Performance and Emissions Characteristics Investigation of a Bi-Fuel SI Engine Fuelled by CNG and Gasoline

2006 ◽  
Author(s):  
Abazar Shamekhi ◽  
Nima Khatibzadeh ◽  
Amir H. Shamekhi
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Engine Performance ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Engine Fuel ◽  
Wide Range ◽  
Performance And Emissions ◽  
Pollutant Sources

Nowadays, increased attention has been focused on internal combustion engine fuels. Regarding environmental effects of internal combustion engines particularly as pollutant sources and depletion of fossil fuel resources, compressed natural gas (CNG) has been introduced as an effective alternative to gasoline and diesel fuel in many applications. A high research octane number allows combustion at higher compression ratios without knocking and good emission characteristics of HC and CO are major benefits of CNG as an engine fuel. In this paper, CNG as an alternative fuel in a spark ignition engine has been considered. Engine performance and exhaust emissions have been experimentally studied for CNG and gasoline in a wide range of the engine operating conditions.

scholarly journals Unambiguous Identification of Key Molecular Species in Deposits Responsible for Increased Pollution from Internal Combustion Engines

2020 ◽  
Author(s):  
Max K. Edney ◽  
Joseph S. Lamb ◽  
Matteo Spanu ◽  
Emily F. Smith ◽  
Elisabeth Steer ◽  
...  
Keyword(s):  
Spatial Distribution ◽  
Molecular Species ◽  
Internal Combustion Engines ◽  
Fuel Cycle ◽  
Combustion Engine ◽  
Engine Performance ◽  
Internal Combustion ◽  
Energy System ◽  
Pollutant Emissions ◽  
Engine Fuel

<p>Clean and efficient internal combustion engine performance will play a significant role in the move to a decarbonized energy system. Currently, fuel deposit formation on engine components negatively impacts CO2 and pollutant emissions, where previous attempts at deposit characterization afforded non-diagnostic chemical assignments. Here, we uncover the identity and 3D spatial distribution of molecular species from gasoline, diesel injector and filter deposits with the 3D OrbiSIMS technique. Alkylbenzyl sulfonates, derived from lubricant oil contamination in the engine fuel cycle, were common to samples, we evidence transformation of the native sulfonate to longer chain species by reaction with fuel fragments in the gasoline deposit. Inorganic salts, identified in both diesel deposits, were prevalent throughout the injector deposits depth. We identified common polycyclic aromatic hydrocarbons up to C66H20, these were prevalent in the gasoline deposits lower depths. This work will enable deposit mitigation by unravelling their chemical composition, spatial distribution, and origins.</p>

scholarly journals Unambiguous Identification of Key Molecular Species in Deposits Responsible for Increased Pollution from Internal Combustion Engines

2020 ◽  
Author(s):  
Max K. Edney ◽  
Joseph S. Lamb ◽  
Matteo Spanu ◽  
Emily F. Smith ◽  
Elisabeth Steer ◽  
...  
Keyword(s):  
Spatial Distribution ◽  
Molecular Species ◽  
Internal Combustion Engines ◽  
Fuel Cycle ◽  
Combustion Engine ◽  
Engine Performance ◽  
Internal Combustion ◽  
Energy System ◽  
Pollutant Emissions ◽  
Engine Fuel

<p>Clean and efficient internal combustion engine performance will play a significant role in the move to a decarbonized energy system. Currently, fuel deposit formation on engine components negatively impacts CO2 and pollutant emissions, where previous attempts at deposit characterization afforded non-diagnostic chemical assignments. Here, we uncover the identity and 3D spatial distribution of molecular species from gasoline, diesel injector and filter deposits with the 3D OrbiSIMS technique. Alkylbenzyl sulfonates, derived from lubricant oil contamination in the engine fuel cycle, were common to samples, we evidence transformation of the native sulfonate to longer chain species by reaction with fuel fragments in the gasoline deposit. Inorganic salts, identified in both diesel deposits, were prevalent throughout the injector deposits depth. We identified common polycyclic aromatic hydrocarbons up to C66H20, these were prevalent in the gasoline deposits lower depths. This work will enable deposit mitigation by unravelling their chemical composition, spatial distribution, and origins.</p>

scholarly journals Detailed Experimental Investigation of A Spark Ignition Engine in A Wide Range of Work

