Variables ◽  
The Impact

In the present paper steady three-dimensional numerical calculations were performed in order to investigate the effects of flow injection from the outer casing upon turbine nozzle vane flow field. Several test cases were analyzed by applying different nozzle vane configurations such as the blade lean, injection slot width and distance from the leading edge. Numerical simulations were conducted considering the no injection case, 5% and 10% main stream flow injection from the outer casing. The impact of the flow injection design variables and the blade lean angle on the aerodynamic loss in terms of the energy loss coefficient and the outlet flow angle were analyzed through a parametric study.

Effects of Inlet Distortion on the Flow Field in a Transonic Compressor Rotor

1996 ◽  
Author(s):  
Chunill Hah ◽  
Douglas C. Rabe ◽  
Thomas J. Sullivan ◽  
Aspi R. Wadia
Keyword(s):  
Boundary Layer ◽  
Flow Field ◽  
Viscous Flow ◽  
Total Pressure ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Aerodynamic Loss ◽  
Transonic Compressor ◽  
Inlet Distortion ◽  
Compressor Rotor

The effects of circumferential distortions in inlet total pressure on the flow field in a low-aspect-ratio, high-speed, high-pressure-ratio, transonic compressor rotor are investigated in this paper. The flow field was studied experimentally and numerically with and without inlet total pressure distortion. Total pressure distortion was created by screens mounted upstream from the rotor inlet. Circumferential distortions of 8 periods per revolution were investigated at two different rotor speeds. The unsteady blade surface pressures were measured with miniature pressure transducers mounted in the blade. The flow fields with and without inlet total pressure distortion were analyzed numerically by solving steady and unsteady forms of the Reynolds-averaged Navier-Stokes equations. Steady three-dimensional viscous flow calculations were performed for the flow without inlet distortion while unsteady three-dimensional viscous flow calculations were used for the flow with inlet distortion. For the time-accurate calculation, circumferential and radial variations of the inlet total pressure were used as a time-dependent inflow boundary condition. A second-order implicit scheme was used for the time integration. The experimental measurements and the numerical analysis are highly complementary for this study because of the extreme complexity of the flow field. The current investigation shows that inlet flow distortions travel through the rotor blade passage and are convected into the following stator. At a high rotor speed where the flow is transonic, the passage shock was found to oscillate by as much as 20% of the blade chord, and very strong interactions between the unsteady passage shock and the blade boundary layer were observed. This interaction increases the effective blockage of the passage, resulting in an increased aerodynamic loss and a reduced stall margin. The strong interaction between the passage shock and the blade boundary layer increases the peak aerodynamic loss by about one percent.

Experimental Studies of Leading Edge Contouring Influence on Secondary Losses in Transonic Turbines

2012 ◽  
Author(s):  
Ranjan Saha ◽  
Jens Fridh ◽  
Torsten Fransson ◽  
Boris I. Mamaev ◽  
Mats Annerfeldt
Keyword(s):  
Gas Turbine ◽  
Guide Vane ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Leading Edge ◽  
Secondary Flows ◽  
Noticeable Effect ◽  
Flow Angle ◽  
Wide Range ◽  
Contour Plots

An experimental study of the hub leading edge contouring using fillets is performed in an annular sector cascade to observe the influence of secondary flows and aerodynamic losses. The investigated vane is a three dimensional gas turbine guide vane (geometrically similar) with a mid-span aspect ratio of 0.46. The measurements are carried out on the leading edge fillet and baseline cases using pneumatic probes. Significant precautions have been taken to increase the accuracy of the measurements. The investigations are performed for a wide range of operating exit Mach numbers from 0.5 to 0.9 at a design inlet flow angle of 90°. Data presented include the loading, fields of total pressures, exit flow angles, radial flow angles, as well as profile and secondary losses. The vane has a small profile loss of approximately 2.5% and secondary loss of about 1.1%. Contour plots of vorticity distributions and velocity vectors indicate there is a small influence of the vortex-structure in endwall regions when the leading edge fillet is used. Compared to the baseline case the loss for the filleted case is lower up to 13% of span and higher from 13% to 20% of the span for a reference condition with Mach no. of 0.9. For the filleted case, there is a small increase of turning up to 15% of the span and then a small decrease up to 35% of the span. Hence, there are no significant influences on the losses and turning for the filleted case. Results lead to the conclusion that one cannot expect a noticeable effect of leading edge contouring on the aerodynamic efficiency for the investigated 1st stage vane of a modern gas turbine.

