A study on design and properties of woven-nonwoven multi-layered hybrid geotextiles

2020 ◽  
pp. 152808372096470
Author(s):  
Ting-Ting Li ◽  
Xiangyu Zhou ◽  
Zhike Wang ◽  
Yuyang Fan ◽  
Xiayun Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Soil Conservation ◽  
Areal Density ◽  
Nonwoven Fabric ◽  
Test Results ◽  
Natural Conditions ◽  
Puncture Resistance ◽  
Stabilized Soil ◽  
Complicated Conditions ◽  
Pore Fraction

The area of forests continues decreasing while the water/soil loss becomes worse. In these complicated environments, mechanical properties, stability, high modulus and low elongation of geotextiles are required. On a premise of the acquisition of good mechanical properties and the improvement in the deformation and puncture resistance of nonwoven fabric, woven/nonwoven hybrid geotextiles are designed and made with needle punch processing technology in this study. The test results indicate that the mechanical properties of hybrid geotextiles are improved significantly when the areal density of nylon fabrics is increased. In particular, with the areal density of 400 g/m2, hybrid geotextiles exhibit the maximal mechanical properties and puncture resistance. Moreover, the pore fraction of hybrid geotextiles decreases as a result of a rise in the areal density of nylon top/bottom layers. The use of a 3 D mesh fabric as the interlayer provides the needle punched composite geotextiles with the highest tensile resistance, puncture resistance. The composite geotextiles are treated with acid and alkali to simulate the corrosion under natural conditions of stabilized soil. The resultant geotextile has good mechanical properties and acid/alkali degradation resistance. This allows the hybrid geotextiles to stabilize water and soil conservation in complicated conditions.

scholarly journals Research on the Dynamic Mechanical Properties and Energy Dissipation of Expansive Soil Stabilized by Fly Ash and Lime

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Sheng-quan Zhou ◽  
Da-wei Zhou ◽  
Yong-fei Zhang ◽  
Wei-jian Wang ◽  
Dongwei Li
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Expansive Soil ◽  
Dynamic Mechanical Properties ◽  
Test Results ◽  
Absorbed Energy ◽  
Dynamic Mechanical ◽  
Stabilized Soil ◽  
Dynamic Compressive Strength

To probe into the dynamic mechanical properties of expansive soil stabilized by fly ash and lime under impact load, the split-Hopkinson pressure bar (SHPB) test was carried out in this study. An analysis was made on the dynamic mechanical property and final fracture morphology of stabilized soil, and the failure mechanism was also explored from the perspective of energy dissipation. According to the test results, under the impact pressure of 0.2 MPa, plain soil and pure fly ash-stabilized soil exhibit strong plasticity. After the addition of lime, the stabilized soil shows obvious brittle failure. The dynamic compressive strength and absorbed energy of stabilized soil first increase and then decrease with the change of mix proportions. Both the dynamic compressive strength and the absorbed energy reach the peak value at the content of 20% fly ash and 5% lime (20% F + 5% L). In the process of the test, most of the incident energy is reflected back to the incident bar. The absorbed energy of stabilized soil increases linearly with the rise of dynamic compressive strength, while the absorbed energy is negatively correlated with the fractal dimension. The fractal dimension of pore morphology of the plain soil is lower than that of the fly ash-lime combined stabilized soil when it comes to the two different magnification ratios. The test results indicate that the modifier content of 20% F + 5% L can significantly improve the dynamic mechanical properties of the expansive soil.

Sunlight exposure: the effects on the performance of paragliding fabric

2018 ◽  
Vol 69 (05) ◽  
pp. 381-389
Author(s):  
MENGÜÇ GAMZE SÜPÜREN ◽  
TEMEL EMRAH ◽  
BOZDOĞAN FARUK
Keyword(s):  
Mechanical Properties ◽  
Aging Process ◽  
Air Permeability ◽  
Sunlight Exposure ◽  
Test Results ◽  
Coating Materials ◽  
Strength Tests ◽  
Before And After ◽  
The Relationship ◽  
Dark Blue

This study was designed to explore the relationship between sunlight exposure and the mechanical properties of paragliding fabrics which have different colors, densities, yarn counts, and coating materials. This study exposed 5 different colors of paragliding fabrics (red, turquoise, dark blue, orange, and white) to intense sunlight for 150 hours during the summer from 9:00 a.m. to 3:00 p.m. for 5 days a week for 5 weeks. Before and after the UV radiation aging process, the air permeability, tensile strength, tear strength, and bursting strength tests were performed. Test results were also evaluated using statistical methods. According to the results, the fading of the turquoise fabric was found to be the highest among the studied fabrics. It was determined that there is a significant decrease in the mechanical properties of the fabrics after sunlight exposure. After aging, the fabrics become considerably weaker in the case of mechanical properties due to the degradation in both the dyestuff and macromolecular structure of the fiber

