scholarly journals Mechanosynthesis of MFe2O4 (M = Co, Ni, and Zn) Magnetic Nanoparticles for Pb Removal from Aqueous Solution

2016 ◽  
Vol 2016 ◽  
pp. 1-9 ◽  
Author(s):  
America R. Vazquez-Olmos ◽  
Mohamed Abatal ◽  
Roberto Y. Sato-Berru ◽  
G. K. Pedraza-Basulto ◽  
Valentin Garcia-Vazquez ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Xrd Analysis ◽  
Maximum Adsorption Capacity ◽  
Sorption Behavior ◽  
Order Kinetic ◽  
X Ray ◽  
Isotherm Adsorption ◽  
Crystallite Sizes ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

Adsorption of Pb(II) from aqueous solution using MFe2O4 nanoferrites (M = Co, Ni, and Zn) was studied. Nanoferrite samples were prepared via the mechanochemical method and were characterized by X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), micro-Raman, and vibrating sample magnetometry (VSM). XRD analysis confirms the formation of pure single phases of cubic ferrites with average crystallite sizes of 23.8, 19.4, and 19.2 nm for CoFe2O4, NiFe2O4, and ZnFe2O4, respectively. Only NiFe2O4 and ZnFe2O4 samples show superparamagnetic behavior at room temperature, whereas CoFe2O4 is ferromagnetic. Kinetics and isotherm adsorption studies for adsorption of Pb(II) were carried out. A pseudo-second-order kinetic describes the sorption behavior. The experimental data of the isotherms were well fitted to the Langmuir isotherm model. The maximum adsorption capacity of Pb(II) on the nanoferrites was found to be 20.58, 17.76, and 9.34 mg·g−1 for M = Co, Ni, and Zn, respectively.

Fast Removal of Pb2+ from Aqueous Solution by Water Insoluble Konjac Glucomannan

2009 ◽  
Vol 610-613 ◽  
pp. 65-68 ◽  
Author(s):  
Xue Gang Luo ◽  
Feng Liu ◽  
Xiao Yan Lin
Keyword(s):  
Aqueous Solution ◽  
Correlation Coefficients ◽  
Konjac Glucomannan ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Equilibrium Process ◽  
Fast Removal

Konjac glucomannan (KGM) was converted into water insoluble konjac glucomannan (WIKGM) by treating with NaOH through completely deacetylated reaction. Adsorption study was carried out for the adsorption of Pb2+ from aqueous solution using water insoluble konjac glucomannan. The influences of pH, contact time, temperature and initial Pb2+ concentration on the absorbent were studied. Results of kinetic data showed that the Pb2+ adsorption rate was fast and good correlation coefficients were obtained for the pseudo second-order kinetic model. The equilibrium process was described well by the Langmuir isotherm model with maximum adsorption capacity of 9.18 mg/g on WIKGM at 25°C.

scholarly journals Adsorption of Lead(II) Ions from Aqueous Solution onto Lignin

2009 ◽  
Vol 27 (4) ◽  
pp. 435-445 ◽  
Author(s):  
Laura Bulgariu ◽  
Dumitru Bulgariu ◽  
Theodor Malutan ◽  
Matei Macoveanu
Keyword(s):  
Aqueous Solution ◽  
Ion Concentration ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Solution Ph ◽  
Batch System ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

The adsorption of lead(II) ions from aqueous solution onto lignin was investigated in this study. Thus, the influence of the initial solution pH, the lignin dosage, the initial Pb(II) ion concentration and the contact time were investigated at room temperature (19 ± 0.5 °C) in a batch system. Adsorption equilibrium was approached within 30 min. The adsorption kinetic data could be well described by the pseudo-second-order kinetic model, while the equilibrium data were well fitted using the Langmuir isotherm model. A maximum adsorption capacity of 32.36 mg/g was observed. The results of this study indicate that lignin has the potential to become an effective and economical adsorbent for the removal of Pb(II) ions from industrial wastewaters.