Influence of different blade numbers on the performance of “saddle zone” in a mixed flow pump

2021 ◽  
pp. 095765092110460
Author(s):  
Leilei Ji ◽  
Wei Li ◽  
Weidong Shi ◽  
Fei Tian ◽  
Shuo Li ◽  
...  
Keyword(s):  
Flow Field ◽  
Leading Edge ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Mixed Flow ◽  
Impeller Blade ◽  
Flow Angle ◽  
Tip Leakage ◽  
Vorticity Transport ◽  
Flow Pump

In order to study the effect of different numbers of impeller blades on the performance of mixed-flow pump “saddle zone”, the external characteristic test and numerical simulation of mixed-flow pumps with three different impeller blade numbers were carried out. Based on high-precision numerical prediction, the internal flow field and tip leakage flow field of mixed flow pump under design conditions and stall conditions are investigated. By studying the vorticity transport in the stall flow field, the specific location of the high loss area inside the mixed flow pump impeller with different numbers of blades is located. The research results show that the increase in the number of impeller blades improve the pump head and efficiency under design conditions. Compared to the 4-blade impeller, the head and efficiency of the 5-blade impeller are increased by 5.4% and 21.9% respectively. However, the increase in the number of blades also leads to the widening of the “saddle area” of the mixed-flow pump, which leads to the early occurrence of stall and increases the instability of the mixed-flow pump. As the mixed-flow pump enters the stall condition, the inlet of the mixed-flow pump has a spiral swirl structure near the end wall for different blade numbers, but the depth and range of the swirling flow are different due to the change in the number of blades. At the same time, the change in the number of blades also makes the flow angle at 75% span change significantly, but the flow angle at 95% span is not much different because the tip leakage flow recirculates at the leading edge. Through the analysis of the vorticity transport results in the impeller with different numbers of blades, it is found that the reasons for the increase in the values of the vorticity transport in the stall condition are mainly impacted by the swirl flow at the impeller inlet, the tip leakage flow at the leading edge and the increased unsteady flow structures.

Three Dimensional Clocking Effects in a One and a Half Stage Transonic Turbine

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
O. Schennach ◽  
J. Woisetschläger ◽  
B. Paradiso ◽  
G. Persico ◽  
P. Gaetani
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Fast Response ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Time Resolved ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Velocity Flow ◽  
Transonic Turbine

This paper presents an experimental investigation of the flow field in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine) concerning the airfoil indexing. The objective is a detailed analysis of the three-dimensional aerodynamics of the second vane for different clocking positions. To give an overview of the time-averaged flow field, five-hole probe measurements were performed upstream and downstream of the second stator. Furthermore in these planes additional unsteady measurements were carried out with laser Doppler velocimetry in order to record rotor phase-resolved velocity, flow angle, and turbulence distributions at two different clocking positions. In the planes upstream of the second vane, the time-resolved pressure field has been measured by means of a fast response aerodynamic pressure probe. This paper shows that the secondary flows of the second vane are significantly modified by the different clocking positions, in connection with the first vane modulation of the rotor secondary flows. An analysis of the performance of the second vane is also carried out, and a 0.6% variation in the second vane loss coefficient has been recorded among the different clocking positions.

Numerical and Experimental Investigation of Return Channel Vane Aerodynamics With Two-Dimensional and Three-Dimensional Vanes

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
A. Hildebrandt ◽  
F. Schilling
Keyword(s):  
Experimental Investigation ◽  
Flow Field ◽  
Static Pressure ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Field Performance ◽  
Two Dimensional ◽  
Flow Angle ◽  
Overall Performance ◽  
Return Channel

The present paper deals with the numerical and experimental investigation of the effect of return channel (RCH) dimensions of a centrifugal compressor stage on the aerodynamic performance. Three different return channel stages were investigated, two stages comprising three-dimensional (3D) return channel blades and one stage comprising two-dimensional (2D) RCH vanes. The analysis was performed regarding both the investigation of overall performance (stage efficiency, RCH total pressure loss coefficient) and detailed flow-field performance. For detailed experimental flow-field investigation at the stage exit, six circumferentially traversed three-hole probes were positioned downstream the return channel exit in order to get two-dimensional flow-field information. Additionally, static pressure wall measurements were taken at the hub and shroud pressure and suction side (SS) of the 2D and 3D return channel blades. The return channel system overall performance was calculated by measurements of the circumferentially averaged 1D flow field downstream the diffuser exit and downstream the stage exit. Dependent on the type of return channel blade, the numerical and experimental results show a significant effect on the flow field overall and detail performance. In general, satisfactory agreement between computational fluid dynamics (CFD)-prediction and test-rig measurements was achieved regarding overall and flow-field performance. In comparison with the measurements, the CFD-calculated stage performance (efficiency and pressure rise coefficient) of all the 3D-RCH stages was slightly overpredicted. Very good agreement between CFD and measurement results was found for the static pressure distribution on the RCH wall surfaces while small CFD-deviations occur in the measured flow angle at the stage exit, dependent on the turbulence model selected.