Finite Element Analysis of Reinforced Concrete Beams with Exterior FRP Shell

2011 ◽  
Vol 243-249 ◽  
pp. 1461-1465
Author(s):  
Chuan Min Zhang ◽  
Chao He Chen ◽  
Ye Fan Chen
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Contact Interface ◽  
Accurate Calculation ◽  
Element Analysis

The paper makes an analysis of the reinforced concrete beams with exterior FRP Shell in Finite Element, and compares it with the test results. The results show that, by means of this model, mechanical properties of reinforced concrete beams with exterior FRP shell can be predicted better. However, the larger the load, the larger deviation between calculated values and test values. Hence, if more accurate calculation is required, issues of contact interface between the reinforced concrete beams and the FRP shell should be taken into consideration.

Improving the Strength of Abrasive Wheels and Optimizing the Control over the Strength of Composite Abrasive Materials

2019 ◽  
Vol 946 ◽  
pp. 380-385
Author(s):  
Boris A. Chaplygin ◽  
Viacheslav V. Shirokov ◽  
Tat'yana A. Lisovskaya ◽  
Roman A. Lisovskiy
Keyword(s):  
Mechanical Properties ◽  
Test Results ◽  
Key Factors ◽  
Special Equipment ◽  
Material Density ◽  
Factors Affecting ◽  
Control Factors ◽  
Reinforcing Material ◽  
Special Studies ◽  
First Time

The strength of abrasive wheels is one of the key factors affecting the performance of abrasive machining. The paper discusses ways to improve the strength of abrasive wheels. The stress-state mathematical model presented herein is a generalization of the existing models. It is used herein to find for the first time that there are numerous optimal combinations of the elastic modulus and reinforcing material density, which result in the same minimum value of the objective function. It is found out that increasing the radius of the reinforcing component while also optimizing the mechanical properties of its material may increase the permissible breaking speed of the wheel several times. We herein present a regression equation and a nomogram for finding the optimal combination of control factors. Conventional methods for testing the mechanical properties of materials, which have been proven reliable for testing metals and alloys, are not as reliable for testing abrasive materials, as the test results they generate are not sufficiently stable or accurate. We therefore propose an alternative method that does not require any special equipment or special studies.

Durability of Red Mud Based Geopolymer Paste in Acid Solutions

2016 ◽  
Vol 866 ◽  
pp. 99-105 ◽  
Author(s):  
Smita Singh ◽  
M.U. Aswath ◽  
R.V. Ranganath
Keyword(s):  
Mechanical Properties ◽  
Acetic Acid ◽  
Fly Ash ◽  
Red Mud ◽  
Acetic Acid Solution ◽  
Strength Loss ◽  
Acid Solutions ◽  
Test Results ◽  
Acid Attack ◽  
Geopolymer Paste

The present investigation is on the effect of red mud on the mechanical properties and durability of the geopolymer paste in sulphuric and acetic acid solution. Red mud and fly ash were used to form the geopolymer paste along with the alkalies. The variation of red mud in the paste composition was from 0% to 90%. Cylindrical shaped specimens of 1 inch diameter and 1 inch height were prepared. The specimens were immersed in 5% sulphuric acid and 5% acetic acid for 1, 7, 14, 28, 56 and 84 days and tested for weight loss, visual deformation, strength loss and colour of the solvent, based on the procedure specified by ASTM C 267 – 01. SEM/EDX Tests were performed on the geopolymer specimens. Test results show that initially, the strength of the geopolymer increased upon the addition of red mud. The strength was maximum when the percentage of red mud was 30%. The maximum strength obtained was 38 MPa for the paste containing 30% red mud using 10M alkali solution as against 31.69 MPa, when only fly ash was used. Geopolymer paste containing 30% and 50% red mud showed better resistance to acid attack. The strength loss was minimum for the samples containing 30% red mud in both inorganic and organic acid i.e. sulphuric and acetic acid.

Mechanical Behavior of Ti-6Al-4V Manufactured by Electron Beam Additive Fabrication

2013 ◽  
Author(s):  
Leila Ladani ◽  
Lalit Roy
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
Lead Time ◽  
Aerospace Industry ◽  
Tensile Tests ◽  
Test Results ◽  
Great Resistance ◽  
Additive Fabrication ◽  
Anisotropy Effect ◽  
The Cost

Additive Layer Fabrication, in particular Electron Beam Additive Fabrication (EBAF), has recently drawn much attention for its special usability to fabricate intricately designed parts as a whole. It not only increases the production rate which reduces the production lead time but also reduces the cost by minimizing the amount of waste material to a great extent. Ti6Al4V is the most common type of material that is currently being fabricated using EBAF technique. This material has been used in aerospace industry for several reasons such as excellent mechanical properties, low density, great resistance to corrosion, and non-magnetism. The effects of build direction of layers (namely, addition of layers along one of the x, y & z directions with respect to the build table) and the anisotropy effect caused by it has not been explored vigorously. This anisotropy effect has been investigated in this work. Different mechanical properties such as Yield Strength (YS), Ultimate Tensile Strength (UTS), and Modulus of Elasticity (E) of these three types of Ti6Al4V are determined using tensile tests and are compared with literature. The tensile test results show that YS and UTS for flat-build samples have distinguishably higher values than those of the side-build and top-build samples.

