Location of interconnect defects using focused ion beam (FIB) induced voltage contrast and subsequent auger electron analysis of in-situ FIB cross sections in the physical electronics 200/300-mm SMART-tool

2003 ◽  
Author(s):  
Carolyn F. H. Gondran ◽  
Dennis F. Paul ◽  
Kenton D. Childs ◽  
Laurie G. Dennig ◽  
Greg C. Smith
Keyword(s):  
Cross Sections ◽  
Auger Electron ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Induced Voltage ◽  
Voltage Contrast

Investigations of Leakage Paths in Sub-0.35μm DRAM Products Using Advanced Focused Ion Beam Techniques

1998 ◽  
Author(s):  
H. Lorenz ◽  
C. Engel
Keyword(s):  
Focused Ion Beam ◽  
Cell Function ◽  
Dielectric Breakdown ◽  
Ion Beam ◽  
Electrical Characterization ◽  
Floating Gate ◽  
Leakage Path ◽  
Contrast Technique ◽  
Voltage Contrast

Abstract Due to the continuously decreasing cell size of DRAMs and concomitantly diminishing thickness of some insulating layers new failure mechanisms appear which until now had no significance for the cell function. For example high resistance leakage paths between closely spaced conductors can lead to retention problems. These are hard to detect by electrical characterization in a memory tester because the involved currents are in the range of pA. To analyze these failures we exploit the very sensitive passive voltage contrast of the Focused Ion Beam Microscope (FIB). The voltage contrast can further be enhanced by in-situ FIB preparations to obtain detailed information about the failure mechanism. The first part of this paper describes a method to detect a leakage path between a borderless contact on n-diffusion and an adjacent floating gate by passive voltage contrast achieved after FIB circuit modification. In the second part we will demonstrate the localization of a DRAM trench dielectric breakdown. In this case the FIB passive voltage contrast technique is not limited to the localization of the failing trench. We can also obtain the depth of the leakage path by selective insitu etching with XeF2 stopped immediately after a voltage contrast change.

Focused Ion Beam Grounding to Alleviate Sample Charging for Scanning Auger Electron Spectroscopy

2006 ◽  
Author(s):  
Carolyn F. H. Gondran ◽  
Emily Morales
Keyword(s):  
Electron Beam ◽  
Auger Electron Spectroscopy ◽  
Electron Spectroscopy ◽  
Auger Electron ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Contrast Analysis ◽  
Voltage Contrast

Abstract It is shown that a focused ion beam (FIB) grounding technique can be used to alleviate charge buildup on samples that would otherwise charge in the electron beam to the point where analysis by Auger electron spectroscopy (AES) was limited or impossible. FIB grounding alleviates the sample charging and permits AES analysis. The grounding technique is quick, easy and well understood as it has been used extensively for voltage-contrast analysis. The technique is shown to be useful for enabling analysis on electrically isolated conductive features as well as insulating samples.

FIB-Etching of Polymer/Metal Laminates and its Effect on Mechanical Performance

2014 ◽  
Vol 20 (6) ◽  
pp. 1826-1834
Author(s):  
Enne Faber ◽  
Willem P. Vellinga ◽  
Jeff T.M. De Hosson
Keyword(s):  
Mechanical Properties ◽  
Polyethylene Terephthalate ◽  
Cross Sections ◽  
Focused Ion Beam ◽  
Mechanical Performance ◽  
Ion Beam ◽  
Ion Beam Etching ◽  
Polymer Metal ◽  
The Impact

AbstractThis paper investigates the adhesive interface in a polymer/metal (polyethylene terephthalate/steel) laminate that is subjected to uniaxial strain. Cross-sections perpendicular to such interfaces were created with a focused ion beam and imaged with scanning electron microscopy during straining in the electron microscope. During in situ straining, glide steps formed by the steel caused traction at the interface and initiated crazes in the polyethylene terephthalate (PET). These crazes readily propagated along the free surface of the PET layer. Similar crazing has not been previously encountered in laminates that were pre-strained or in numerical calculations. The impact of focused ion beam treatments on mechanical properties of the polymer/metal laminate system was therefore investigated. It was found that mechanical properties such as toughness of PET are dramatically influenced by focused ion beam etching. It was also found that this change in mechanical properties has a different effect on the pre-strained and in situ strained samples.

In-Situ Electrical Monitoring and Contactless Measurement Techniques for Enhanced FIB Modifications

1998 ◽  
Author(s):  
Romain Desplats ◽  
Jamel Benbrik ◽  
Philippe Perdu ◽  
Bruno Benteo ◽  
François Marc ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Measurement Techniques ◽  
Contactless Measurement ◽  
Design Modification ◽  
Area Of Interest ◽  
Milling Operations ◽  
Voltage Contrast ◽  
Metal Layers

Abstract Recent planar technologies with 3 metal layers or more challenge current physical design modification capacities using Focused Ion Beam tools. Image visibility on the FIB is drastically reduced, making accurate positioning and milling operations in the area of interest more difficult, and the use of power planes increases the risk of short circuits while accessing inferior metal lines. Despite the complexity of FIB modifications, however, the demand for circuit modifications continues to increase. To respond to this demand for successful, time efficient, FIB modifications, step by step monitoring of operations is imperative. In this paper, we will present an innovative method which brings in-situ electrical monitoring and contactless measurement capabilities to FIB systems. Electrical connection of the circuit inside the vacuum FIB chamber is done using a commercial load module and logic waveform acquisition with the FIB is obtained without modifying FIB hardware using a voltage contrast approach. With this method, it is possible to verify the completion of FIB milling and depositing operations by temporarily suspending FIB action so that a test pattern can be run allowing electrical testing and measurements of the circuit without damaging it.

