Digital Microfluidic Device for Hotspot Cooling in ICS Using Electrowetting on Dielectric

2012 ◽  
Author(s):  
Govindraj Shreyas Bindiganavale ◽  
Hyejin Moon ◽  
Seung Mun You ◽  
Miguel Amaya
Keyword(s):  
Indium Tin Oxide ◽  
Single Phase ◽  
Cooling System ◽  
Liquid Droplet ◽  
Digital Microfluidics ◽  
Small Scale ◽  
Cooling Performance ◽  
Electrowetting On Dielectric ◽  
Drop Motion ◽  
Before And After

To meet the increasing demand of efficient cooling performance in small scale, this paper presents a digital microfluidics (DMF) microscale liquid cooling system which works on the principle of electrowetting on dielectric (EWOD). In EWOD DMF, fluids are handled drop-wise by external electric field. When the dispensed liquid droplet arrives at the hotspot by EWOD DMF operation, it picks up heat and removes heat when it leaves. This process can be repeated for a series of droplets by using a completely automated LabVIEW controlled system connected to the PCB package. With the help of indium tin oxide (ITO) thin film resistance temperature detectors (RTD) and pre-calibrated temperature coefficient of resistance (TCR) data, the temperatures of the hotspot before and after the residence of liquid droplet (i.e., cooling) can be recorded for different frequencies (dwelling time period of droplet on the hotspot) of the drop motion and varying heater power. Future work will involve RTD resistance data collection to plot the heat flux and the temperature difference (before and after cooling) for different frequencies of drop motion. Although the primary focus is to study single phase cooling, the DI water drop will experience considerable evaporation resulting in higher cooling performance. The single phase cooling studies will help in establishing a robust platform for future two-phase cooling analysis in which evaporation effects will be considered.

scholarly journals Designing Splicing Digital Microfluidics Chips Based on Polytetrafluoroethylene Membrane

Micromachines ◽  
2020 ◽  
Vol 11 (12) ◽  
pp. 1067
Author(s):  
Haoqiang Feng ◽  
Zichuan Yi ◽  
Ruizhi Yang ◽  
Xiaofeng Qin ◽  
Shitao Shen ◽  
...  
Keyword(s):  
Indium Tin Oxide ◽  
Silicone Oil ◽  
Digital Microfluidics ◽  
Simultaneous Detection ◽  
Driving Voltage ◽  
Electrowetting On Dielectric ◽  
Practical Applications ◽  
Multiple Components ◽  
Ito Glass ◽  
Off Time

As a laboratory-on-a-chip application tool, digital microfluidics (DMF) technology is widely used in DNA-based applications, clinical diagnosis, chemical synthesis, and other fields. Additional components (such as heaters, centrifuges, mixers, etc.) are required in practical applications on DMF devices. In this paper, a DMF chip interconnection method based on electrowetting-on-dielectric (EWOD) was proposed. An open modified slippery liquid-infused porous surface (SLIPS) membrane was used as the dielectric-hydrophobic layer material, which consisted of polytetrafluoroethylene (PTFE) membrane and silicone oil. Indium tin oxide (ITO) glass was used to manufacture the DMF chip. In order to test the relationship between the splicing gap and droplet moving, the effect of the different electrodes on/off time on the minimum driving voltage when the droplet crossed a splicing gap was investigated. Then, the effects of splicing gaps of different widths, splicing heights, and electrode misalignments were investigated, respectively. The experimental results showed that a driving voltage of 119 V was required for a droplet to cross a splicing gap width of 300 μm when the droplet volume was 10 μL and the electrode on/off time was 600 ms. At the same time, the droplet could climb a height difference of 150 μm with 145 V, and 141 V was required when the electrode misalignment was 1000 μm. Finally, the minimum voltage was not obviously changed, when the same volume droplet with different aqueous solutions crossed the splicing gap, and the droplet could cross different chip types. These splicing solutions show high potential for simultaneous detection of multiple components in human body fluids.