2021 ◽  
Vol 1 (1) ◽  
Author(s):  
Melih Yıldız ◽  
Bilge Albayrak Çeper
Keyword(s):  
Thermal Efficiency ◽  
Internal Combustion Engines ◽  
Heat Dissipation ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Engine Fuel ◽  
Spark Ignition Engines ◽  
Combustion Control ◽  
Wide Range

For years, the goal of vehicle manufacturers; combustion control of spark ignition engines, ease of passage between the various cycles For years, the goal of vehicle manufacturers; combustion control of spark ignition engines, ease of passage between the various cycles, low emission values of diesel engines, high fuel economy and output power, thereby achieving optimum values in internal combustion engines. In this context, to improve the engine performance and increase the volumetric and thermal efficiency of the engine in all operating conditions to minimize the power losses and to reduce the exhaust emissions in order to obtain the maximum power, most economical and without environmental pollution, continues to be updated. In this study, the optimum working map of the engine was obtained by considering the power, torque, specific fuel consumption, cylinder pressure, exhaust gas temperature, thermal efficiency, average effective pressure, heat dissipation rate and emissions of four stroke, two cylinder, spark ignition SI engine fuel.

scholarly journals Performance and Emissions Analysis of N-Butanol Blended with Gasoline in Spark Ignition Engine

2018 ◽  
Vol 8 (4) ◽  
Author(s):  
Abdulrahman A ◽  
Adisa A. B. ◽  
Dandakouta H.
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Specific Energy Consumption ◽  
Engine Performance ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Gaseous Emissions ◽  
Exhaust Temperature ◽  
Carbon Dioxide Co2

The power developed by an internal-combustion engine depends upon the fuel used for combustion. Fuels commonly used in internal combustion engines are derived from crude oil, which are depleting and are important sources of air pollution. In this study, n-butanol was used as an additive with gasoline as fuel in spark ignition engine. N-butanol exhibits good burning characteristics, contain oxygen, reduces some exhaust emissions and as well, has energy density and octane rating close to that of gasoline. The various blend rates (4, 8, 12, 16 and 20 percent by volume) were used in the engine performance analysis using a TD110-115 single cylinder, four-stroke air-cooled spark ignition engine test rig, under different loading conditions. An SV-5Q automobile exhausts gas analyzer was used to measure the concentration of gaseous emissions such as unburnt hydrocarbon (UHC), carbon monoxide (CO), and carbon dioxide (CO2 ) from the engine tail pipe. The results of engine performance showed reduction in the exhaust temperature was observed for the blends than to that of gasoline. It was observed that all the blends improved the brake thermal efficiency and exhibited high fuel consumption, lower specific energy consumption and lower emissions than gasoline. All the blends performed satisfactorily on spark-ignition engine without engine modification.

scholarly journals Laminar Burning Velocity of Biogas-Containing Mixtures. A Literature Review

Processes ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 996
Author(s):  
Venera Giurcan ◽  
Codina Movileanu ◽  
Adina Magdalena Musuc ◽  
Maria Mitu
Keyword(s):  
Gas Turbines ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Combustion Engine ◽  
Burning Velocity ◽  
Internal Combustion ◽  
Electricity Production ◽  
Engine Fuel ◽  
Laminar Burning Velocity ◽  
Waste Products

Currently, the use of fossil fuels is very high and existing nature reserves are rapidly depleted. Therefore, researchers are turning their attention to find renewable fuels that have a low impact on the environment, to replace these fossil fuels. Biogas is a low-cost alternative, sustainable, renewable fuel existing worldwide. It can be produced by decomposition of vegetation or waste products of human and animal biological activity. This process is performed by microorganisms (such as methanogens and sulfate-reducing bacteria) by anaerobic digestion. Biogas can serve as a basis for heat and electricity production used for domestic heating and cooking. It can be also used to feed internal combustion engines, gas turbines, fuel cells, or cogeneration systems. In this paper, a comprehensive literature study regarding the laminar burning velocity of biogas-containing mixtures is presented. This study aims to characterize the use of biogas as IC (internal combustion) engine fuel, and to develop efficient safety recommendations and to predict and reduce the risk of fires and accidental explosions caused by biogas.

