Performance enhancement of MEMS-guided four beam piezoelectric transducers for energy harvesting and acceleration sensing

2019 ◽  
Vol 33 (18) ◽  
pp. 1950192 ◽  
Author(s):  
Hossein Ghoddus ◽  
Zoheir Kordrostami ◽  
Peyman Amiri
Keyword(s):  
Output Voltage ◽  
Performance Enhancement ◽  
Piezoelectric Transducers ◽  
Maximum Output ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Resonance Frequencies ◽  
First Time ◽  
Piezoelectric Acceleration ◽  
Good Agreement

In the present paper, guided four beam (G4B) piezoelectric transducers with enhanced sensitivities have been designed. Based on the suggested G4B structures, piezoelectric energy harvesters (PEHs) and acceleration transducers with higher voltages than their previously reported counterparts and with lower displacements than the single-cantilever PEHs (SC-PEHs) have been proposed. We have shown that it is possible to arrive at much more output voltages in comparison with the conventional PEHs by redesigning the structure of the cantilever beams. In 1 g acceleration, the maximum output voltage obtained from the proposed PEHs has been 13.49 V whereas the output voltage for the conventional G4B-PEH is 2.87 V. This paper for the first time proposes G4B-PEHs with smaller displacements and larger voltages compared to a SC-PEH. The same G4B framework has been studied as a piezoelectric acceleration transducer. The effect of piezoelectric length on the extracted voltage in both unimorph and bimorph cantilevers has been discussed and the optimized length has been calculated. An analytical method is developed to compute the resonance frequencies of different beam shapes whose results are in a good agreement with numerical simulations.

scholarly journals Design and Experimental Study of an L Shape Piezoelectric Energy Harvester

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
In-Ho Kim ◽  
Seon-Jun Jang ◽  
Hyung-Jo Jung
Keyword(s):  
Output Voltage ◽  
Energy Harvester ◽  
Performance Enhancement ◽  
Mechanical Strain ◽  
Electrical Energy ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Cantilevered Beam ◽  
Beam Type ◽  
Low Efficiency

Piezoelectric energy harvesters of cantilevered beam type are studied in various fields due to simplicity. In general, these systems obtain electrical energy from mechanical strain by bending of cantilevered beam. However, conventional systems have disadvantages that they have low efficiency in frequency regions other than resonance frequency. To overcome the limitations, various energy harvesters to apply performance enhancement strategies are proposed and investigated. In this paper, a frequency-changeable L shape energy harvester which is form connected cantilever beam and rigid arm is proposed and investigated. The conventional piezoelectric energy harvester exhibits the principal frequency in the simple bending mode whereas the proposed system features the twisting mode resulting in a higher output voltage than the conventional system. The proposed energy harvester is simplified to a two-degree-of-freedom model and its dynamics are described. How the length of a rigid bar affects its natural frequencies is also studied. To evaluate the performance of the system, experiments by using a vertical shaker and numerical simulation are carried out. As a result, it is shown that the natural frequency for a twisting mode decreases as the arm length increased, and the higher output voltage is generated comparing with those of the conventional energy harvester.

scholarly journals Analytical Modeling of a Doubly Clamped Flexible Piezoelectric Energy Harvester with Axial Excitation and Its Experimental Characterization

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3861
Author(s):  
Jie Mei ◽  
Qiong Fan ◽  
Lijie Li ◽  
Dingfang Chen ◽  
Lin Xu ◽  
...  
Keyword(s):  
Output Power ◽  
Power Output ◽  
Output Voltage ◽  
Energy Harvester ◽  
Load Resistance ◽  
Engineering Practice ◽  
Maximum Output ◽  
Widespread Application ◽  
Piezoelectric Energy ◽  
Axial Excitation

With the rapid development of wearable electronics, novel power solutions are required to adapt to flexible surfaces for widespread applications, thus flexible energy harvesters have been extensively studied for their flexibility and stretchability. However, poor power output and insufficient sensitivity to environmental changes limit its widespread application in engineering practice. A doubly clamped flexible piezoelectric energy harvester (FPEH) with axial excitation is therefore proposed for higher power output in a low-frequency vibration environment. Combining the Euler–Bernoulli beam theory and the D’Alembert principle, the differential dynamic equation of the doubly clamped energy harvester is derived, in which the excitation mode of axial load with pre-deformation is considered. A numerical solution of voltage amplitude and average power is obtained using the Rayleigh–Ritz method. Output power of 22.5 μW at 27.1 Hz, with the optimal load resistance being 1 MΩ, is determined by the frequency sweeping analysis. In order to power electronic devices, the converted alternating electric energy should be rectified into direct current energy. By connecting to the MDA2500 standard rectified electric bridge, a rectified DC output voltage across the 1 MΩ load resistor is characterized to be 2.39 V. For further validation of the mechanical-electrical dynamical model of the doubly clamped flexible piezoelectric energy harvester, its output performances, including both its frequency response and resistance load matching performances, are experimentally characterized. From the experimental results, the maximum output power is 1.38 μW, with a load resistance of 5.7 MΩ at 27 Hz, and the rectified DC output voltage reaches 1.84 V, which shows coincidence with simulation results and is proved to be sufficient for powering LED electronics.