scholarly journals Synthesis, characterization, and evaluation of ZrSiO4/Fe2O3 adsorbent for methylene blue removal in aqueous solutions

2021 ◽  
Vol 882 (1) ◽  
pp. 012019
Author(s):  
T Yuliana ◽  
N Nurlitasari ◽  
A Hardian ◽  
S Budiman ◽  
Jasmansyah ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Order Model ◽  
Textile Waste ◽  
X Ray ◽  
Isotherm Adsorption ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Zircon Sand

Abstract Methylene blue dyes are widely used in textile, batik, plastic, paper, and many other industries. The remain of methylene blue dyes in the textile waste is hazardous for health and the environment. Therefore, it takes effort to deal with it. One of the efforts is the process of adsorption using adsorbents. In this study, the adsorbent ZrSiO4/Fe2O3 was synthesized using the coprecipitation method using NaOH as precipitant. Either ZrSiO4 or Fe2O3 was synthesized from Indonesia mineral local zircon sand and jarosites, respectively. The composites of ZrSiO4/Fe2O3 were prepared in %mole variation, which is 75:25; 50:50; and 25:75. All obtained composites were then characterized using X-Ray Diffraction (XRD). The XRD analysis showed that the crystal structure formed was tetragonal for ZrSiO4 and hexagonal for Fe2O3 (also known as α-Fe2O3). Evaluation toward isotherm adsorption and kinetic adsorption showed that the adsorption of MB using ZrSiO4/Fe2O3 follows the Langmuir isotherm model and pseudo-second-order model, respectively.

scholarly journals Water polishing of phenol by walnut green hull as adsorbent: an insight of adsorption isotherm and kinetic

2016 ◽  
Vol 6 (4) ◽  
pp. 544-552 ◽  
Author(s):  
H. Godini ◽  
F. Hashemi ◽  
L. Mansuri ◽  
M. Sardar ◽  
Ghasem Hassani ◽  
...  
Keyword(s):  
Langmuir Isotherm ◽  
Surface Characteristics ◽  
Xrd Analysis ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Maximum Sorption ◽  
Pseudo Second Order ◽  
Xrd Techniques

The present paper aims to investigate water purification of phenol by walnut green hull adsorbent. The surface characteristics of the adsorbent were studied using Fourier transform infra-red (FTIR), scanning electron microscope, and X-ray diffraction (XRD) techniques. The presence of functional groups such as hydroxyl and carbonyl onto walnut green hull surface was proved by FTIR analysis. Also quartz, cellulose and hematite were detected in the XRD analysis of samples by an X-ray diffractometer. The maximum sorption was achieved at pH 4.0. Data were evaluated for compliance with the Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherm models. The results indicate that the data for adsorption of phenol onto walnut green hull fitted well with the Langmuir isotherm. The maximum adsorption capacity of the adsorbent was achieved by Langmuir isotherm 17.8 mg g–1. Also, the adsorption kinetics of phenol on the adsorbent were studied. The rates of sorption were found to conform to pseudo-second-order kinetics with good correlation.

Study on Adsorption of Cu(II) on Chitosan Nanofiber Membranes

2014 ◽  
Vol 13 (05n06) ◽  
pp. 1460009 ◽  
Author(s):  
Jianhua Cao ◽  
Dongzhou Li ◽  
Weihua Liang ◽  
Dayong Wu
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Ph Effect ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Equilibrium Isotherms ◽  
Electrospinning Technique ◽  
Chitosan Nanofiber ◽  
Pseudo Second Order ◽  
Nanofiber Membranes

Chitosan nanofiber membranes by electrospinning technique were used to remove Cu ( II ) from aqueous solution. The adsorption kinetics, equilibrium isotherms, and pH effect were investigated in batch experiments. The Langmuir isotherm and pseudo second-order kinetic models agree well with the experimental data. The chitosan nanofiber membranes are effective for Cu ( II ) adsorption at pH6. Results showed that the maximum adsorption capacity of the chitosan nanofiber membranes with Cu ( II ) is 118.62 mg g-1. The chitosan nanofiber membranes can be used as an effective adsorbent for the removal of Cu ( II ) in aqueous solution due to high adsorption capacity.

