Performance Analysis of Cogenerative and Trigenerative Plant With Microgas-Turbine

2012 ◽  
Author(s):  
Caterina Brandoni ◽  
Gabriele Comodi ◽  
Leonardo Pelagalli ◽  
Flavio Caresana
Keyword(s):  
Experimental Data ◽  
Economic Evaluation ◽  
Performance Analysis ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Hot Water ◽  
Application Range ◽  
Micro Gas Turbine ◽  
The Core ◽  
Single Effect

The paper reports on the performance analysis of cogenerative and trigenerative plants based on Micro Gas Turbines. The core of the system is a natural-gas-fuelled Turbec T100 operating on a regenerated open-air cycle. A code specifically developed by the authors to simulate the micro gas turbine in cogeneration plants, and already checked against experimental data, has been upgraded to simulate the unit’s behavior when facing also a cooling demand (trigenerative case). For this purpose the model of a water-LiBr single-effect absorption chiller driven by hot water has been used. The analysis cover all the unit’s application range and represent a start for its economic evaluation.

scholarly journals Thermodynamic Analysis and Process System Comparison of the Exhaust Gas Recirculated, Steam Injected and Humidified Micro Gas Turbine

2015 ◽  
Author(s):  
Usman Ali ◽  
Carolina Font Palma ◽  
Kevin J. Hughes ◽  
Derek B. Ingham ◽  
Lin Ma ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Co2 Enrichment ◽  
Hot Water ◽  
Exhaust Gas ◽  
Electrical Efficiency ◽  
Micro Gas Turbine ◽  
Carbon Dioxide Co2 ◽  
Reduction Of Co2 ◽  
The Impact

Stringent environmental emission regulations and continuing efforts to reduce carbon dioxide (CO2) from the energy sector, in the context of global warming, have promoted interest to improve the efficiency of power generation systems whilst reducing emissions. Further, this has led to the development of innovative gas turbine systems which either result in higher electrical efficiency or the reduction of CO2 emissions. Micro gas turbines are one of the secure, economical and environmentally viable options for power and heat generation. Here, a Turbec T100 micro gas turbine (MGT) is simulated using Aspen HYSYS® V8.4 and validated through experimental data. Due to the consistency and robustness of the steady state model developed, it is further extended to three different innovative cycles: (i) an exhaust gas recirculated (EGR) cycle, in which part of the exhaust gas is dried and re-circulated to the MGT inlet; (ii) a steam injected (STIG) cycle, and (iii) a humid air turbine (HAT) cycle. The steam and hot water are generated through the exhaust of the recuperator for the STIG and HAT cycle, respectively. Further, the steam is directly injected into the recuperator for power augmentation, while for the HAT cycle; the compressed air is saturated with water in the humid tower before entering the recuperator. This study evaluates the impact of the EGR ratio, steam to air ratio, and water to air ratio on the performance and efficiency of the system. The comparative potential for each innovative cycle is assessed by thermodynamic properties estimation of process parameters through the models developed to better understand the behavior of each cycle. The thermodynamic assessment indicates that CO2 enrichment occurs for the three innovative cycles. Further, the results indicate that the electrical efficiency increases for the STIG and HAT cycle while it decreases for the EGR cycle. In conclusion, the innovative cycles indicates the possibilities to improve the system performance and efficiency.

Numerical Investigation of an Inverted Brayton Cycle Micro Gas Turbine Based on Experimental Data

2018 ◽  
Author(s):  
Eleni Agelidou ◽  
Martin Henke ◽  
Thomas Monz ◽  
Manfred Aigner
Keyword(s):  
Experimental Data ◽  
Power Systems ◽  
Gas Turbine ◽  
Residential Buildings ◽  
Pollutant Emissions ◽  
Brayton Cycle ◽  
Single Family ◽  
Total Energy Consumption ◽  
Gas Treatment ◽  
Micro Gas Turbine

Residential buildings account for approximately one fifth of the total energy consumption and 12 % of the overall CO2 emissions in the OECD countries. Replacing conventional boilers by a co-generation of heat and power in decentralized plants on site promises a great benefit. Especially, micro gas turbine (MGT) based combined heat and power systems are particularly suitable due to their low pollutant emissions without exhaust gas treatment. Hence, the overall aim of this work is the development of a recuperated inverted MGT as heat and power supply for a single family house with 1 kWel. First, an inverted MGT on a Brayton cycle MGT was developed and experimentally characterized, in previous work by the authors. This approach allows exploiting the potential of using the same components for both cycles. As a next step, the applicability of the Brayton cycle components operated in inverted mode needs to be evaluated and the requirements for a component optimization need to be defined, both, by pursuing thermodynamic cycle simulations. This paper presents a parametrization and validation of in-house 1D steady state simulation tool for an inverted MGT, based on experimental data from the inverted Brayton cycle test rig. Moreover, a sensitivity analysis is conducted to estimate the influence of every major component on the overall system and to identify the necessary optimizations. Finally, the component requirements for an optimized inverted MGT with 1 kWel and 16 % of electrical efficiency are defined. This work demonstrates the high potential of an inverted MGT for a decentralized heat and power generation when optimizing the system components.