Design of a piezoelectric energy conversion based wind generator

2021 ◽  
pp. 002072092110134
Author(s):  
Sibel Akkaya Oy ◽  
Ali Ekber Özdemir
Keyword(s):  
Low Power ◽  
Energy Conversion ◽  
Output Voltage ◽  
Sensor Nodes ◽  
Maximum Output ◽  
Wireless Sensor Nodes ◽  
Wind Speeds ◽  
Wind Generator ◽  
Piezoelectric Energy ◽  
Renewable Energy Generation

This manuscript presents a new experimental wind generator based on piezoelectric energy conversion for low power applications. The aim is to demonstrate an alternative renewable energy generation method for low power applications. The generator has four blades of a propeller equipped with a total of twenty-four (24) thin film piezoelectric transducers (TFPTs). The output voltage is generated using a newly developed circuit topology. The generator was tested at three wind speeds 10 m/s, 14 m/s and 18 m/s, with a maximum output voltage of 10.2 V being produced at a wind speed of 18 m/s. Results show that this generator has promise to be suitable for low power batteryless applications, for example wireless sensor nodes (WSN).

Broadband Rotational Energy Harvesting Using Micro Energy Harvester

2018 ◽  
Author(s):  
Jui-Ta Chien ◽  
Yung-Hsing Fu ◽  
Chao-Ting Chen ◽  
Shun-Chiu Lin ◽  
Yi-Chung Shu ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Low Frequency ◽  
Rotational Energy ◽  
Open Circuit ◽  
Maximum Output ◽  
Rotational Excitation ◽  
Rotating Speed ◽  
Piezoelectric Energy

This paper proposes a broadband rotational energy harvesting setup by using micro piezoelectric energy harvester (PEH). When driven in different rotating speed, the PEH can output relatively high power which exhibits the phenomenon of frequency up-conversion transforming the low frequency of rotation into the high frequency of resonant vibration. It aims to power self-powered devices used in the applications, like smart tires, smart bearings, and health monitoring sensors on rotational machines. Through the excitation of the rotary magnetic repulsion, the cantilever beam presents periodically damped oscillation. Under the rotational excitation, the maximum output voltage and power of PEH with optimal impedance is 28.2 Vpp and 663 μW, respectively. The output performance of the same energy harvester driven in ordinary vibrational based excitation is compared with rotational oscillation under open circuit condition. The maximum output voltage under 2.5g acceleration level of vibration is 27.54 Vpp while the peak output voltage of 36.5 Vpp in rotational excitation (in 265 rpm).

scholarly journals FINITE ELEMENT SIMULATION OF MEMS PIEZOELECTRIC ENERGY SCAVENGER BASED ON PZT THIN FILM

2019 ◽  
Vol 20 (1) ◽  
pp. 90-99
Author(s):  
Aliza Aini Md Ralib ◽  
Nur Wafa Asyiqin Zulfakher ◽  
Rosminazuin Ab Rahim ◽  
Nor Farahidah Za'bah ◽  
Noor Hazrin Hany Mohamad Hanif
Keyword(s):  
Thin Film ◽  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Piezoelectric Energy ◽  
The World