scholarly journals Adsorption of tricresyl phosphate onto graphene nanomaterials from aqueous solution

2017 ◽  
Vol 76 (6) ◽  
pp. 1565-1573 ◽  
Author(s):  
Jun Liu ◽  
Siying Xia ◽  
Xiaomeng Lü ◽  
Hongxiang Shen
Keyword(s):  
Experimental Data ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Tricresyl Phosphate ◽  
Batch Mode ◽  
Order Kinetic Model ◽  
Endothermic Process ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Increasing Temperature

Phosphorus flame retardant tricresyl phosphate (TCP) adsorption on graphene nanomaterials from aqueous solutions was explored using batch and column modes. Comparative studies were performed regarding the kinetics and equilibrium of TCP adsorption on graphene oxide (GO) and graphene (G) in batch mode. The adsorption kinetics exhibited a rapid TCP uptake, and experimental data were well described by the pseudo-second-order kinetic model. Adsorption isotherm data of TCP on the two adsorbents displayed an improved TCP removal performance with increasing temperature at pH 5, while experimental data were well described by the Langmuir isotherm model with a maximum adsorption capacity of 87.7 mg·g−1 for G, and 30.7 mg·g−1 for GO) at 303 K. The thermodynamic parameters show that the adsorption reaction is a spontaneous and endothermic process. In addition, dynamic adsorption of TCP in a fixed G column confirmed a faster approach to breakthrough at high flow rate, high influent TCP concentration, and low filling height of adsorbent. Breakthrough data were successfully described by the Thomas and Yoon-Nelson models.

scholarly journals REMOVAL OF Pb2+ FROM AQUEOUS SOLUTION BY ADSORPTION ONTO COMPOSITE BASED ON EUCALYPTUS LEAF AND POLYANILINE

2017 ◽  
Vol 55 (1) ◽  
pp. 54
Author(s):  
Le Cao The ◽  
Vu Minh Tan ◽  
Phan Thi Binh
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Sem Images ◽  
Adsorption Data ◽  
Freundlich Adsorption Isotherm ◽  
Pseudo Second Order ◽  
Ir Analysis ◽  
Polymerization Method

Composite based on eucalyptus leaf and polyaniline (EL-PANi) was prepared by chemical polymerization method. It showed that the function groups belonging to polyaniline and eucalyptus leaf were found through IR analysis and the nanostructure of composite was explained by SEM images. The adsorption of  Pb2+ was carried out onto composite in aqueous solution via varying pH, contact time, and its initial concentration. The experimental adsorption data fitted well into Freundlich adsorption isotherm model (r2 = 0.9873). The adsorption process followed pseudo-second order kinetic with r2 = 0.9995. The maximum adsorption capacity of Pb2+ onto that composite was 172.4138 mg/g  by Langmuir equation and KF was 58.7527 mg/g by Freundlich one.

Thermal Activation of Brazilian Smectite Clay (Primavera) and its Application for the Removal of Cadmium from Aqueous Solution

2020 ◽  
Vol 07 ◽  
Author(s):  
Marta Lígia Pereira da Silva ◽  
Tellys Lins Almeida Barbosa ◽  
Meiry Gláucia Freire Rodrigues
Keyword(s):  
Aqueous Solution ◽  
Kinetic Constant ◽  
Second Order ◽  
Order Kinetic ◽  
Experimental Conditions ◽  
X Ray ◽  
Thermally Activated ◽  
Study Results ◽  
Water Cleaning ◽  
Pseudo Second Order

