Impact of quasi-isotropic raster layup on the mechanical behaviour of fused filament fabrication parts

2021 ◽  
pp. 095400832110419
Author(s):  
Lovin K John ◽  
Ramu Murugan ◽  
Sarat Singamneni
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Mechanical Strength ◽  
Process Parameters ◽  
Mechanical Behaviour ◽  
Fused Filament Fabrication ◽  
Anisotropic Behaviour ◽  
Oriented Samples ◽  
Weak Interlayer ◽  
Special Concern

The development of fused filament fabrication has extended the range of application of additive manufacturing in various areas of research. However, the mechanical strength of the fused filament fabrication–printed parts were considerably lower than that of parts fabricated by other conventional methods, owing to the observed anisotropic behaviour and formation of voids by weak interlayer diffusion. Intense studies on the effect of design and process parameters of the printed parts on the mechanical properties have been done, whereas studies on the effect of build orientations and raster patterns needs special concern. The main aim of this work is to fabricate parts printed using quasi-isotropic laminate arrangement of rasters, achieved by a raster layup of [45/0/−45/90]s, and to compare their mechanical properties with those of the commonly used 0°/90° (cross) and 45°/−45° (crisscross) raster oriented parts. The quasi-isotropic–oriented samples were observed with improved mechanical behaviour in tensile, compressive, flexural and impact tests compared to the commonly employed raster orientations.

scholarly journals Suitability of Recycled PLA Filament Application in Fused Filament Fabrication Process

2021 ◽  
Vol 15 (4) ◽  
pp. 491-497
Author(s):  
Tomislav Breški ◽  
Lukas Hentschel ◽  
Damir Godec ◽  
Ivica Đuretek
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Polylactic Acid ◽  
Design Of Experiment ◽  
Experimental Approach ◽  
Manufacturing Processes ◽  
Support Structures ◽  
Fused Filament Fabrication ◽  
Layer Height ◽  
Printing Parameters

Fused filament fabrication (FFF) is currently one of the most popular additive manufacturing processes due to its simplicity and low running and material costs. Support structures, which are necessary for overhanging surfaces during production, in most cases need to be manually removed and as such, they become waste material. In this paper, experimental approach is utilised in order to assess suitability of recycling support structures into recycled filament for FFF process. Mechanical properties of standardized specimens made from recycled polylactic acid (PLA) filament as well as influence of layer height and infill density on those properties were investigated. Optimal printing parameters for recycled PLA filaments are determined with Design of Experiment methods (DOE).

Microstructural and Mechanical Properties of a Solid-State Additive Manufactured Magnesium Alloy

2021 ◽  
pp. 1-21
Author(s):  
Thomas Robinson ◽  
Malcolm Williams ◽  
Harish Rao ◽  
Ryan P. Kinser ◽  
Paul Allison ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Solid State ◽  
Magnesium Alloy ◽  
Magnesium Alloys ◽  
Process Parameters ◽  
Weight Ratio ◽  
Structural Components ◽  
Friction Stir ◽  
Magnesium Alloy Az31b

Abstract In recent years, additive manufacturing (AM) has gained prominence in rapid prototyping and production of structural components with complex geometries. Magnesium alloys, whose strength-to-weight ratio is superior compared to steel and aluminum alloys, have shown potential in lightweighting applications. However, commercial beam-based AM technologies have limited success with magnesium alloys due to vaporization and hot cracking. Therefore, as an alternative approach, we propose the use of a near net-shape solid-state additive manufacturing process, Additive Friction Stir Deposition (AFSD), to fabricate magnesium alloys in bulk. In this study, a parametric investigation was performed to quantify the effect of process parameters on AFSD build quality including volumetric defects and surface quality in magnesium alloy AZ31B. In order to understand the effect of the AFSD process on structural integrity in the magnesium alloy AZ31B, in-depth microstructure and mechanical property characterization was conducted on a bulk AFSD build fabricated with a set of acceptable process parameters. Results of the microstructure analysis of the as-deposited AFSD build revealed bulk microstructure similar to wrought magnesium alloy AZ31 plate. Additionally, similar hardness measurements were found in AFSD build compared to control wrought specimens. While tensile test results of the as-deposited AFSD build exhibited a 20 percent drop in yield strength, nearly identical ultimate strength was observed compared to the wrought control. The experimental results of this study illustrate the potential of using the AFSD process to additively manufacture Mg alloys for load bearing structural components with achieving wrought-like microstructure and mechanical properties.

