Effect of operating parameters on functional fatigue characteristics of an Ni-Ti shape memory alloy on partial thermomechanical cycling

2022 ◽  
pp. 1045389X2110722
Author(s):  
Swaminathan Ganesan ◽  
Sampath Vedamanickam
Keyword(s):  
Yield Strength ◽  
Applied Stress ◽  
Stress Level ◽  
Crack Nucleation ◽  
Maximum Temperature ◽  
Thermomechanical Cycling ◽  
Permanent Strain ◽  
A Value ◽  
The Stability ◽  
Cycle Temperature

In this study, the influence of upper cycle temperature (maximum temperature in a cycle) and the magnitude of applied stress on the functional properties of an SMA during partial thermomechanical cycling has been studied. A near-equiatomic NiTi SMA was chosen and tested under different upper cycle temperatures (between martensite finish (Mf) and austenite finish (Af) temperatures) and stress level (below and above the yield strength of the martensite). The upper cycle temperature was varied by controlling the magnitude of the current supply. The results show that a raise in the upper cycle temperature causes the permanent strain to increase and also lowers the stability. However, decreasing the stress imposed to a value lower than the yield strength of the martensite improves cyclic stability. The upper cycle temperature was found to influence the crack nucleation, whereas the applied stress level the crack propagation during partial thermomechanical cycling of SMAs. Therefore, decreasing the upper cycle temperature as well as the magnitude of stress applied to lower than the yield stress of martensite have been found to be suitable strategies for increasing the lifespan of SMA-based actuators during partial thermomechanical cycling.

scholarly journals The use of flat-ended projectiles for determining dynamic yield stress - II. Tests on various metallic materials

1948 ◽  
Vol 194 (1038) ◽  
pp. 300-322 ◽  
Keyword(s):  
Yield Strength ◽  
Dynamic Strength ◽  
Soft Materials ◽  
Static Strength ◽  
Compressive Yield Strength ◽  
Dynamic Tests ◽  
Pure Lead ◽  
Permanent Strain ◽  
Yield Values ◽  
Static Conditions

A description is given of the experimental technique devised to apply the method outlined theoretically in part I to the measurement of the dynamic compressive yield strength of various steels, duralumin, copper, lead, iron and silver. A polished piece of armour steel was employed as a target, and cylindrical specimens were fired at it at various measured velocities from Service weapons. The distance between the weapon and target was made short to ensure normal impact, and apparatus was devised for the precise measurement of striking velocity over this short range. The dynamic compressive yield strength was computed from the density of the specimen, the striking velocity, and from measurements of the dimensions of the test piece before and after test. Details are given of the accuracy of the various measurements, and of their effect on the values of yield strength. The method was found to be inaccurate at low and high velocities. For instance, with mild steel, satisfactory results were only obtainable within the range 400 to 2500 ft. /sec. The range of velocities within which satisfactory results could be obtained varied with the quality of the material tested, soft metals giving results within a much lower range than that necessary for harder materials. Because of its failure at low velocities, the method could not be employed to bridge the gap between static and dynamic tests. The rate of strain employed in the dynamic tests could not be measured, but was estimated to be of the order of 10,000 in. /in. /sec. With the materials tested little change of dynamic strength occurred within the range of striking velocities employed, probably because the rate of strain did not vary to any great extent with the striking velocity. Within the range of weapons available, that is, from a 0·303 in. rifle up to a 13 pdr. gun (calibre 3·12 in.), little change of dynamic strength occurred with alteration of the initial dimensions of the specimens, probably because the corresponding change of rate of strain was not large. In general, the dynamic compressive yield strength S was greater than the static strength Y represented by the compressive stress giving 0·2% permanent strain. For steels of various types, regardless of chemical composition and heat treatment, there was a relation between S / Y and the static strength Y , the ratio decreasing from approximately 3 when Y was 20 tons/sq. in. to 1 when Y was 120 tons/sq. in. A similar relation occurred with duralumin, S / Y varying from 2·5 at Y = 8 tons/sq. in. to 1·4 at Y = 25 tons/sq. in. Dynamic compressive yield values were obtained for soft materials such as pure lead, copper and Armco iron, which, under static conditions, gave no definite yield values. A plot of the unstrained length of the specimen X , expressed as X / L (where L = initial overall length), versus the final overall length L 1 , expressed as L 1 / L , was made for the various materials. Any specified value of X / L was associated with greater values of L 1 / L for the more ductile materials, such as copper and lead, than for the brittle materials, such as armour plate and duralumin.

scholarly journals Regional Coordination and Security of Water–Energy–Food Symbiosis in Northeastern China

