Shape Memory Characteristics and Superelasticity of Ti-Ni-Cu Alloy Ribbons with Nano Ti2Ni Particles

2008 ◽  
Vol 8 (2) ◽  
pp. 722-727 ◽  
Author(s):  
Tae-hyun Nam ◽  
Cheol-am Yu ◽  
Jung-min Nam ◽  
Hyun-gon Kim ◽  
Yeon-wook Kim
Keyword(s):  
Melt Spinning ◽  
Volume Fraction ◽  
Deformation Behaviour ◽  
Parent Phase ◽  
Tensile Tests ◽  
Constant Load ◽  
Cu Alloy ◽  
Transmission Electron ◽  
Average Size ◽  
Memory Characteristics

Microstructures and deformation behaviour of Ti-45Ni-5Cu and Ti-46Ni-5Cu alloy ribbons prepared by melt spinning were investigated by transmission electron microscopy, thermal cycling tests under constant load and tensile tests. Spherical Ti2Ni particles coherent with the B2 parent phase were observed in the alloy ribbons when the melt spinning temperature was higher than 1773 K. Average size of Ti2Ni particles in the ribbons obtained at 1873 K was 8 nm, which was smaller than that (10 nm) in the ribbons obtained at 1773 K. Volume fraction of Ti2Ni phase in the ribbons obtained at 1873 K was 40%, which was larger than that (20%) in the ribbons obtained at 1773 K. The stress required at temperatures of Af + 10 K for the stress-induced martensitic transformation increased from 93 MPa to 229 MPa and apparent elastic modulus of the B2 parent phase increased from 56 GPa to 250 GPa with increasing the melt spinning temperature from 1673 K to 1873 K in Ti-45Ni-5Cu alloy ribbons. The critical stress for slip deformation of the ribbons increased by coherent Ti2Ni particles, and thus residual elongation did not occur even at 160 MPa, while considerable plastic deformation occurred at 60 MPa in the ribbons without Ti2Ni particles. Almost perfect superelastic recovery was found in the ribbons with coherent Ti2Ni particles, while only partial superelastic recovery was observed in the ribbons without coherent Ti2Ni particles.

Microstructure and Tensile Behavior of Ti-Rich Ti-Ni-Cu Melt-Spun Ribbon

2014 ◽  
Vol 936 ◽  
pp. 1163-1167
Author(s):  
Wen Jun He ◽  
Guang Hui Min ◽  
Oleg Tolochko
Keyword(s):  
Melt Spinning ◽  
Tensile Deformation ◽  
Amorphous Ribbon ◽  
Fracture Morphology ◽  
Tensile Tests ◽  
Tensile Fracture ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Annealed Ribbon ◽  
Martensitic State

Microstructure and mechanical properties of Ti51.5Ni25Cu23.5 ribbon fabricated by melt spinning were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM) and tensile tests. Some B19 martensite crystalline with (011) compound twin was embedded in the mainly amorphous ribbon, while the ribbon annealed at 450°C for 1 h is at fully martensitic state. Annealing process alter the preferential orientation from (022)-B19 to (111)-B19. Tensile fracture stresses of as-spun ribbon and the annealed ribbon are 1257 MPa and 250 MPa, respectively. The tensile fracture morphology of as-spun ribbon shows typical vein fringe while that of the annealed ribbon reveals fine but depth-inhomogeneous dimples. After tensile deformation, the annealed ribbon exhibits typical martensitic detwinning behavior accompanying with the strain contrast.

Transformation Behavior and Shape Memory Characteristics of Ti-45Ni-5Cu(at%) Alloy Ribbons Fabricated by Melt Spinning

2004 ◽  
Vol 449-452 ◽  
pp. 1093-1096 ◽  
Author(s):  
Tae Hyun Nam ◽  
Jae Hwa Lee ◽  
Tae Yeon Kim ◽  
Yeon Wook Kim
Keyword(s):  
Shape Memory ◽  
Melt Spinning ◽  
Constant Load ◽  
X Ray Diffraction ◽  
Transformation Behavior ◽  
X Ray ◽  
Density Of Dislocations ◽  
Large Lattice ◽  
One Step ◽  
Memory Characteristics

Transformation behaviors and shape memory characteristics of Ti-45Ni-5Cu alloy ribbons fabricated by melt spinning were investigated by means of optical microscopy, differential scanning calorimetries(DSC), X-ray diffraction and thermal cycling tests under constant load. They depended largely on temperatures of liquid metal. The B2-B19-B19’ two-step transformation occurred in the ribbons fabricated with the liquid whose temperature was higher than 1723 K, while the B2-B19’ one-step transformation occurred in the ribbons with the liquid at 1673 K. The stabilization of the B19 martensite in Ti-45Ni-5Cu alloy ribbons was ascribed to the high density of dislocations which made strong resistance to large lattice deformation associated with a formation of the B19’ martensite.