Ethers and esters as alternative fuels for internal combustion engine: A review

2021 ◽  
pp. 146808742110464
Author(s):  
Yang Hua
Keyword(s):  
Alternative Fuels ◽  
Combustion Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Engine Performance ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Future Research ◽  
Particulate Emissions ◽  
Ic Engine

Ether and ester fuels can work in the existing internal combustion (IC) engine with some important advantages. This work comprehensively reviews and summarizes the literatures on ether fuels represented by DME, DEE, DBE, DGM, and DMM, and ester fuels represented by DMC and biodiesel from three aspects of properties, production and engine application, so as to prove their feasibility and prospects as alternative fuels for compression ignition (CI) and spark ignition (SI) engines. These studies cover the effects of ether and ester fuels applied in the form of single fuel, mixed fuel, dual-fuel, and multi-fuel on engine performance, combustion and emission characteristics. The evaluation indexes mainly include torque, power, BTE, BSFC, ignition delay, heat release rate, pressure rise rate, combustion duration, exhaust gas temperature, CO, HC, NOx, PM, and smoke. The results show that ethers and esters have varying degrees of impact on engine performance, combustion and emissions. They can basically improve the thermal efficiency of the engine and reduce particulate emissions, but their effects on power, fuel consumption, combustion process, and CO, HC, and NOx emissions are uncertain, which is due to the coupling of operating conditions, fuel molecular structure, in-cylinder environment and application methods. By changing the injection strategy, adjusting the EGR rate, adopting a new combustion mode, adding improvers or synergizing multiple fuels, adverse effects can be avoided and the benefits of oxygenated fuel can be maximized. Finally, some challenges faced by alternative fuels and future research directions are analyzed.

Computationally Efficient Simulation of Multi-Component Fuel Combustion Using a Sparse Analytical Jacobian Chemistry Solver and High-Dimensional Clustering

2013 ◽  
Author(s):  
Federico Perini ◽  
Anand Krishnasamy ◽  
Youngchul Ra ◽  
Rolf D. Reitz
Keyword(s):  
Reaction Mechanism ◽  
Chemical Kinetics ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Engine Performance ◽  
Internal Combustion ◽  
Point Of View ◽  
High Dimensional ◽  
Computational Point ◽  
Fuel Surrogates

The need for more efficient and environmentally sustainable internal combustion engines is driving research towards the need to consider more realistic models for both fuel physics and chemistry. As far as compression ignition engines are concerned, phenomenological or lumped fuel models are unreliable to capture spray and combustion strategies outside of their validation domains — typically, high-pressure injection and high-temperature combustion. Furthermore, the development of variable-reactivity combustion strategies also creates the need to model comprehensively different hydrocarbon families even in single fuel surrogates. From the computational point of view, challenges to achieving practical simulation times arise from the dimensions of the reaction mechanism, that can be of hundreds species even if hydrocarbon families are lumped into representative compounds, and thus modeled with non-elementary, skeletal reaction pathways. In this case, it is also impossible to pursue further mechanism reductions to lower dimensions. CPU times for integrating chemical kinetics in internal combustion engine simulations ultimately scale with the number of cells in the grid, and with the cube number of species in the reaction mechanism. In the present work, two approaches to reduce the demands of engine simulations with detailed chemistry are presented. The first one addresses the demands due to the solution of the chemistry ODE system, and features the adoption of SpeedCHEM, a newly developed chemistry package that solves chemical kinetics using sparse analytical Jacobians. The second one aims to reduce the number of chemistry calculations by binning the CFD cells of the engine grid into a subset of clusters, where chemistry is solved and then mapped back to the original domain. In particular, a high-dimensional representation of the chemical state space is adopted for keeping track of the different fuel components, and a newly developed bounding-box-constrained k-means algorithm is used to subdivide the cells into reactively homogeneous clusters. The approaches have been tested on a number of simulations featuring multi-component diesel fuel surrogates, and different engine grids. The results show that significant CPU time reductions, of about one order of magnitude, can be achieved without loss of accuracy in both engine performance and emissions predictions, prompting for their applicability to more refined or full-sized engine grids.