Study of Supersonic Micro-Channel for Cooling Electronic Devices

2013 ◽  
Author(s):  
Yuya Takahashi ◽  
Junnosuke Okajima ◽  
Yuka Iga ◽  
Atsuki Komiya ◽  
Wu-Shung Fu ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Gas Flow ◽  
Single Phase ◽  
Laval Nozzle ◽  
Cooling System ◽  
Supersonic Nozzle ◽  
Cooling Performance ◽  
Micro Scale ◽  
Mean Temperature

In this study, we focus on a micro-scale cooling device using a supersonic single phase gas flow. The single phase gas cooling system has advantages for cooling electronics device in a micro-scale. Generally, the forced convective heat transfer by single phase gas flow has a lower heat transfer coefficient than other heat transfer mechanisms. However, the heat transfer rate can be largely improved with a low temperature flow that is generated by isentropic expansion in supersonic nozzle. The objective of this study is to conduct a numerical evaluation of the possibility of this cooling system with a supersonic air flow through a heated micro-fin array. In order to calculate the supersonic flow inside the nozzle and evaluate the effect of the nozzle shape on the heat transfer, two types of nozzles are designed. One nozzle is a typical supersonic nozzle called Laval nozzle. The other is named Bump nozzle which has a simple arc shape at the throat. The channel size of both nozzles are about 200 μm in width and 2743.1 μm in length. In order to estimate the cooling performance, the numerical simulations were conducted by using ANSYS FLUENT 12.1 with the density-based Roe-FDS method. The inlet pressure, outlet pressure, and total pressure were set to 290 kPa, 100 kPa, and 367.1 kPa, respectively. The stagnation temperature and wall temperature were assumed 300 K and 350 K, respectively. The values of bulk mean temperature and Nusselt number were estimated. In both nozzles, the calculated bulk mean temperature was about 230 K and the Nusselt number was 7.54, which is the theoretical value of laminar forced convection between the parallel plates. The results showed that the Bump nozzle had almost the same cooling performance as the Laval nozzle in spite of its simple geometry in the each single channel. In addition, the Bump nozzle can have 4 times the number of channels the Laval nozzle configuration can occupy the same area because of its shape. This indicates that cooling performance of a device that includes the Bump nozzle geometry is higher than that of the Laval nozzle.

Study of Diabetic Mellitus and Knowledge of Lotion Foot Care on the Community

2018 ◽  
Vol 9 (3) ◽  
Author(s):  
Hariyadi DM ◽  
Athiyah U ◽  
Hendradi E ◽  
Rosita N ◽  
Erawati T ◽  
...  
Keyword(s):  
Blood Glucose ◽  
T Test ◽  
Small Scale ◽  
Scale Production ◽  
Foot Care ◽  
Diabetic Mellitus ◽  
Glucose Levels ◽  
Blood Glucose Levels ◽  
Before And After ◽  
History Of

The prevention of Diabetic Mellitus (DM) and its complications is the main aim of this study, in addition to the training of lotion foot care application and the development of small scale industry. The research team delivered knowledge in the form of training on Diabetic Mellitus, healthy food, treatment and prevention of complications, and small-scale production of cosmetic products. The aim of this study was to determine the correlation between training on diabetic and lotion foot care application as preventive measures against diabetic complications on the patient's blood glucose levels in the community of residents in Banyuurip Jaya, Surabaya. It was expected from this training that the knowledge of the residents increases and people living with diabetic undergo lifestyle changes and therefore blood sugar levels can be controlled. The parameters measured in this research were blood glucose levels, the anti diabetic drug types consumed, and compliance on diabetics. This study used the data taken from 60 patients with DM over a period of one month. Questionnaires and log books was used to retrieve data and changes in blood glucose levels in diabetic patients. The results showed the demographic data of patients with type 2 diabetic of 85% female and 15% male, with the range of patients aged of 61-70 years of 46.67% and had history of diabetic (90%). The history of drugs consumed by respondents was anti diabetic drugs such as metformin (40%), glimepiride (33.37%) and insulin (6.67%). In addition, the increased knowledge of DM patients after being given the training compared to before training was shown in several questions in the questionnaire. A statistical analysis using t-test analyzed a correlation between training provided in order to enhance understanding of the patient, as well as correlation with blood glucose levels. A paired T-test showed that there was a relationship between the knowledge of trainees before and after training (p less than 0.05). An interesting result was that there was no relationship between blood glucose levels before and after training provided (p> 0.05).