Precipitation Studies of Undeformed and ECAP-Deformed Al-4%Cu Alloys: Effects on Microstructure and Tensile Properties

2008 ◽  
Vol 584-586 ◽  
pp. 708-715 ◽  
Author(s):  
Erika Fernanda Prados ◽  
Vitor Luiz Sordi ◽  
Maurizio Ferrante
Keyword(s):  
Initial Conditions ◽  
Tensile Tests ◽  
Solution Temperature ◽  
Tensile Behaviour ◽  
Total Strength ◽  
Angular Pressing ◽  
Cu Alloy ◽  
Transmission Electron ◽  
Heat Treated ◽  
Precipitation Heat

The present study is an assessment of the effects of precipitation heat treatments on tensile behaviour, work hardening (WH) characteristics and microstructural evolution of an Al-4%Cu alloy deformed by equal channel angular pressing (ECAP). Two ageing temperatures were employed (170 and 100oC) and their effect on strength and WH behaviour was compared with that exerted on the same alloy, but in two different initial conditions: quenched from solution temperature and slowly cooled before anneal. Grain and precipitate sizes of samples deformed by one and four ECAP passes and heat treated as described were measured employing transmission electron microscopy (TEM). It was concluded that the lower ageing temperature gives the best combination of strength and ductility, a high WH rate and, possibly, the smaller grain and precipitate sizes. The relative participation of the various hardening mechanisms to total strength was estimated from tensile tests and hardness measurements.

Precipitation Sequence and Kinetics in an Fe-Si-Ti Alloy

2011 ◽  
Vol 172-174 ◽  
pp. 833-838 ◽  
Author(s):  
Malika Perrier ◽  
Alexis Deschamps ◽  
Patricia Donnadieu ◽  
Frédéric de Geuser ◽  
Frédéric Danoix ◽  
...  
Keyword(s):  
Volume Fraction ◽  
High Volume ◽  
Tensile Tests ◽  
Atom Probe ◽  
Precipitate Size ◽  
Precipitation Sequence ◽  
Precipitation Kinetics ◽  
Temperature Range ◽  
Transmission Electron ◽  
Temporary Decrease

The Fe-Si-Ti system is known to show nanoscale precipitation of the Fe2SiTi Heusler phase with potentially high volume fraction (~4%), very high density and a size ranging from 1 to 20nm after artificial aging. The strong hardening potential of these precipitates make these steels candidates for automotive applications; however no understanding of the precipitation sequence (competition with other phases) nor the precipitation kinetics are available. The present study presents a quantitative study of the precipitation kinetics (size, volume fraction and number density) in a wide temperature range (450-800°C), realised by coupling systematically Small Angle Neutron Scattering (SANS), Transmission Electron microscopy (TEM) and Tomographic Atom Probe (TAP). Tensile tests were also carried out so as to determine the microstructure/properties relationships. Along the complete temperature range, it is shown that a compromise between time for precipitation and small precipitate sizes can be reached around 550°C. At this intermediate temperature, precipitation is shown to occur in two steps, linked with a second nucleation process after nucleation & growth of the first family of Fe2SiTi has been completed. This second precipitation step results in a temporary decrease in precipitate size and an increase in hardness. The nature of these precipitates is discussed in view of the TEM and TAP observations.

scholarly journals Microstructural Features of Strain-Induced Martensitic Transformation in Medium-Mn Steels with Metastable Retained Austenite/ Cechy Mikrostrukturalne Indukowanej Odkształceniem Przemiany Martenzytycznej W Stalach Sredniomanganowych Z Metastabilnym Austenitem Szczątkowym

2014 ◽  
Vol 59 (4) ◽  
pp. 1673-1678 ◽  
Author(s):  
A. Grajcar ◽  
A. Kilarski ◽  
K. Radwanski ◽  
R. Swadzba
Keyword(s):  
Electron Microscopy ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Electron Backscatter Diffraction ◽  
Bainitic Ferrite ◽  
Tensile Tests ◽  
Bainitic Steels ◽  
Transmission Electron ◽  
Strain Induced Martensite ◽  
Backscatter Diffraction