Assessment of the Potential of Combined Micro Gas Turbine and High Temperature Fuel Cell Systems

2002 ◽  
Author(s):  
Dieter Bohn ◽  
Nathalie Po¨ppe ◽  
Joachim Lepers
Keyword(s):  
Fuel Cells ◽  
High Temperature ◽  
Fuel Cell ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Advanced Materials ◽  
Cell Systems ◽  
Micro Gas Turbine ◽  
Technological Assessment

The present paper reports a detailed technological assessment of two concepts of integrated micro gas turbine and high temperature (SOFC) fuel cell systems. The first concept is the coupling of micro gas turbines and fuel cells with heat exchangers, maximising availability of each component by the option for easy stand-alone operation. The second concept considers a direct coupling of both components and a pressurised operation of the fuel cell, yielding additional efficiency augmentation. Based on state-of-the-art technology of micro gas turbines and solid oxide fuel cells, the paper analyses effects of advanced cycle parameters based on future material improvements on the performance of 300–400 kW combined micro gas turbine and fuel cell power plants. Results show a major potential for future increase of net efficiencies of such power plants utilising advanced materials yet to be developed. For small sized plants under consideration, potential net efficiencies around 70% were determined. This implies possible power-to-heat-ratios around 9.1 being a basis for efficient utilisation of this technology in decentralised CHP applications.

scholarly journals Thermodynamic modelling and efficiency analysis of a class of real indirectly fired gas turbine cycles

2009 ◽  
Vol 13 (4) ◽  
pp. 41-48
Author(s):  
Zheshu Ma ◽  
Zhenhuan Zhu
Keyword(s):  
High Temperature ◽  
Heat Exchanger ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Waste Heat ◽  
Operational Parameters ◽  
Forecast Performance ◽  
Micro Gas Turbine ◽  
Temperature Heat

Indirectly or externally-fired gas-turbines (IFGT or EFGT) are novel technology under development for small and medium scale combined power and heat supplies in combination with micro gas turbine technologies mainly for the utilization of the waste heat from the turbine in a recuperative process and the possibility of burning biomass or 'dirty' fuel by employing a high temperature heat exchanger to avoid the combustion gases passing through the turbine. In this paper, by assuming that all fluid friction losses in the compressor and turbine are quantified by a corresponding isentropic efficiency and all global irreversibilities in the high temperature heat exchanger are taken into account by an effective efficiency, a one dimensional model including power output and cycle efficiency formulation is derived for a class of real IFGT cycles. To illustrate and analyze the effect of operational parameters on IFGT efficiency, detailed numerical analysis and figures are produced. The results summarized by figures show that IFGT cycles are most efficient under low compression ratio ranges (3.0-6.0) and fit for low power output circumstances integrating with micro gas turbine technology. The model derived can be used to analyze and forecast performance of real IFGT configurations.

Experimental and numerical study of flame structure and emissions in a micro gas turbine combustor

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Vedant Dwivedi ◽  
Srikanth Hari ◽  
S. M. Kumaran ◽  
B. V. S. S. S. Prasad ◽  
Vasudevan Raghavan
Keyword(s):  
Gas Turbine ◽  
Rural Areas ◽  
Gas Turbines ◽  
Alternative Fuels ◽  
Numerical Study ◽  
Operating Conditions ◽  
Emission Characteristics ◽  
Nitric Oxides ◽  
Gas Turbine Combustor ◽  
Micro Gas Turbine

Abstract Experimental and numerical study of flame and emission characteristics in a tubular micro gas turbine combustor is reported. Micro gas turbines are used for distributed power (DP) generation using alternative fuels in rural areas. The combustion and emission characteristics from the combustor have to be studied for proper design using different fuel types. In this study methane, representing fossil natural gas, and biogas, a renewable fuel that is a mixture of methane and carbon-dioxide, are used. Primary air flow (with swirl component) and secondary aeration have been varied. Experiments have been conducted to measure the exit temperatures. Turbulent reactive flow model is used to simulate the methane and biogas flames. Numerical results are validated against the experimental data. Parametric studies to reveal the effects of primary flow, secondary flow and swirl have been conducted and results are systematically presented. An analysis of nitric-oxides emission for different fuels and operating conditions has been presented subsequently.