Effect of IC Engine Operating Conditions on Combustion and Emission Characteristics

1993 ◽  
Vol 115 (4) ◽  
pp. 694-701 ◽  
Author(s):  
Jiang Lu ◽  
Ashwani K. Gupta ◽  
Eugene L. Keating
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Chamber ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Emission Characteristics ◽  
Ic Engine ◽  
Pollutants Emission ◽  
Good Agreement

Numerical simulation of flow, combustion, heat release rate, and pollutants emission characteristics have been obtained using a single cylinder internal combustion engine operating with propane as the fuel. The data show that for good agreement with experimental results on the peak pressure and the rate of pressure rise as a function of crank angle, spark ignition energy and local cylinder pressure must be properly modeled. The results obtained for NO and CO showed features which are qualitatively in good agreement and are similar to those reported in the literature for the chosen combustion chamber geometry. The results have shown that both the combustion chamber geometry and engine operating parameters affects the flame growth within the combustion chamber which subsequently affects the pollutants emission levels. The code employed the time marching procedure and solves the governing partial differential equations of multicomponent chemically reacting fluid flow by finite difference method. The numerical results provide a cost effective means of developing advanced internal combustion engine chamber geometry design that provides high efficiency and low pollution levels. It is expected that increased computational tools will be used in the future for enhancing our understanding of the detailed combustion process in internal combustion engines and all other energy conversion systems. Such detailed information is critical for the development of advanced methods for energy conservation and environmental pollution control.

Contactless Shaft Torque Detection for Wide Range Performance Measurement of Exhaust Gas Turbocharger Turbines

2013 ◽  
Vol 136 (6) ◽  
Author(s):  
Bernhardt Lüddecke ◽  
Dietmar Filsinger ◽  
Jan Ehrhard ◽  
Bastian Steinacher ◽  
Christian Seene ◽  
...  
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Sensitivity Study ◽  
Operating Conditions ◽  
Measuring System ◽  
Sensor Calibration ◽  
Torque Measurement ◽  
Wide Range ◽  
Shaft Torque

Turbochargers develop away from an auxiliary component—being “off the shelve”—towards an integrated component of the internal combustion engine. Hence, increased attention is paid to the accuracy of the measured turbine and compressor maps. Especially turbine efficiency measurement under engine-relevant operating conditions (pulsed flow) is recently receiving increased attention in the respective research community. Despite various turbine map extrapolation methods, sufficient accuracy of the input test data is indispensable. Accurate experimental data are necessary to achieve high quality extrapolation results, enabling a wide range and precise prediction of turbine behavior under unsteady flow conditions, determined by intermittent operation of the internal combustion engine. The present work describes the first application of a contactless shaft torque measurement technique—based on magnetostriction—to a small automotive turbocharger. The contactless torque measuring system is presented in detail and sensor principle as well as sensor calibration are illustrated. A sensitivity study regarding sensor position influences onto sensor signal proves the robustness and very good repeatability of the system. In the second part of the paper, steady state experimental results from operation on a conventional hot gas test stand over a wide map range are presented. These results are validated against full turbine stage (adiabatic as well as diabatic) CFD results as well as against “cold” efficiency measurements, based on measured inlet and outlet temperatures. The influence and relevance of bearing friction for such measurements is underlined and the improvements on this matter—achieved by direct torque measurement—are demonstrated.

Behavior Prediction Model in Gas Fueled Spark Ignition Internal Combustion Engines Turbocharged for Genset Application

2013 ◽  
Author(s):  
Jorge Duarte Forero ◽  
German Amador Diaz ◽  
Fabio Blanco Castillo ◽  
Lesme Corredor Martinez ◽  
Ricardo Vasquez Padilla
Keyword(s):  
Equivalence Ratio ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Combustion Engines ◽  
Gaseous Fuels ◽  
Methane Number

In this paper, a mathematical model is performed in order to analyze the effect of the methane number (MN) on knock tendency when spark ignition internal combustion engine operate with gaseous fuels produced from different thermochemical processes. The model was validated with experimental data reported in literature and the results were satisfactory. A general correlation for estimating the autoignition time of gaseous fuels in function of cylinder temperature, and pressure, equivalence ratio and methane number of the fuel was carried out. Livengood and Wu correlation is used to predict autoignition in function of the crank angle. This criterium is a way to predict the autoignition tendency of a fuel/air mixture under engine conditions and consider the ignition delay. A chemical equilibrium model which considers 98 chemical species was used in this research in order to simulate the combustion of the gaseous fuels at differents engine operating conditions. The effect of spark advance, equivalence ratio, methane number (MN), charge (inlet pressure) and inlet temperature (manifold temperature) on engine knocking is evaluated. This work, explore the feasibility of using syngas with low methane number as fuel for commercial internal combustion engines.

Sign in / Sign up

Export Citation Format

Share Document