scholarly journals Determination of color-changing effects of bleaching chemicals on some heat-treated woods

2020 ◽  
Vol 66 (1) ◽  
Author(s):  
Memiş Akkuş ◽  
Mehmet Budakçı
Keyword(s):  
Heat Treatment ◽  
Scots Pine ◽  
Color Change ◽  
Quercus Petraea ◽  
Treatment Temperature ◽  
Natural Color ◽  
Heat Treated ◽  
Total Color Change ◽  
Time Periods

Abstract The aim of this study was to use bleaching chemicals to remove the discoloration occurring on the surface of wood after heat treatment in order to restore the natural color of the wood. For this purpose, samples prepared from Scots pine (Pinus sylvestris L.), sessile oak (Quercus petraea L.), Eastern beech (Fagus orientalis L.), and Uludağ fir (Abies bornmuelleriana Mattf.) were exposed to heat treatment at temperatures of 140 and 160 °C for time periods of 3, 5, and 7 h. Bleaching solutions S1 (NaOH + H2O2), S2 (NaSiO3 + H2O2), and S3 (H2C2O4) at a concentration of 18% were then applied to the surface of the materials and the color change was determined according to ASTM D 2244 standard. Depending on the heat treatment temperature and duration, an increase in total color change values was detected on the surfaces of the materials and the color of the samples became darker. The total color change values decreased after bleaching with the S2 solution in the heat-treated Scots pine and fir samples, with the S3 solution in the beech samples, and with the S1, S2, and S3 solutions in the oak samples. The findings showed that by using bleaching chemicals to lighten wood materials darkened after heat treatment, it is possible to obtain results close to the natural color values.

scholarly journals Determination of Phase Transitions in Gutta-Percha by Differential Thermal Analysis

1977 ◽  
Vol 56 (12) ◽  
pp. 1453-1462 ◽  
Author(s):  
Hillar M. Rootare ◽  
John M. Powers
Keyword(s):  
Heat Treatment ◽  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Treatment Temperature ◽  
High Melting ◽  
Gutta Percha ◽  
Thermal Analyzer ◽  
Heat Treated ◽  
High Melting Form

Pure gutta-percha was heat-treated in a differential thermal analyzer. The high melting form crystallized on cooling when gutta-percha was heated to 70 C or less. Above 74 C, crystallization into the low melting form predominated. Either polymorph can be selectively crystallized by control of the heat-treatment temperature before cooling.

scholarly journals Effects of vacuum heat treatment and wax impregnation on the color of Pterocarpus macrocarpus Kurz.

BioResources ◽  
2020 ◽  
Vol 16 (1) ◽  
pp. 954-963
Author(s):  
Lin Yang ◽  
Tianqi Han ◽  
Yunxia Liu ◽  
Qin Yin
Keyword(s):  
Heat Treatment ◽  
Atmospheric Pressure ◽  
Color Change ◽  
Vacuum Heat Treatment ◽  
Wood Color ◽  
Heat Treated ◽  
Total Color Change

Pterocarpus macrocarpus Kurz. wood was vacuum heat treated (VHT)　at 120, 150, and 180 °C, under a pressure of 13.3 kPa. Half of the VHT specimens at 120 and 150 °C were subjected to wax impregnation　(WI) for 48 h at 90 °C under an atmospheric pressure. The effect of VHT and WI on wood color were investigated. The results showed that the VHT at 120 and 150 °C resulted in minor changes in lightness (L*), green-red chromatic coordinate (a*), blue-yellow chromatic coordinate (b*), total color change (ΔE*), and chroma (C*). However, the effect of VHT on L*, a*, b*, and C* at 180 °C became more obvious over the duration. After WI, the L*, a*, b*, and C* of the VHT wood at moderate temperatures varied noticeably, showing similar behavior with the VHT wood at 180 °C as L*, b*, and C* decreased and ΔE increased. However, a* increased after WI compared to that of VHT at 180 °C. The wood color of P. macrocarpus Kurz. after WI became reddish and blue, and the color deviation decreased. The wood color was closer to the dark mahogany, which facilitates its further application in rosewood furniture and woodwork art.

scholarly journals Enhancing Graphene Retention and Electrical Conductivity of Plasma-Sprayed Alumina/Graphene Nanoplatelets Coating by Powder Heat Treatment