Study on the Basic Mechanical Properties of Recycled Concrete Hollow Block Masonry

2013 ◽  
Vol 438-439 ◽  
pp. 749-755 ◽  
Author(s):  
Tong Hao ◽  
Dong Li
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Shear Behavior ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Test Results ◽  
Aggregate Concrete ◽  
Mortar Strength ◽  
Hollow Block

By the experimental studying on the basic mechanical properties of recycled concrete hollow block masonry, the compressive and shear behavior of recycled aggregate concrete hollow block masonry under different mortar strength were analyzed. Research indicated that the compressive and shear behavior of recycled aggregate concrete hollow block masonry was similar to that of ordinary concrete hollow block masonry. The normal formula was recommended to calculate the compressive strength of the masonry. The shear strength of the masonry was affected by the mortar strength. The shear strength calculation formula of recycled concrete hollow block masonry was proposed according to the formula of masonry design code. The calculating results were in good agreement with the test results.

scholarly journals Dynamic Response of Thermally Bonded Bicomponent Fibre Nonwovens

2011 ◽  
Vol 70 ◽  
pp. 405-409 ◽  
Author(s):  
Emrah Demirci ◽  
Memiş Acar ◽  
Behnam Pourdeyhimi ◽  
Vadim V. Silberschmidt
Keyword(s):  
Mechanical Properties ◽  
Dynamic Response ◽  
Fibre Diameter ◽  
Orientation Distribution ◽  
Nonwoven Fabric ◽  
Woven Fabrics ◽  
Core Material ◽  
Finite Element Software ◽  
Anisotropic Mechanical Properties ◽  
Fibre Matrix

Having a unique microstructure, nonwoven fabrics possess distinct mechanical properties, dissimilar to those of woven fabrics and composites. This paper aims to introduce a methodology for simulating a dynamic response of core/sheath-type thermally bonded bicomponent fibre nonwovens. The simulated nonwoven fabric is treated as an assembly of two regions with distinct mechanical properties. One region - the fibre matrix – is composed of non-uniformly oriented core/sheath fibres acting as link between bond points. Non-uniform orientation of individual fibres is introduced into the model in terms of the orientation distribution function in order to calculate the structure’s anisotropy. Another region – bond points – is treated in simulations as a deformable bicomponent composite material, composed of the sheath material as its matrix and the core material as reinforcing fibres with random orientations. Time-dependent anisotropic mechanical properties of these regions are assessed based on fibre characteristics and manufacturing parameters such as the planar density, core/sheath ratio, fibre diameter etc. Having distinct anisotropic mechanical properties for two regions, dynamic response of the fabric is modelled in the finite element software with shell elements with thicknesses identical to those of the bond points and fibre matrix.

Preparation Techniques and Property Evaluations of Highly Air Permeable Needle-Punched Geotextiles

2015 ◽  
Vol 749 ◽  
pp. 278-281
Author(s):  
Jia Horng Lin ◽  
Jing Chzi Hsieh ◽  
Jin Mao Chen ◽  
Wen Hao Hsing ◽  
Hsueh Jen Tan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Service Life ◽  
Mechanical Strength ◽  
Pore Structure ◽  
Test Results ◽  
Needle Punching ◽  
Pet Fibers ◽  
Environmental Requirements ◽  
Preparation Techniques

Geotextiles are made of polymers, and their conjunction with different processes and materials can provide geotextiles with desirable characteristics and functions, such as filtration, separation, and drainage, and thereby meets the environmental requirements. Chemical resistant and mechanical strong polymers, including polyester (PET) and polypropylene (PP), are thus used to prolong the service life of the products made by such materials. This study proposes highly air permeable geotextiles that are made with different thicknesses and various needle punching speeds, and the influences of these two variables over the pore structure and mechanical properties are then examined. PET fibers, PP fibers, and recycled Kevlar fibers are blended, followed by being needle punched with differing spaces and speeds to form geotextiles with various thicknesses and porosities. The textiles are then evaluated for their mechanical strength and porosity. The test results show that a thickness of 4.5 cm and 1.5 cm demonstrate an influence on the tensile strength of the geotextiles, which is ascribed to the webs that are incompletely needle punched. However, the excessive needle punching speed corresponding to a thickness of 0.2 cm results in a decrease in tensile strength, but there is also an increase in the porosity of the geotextiles.

Sign in / Sign up

Export Citation Format

Share Document