Background: Region-based solutions for water cleaning could be critical to tackle the water challenges faced in enhancing the in the future. Brazilian Primavera clay is cheap, abundant, and an untested material that has the potential to be used for water cleaning. Objective: the objective of the present work was to thermally activate and characterize the Brazilian clay and then determine the potential to remove Cd2+ from an aqueous solution. Methods: Primavera clay was thermally activated at 300 oC and characterized using X ray diffraction, X-ray Spectroscopy Energy Dispersive, and N2 adsorption. Sorption equilibrium was determined using the following experimental conditions: constant pH 4.5, 5 h, and 27 oC. Langmuir, Freundlich, Dubinin-Radushkevich and Temkin isotherms models were applied in order to determine the efficiency of clay used as an adsorbent. Adsorption kinetics was analyzed using the pseudo-second-order kinetic model. Results: In this study, results revealed that even though the heat treatment did not cause profound alterations on the clay structure(smectite) and surface area (78 m2 /g), a pseudo-second-order kinetic constant of 0.5563 mg/g/min was found for the cadmium removal. Conclusion: The mathematical models of the Langmuir and Temkin showed a better fit to the experimental data. A high affinity between the cadmium and the thermally activated Primavera clay was found up to 88 % with removal efficiencies.

Preparation of copper aluminum-biochar composite as adsorbent of malachite green in aqueous solution

2020 ◽  
Author(s):  
Neza Rahayu Palapa ◽  
Tarmizi Taher ◽  
Risfidian Mohadi ◽  
Addy Rachmat ◽  
Aldes Lesbani
Keyword(s):  
Aqueous Solution ◽  
Composite Material ◽  
Malachite Green ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
X Ray ◽  
Pseudo Second Order ◽  
Edx Analyses ◽  
Copper Aluminum ◽  
Regeneration Study

Abstract In this work, CuAl/Biochar (BC) composite was prepared by the coprecipitation method. The materials were applied to remove malachite green in aqueous solution. These materials were characterized using XRD, FTIR, BET and SEM-EDX analyses. The composite material was confirmed by X-ray diffractograms with reflection (002) at 24o and the appearance of new peaks at 1095 cm -1 . The BET result of CuAl/BC composite has larger surface area is 168 m 2 /g than 46 m 2 /g for LDH. The morphologies of composite materials show agglomeration and micro particle size. The result of the adsorption study indicated the composite material follows pseudo-second-order (PSO) and Langmuir isotherm models. The maximum adsorption capacity of malachite green using CuAl/BC uptake is 164.316 mg/g. The thermodynamic analysis indicates that the malachite green adsorption is spontaneous, endothermic. Regeneration study of adsorbent CuAl/BC composite shows after four times reused, it still has high removal efficiency at 89%.

scholarly journals Steel slag as low-cost adsorbent for the removal of phenanthrene and naphthalene

2018 ◽  
Vol 36 (3-4) ◽  
pp. 1160-1177 ◽  
Author(s):  
Liyun Yang ◽  
Xiaoming Qian ◽  
Zhi Wang ◽  
Yuan Li ◽  
Hao Bai ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Low Cost ◽  
Steel Slag ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Batch Experiments ◽  
Obvious Effect ◽  
X Ray ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model

This study investigates the removal effectiveness and characteristics of phenanthrene and naphthalene using low-cost steel slag with batch experiments. The adsorption characteristics of steel slag were measured and analysed using X-ray fluorescence, X-ray diffraction, and Fourier transform infrared spectroscopy. The batch experiments investigated the effect of the time gradient, pH, and steel slag dosage gradient on the adsorption of the steel slag. The results show that with time and dosage of steel slag increased, the adsorption capacity of phenanthrene and naphthalene increased and gradually became balanced, but pH had no obvious effect on the adsorption of phenanthrene and naphthalene. The Langmuir isotherm model best describes the phenanthrene and naphthalene removal by the steel slag, which shows the adsorption occurring in a monolayer. The maximum adsorption capacity of the steel slag to phenanthrene and naphthalene is 0.043 and 0.041 mg/g, respectively. A pseudo-first-order kinetic model can better represent the adsorption of phenanthrene and naphthalene by steel slag. The research demonstrates that the steel slag has a certain adsorption capacity for phenanthrene and naphthalene.

Sign in / Sign up

Export Citation Format

Share Document