Abstract The work addresses relationships between the microstructure evolution and mechanical properties of two thermomechanically processed bainitic steels containing 3 and 5% Mn. The steels contain blocky-type and interlath metastable retained austenite embeded between laths of bainitic ferrite. To monitor the transformation behaviour of retained austenite into strain-induced martensite tensile tests were interrupted at 5%, 10%, and rupture strain. The identification of retained austenite and strain-induced martensite was carried out using light microscopy (LM), scanning electron microscopy (SEM) equipped with EBSD (Electron Backscatter Diffraction) and transmission electron microscopy (TEM). The amount of retained austenite was determined by XRD. It was found that the increase of Mn addition from 3 to 5% detrimentally decreases a volume fraction of retained austenite, its carbon content, and ductility.

Shape Memory Effect and Superelasticity of an Equiatomic Ti-Ni Alloy with Surface Sulfide Layers

2006 ◽  
Vol 510-511 ◽  
pp. 262-265
Author(s):  
Tae Hyun Nam ◽  
Shin Goo Hur ◽  
Jae Hwa Lee ◽  
Gyu Bong Cho
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Martensitic Transformation ◽  
Shape Memory ◽  
Tensile Tests ◽  
Constant Load ◽  
Ni Alloy ◽  
Memory Characteristics ◽  
Scanning Electron ◽  
Start Temperature

Shape memory characteristics and superelasticity of an equiatomic Ti-Ni alloy with surface sulfide layers were investigated by means of thermal cycling tests under constant load, tensile tests, and scanning electron microscopy. Martensitic transformation start temperature (Ms) increased by sulfidation, which is ascribed to a compressive stress imposed by surface sulfide layers. Surface sulfide layers were found to make transformation elongation be small when their thickness was less than 5 ㎛. This is ascribed to the fact that the surface sulfide layers were not detached from substrates and constrained martensitic transformation. When thickness of the surface sulfide layers was 35 ㎛, transformation elongation was not affected by them because they were detached during transformation. Superelastic recovery decreased by the sulfide layers when their thickness was about 5 ㎛, while it did not change when the thickness was about 35 ㎛.

Fracture Analysis and Mechanical Properties of Magnesium Based Composites

2017 ◽  
Vol 891 ◽  
pp. 526-532 ◽  
Author(s):  
Beáta Ballóková ◽  
Dagmar Jakubéczyová
Keyword(s):  
Mechanical Properties ◽  
Volume Fraction ◽  
Tensile Tests ◽  
Fracture Analysis ◽  
Physical Parameters ◽  
Weight Percentage ◽  
Matrix Microstructure ◽  
Angular Pressing ◽  
The Matrix ◽  
Average Size

Mechanical properties and microstructure and fracture analysis of a magnesium alloys based composite series with different volume fraction of alumina dispersoid nanoparticles were studied. The initial states of the composites were further treated by severe plastic deformation (SPD) using equal channel angular pressing (ECAP) in order to achieve microstructures with very fine grains of matrix. Microstructure parameters, in particular the matrix grain size, average size of the dispersed particles and their distribution, were observed using optical microscopy. The average grain sizes of MMCs decreased evidently with the increase of the weight percentage of Al2O3 particles additions and ECAP passes. The heat deformation process of such materials, besides the formation of incorporated Al2O3 particles, also leads to the creation of intermetallic compound Mg17Al12. Fracture surfaces after tensile tests at room and elevated temperature were studied by SEM. The fracture of studying materials were characterized as the ductile fracture due to the existence of a large number of dimples.In summary, it has been shown that mechanical properties are affected by lattice, physical parameters of phases within the composite systems. They are also affected by microstructure and substructure, which depend on the technology of compaction and densification.