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 643
Author(s):  
Xiaoyu Wu ◽  
Shufeng Xie ◽  
Kangwei Xu ◽  
Lei Huang ◽  
Daling Wei ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Electrical Conductivity ◽  
Structural Integrity ◽  
Ceramic Coatings ◽  
Treatment Temperature ◽  
Graphene Nanoplatelets ◽  
Structural Defects ◽  
Temperature Plasma ◽  
Heat Treated ◽  
Plasma Sprayed

Burning loss of graphene in the high-temperature plasma-spraying process is a critical issue, significantly limiting the remarkable performance improvement in graphene reinforced ceramic coatings. Here, we reported an effective approach to enhance the graphene retention, and thus improve the performance of plasma-sprayed alumina/graphene nanoplatelets (Al2O3/GNPs) coatings by heat treatment of agglomerated Al2O3/GNPs powders. The effect of powder heat treatment on the microstructure, GNPs retention, and electrical conductivity of Al2O3/GNPs coatings were systematically investigated. The results indicated that, with the increase in the powder heat treatment temperature, the plasma-sprayed Al2O3/GNPs coatings exhibited decreased porosity and improved adhesive strength. Thermogravimetric analysis and Raman spectra results indicated that increased GNPs retention from 12.9% to 28.4%, and further to 37.4%, as well as decreased structural defects, were obtained for the AG, AG850, and AG1280 coatings, respectively, which were fabricated by using AG powders without heat treatment, powders heat-treated at 850 °C, and powders heat-treated at 1280 °C. Moreover, the electrical conductivities of AG, AG850, and AG1280 coatings exhibited 3 orders, 4 orders, and 7 orders of magnitude higher than that of Al2O3 coating, respectively. Powder heat treatment is considered to increase the melting degree of agglomerated alumina particles, eventually leaving less thermal energy for GNPs to burn; thus, a high retention amount and structural integrity of GNPs and significantly enhanced electrical conductivity were achieved for the plasma-sprayed Al2O3/GNPs coatings.

scholarly journals Water Resistance and Creep Behavior of Heat-Treated Moso Bamboo Determined by the Stepped Isostress Method

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1264
Author(s):  
Teng-Chun Yang ◽  
Tung-Lin Wu ◽  
Chin-Hao Yeh
Keyword(s):  
Heat Treatment ◽  
Water Absorption ◽  
Creep Behavior ◽  
Heat Treatment Temperature ◽  
Water Resistance ◽  
Absorption Efficiency ◽  
Treatment Temperature ◽  
Moso Bamboo ◽  
Phyllostachys Pubescens ◽  
Heat Treated

The influence of heat treatment on the physico-mechanical properties, water resistance, and creep behavior of moso bamboo (Phyllostachys pubescens) was determined in this study. The results revealed that the density, moisture content, and flexural properties showed negative relationships with the heat treatment temperature, while an improvement in the dimensional stability (anti-swelling efficiency and anti-water absorption efficiency) of heat-treated samples was observed during water absorption tests. Additionally, the creep master curves of the untreated and heat-treated samples were successfully constructed using the stepped isostress method (SSM) at a series of elevated stresses. Furthermore, the SSM-predicted creep compliance curves fit well with the 90-day full-scale experimental data. When the heat treatment temperature increased to 180 °C, the degradation ratio of the creep resistance (rd) significantly increased over all periods. However, the rd of the tested bamboo decreased as the heat treatment temperature increased up to 220 °C.

Effect of Heat Treatment on the Microstructure and Property of TiAl Alloys Prepared by Gas Atomization Powders

2013 ◽  
Vol 747-748 ◽  
pp. 497-501
Author(s):  
Na Liu ◽  
Zhou Li ◽  
Guo Qing Zhang ◽  
Hua Yuan ◽  
Wen Yong Xu ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Tial Alloy ◽  
Lamellar Microstructure ◽  
Treatment Temperature ◽  
Gas Atomization ◽  
Thermally Induced ◽  
Heat Treated ◽  
Fine Duplex ◽  
Step Heat Treatment