Vibration energy harvesting has been progressively developed in the advancement of technology and widely used by a lot of researchers around the world. There is a very high demand for energy scavenging around the world due to it being cheaper in price, possibly miniaturized within a system, long lasting, and environmentally friendly. The conventional battery is hazardous to the environment and has a shorter operating lifespan. Therefore, ambient vibration energy serves as an alternative that can replace the battery because it can be integrated and compatible to micro-electromechanical systems. This paper presents the design and analysis of a MEMS piezoelectric energy harvester, which is a vibration energy harvesting type. The energy harvester was formed using Lead Zicronate Titanate (PZT-5A) as the piezoelectric thin film, silicon as the substrate layer and structural steel as the electrode layer. The resonance frequency will provide the maximum output power, maximum output voltage and maximum displacement of vibration. The operating mode also plays an important role to generate larger output voltage with less displacement of cantilever. Some designs also have been studied by varying height and length of piezoelectric materials. Hence, this project will demonstrate the simulation of a MEMS piezoelectric device for a low power electronic performance. Simulation results show PZT-5A piezoelectric energy with a length of 31 mm and height of 0.16 mm generates maximum output voltage of 7.435 V and maximum output power of 2.30 mW at the resonance frequency of 40 Hz. ABSTRAK: Penuaian tenaga getaran telah berkembang secara pesat dalam kemajuan teknologi dan telah digunakan secara meluas oleh ramai penyelidik di seluruh dunia. Terdapat permintaan yang sangat tinggi di seluruh dunia terhadap penuaian tenaga kerana harganya yang lebih murah, bersaiz kecil dalam satu sistem, tahan lama dan mesra alam. Manakala, bateri konvensional adalah berbahaya bagi alam sekitar dan mempunyai jangka hayat yang lebih pendek. Oleh itu, getaran tenaga dari persekitaran lebih sesuai sebagai alternatif kepada bateri kerana ia mudah diintegrasikan dan serasi dengan sistem mikroelektromekanikal. Kertas kerja ini  membentangkan reka bentuk dan analisis tenaga piezoelektrik MEMS iaitu salah satu jenis penuaian tenaga getaran. Penuai tenaga ini dibentuk menggunakan Lead Zicronate Titanate (PZT-5A) sebagai lapisan filem tipis piezoelektrik, silikon sebagai lapisan substrat dan keluli struktur sebagai lapisan elektrod. Frekuensi resonans akan memberikan hasil tenaga maksima, voltan tenaga maksima dan getaran jarak maksima. Mod pengendalian juga memainkan peranan penting bagi menghasilkan tenaga yang lebih besar. Reka bentuk yang mempunyai ketinggian dan panjang berlainan juga telah diuji dengan menggunakan bahan piezoelektrik yang sama. Oleh itu, projek ini akan menghasilkan simulasi piezoelektrik MEMS yang sesuai digunakan bagi alat elektronik berkuasa rendah. Hasil simulasi menunjukkan dengan panjang 31 mm dan ketinggian 0.16 mm, piezoelektrik PZT ini menghasilkan voltan maksima sebanyak 7.435 V dan tenaga output maksima 2.30 mW pada frekuensi resonans 40 Hz.

scholarly journals Experimental Study on Piezoelectric Energy Harvesting from Vortex-Induced Vibrations and Wake-Induced Vibrations

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Min Zhang ◽  
Junlei Wang
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Maximum Output Power ◽  
Load Resistance ◽  
Maximum Output ◽  
Piezoelectric Energy ◽  
Vortex Induced Vibrations ◽  
Flow Induced Vibrations ◽  
Generation Capacity ◽  
Output Characteristics

A rigid circular cylinder with two piezoelectric beams attached on has been tested through vortex-induced vibrations (VIV) and wake-induced vibrations (WIV) by installing a big cylinder fixed upstream, in order to study the influence of the different flow-induced vibrations (FIV) types. The VIV test shows that the output voltage increases with the increases of load resistance; an optimal load resistance exists for the maximum output power. The WIV test shows that the vibration of the small cylinder is controlled by the vortex frequency of the large one. There is an optimal gap of the cylinders that can obtain the maximum output voltage and power. For a same energy harvesting device, WIV has higher power generation capacity; then the piezoelectric output characteristics can be effectively improved.

scholarly journals THE NUCLEAR SPIN RESONANCE SPECTRUM OF Al27 IN SPODUMENE

1958 ◽  
Vol 36 (10) ◽  
pp. 1295-1307 ◽  
Author(s):  
L. B. Robinson
Keyword(s):  
Nuclear Spin ◽  
Resonance Spectrum ◽  
Companion Paper ◽  
Quadrupole Interactions ◽  
Resonance Frequencies ◽  
Spin Resonance ◽  
Theoretical Predictions ◽  
Induction Type ◽  
First Time ◽  
Good Agreement

An experimental study has been made of the nuclear spin resonance spectrum of Al27 in a single crystal of spodumene (LiAl(SiO3)2) over a range of external magnetic field H0 wide enough [Formula: see text] to bridge for the first time the gap between pure quadrupole spectra (R = 0) and Zeeman spectra slightly perturbed by quadrupole interactions [Formula: see text]. Experimental results on the resonance frequencies and relative signal amplitudes obtained with an induction type of nuclear resonance spectrometer are described, and are found to be in good agreement with the theoretical predictions given in the preceding companion paper.

scholarly journals Performance Enhancement of a Multiresonant Piezoelectric Energy Harvester for Low Frequency Vibrations

Energies ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2770 ◽  
Author(s):  
Iman Izadgoshasb ◽  
Yee Lim ◽  
Ricardo Vasquez Padilla ◽  
Mohammadreza Sedighi ◽  
Jeremy Novak
Keyword(s):  
Cantilever Beam ◽  
Performance Enhancement ◽  
Low Frequency ◽  
Design Parameters ◽  
Vibration Source ◽  
Element Analysis ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Low Frequency Vibration ◽  
External Power Source