HP Vane Aerodynamics and Heat Transfer in the Presence of Aggressive Inlet Swirl

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
Imran Qureshi ◽  
Andy D. Smith ◽  
Thomas Povey
Keyword(s):  
Heat Transfer ◽  
Cooling System ◽  
Three Dimensional ◽  
Leading Edge ◽  
Good Deal ◽  
Vortex Center ◽  
Research Facility ◽  
Lean Burn ◽  
Numerical Predictions ◽  
The Impact

Modern lean burn combustors now employ aggressive swirlers to enhance fuel-air mixing and improve flame stability. The flow at combustor exit can therefore have high residual swirl. A good deal of research concerning the flow within the combustor is available in open literature. The impact of swirl on the aerodynamic and heat transfer characteristics of an HP turbine stage is not well understood, however. A combustor swirl simulator has been designed and commissioned in the Oxford Turbine Research Facility (OTRF), previously located at QinetiQ, Farnborough UK. The swirl simulator is capable of generating an engine-representative combustor exit swirl pattern. At the turbine inlet plane, yaw and pitch angles of over ±40 deg have been simulated. The turbine research facility used for the study is an engine scale, short duration, rotating transonic turbine, in which the nondimensional parameters for aerodynamics and heat transfer are matched to engine conditions. The research turbine was the unshrouded MT1 design. By design, the center of the vortex from the swirl simulator can be clocked to any circumferential position with respect to HP vane, and the vortex-to-vane count ratio is 1:2. For the current investigation, the clocking position was such that the vortex center was aligned with the vane leading edge (every second vane). Both the aligned vane and the adjacent vane were characterized. This paper presents measurements of HP vane surface and end wall heat transfer for the two vane positions. The results are compared with measurements conducted without swirl. The vane surface pressure distributions are also presented. The experimental measurements are compared with full-stage three-dimensional unsteady numerical predictions obtained using the Rolls Royce in-house code Hydra. The aerodynamic and heat transfer characterization presented in this paper is the first of its kind, and it is hoped to give some insight into the significant changes in the vane flow and heat transfer that occur in the current generation of low NOx combustors. The findings not only have implications for the vane aerodynamic design, but also for the cooling system design.

Numerical study of the impact of water injection holes arrangement on cavitation flow control

2019 ◽  
Vol 103 (1) ◽  
pp. 003685041987774 ◽  
Author(s):  
Wei Wang ◽  
Qingdian Zhang ◽  
Tao Tang ◽  
Shengpeng Lu ◽  
Qi Yi ◽  
...  
Keyword(s):  
Flow Field ◽  
Numerical Study ◽  
Water Injection ◽  
Three Dimensional ◽  
Hydrodynamic Performance ◽  
Cavitation Flow ◽  
Suction Surface ◽  
Double Row ◽  
Suppression Effect ◽  
The Impact

A method of water injection to flow field using distributed holes on the suction surface of hydrofoil is presented in this article to control cavitation flow. Modified renormalization group k–ε turbulence model is coupled with full-cavitation model to calculate periodical cavitation patterns and the dynamic characteristics of the NACA66(MOD) hydrofoil. Water injection is found to be highly effective for cavitation suppression. The cavitation suppression effect of distributed regulation of jet holes and porosities along three-dimensional spanwise hydrofoil is also investigated. The appropriate porosities of single row spanwise jet holes and optimal jet position of double row jet holes are revealed for both cavitation suppression and good hydrodynamic performance. Double row jet holes setting in forward trapezoidal arrangement shows great potential for cavitation suppression and hydrodynamic performance. This research provides a method of water injection to flow field to actively control cavitation, which will facilitate development of engineering designs.

The effect analysis of an engine jet on an aircraft blast deflector

2018 ◽  
Vol 41 (4) ◽  
pp. 990-1001
Author(s):  
Song Ma ◽  
Jianguo Tan ◽  
Xiankai Li ◽  
Jiang Hao
Keyword(s):  
High Temperature ◽  
Flow Field ◽  
High Speed ◽  
Deflection Angle ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Aircraft Engine ◽  
Experimental Results ◽  
Exhaust Gases ◽  
The Impact

This paper establishes a novel mathematical model for computing the plume flow field of a carrier-based aircraft engine. Its objective is to study the impact of jet exhaust gases with high temperature, high speed and high pressure on the jet blast deflector. The working condition of the nozzle of a fully powered on engine is first determined. The flow field of the exhaust jet is then numerically simulated at different deflection angle using the three-dimensional Reynolds averaged Navier–Stokes equations and the standard [Formula: see text]-[Formula: see text] turbulence method. Moreover, infra-red temperature tests are further carried out to test the temperature field when the jet blast deflector is at the [Formula: see text] deflection angle. The comparison between the simulation results and the experimental results show that the proposed computation model can perfectly describe the system. There is only 8–10% variation between them. A good verification is achieved. Moreover, the experimental results show that the jet blast deflector plays an outstanding role in driving the high-temperature exhaust gases. It is found that [Formula: see text] may be the best deflection angle to protect the deck and the surrounding equipment effectively. These data results provide a valuable basis for the design and layout optimization of the jet blast deflector and deck.