Powder metallurgical TiAl alloy was fabricated by gas atomization powders, and the effect of heat treatment temperature on the microstructure evolution and room tensile properties of PM TiAl alloy was investigated. The uniform fine duplex microstructure was formed in PM TiAl based alloy after being heat treated at 1250/2h followed by furnace cooling (FC)+ 900/6h (FC). When the first step heat treatment temperature was improved to 1360/1h, the near lamellar microstructure was achieved. The ductility of the alloy after heat treatment improved markedly to 1.2% and 0.6%, but the tensile strength decreased to 570MPa and 600MPa compared to 655MPa of as-HIP TiAl alloy. Post heat treatment at the higher temperature in the alpha plus gamma field would regenerate thermally induced porosity (TIP).

Mechanical and Superelastic Properties of Au-51Ti-18Co Biomedical Shape Memory Alloy Heat-Treated at 1173 K to 1373 K

2016 ◽  
Vol 97 ◽  
pp. 141-146 ◽  
Author(s):  
Taywin Buasri ◽  
Hyunbo Shim ◽  
Masaki Tahara ◽  
Tomonari Inamura ◽  
Kenji Goto ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Critical Stress ◽  
Biomedical Applications ◽  
Shape Recovery ◽  
Treatment Temperature ◽  
Recovery Ratio ◽  
Recovery Strain ◽  
Heat Treated ◽  
Alloy Heat

The effect of heat treatment temperature from 1173 K to 1373 K for 3.6 ks on mechanical and superelastic properties of an Ni-free Au-51Ti-18Co alloy (mol%) was investigated. The stress for inducing martensitic transformation (SIMT) and the critical stress for slip deformation (CSS) slightly decrease with increasing the heat–treatment temperature. Regardless of heat–treatment temperature, good superelasticity was definitely recognized with the maximum shape recovery ratio up to 95 % and 4 % superelastic shape recovery strain. As the mentioned reasons, the Au-51Ti-18Co alloy is promising for practical biomedical applications.

Comparison of the color and weight change in Paulownia tomentosa and Pinus koraiensis wood heat-treated in hot oil and hot air

BioResources ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. 5574-5585
Author(s):  
Intan Fajar Suri ◽  
Jong Ho Kim ◽  
Byantara Darsan Purusatama ◽  
Go Un Yang ◽  
Denni Prasetia ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Color Change ◽  
Treated Wood ◽  
Pinus Koraiensis ◽  
Weight Changes ◽  
Paulownia Tomentosa ◽  
Wood Color ◽  
Color Changes ◽  
Hot Air ◽  
Heat Treated

Color changes were tested and compared for heat-treated Paulownia tomentosa and Pinus koraiensis wood treated with hot oil or hot air for further utilization of these species. Hot oil and hot air treatments were conducted at 180, 200, and 220 °C for 1, 2, and 3 h. Heat-treated wood color changes were determined using the CIE-Lab color system. Weight changes of the wood before and after heat treatment were also determined. The weight of the oil heat-treated wood increased considerably but it decreased in air heat-treated wood. The oil heat-treated samples showed a greater decrease in lightness (L*) than air heat-treated samples. A significant change in L* was observed in Paulownia tomentosa. The red/green chromaticity (a*) of both wood samples increased at 180 and 200 °C and slightly decreased at 220 °C. The yellow/blue chromaticity (b*) in both wood samples increased at 180 °C, but it rapidly decreased with increasing treatment durations at 200 and 220 °C. The overall color change (ΔE*) in both heat treatments increased with increasing temperature, being higher in Paulownia tomentosa than in Pinus koraiensis. In conclusion, oil heat treatment reduced treatment duration and was a more effective method than air heat treatment in improving wood color.