2021 ◽  
Vol 13 (3) ◽  
pp. 1326
Author(s):  
Hongfang Li ◽  
Huixiao Wang ◽  
Yaxue Yang ◽  
Ruxin Zhao
Keyword(s):  
External Environment ◽  
Northeastern China ◽  
Decision Makers ◽  
Human Survival ◽  
A Value ◽  
Natural Factors ◽  
Regional Coordination ◽  
Micro Level ◽  
The Stability ◽  
Coordination Degree

The interactions of water, energy, and food, which are essential resources for human survival, livelihoods, production, and development, constitute a water–energy–food (WEF) nexus. Applying symbiosis theory, the economic, social, and natural factors were considered at the same time in the WEF system, and we conducted a micro-level investigation focusing on the stability, coordination, and sustainability of the symbiotic units (water, energy, and food), and external environment of the WEF system in 36 prefecture-level cities across three northeastern provinces of China. Finally, we analyzed the synergistic safety and coupling coordination degree of the WEF system by the combination of stability, coordination, and sustainability, attending to the coordination relationship and influences of the external environment. The results indicated that the synergistic safety of the WEF system in three northeastern provinces need to equally pay attention to the stability, coordination, and sustainability of the WEF system, since their weights were 0.32, 0.36 and 0.32, respectively. During 2010–2016, the synergistic safety indexes of the WEF system ranged between 0.40 and 0.60, which was a state of boundary safety. In the current study, the coupling coordination degree of the WEF system fluctuated around a value of 0.6, maintaining a primary coordination level; while in the future of 2021–2026, it will decline to 0.57–0.60, dropping to a weak coordinated level. The conclusion could provide effective information for decision-makers to take suitable measures for the security development of a WEF system.

scholarly journals Thermally Stimulated Desorption Optical Fiber-Based Interrogation System: An Analysis of Graphene Oxide Layers’ Stability

Photonics ◽  
2021 ◽  
Vol 8 (3) ◽  
pp. 70
Author(s):  
Maria Raposo ◽  
Carlota Xavier ◽  
Catarina Monteiro ◽  
Susana Silva ◽  
Orlando Frazão ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Optical Fiber ◽  
Optical Fiber Sensor ◽  
Layer By Layer ◽  
Film Stability ◽  
A Value ◽  
Device Reliability ◽  
Sensor Devices ◽  
Lbl Films ◽  
The Stability

Thin graphene oxide (GO) film layers are being widely used as sensing layers in different types of electrical and optical sensor devices. GO layers are particularly popular because of their tuned interface reflectivity. The stability of GO layers is fundamental for sensor device reliability, particularly in complex aqueous environments such as wastewater. In this work, the stability of GO layers in layer-by-layer (LbL) films of polyethyleneimine (PEI) and GO was investigated. The results led to the following conclusions: PEI/GO films grow linearly with the number of bilayers as long as the adsorption time is kept constant; the adsorption kinetics of a GO layer follow the behavior of the adsorption of polyelectrolytes; and the interaction associated with the growth of these films is of the ionic type since the desorption activation energy has a value of 119 ± 17 kJ/mol. Therefore, it is possible to conclude that PEI/GO films are suitable for application in optical fiber sensor devices; most importantly, an optical fiber-based interrogation setup can easily be adapted to investigate in situ desorption via a thermally stimulated process. In addition, it is possible to draw inferences about film stability in solution in a fast, reliable way when compared with the traditional ones.

Mathematical Model Establishment and Analysis on the Pipe Deformation under External Pressure with the Ovality

2013 ◽  
Vol 760-762 ◽  
pp. 2263-2266
Author(s):  
Kang Yong ◽  
Wei Chen
Keyword(s):  
Mathematical Model ◽  
Theoretical Analysis ◽  
Yield Strength ◽  
Residual Stresses ◽  
Numerical Simulations ◽  
Significant Influence ◽  
External Pressure ◽  
Pipe Diameter ◽  
Axial Loads ◽  
The Stability

Beside the residual stresses and axial loads, other factors of pipe like ovality, moment could also bring a significant influence on pipe deformation under external pressure. The Standard of API-5C3 has discussed the influences of deformation caused by yield strength of pipe, pipe diameter and pipe thickness, but the factor of ovality degree is not included. Experiments and numerical simulations show that with the increasing of pipe ovality degree, the anti-deformation capability under external pressure will become lower, and ovality affecting the stability of pipe shape under external pressure is significant. So it could be a path to find out the mechanics relationship between ovality and pipe deformation under external pressure by the methods of numerical simulations and theoretical analysis.

scholarly journals Study on the Stability of the Electrical Connection of High-Temperature Pressure Sensor Based on the Piezoresistive Effect of P-Type SiC

Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 216
Author(s):  
Yongwei Li ◽  
Ting Liang ◽  
Cheng Lei ◽  
Qiang Li ◽  
Zhiqiang Li ◽  
...  
Keyword(s):  
High Temperature ◽  
Pressure Sensor ◽  
Pressure Sensors ◽  
Extreme Environment ◽  
Maximum Temperature ◽  
Piezoresistive Effect ◽  
Electrical Connection ◽  
Contact Stability ◽  
The Stability ◽  
P Type

In this study, a preparation method for the high-temperature pressure sensor based on the piezoresistive effect of p-type SiC is presented. The varistor with a positive trapezoidal shape was designed and etched innovatively to improve the contact stability between the metal and SiC varistor. Additionally, the excellent ohmic contact was formed by annealing at 950 °C between Ni/Al/Ni/Au and p-type SiC with a doping concentration of 1018cm−3. The aging sensor was tested for varistors in the air of 25 °C–600 °C. The resistance value of the varistors initially decreased and then increased with the increase of temperature and reached the minimum at ~450 °C. It could be calculated that the varistors at ~100 °C exhibited the maximum temperature coefficient of resistance (TCR) of ~−0.35%/°C. The above results indicated that the sensor had a stable electrical connection in the air environment of ≤600 °C. Finally, the encapsulated sensor was subjected to pressure/depressure tests at room temperature. The test results revealed that the sensor output sensitivity was approximately 1.09 mV/V/bar, which is better than other SiC pressure sensors. This study has a great significance for the test of mechanical parameters under the extreme environment of 600 °C.

The stability of onoratoite, Sb8O11Cl2, in the supergene environment

2014 ◽  
Vol 78 (7) ◽  
pp. 1671-1675 ◽  
Author(s):  
Adam J. Roper ◽  
Peter Leverett ◽  
Timothy D. Murphy ◽  
Peter A. Williams
Keyword(s):  
Significant Influence ◽  
Secondary Phase ◽  
Low Ph ◽  
Stable Phase ◽  
Supergene Zone ◽  
A Value ◽  
Solubility Studies ◽  
The Stability ◽  
Very High

AbstractSynthesis and solubility studies of onoratoite have been undertaken to determine the role of this rare secondary phase in the immobilization of Sb and the conditions responsible for its formation in the supergene zone. Solubility studies were undertaken at 298.15 K. A value of ΔGfθ (Sb8O11Cl2, s, 298.15 K) = –2576 ±12 kJ mol–1 was derived. Calculations involving sénarmontite, Sb2O3, klebelsbergite, Sb4O4SO4(OH)2 and schafarzikite, FeSb2O4, show that onoratoite is a thermodynamically stable phase only at negligible activities of SO42–(aq) and low activities of Fe2+(aq), at low pH and very high activities of Cl–(aq). This explains why onoratoite is such a rare secondary phase and why it cannot exert any significant influence on the dispersion of Sb in the supergene environment.

The Stability of an Axially–Loaded Continuous Beam

1955 ◽  
Vol 59 (535) ◽  
pp. 506-509
Author(s):  
A. M. Dobson
Keyword(s):  
Axial Load ◽  
Classical Method ◽  
Complete Solution ◽  
Critical Value ◽  
Continuous Beam ◽  
Independent Variables ◽  
A Value ◽  
Method Of Solution ◽  
Axially Loaded ◽  
The Stability

The Classical method of solution of the stability of an axially–loaded continuous beam is by means of the three moments equation, using the Berry Functions, which are functions of the axial load. As the axial load approaches a value equal to the critical value for a pin–jointed beam, the Berry Functions tend to infinity, and the use of the three moments equations —(i. e. treating the end fixing moments as the independent variables)—leads to certain difficulties in the complete solution of the problem.The major difficulty lies in the question of stability. The critical value is determined by the vanishing of the determinant of the coefficients of the fixing moments in the three moments equations. This value could be found by plotting the determinant against end load (c. f. Pippard and Pritchard). However, in a problem involving a large number of bays, the calculation necessary to do this is likely to be considerable, for there may be many branches to the curve.

scholarly journals Vulnérabilité Future Des Systèmes De Productions Agricoles Face Aux Changements Climatiques Dans Le 4ème PDA : Cas Des Communes De Djidja Et De Djougou

2021 ◽  
Vol 25 (1) ◽  
pp. 445
Author(s):  
AWO Sourou Malikiyou ◽  
ALE Agbachi Georges ◽  
YABI Ibouraïma
Keyword(s):  
Climate Change ◽  
Minimum Temperature ◽  
Agricultural Production ◽  
Production Systems ◽  
Methodological Approach ◽  
Maximum Temperature ◽  
A Value ◽  
Current Minimum ◽  
Maximum Temperatures ◽  
Changements Climatiques