scholarly journals Development and Evaluation of an Ultrasonic Humidifier to Control Humidity in a Cold Storage Room for Postharvest Quality Management of Dates

Foods ◽  
2021 ◽  
Vol 10 (5) ◽  
pp. 949
Author(s):  
Maged Mohammed ◽  
Nashi Alqahtani ◽  
Hamadttu El-Shafie
Keyword(s):  
Quality Management ◽  
Cold Storage ◽  
Cooling System ◽  
Positive Impact ◽  
Droplet Diameter ◽  
Postharvest Quality ◽  
Main Element ◽  
Small Scale ◽  
Storage Room ◽  
Ultrasonic Humidifier

Dates are subjected to postharvest losses in quality and quantity caused by water loss, fermentation, insect infestation, and microbial spoilage during storage. Cold storage is the main element in the postharvest quality management used for fruit preservation. Although cold storage is used for dates, precision control of the relative humidity (RH) using ultrasonic applications is not used thus far, or it is applied to other fruits on a small scale. Therefore, we designed and constructed an ultrasonic humidifier (DUH) for RH control in the cold storage room (CSR) of dates. The optimum air velocity of 3 m s−1 at the outlets of the DUH ducts produced a mist amount of 6.8 kg h-1 with an average droplet diameter of 4.26 ± 1.43 µm at the applied voltage of 48 V and frequency of 2600 kHz of the transducers. The experimental validation was carried out by comparing a CSR controlled with the DUH with two conventional CSRs. The three tested CSRs were similar in dimensions, cooling system, and amount of stored dates. The time required for cooling 800 kg of dates in the controlled CSR from 25 °C to the target temperature of 5 °C was approximately 48 h. The DUH precisely controlled the RH at the maximum RH set point of 80% in the tested CSR at 5 °C. The controlled RH at 80% has a positive impact on the physicochemical characteristics of the stored dates. It significantly reduced the weight loss of the fruits and preserved fruit mass, moisture content, water activity, firmness, and color parameters. However, no significant effect was observed on fruit dimensions, sphericity, and aspect ratio. The microbial loads of mesophilic aerobic bacteria, molds, and yeasts fell within the acceptable limits in all tested CSRs. Both stored date fruits and artificially infested dates showed no signs of insect activity in the controlled CSR at the temperature of 5 °C and RH of 80%. The DUH proved to be a promising technology for postharvest quality management for dates during cold storage.

scholarly journals Species and characteristics of volatile organic compounds emitted from an auto-repair painting workshop

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
M. Y. Song ◽  
H. Chun
Keyword(s):  
Volatile Organic Compounds ◽  
Organic Compounds ◽  
Large Scale ◽  
Butyl Acetate ◽  
Small Scale ◽  
Indoor Environments ◽  
Voc Emissions ◽  
Volatile Organic ◽  
Before And After ◽  
Adsorption Systems

AbstractVolatile organic compounds (VOCs) are secondary pollutant precursors having adverse impacts on the environment and human health. Although VOC emissions, their sources, and impacts have been investigated, the focus has been on large-scale industrial sources or indoor environments; studies on relatively small-scale enterprises (e.g., auto-repair workshops) are lacking. Here, we performed field VOC measurements for an auto-repair painting facility in Korea and analyzed the characteristics of VOCs emitted from the main painting workshop (top coat). The total VOC concentration was 5069–8058 ppb, and 24–35 species were detected. The VOCs were mainly identified as butyl acetate, toluene, ethylbenzene, and xylene compounds. VOC characteristics differed depending on the paint type. Butyl acetate had the highest concentration in both water- and oil-based paints; however, its concentration and proportion were higher in the former (3256 ppb, 65.5%) than in the latter (2449 ppb, 31.1%). Comparing VOC concentration before and after passing through adsorption systems, concentrations of most VOCs were lower at the outlets than the inlets of the adsorption systems, but were found to be high at the outlets in some workshops. These results provide a theoretical basis for developing effective VOC control systems and managing VOC emissions from auto-repair painting workshops.