Investigation of Heat Treated Electrodeposited CoNiFe on Microstructure and Hardness

2015 ◽  
Vol 1113 ◽  
pp. 56-61
Author(s):  
Nor Azrina Resali ◽  
Koay Mei Hyie ◽  
M.N. Berhan ◽  
C.M. Mardziah
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Crystallographic Structure ◽  
Face Centered Cubic ◽  
Heat Treated ◽  
Hardness Property ◽  
Finishing Process ◽  
The Face ◽  
Face Centered

In this research, heat treatment is the final finishing process applied on nanocrystalline CoNiFe to improve microstructure for good hardness property. Nanocrystalline CoNiFe has been synthesized using the electrodeposition method. This study investigated the effect of heat treatment at 500°C, 600°C, 700°C and 800°C on electrodeposited nanocrystalline CoNiFe. The heat treatment process was performed in the tube furnace with flowing Argon gas. By changing the heat treatment temperature, physical properties such as phase and crystallographic structure, surface morphology, grain size and hardness of nanocrystalline CoNiFe was studied. The nanocrystalline CoNiFe phase revealed the Face Centered Cubic (FCC) and Body Centered Cubic (BCC) crystal structure. FESEM micrographs showed that the grain sizes of the coatings were in the range of 78.76 nm to 132 nm. Dendrite shape was found in the microstructure of nanocrystalline CoNiFe. The nanocrystalline CoNiFe prepared in heat treatment temperature of 700°C, achieved the highest hardness of 449 HVN. The surface roughness of nanocrystalline CoNiFe heated at 700°C was found to be smaller than other temperatures.

scholarly journals COLOR CHANGE — MASS LOSS CORRELATION FOR HEAT-TREATED WOOD

2014 ◽  
Vol 2 ◽  
pp. 345-352 ◽  
Author(s):  
Cristina Marinela Olarescu ◽  
Mihaela Campean
Keyword(s):  
Heat Treatment ◽  
Mass Loss ◽  
Color Change ◽  
Treated Wood ◽  
Untreated Wood ◽  
Cost Effective ◽  
Assessment Procedure ◽  
Mathematical Correlation ◽  
Heat Treated ◽  
Two Parameters

Heat treatment is renowned as the most environmentally friendly process of dimensional stabilization that can be applied to wood, in order to make it suitable for outdoor uses. It also darkens wood color and improves wood durability. The intensity of heat treatment can be appreciated by means of two parameters: the color change occured in wood due to the high temperature, and the mass loss, which is a measure of the degree of thermal degradation. In order to find a mathematical correlation between these two parameters, an experimental study was conducted with four European wood species, which were heat-treated at 180°C and 200ºC, for 1-3 hours, under atmosheric pressure.The paper presents the results concerning the color changes and mass losses recorded for the heat-treated wood samples compared to untreated wood.  For all four species, the dependency between the color change and the mass loss was found to be best described by a logarithmic regression equation with R2 of 0.93 to 0.99 for the soft species (spruce, pine and lime), and R2 of 0.77 for beech. The results of this study envisage to simplify the assessment procedure of the heat treatment efficiency, by only measuring the color – a feature that is both convenient and cost-effective. 

Effects of Heat-Treatment Temperature on the Properties of Negative CTE Eucryptite Ceramics

2010 ◽  
Vol 105-106 ◽  
pp. 123-125 ◽  
Author(s):  
Yong Li ◽  
Qi Hong Wei ◽  
Ling Li ◽  
Chong Hai Wang ◽  
Xiao Li Zhang ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Thermal Expansion ◽  
Thermal Expansion Coefficient ◽  
Expansion Coefficient ◽  
Heat Treatment Temperature ◽  
Bending Strength ◽  
Sol Gel ◽  
Negative Thermal Expansion ◽  
Treatment Temperature ◽  
Heat Treated

In this paper, negative thermal expansion coefficient eucryptite powders were prepared by sol-gel method using silica-sol as starting material. The raw blocks were obtained by dry pressing process after the powder was synthesized, and then the raw blocks were heat-treated at 600º, 1150º, 1280º, 1380º, 1420º and 1450°C, respectively. Variations of density, porosity and thermal expansion coefficient at different heat treatment temperatures were investigated. Phase transformation and fracture surface morphology of eucryptite heat-treated at different temperatures, respectively, were observed by XRD and SEM. The results indicate that, with the increasing heat- treatment temperature, the grain size and the bending strength increased, porosity decreased, thermal expansion coefficient decreased continuously. Negative thermal expansion coefficient of -5.3162×10-6~-7.4413×10-6 (0~800°C) was obtained. But when the heat-treatment temperature was more than 1420°C, porosity began to increase, bending strength began to decrease, which were the symbols of over-burning, while the main crystal phase didn’t change.

Sign in / Sign up

Export Citation Format

Share Document