Variance Quantification of Different Additive Manufacturing Processes for Acoustic Meta Materials

2021 ◽  
Vol 263 (4) ◽  
pp. 2708-2723
Author(s):  
Manuel Bopp ◽  
Arn Joerger ◽  
Matthias Behrendt ◽  
Albert Albers
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Production Process ◽  
Laser Scanning ◽  
Mode Shapes ◽  
Manufacturing Processes ◽  
3D Laser Scanning ◽  
Fused Filament Fabrication ◽  
Manufacturing Techniques ◽  
Different Levels

Many concepts for acoustic meta materials rely on additive manufacturing techniques. Depending on the production process and material of choice, different levels of precision and repeatability can be achieved. In addition, different materials have different mechanical properties, many of which are frequency dependent and cannot easily be measured directly. In this contribution the authors have designed different resonator elements, which have been manufactured utilizing Fused Filament Fabrication with ABSplus and PLA, as well as PolyJet Fabrication with VeroWhitePlus. All structures are computed in FEA to obtain the calculated Eigenfrequencies and mode shapes, with the respective literature values for each material. Furthermore, the dynamic behavior of multiple instances of each structure is measured utilizing a 3D-Laser-Scanning Vibrometer under shaker excitation, to obtain the actual Eigenfrequencies and mode shapes. The results are then analyzed in regards to variance between different print instances, and in regards to accordance between measured and calculated results. Based on previous work and this analysis the parameters of the FEA models are updated to improve the result quality.

scholarly journals Effect of Interlayer Cooling on the Preparation of Ni-Based Coatings on Ductile Iron

Coatings ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 544
Author(s):  
Yuyu He ◽  
Yijian Liu ◽  
Jiquan Yang ◽  
Fei Xie ◽  
Wuyun Huang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Additive Manufacturing ◽  
Dilution Rate ◽  
Process Parameters ◽  
Ductile Iron ◽  
Storage Effect ◽  
Thickness Increase ◽  
Average Grain Size ◽  
Metal Additive

In metal additive manufacturing without interlayer cooling, the macro-size of the layer itself is difficult to control due to the thermal storage effect. The effect of interlayer cooling was studied by cladding Ni-based coatings on the substrate of ductile iron. The results show that under the same process parameters, compared with non-interlayer cooling deposition, the dilution rate is better, and the thickness increase of interlayer cooling deposition is more uniform, which is conducive to controlling the macro-size of the interlayer cooling deposition. Furthermore, interlayer cooling deposition has fewer impurities and more uniform microstructures. Moreover, the average grain size is refined and the dendrite growth is inhibited, which improves the mechanical properties of the coating. Therefore, the hardness of the interlayer cooling specimens is greater than that of the non-interlayer-cooled specimens.

Additive Manufacturing of Nickel-Based Superalloys

2018 ◽  
Author(s):  
Benjamin Graybill ◽  
Ming Li ◽  
David Malawey ◽  
Chao Ma ◽  
Juan-Manuel Alvarado-Orozco ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Process Parameters ◽  
High Performance ◽  
Structural Integrity ◽  
Elevated Temperatures ◽  
Secondary Phases ◽  
Treatment Regimens ◽  
Operating Environments ◽  
Manufacturing Technologies

Additive manufacturing enables the design of components with intricate geometries that can be manufactured with lead times much shorter when compared with conventional manufacturing. The ability to manufacture components out of high-performance metals through additive manufacturing technologies attracts industries that wish to develop more complex parts, but require components to maintain their structural integrity in demanding operating environments. Nickel-based superalloys are of particular interest due to their excellent mechanical, creep, wear, and oxidation properties at both ambient and elevated temperatures. However, relationship between process parameters and the resulting microstructure is still not well understood. The control of the microstructure, in particular the precipitation of secondary phases, is of critical importance to the performance of nickel-based superalloys. This paper reviews the additive manufacturing methods used to process nickel-based superalloys, the influence of the process parameters on microstructure and mechanical properties, the effectiveness of various heat treatment regimens, and the addition of particles in order to further improve mechanical properties.

An Investigation of Effective Process Parameters on Phase Transformation Temperature of Nitinol Manufactured by Selective Laser Melting

2014 ◽  
Author(s):  
Mohsen Taheri Andani ◽  
Christoph Haberland ◽  
Jason Walker ◽  
Mohammad Elahinia
Keyword(s):  
Mechanical Properties ◽  
Material Processing ◽  
Phase Transformation ◽  
Additive Manufacturing ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Energy Input ◽  
Phase Transformation Temperature ◽  
Shape Memory Material ◽  
Laser Melting

It’s well accepted that the thermo-mechanical properties of Nitinol (NiTi) are strongly affected by the material processing. Additive manufacturing has been recently considered as an interesting technique to develop Nitinol devices with sophisticated geometries, which are impossible or very difficult to be produced through typical manufacturing procedures. In the present work, the effect of energy input on the phase transformation temperatures, as the most critical thermal parameters of the shape memory material, of Nitinol parts manufactured by selective laser melting is investigated and discussed.

scholarly journals Synthesis and Properties of Electroconductive Polymeric Composite Material Based on Polypyrrole

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
N. S. Ilicheva ◽  
N. K. Kitaeva ◽  
V. R. Duflot ◽  
V. I. Kabanova
Keyword(s):  
Mechanical Properties ◽  
Composite Material ◽  
Mechanical Strength ◽  
Process Parameters ◽  
Physical And Mechanical Properties ◽  
Polymeric Composite ◽  
Polymeric Composite Material ◽  
Elastic Composite ◽  
The Relationship

A technique is proposed for obtaining electroconductive, mechanically strong, and elastic composite material based on polypyrrole and hydrophilized polyethylene. The relationship is established between the process parameters and properties of the composite material such as electroconductivity and mechanical strength. Several methods are considered in the view of increasing electroconductivity of the material. Physical and mechanical properties of the composite material are investigated.

Sign in / Sign up

Export Citation Format

Share Document