Effect of Full- and Small-Scale Reeling Simulation on Mechanical Properties of Weldable 13Cr Seamless Line Pipe

2013 ◽  
Author(s):  
Hidenori Shitamoto ◽  
Nobuyuki Hisamune
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Oil And Gas ◽  
Small Scale ◽  
Line Pipe ◽  
Offshore Pipeline ◽  
Oil And Gas Pipelines ◽  
Before And After ◽  
Offshore Oil And Gas ◽  
Offshore Oil

There are several methods currently being used to install offshore oil and gas pipelines. The reel-lay process is fast and one of the most effective offshore pipeline installation methods for seamless, ERW, and UOE line pipes with outside diameters of 18 inches or less. In the case of the reel-laying method, line pipes are subjected to plastic deformation multiplication during reel-laying. It is thus important to understand the change of the mechanical properties of line pipes before and after reel-laying. Therefore, full-scale reeling (FSR) simulations and small-scale reeling (SSR) simulations are applied as evaluation tests for reel-laying. In this study, FSR simulations were performed to investigate the effect of cyclic deformation on the mechanical properties of weldable 13Cr seamless line pipes. Furthermore, SSR simulations were performed to compare the results obtained by FSR simulations.

Experimental and Numerical Evaluation of Small-Scale Cryosurgery Using Ultrafine Cryoprobe

2013 ◽  
Vol 4 (4) ◽  
Author(s):  
Junnosuke Okajima ◽  
Atsuki Komiya ◽  
Shigenao Maruyama
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Heat Transfer Coefficient ◽  
Temperature Distribution ◽  
Surface Temperature ◽  
Numerical Evaluation ◽  
Small Scale ◽  
Outer Diameter ◽  
Cooling Performance ◽  
The Heat Transfer Coefficient

The objective of this work is to experimentally and numerically evaluate small-scale cryosurgery using an ultrafine cryoprobe. The outer diameter (OD) of the cryoprobe was 550 μm. The cooling performance of the cryoprobe was tested with a freezing experiment using hydrogel at 37 °C. As a result of 1 min of cooling, the surface temperature of the cryoprobe reached −35 °C and the radius of the frozen region was 2 mm. To evaluate the temperature distribution, a numerical simulation was conducted. The temperature distribution in the frozen region and the heat transfer coefficient was discussed.

scholarly journals Influence of Thermal Annealing on the Electrical Properties of Poly(3-hexylthiophene)-Based Thin Film Diodes

2007 ◽  
Vol 62 (10-11) ◽  
pp. 609-619 ◽  
Author(s):  
Zivayi Chiguvare ◽  
Jürgen Parisi ◽  
Vladimir Dyakonov
Keyword(s):  
Thin Film ◽  
Thermal Annealing ◽  
Indium Tin Oxide ◽  
Bulk Heterojunction ◽  
Polymer Chains ◽  
Hole Injection ◽  
Before And After ◽  
Output Characteristics ◽  
Al Thin Film ◽  
Poly Styrene Sulfonate

The effects of thermal annealing on the bulk transport properties of poly(3-hexylthiophene) (P3HT) were studied by analyzing room temperature current-voltage characteristics of polymer thin films sandwiched between indium tin oxide/poly[ethylene dioxythiophene]:poly[styrene sulfonate] (ITO/PEDOT:PSS) and aluminum electrodes, before and after a thermal annealing step. It was observed that annealing takes place in two steps: (1) Dedoping of the polymer of impurities such as oxygen, remnant solvent, water, leading to a decrease in the conductivity of the film, and (2) thermally induced motion of the polymer chains leading to closer packing, thus, stronger inter-chain interaction and, consequently, increase in conductivity. It was also observed that the ITO/PEDOT:PSS/P3HT hole injection barrier increases on annealing the ITO/PEDOT:PSS/P3HT/Al thin film devices. The implications of impurity dedoping and closer packing on the output characteristics of bulk heterojunction polymer-fullerene thin film solar cells are discussed.

Sign in / Sign up

Export Citation Format

Share Document