Experimental and Numerical Investigation of the Unsteady Leakage Flow Through the Rotor Tip Labyrinth of a 1.5-Stage Axial Turbine

2005 ◽  
Author(s):  
K. Wolter ◽  
A. Giboni ◽  
P. Peters ◽  
J. R. Menter ◽  
H. Pfost
Keyword(s):  
Flow Field ◽  
Flow Direction ◽  
Three Dimensional ◽  
Calculated Data ◽  
Leading Edge ◽  
Numerical Data ◽  
Potential Effect ◽  
Main Flow ◽  
Leakage Flow ◽  
Axial Turbine

This paper presents the results of unsteady probe measurements and numerical flow calculations in a 1.5-stage low speed axial turbine with a straight labyrinth seal on a rotor shroud. The unsteady development of the leakage flow in the three cavities is described and analysed in detail. For the investigation of the leakage flow detailed time-accurate measurements of the three-dimensional flow field were carried out in five measurement planes from casing to the rotor shroud over more than one pitch. These measurements were carried out with a miniature pneumatic five-hole probe and miniature triple hot-wire probes. Both probes have a spherical head for better adjustment in flow direction. The high resolution of 330 measurement points in each of the five measurement planes represents the flow field in great detail. The unsteady experimental data was compared with the results of the unsteady numerical simulation of the turbine flow, calculated by the 3D-Navier-Stokes Solver CFX-TASCflow. The calculated data correspond well with the experimental results and allow a detailed analysis of the flow in the cavities of the labyrinth. As demonstrated in this paper the investigations show that the leakage flow at the inlet ant outlet of the labyrinth is strongly influenced by the different positions of the rotor to the stator. The unsteady experimental and numerical data indicates intensive effects of the leakage flow caused and influenced by the trailing edge of the first stator and the potential effect of the rotor leading edge. An intensive vortex develops depending on the rotor position in the first cavity. This vortex is also influenced by a small corner vortex above the axial inlet gap of the labyrinth. After the fins this unsteady influence of the leakage flow decreases and below the jet a large vortex moves in circumferential direction. The intensity of this circulation vortex is reduced at the end of the last cavity due to the interaction with the main flow and the flow direction out of the labyrinth. Therefore the unsteady behaviour of the leakage flow grows up, which is also caused by its uneven entry into the main flow.

An Impact of Various Shroud Bleed Slot Configurations and Cavity Vanes on Compressor Map Width and the Inducer Flow Field

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Subenuka Sivagnanasundaram ◽  
Stephen Spence ◽  
Juliana Early ◽  
Bahram Nikpour
Keyword(s):  
Flow Field ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Operating Conditions ◽  
Choked Flow ◽  
Recirculating Flow ◽  
Heavy Duty Diesel ◽  
Compressor Map ◽  
The Impact

This paper describes an investigation of map width enhancement and a detailed analysis of the inducer flow field due to various bleed slot configurations and vanes in the annular cavity of a turbocharger centrifugal compressor. The compressor under investigation is used in a turbocharger application for a heavy duty diesel engine of approximately 400 hp. This investigation has been undertaken using a computational fluid dynamics (CFD) model of the full compressor stage, which includes a manual multiblock-structured grid generation method. The influence of the bleed slot flow on the inducer flow field at a range of operating conditions has been analyzed, highlighting the improvement in surge and choked flow capability. The impact of the bleed slot geometry variations and the inclusion of cavity vanes on the inlet incidence angle have been studied in detail by considering the swirl component introduced at the leading edge by the recirculating flow through the slot. Further, the overall stage efficiency and the nonuniform flow field at the inducer inlet have been also analyzed. The analysis revealed that increasing the slot width has increased the map width by about 17%. However, it has a small impact on the efficiency, due to the frictional and mixing losses. Moreover, adding vanes in the cavity improved the pressure ratio and compressor performance noticeably. A detail analysis of the compressor with cavity vanes has also been presented.

Sign in / Sign up

Export Citation Format

Share Document