La variabilité climatique dans les communes de Djidja et de Djougou engendre des conséquences aussi bien sur les niveaux de productivités, de production que sur les revenus des exploitants agricoles. L’objectif de cette recherche est d’étudier la vulnérabilité future des systèmes de productions agricoles face aux changements climatiques dans les Communes de Djidja et de Djougou.L’approche méthodologique utilisée comprend la collecte des données, leur traitement et l’analyse des résultats. Les enquêtes ont été faites dans les villages choisis sur la base de critères bien définis (la taille de la population agricole et son implication dans la production agricole). La méthode de D. Schwartz (1995, p. 94) a permis de constituer l’échantillon de 377 producteurs. Enfin, une projection climatique sur la période 2019-2050/2075 est faite au moyen du logiciel climatique « Climate explorer ».Il ressort des résultats de l’étude que, dans la commune de Djougou, la variation au niveau de la température minimale actuelle (RCP8.5) est comprise entre -1,62°C en 1992 et 2,29°C en 2075. La température maximale quant à elle varie entre -1,40°C en 1994 à 2,18°C en 2075. C’est à partir de 2071 que l’augmentation de la température minimale va dépasser les 2°C et si rien n’est fait cette hausse va s’accroître et devenir permanente. De même, dans la commune de Djidja, la température minimale la plus élevée est observée en 2075 avec des variations de 1 à 2°C pour les RCP4.5 et RCP8.5. Au niveau de la température maximale, l’année la moins chaude est 1992 (-1,33mm/jour) pour RCP8.5 et 1991 (-1,02mm/jour) pour RCP4.5. La même évolution s’observe au niveau des températures maximales. L’année 1992 reste la plus déficitaire avec une chute de -1,60°C et l’année la plus excédentaire sera l’année 2075 avec une hausse de 2,18 mm par jour, sur la période 1992-2080. La corrélation est observée en 2042 avec une valeur de 0,322 mm par jour. L’examen des résultats révèle que les valeurs des paramètres climatiques à savoir précipitations et évaporation sont à la hausse sur la période 1980-2080 dans la commune de Djidja. Suivant la trajectoire actuelle, RCP8.5, les années les plus arrosées sont 2037, 2070 et 2073 avec respectivement des variations égales à 0,17mm et 0,27mm de pluie par jour. Face à ces difficultés, les populations agricoles adoptent des mesures pour contrer les contraintes climatiques.ABSTRACTClimatic variability in the communes of Djidja and Djougou has consequences both on the levels of productivity and production and on the income of farmers. The objective of this research is to study the vulnerability of agricultural production systems to climate change in the Communes of Djidja and Djougou.The methodological approach used includes data collection, processing and analysis of the results. The surveys were carried out in the villages chosen on the basis of well-defined criteria (the size of the agricultural population and its involvement in agricultural production). The method of D. Schwartz (1995, p. 94) made it possible to constitute the sample of 377 producers. Finally, a climate projection over the period 2019-2050 / 2075 is made using the climate software "Climate explorer".The results of the study show that, in the municipality of Djougou, the variation in the current minimum temperature (RCP8.5) is between -1.62 ° C in 1992 and 2.29 ° C in 2075. The maximum temperature varies between -1.40 ° C in 1994 to 2.18 ° C in 2075. It is from 2071 that the increase in the minimum temperature will exceed 2 ° C and if nothing is In fact, this increase will increase and become permanent. Similarly, in the municipality of Djidja, the highest minimum temperature is observed in 2075 withvariations of 1 to 2 ° C for RCP4.5 and RCP8.5. At maximum temperature, the coolest year is 1992 (-1.33mm / day) for RCP8.5 and 1991 (-1.02mm / day) for RCP4.5. The same development can be observed at the level of maximum temperatures. The year 1992 remains the most in deficit with a fall of -1.60 ° C and the year the most in surplus will be the year 2075 with an increase of 2.18mm per day, over the period 1992-2080. The correlation is observed in 2042 with a value of 0.322 mm per day. Examination of the results reveals that the values of climatic parameters, namely precipitation and evaporation, are on the rise over the period 1980-2080 in the municipality of Djidja. Following the current trajectory, RCP8.5, the wettest years are 2037, 2070 and 2073 with respectively variations equal to 0.17mm and 0.27mm of rain per day. Faced with these difficulties, agricultural populations are adopting measures to counter climatic constraints. Keywords: Djidja, Djougou, vulnerability, production system, agriculture, climate change.

Sign in / Sign up

Export Citation Format

Share Document