An Study of Influence of Imperfections on the Delamination of Diamond-Like Carbon Films

2002 ◽  
Vol 719 ◽  
Author(s):  
Myoung-Woon Moon ◽  
Kyang-Ryel Lee ◽  
Jin-Won Chung ◽  
Kyu Hwan Oh
Keyword(s):  
Cross Sections ◽  
Focused Ion Beam ◽  
Imaging System ◽  
Ion Beam ◽  
Carbon Films ◽  
Diamond Like Carbon ◽  
Glass Substrates ◽  
Atomic Force ◽  
Initiation And Propagation

AbstractThe role of imperfections on the initiation and propagation of interface delaminations in compressed thin films has been analyzed using experiments with diamond-like carbon (DLC) films deposited onto glass substrates. The surface topologies and interface separations have been characterized by using the Atomic Force Microscope (AFM) and the Focused Ion Beam (FIB) imaging system. The lengths and amplitudes of numerous imperfections have been measured by AFM and the interface separations characterized on cross sections made with the FIB. Chemical analysis of several sites, performed using Auger Electron Spectroscopy (AES), has revealed the origin of the imperfections. The incidence of buckles has been correlated with the imperfection length.

Analysis of Voltage Contrast in Secondary Electron Images Using a High-Energy Electron Spectrometer

2019 ◽  
Author(s):  
Natsuko Asano ◽  
Shunsuke Asahina ◽  
Natasha Erdman
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Sample Surface ◽  
High Energy ◽  
Secondary Electrons ◽  
Analysis Technique ◽  
Quantitative Understanding ◽  
Voltage Contrast ◽  
Acceleration Voltage ◽  
Failure Localization

Abstract Voltage contrast (VC) observation using a scanning electron microscope (SEM) or a focused ion beam (FIB) is a common failure analysis technique for semiconductor devices.[1] The VC information allows understanding of failure localization issues. In general, VC images are acquired using secondary electrons (SEs) from a sample surface at an acceleration voltage of 0.8–2.0 kV in SEM. In this study, we aimed to find an optimized electron energy range for VC acquisition using Auger electron spectroscopy (AES) for quantitative understanding.

FIB Enhancement of Mechanically Polished Cross-sections

2019 ◽  
Author(s):  
Becky Holdford
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
Scanning Electron Microscope ◽  
Cross Sections ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
High Resolution Imaging ◽  
Chemical Attack ◽  
Resolution Imaging ◽  
Scanning Electron

Abstract On mechanically polished cross-sections, getting a surface adequate for high-resolution imaging is sometimes beyond the analyst’s ability, due to material smearing, chipping, polishing media chemical attack, etc.. A method has been developed to enable the focused ion beam (FIB) to re-face the section block and achieve a surface that can be imaged at high resolution in the scanning electron microscope (SEM).

Application of FIB Circuit Edit in Analysis of Memory Failure of SOI Devices

2006 ◽  
Author(s):  
Z. G. Song ◽  
S. K. Loh ◽  
X. H. Zheng ◽  
S.P. Neo ◽  
C. K. Oh
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Electrical Characterization ◽  
Silicon On Insulator ◽  
First Case ◽  
Edx Analyses ◽  
Memory Failure ◽  
Soi Devices ◽  
Voltage Contrast ◽  
Soi Technology

Abstract This article presents two cases to demonstrate the application of focused ion beam (FIB) circuit edit in analysis of memory failure of silicon on insulator (SOI) devices using XTEM and EDX analyses. The first case was a single bit failure of SRAM units manufactured with 90 nm technology in SOI wafer. The second case was the whole column failure with a single bit pass for a SRAM unit. From the results, it was concluded that FIB circuit edit and electrical characterization is a good methodology for further narrowing down the defective location of memory failure, especially for SOI technology, where contact-level passive voltage contrast is not suitable.

To Eliminate Curtain Effect of FIB TEM Samples by a Combination of Sample Dicing and Backside Milling

2014 ◽  
Author(s):  
Jian-Shing Luo ◽  
Hsiu Ting Lee
Keyword(s):  
Sample Preparation ◽  
Focused Ion Beam ◽  
Preparation Method ◽  
Low Cost ◽  
Ion Beam ◽  
Sample Preparation Method ◽  
Site Specific ◽  
Dual Beam ◽  
Transmission Electron

Abstract Several methods are used to invert samples 180 deg in a dual beam focused ion beam (FIB) system for backside milling by a specific in-situ lift out system or stages. However, most of those methods occupied too much time on FIB systems or requires a specific in-situ lift out system. This paper provides a novel transmission electron microscopy (TEM) sample preparation method to eliminate the curtain effect completely by a combination of backside milling and sample dicing with low cost and less FIB time. The procedures of the TEM pre-thinned sample preparation method using a combination of sample dicing and backside milling are described step by step. From the analysis results, the method has applied successfully to eliminate the curtain effect of dual beam FIB TEM samples for both random and site specific addresses.

Sign in / Sign up

Export Citation Format

Share Document