Harvesting electricity from low frequency vibration sources such as human motions using piezoelectric energy harvesters (PEH) is attracting the attention of many researchers in recent years. The energy harvested can potentially power portable electronic devices as well as some medical devices without the need of an external power source. For this purpose, the piezoelectric patch is often mechanically attached to a cantilever beam, such that the resonance frequency is predominantly governed by the cantilever beam. To increase the power generated from vibration sources with varying frequency, a multiresonant PEH (MRPEH) is often used. In this study, an attempt is made to enhance the performance of MRPEH with the use of a cantilever beam of optimised shape, i.e., a cantilever beam with two triangular branches. The performance is further enhanced through optimising the design of the proposed MRPEH to suit the frequency range of the targeted vibration source. A series of parametric studies were first carried out using finite-element analysis to provide in-depth understanding of the effect of each design parameters on the power output at a low frequency vibration. Selected outcomes were then experimentally verified. An optimised design was finally proposed. The results demonstrate that, with the use of a properly designed MRPEH, broadband energy harvesting is achievable and the efficiency of the PEH system can be significantly increased.

Equivalent impedance and power analysis of monostable piezoelectric energy harvesters

2020 ◽  
Vol 31 (14) ◽  
pp. 1697-1715
Author(s):  
Chunbo Lan ◽  
Yabin Liao ◽  
Guobiao Hu ◽  
Lihua Tang
Keyword(s):  
Equivalent Circuit ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Performance Enhancement ◽  
Damping Ratio ◽  
Power Performance ◽  
Closed Form Solutions ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Power Limit

Nonlinearity has been successfully introduced into piezoelectric energy harvesting for power performance enhancement and bandwidth enlargement. While a great deal of emphasis has been placed by researchers on the structural design and broadband effect, this article is motivated to investigate the maximum power of a representative type of nonlinear piezoelectric energy harvesters, that is, monostable piezoelectric energy harvester. An equivalent circuit is proposed to analytically study and explain system behaviors. The effect of nonlinearity is modeled as a nonlinear stiffness element mechanically and a nonlinear capacitive element electrically. Facilitated by the equivalent circuit, closed-form solutions of power limit and critical electromechanical coupling, that is, minimum coupling to reach the power limit, of monostable piezoelectric energy harvesters are obtained, which are used for a clear explanation of the system behavior. Several important conclusions have been drawn from the analytical analysis and validated by numerical simulations. First, given the same level of external excitation, the monostable piezoelectric energy harvester and its linear counterpart are subjected to the same power limit. Second, while the critical coupling of linear piezoelectric energy harvesters depends on the mechanical damping ratio only, it also depends on the vibration excitation and magnetic field for monostable piezoelectric energy harvesters, which can be used to adjust the power performance of the system.

scholarly journals Improved Multilayered (Bi,Sc)O3-(Pb,Ti)O3 Piezoelectric Energy Harvesters Based on Impedance Matching Technique

Sensors ◽  
2020 ◽  
Vol 20 (7) ◽  
pp. 1958 ◽  
Author(s):  
Bo Su Kim ◽  
Jae-Hoon Ji ◽  
Hong-Tae Kim ◽  
Sung-Jin Kim ◽  
Jung-Hyuk Koh
Keyword(s):  
Energy Harvesting ◽  
Impedance Matching ◽  
Load Resistance ◽  
Mechanical Force ◽  
Output Energy ◽  
Maximum Output ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Matching Technique ◽  
Matching Techniques

As a piezoelectric material, (Bi,Sc)O3-(Pb,Ti)O3 ceramics have been tested and analyzed for sensors and energy harvester applications owing to their relatively high Curie temperature and high piezoelectric coefficient. In this work, we prepared optimized (Bi,Sc)O3-(Pb,Ti)O3 piezoelectric materials through the conventional ceramic process. To increase the output energy, a multilayered structure was proposed and designed, and to obtain the maximum output energy, impedance matching techniques were considered and tested. By varying and measuring the energy harvesting system, we confirmed that the output energies were optimized by varying the load resistance. As the load resistance increased, the output voltage became saturated. Then, we calculated the optimized output power using the electric energy formula. Consequently, we identified the highest output energy of 5.93 µW/cm2 at 3 MΩ for the quadruple-layer harvester and load resistor using the impedance matching system. We characterized and improved the electrical properties of the piezoelectric energy harvesters by introducing impedance matching and performing the modeling of the energy harvesting component. Modeling was conducted for the piezoelectric generator component by introducing the mechanical force dependent voltage sources and load resistors and piezoelectric capacitor connected in parallel. Moreover, the generated output voltages were simulated by introducing an impedance matching technique. This work is designed to explain the modeling of piezoelectric energy harvesters. In this model, the relationship between applied mechanical force and output energy was discussed by employing experimental results and simulation.

Sign in / Sign up

Export Citation Format

Share Document