Formation of Platinum Nanodendrites Embedded Organic Insulator for Memory Application

2014 ◽  
Vol 1024 ◽  
pp. 44-47 ◽  
Author(s):  
Nur Syafinaz Ridhuan ◽  
Nabil Iman Muzzafaruddin ◽  
Abdul Razak Khairunisak ◽  
K.C. Aw
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Reduction Method ◽  
Chemical Reduction ◽  
Chemical Reduction Method ◽  
Growth Duration ◽  
X Ray ◽  
Transmission Electron ◽  
Average Size ◽  
Memory Characteristics

This work describes the formation of platinum nanodendrites (PtNDs) using the chemical reduction method. The PtNDs were formed with varying concentration of K2PtCl4 precursor (5-20 mM) and growth duration (8-16 min). The optimum concentration of K2PtCl4 was 15 mM whereby high crystalline nanodendrites with an average size of 118 nm were produced. Aggregation of nanodendrites occurred when the growth duration was prolonged to more than 12 minutes. The morphology and size of PtNDs were characterized by using a transmission electron microscope (TEM), high resolution transmission electron microscope (HRTEM) and X-ray diffractometer (XRD). Additionally, the memory characteristics of PtNDs embedded in polymethylsilsesquioxanes (PMSSQ)/Si with gold electrodes were studied in this work. PtNDs played a role as charge-trapped sites and showed good memory effect when embedded in PMSSQ. Optimum memory properties of PMSSQ-embedded PtNDs were obtained for PtNDs synthesized with 15 mM K2PtCl4 concentration at 12 min of growth duration with 170 electrons trapped per PtNDs and Vth of 2.8 V.

scholarly journals Role of refractory elements in near-alpha titanium alloys on high temperature mechanical properties

2020 ◽  
Vol 321 ◽  
pp. 04018
Author(s):  
Z. Huvelin ◽  
C. Gouroglian ◽  
N. Horézana ◽  
S. Naka
Keyword(s):  
Volume Fraction ◽  
Solution Treatment ◽  
Aging Treatment ◽  
Tensile Tests ◽  
Alpha Phase ◽  
Air Cooling ◽  
Creep Tests ◽  
High Temperature Mechanical Properties ◽  
Refractory Elements ◽  
Average Size

The effect of Tungsten (W), Tantalum (Ta) and simultaneous addition of Germanium (Ge) and Silicon (Si) on the microstructure evolution, tensile and creep properties of the near-alpha alloy Ti-5.7Al-3.9Sn-3.7Zr-0.7Nb-0.5Mo-0.35Si-0.05C have been investigated at high temperatures up to 650°C. Microstructural characterizations following solution treatment at 1050°C for 2 hours with oil quenching and aging treatment at 700°C for 2 hours followed by air cooling, highlighted that the additions of refractory elements such as W and Ta led to a decrease of both the volume fraction of the primary alpha phase (ap) and its average size. Tensile tests performed up to 650°C revealed a significant improvement in tensile strength with additions of W and Ta, even though a decrease of ductility has been also detected. Creep tests carried out at 600°C under a constant stress of 200 MPa pointed out that, refractory elements, Ge and Si have a beneficial effect on both primary and steady-state creep strain rates.

scholarly journals A study on the effect of nano-precipitates on fracture behavior of nano-structured Al-2wt%Cu alloy fabricated by accumulative roll bonding (ARB) process

2016 ◽  
Vol 52 (1) ◽  
pp. 93-98 ◽  
Author(s):  
B. Azad ◽  
E. Borhani
Keyword(s):  
Electron Microscope ◽  
Accumulative Roll Bonding ◽  
Average Particle Size ◽  
Void Coalescence ◽  
Average Particle ◽  
Roll Bonding ◽  
Cu Alloy ◽  
Transmission Electron ◽  
Mean Grain Size ◽  
Average Size

An Al-2wt%Cu alloy was subjected to accumulative roll bonding (ARB) process up to a strain of 4.8. The two kinds of different microstructures, i.e, solution treated (ST) one and 190?C pre-aged for 30 min (Aged), were prepared as the starting structures for the ARB process. The microstructures were studied by transmission electron microscope (TEM) and electron backscattering diffraction (EBSD). The results showed that the fine precipitates having the average particle size of 16 nm were formed after aging process. On the other hand, the mean grain size of the ST-ARB and the Aged-ARB specimens reached to 650 nm and 420 nm, respectively. Study of the fracture surfaces were carried out by scanning electron microscope (SEM). The results indicated that at 0-cycle ARB, the specimens show dimples indicating the micro-void coalescence (MVC) mechanism of ductile fracture. The average size of dimples was larger in the ST-ARB specimen compared to the Aged-ARB specimen. The fracture mode was transgranular cleavage fracture in the Aged-specimen. At 3- cycle and 6-cycle ARB, also the specimens showed cleavage facets and river lines, that the river lines or the stress lines are steps between cleavage or parallel planes, which are always converged in the direction of local crack propagation.

Sign in / Sign up

Export Citation Format

Share Document