A methodology for identifying the most suitable measurements for engine level and component level gas path diagnostics of a micro gas turbine

2021 ◽  
pp. 095440622110303
Author(s):  
SS Talebi ◽  
AM Tousi ◽  
A Madadi ◽  
M Kiaee
Keyword(s):  
Path Analysis ◽  
Gas Turbine ◽  
Smart Grids ◽  
Gas Turbines ◽  
Complex Dynamics ◽  
Gas Temperature ◽  
Component Level ◽  
Part Load ◽  
Micro Gas Turbine ◽  
Process Gas

Recently, the utilization of micro gas turbines in smart grids are rising that makes the part-load operation principal situation of the engine service. This leads to faster life consumption that increases the importance of the diagnostics process. Gas path analysis is an effective method for gas turbine diagnostics. Complex dynamics of gas turbine induces challenging conditions to perform applicable gas path analysis. This study aims to facilitate MGT gas path diagnostics through reducing the number of monitoring parameters and preparation a pattern for engine level and component level health assessment in both full and part load operation of a recuperated micro gas turbine. To attain this goal a model is proposed to simulate MGT off-design performance which is validated against experimental data in healthy and degraded operation modes. Fouling in compressor, turbine and recuperator and erosion in compressor and turbine as the most common degradations in the gas turbine are considered. The fault simulation is performed by changing the health parameters of gas path components. According to the result investigation, a matrix comprises deviation contours of four parameters, Power, fuel flow, compressor discharge pressure, and exhaust gas temperature is presented and analyzed. The analysis shows that monitoring these parameters makes it possible to perform engine level and component level diagnostics through evaluating a binary code (generated by mentioned parameter variations) against the fault effects pattern in different load fractions and fault severities. The simulation also showed that the most power drop occurred under the compressor fouling by about 8.7% while the most reduction in thermal efficiency is observed under recuperator fouling by about 7.84%. Furthermore, the investigation showed the maximum decrease in the surge margin induced by the compressor fouling during the lower part-load operation by about 45.7% while in the higher loads created by the turbine fouling by about 14%.

Micro Gas Turbine With Ceramic Nozzle and Rotor

2005 ◽  
Author(s):  
Takayuki Matsunuma ◽  
Hiro Yoshida ◽  
Norihiko Iki ◽  
Takumi Ebara ◽  
Satoshi Sodeoka ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Rotor ◽  
Total Power ◽  
Inlet Temperature ◽  
Present System ◽  
Outlet Temperature ◽  
Micro Gas Turbine ◽  
Buffer Material ◽  
Inconel 713C

A series of operation tests of a ceramic micro gas turbine has been successfully carried out. The baseline machine is a small single-shaft turbojet engine (J-850, Sophia Precision Corp.) with a centrifugal compressor, an annular type combustor, and a radial turbine. As a first step, an Inconel 713C alloy turbine rotor of 55 mm in diameter was replaced with a ceramic rotor (SN-235, Kyocera Corporation). A running test was conducted at rotational speeds of up to 140,000 rpm in atmospheric air. At this rotor speed, the compression pressure ratio and the thrust were 3 and 100 N, respectively. The total energy level (enthalpy and kinetic energy) of the exhaust gas jet was 240 kW. If, for example, it is assumed that 10% of the total power of the exhaust jet gas was converted into electricity, the present system would correspond to a generator with 24 kW output power. The measured turbine outlet temperature was 950°C (1,740°F) and the turbine inlet temperature was estimated to be 1,280°C (2,340°F). Although the ceramic rotor showed no evidence of degradation, the Inconel nozzle immediately in front of the turbine rotor partially melted in this rotor condition. As a second step, the Inconel turbine nozzle and casing were replaced with ceramic parts (SN-01, Ohtsuka Ceramics Inc.). The ceramic nozzle and case were supported by metal parts. Through tests with the ceramic nozzle, it became evident that one of the key technologies for the development of ceramic gas turbines is the design of the interface between the ceramic components and the metallic components, because the difference between the coefficients of linear thermal expansion of the ceramic and metal produces large thermal stress at their interface in the high-temperature condition. A buffer material made of alumina fiber was therefore introduced at the interface between the ceramic and metal.

Sign in / Sign up

Export Citation Format

Share Document