Enhancing the Thermal and Mechanical Characteristics of Polyvinyl Alcohol (PVA)-Hemp Protein Particles (HPP) Composites

2021 ◽  
Vol 36 (2) ◽  
pp. 137-143
Author(s):  
S. A. Awad
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Composite Films ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Decomposition Temperature ◽  
Scanning Calorimetry ◽  
Solution Casting Method ◽  
Protein Particles

Abstract This paper aims to describe the thermal, mechanical, and surface properties of a PVA/HPP blend whereby the film was prepared using a solution casting method. The improvements in thermal and mechanical properties of HPP-based PVA composites were investigated. The characterization of pure PVA and PVA composite films included tensile tests, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results of TGA and DSC indicated that the addition of HPP increased the thermal decomposition temperature of the composites. Mechanical properties are significantly improved in PVA/HPP composites. The thermal stability of the PVA composite increased with the increase of HPP filler content. The tensile strength increased from 15.74 ± 0.72 MPa to 27.54 ± 0.45 MPa and the Young’s modulus increased from 282.51 ± 20.56 MPa to 988.69 ± 42.64 MPa for the 12 wt% HPP doped sample. Dynamic mechanical analysis (DMA) revealed that at elevated temperatures, enhanced mechanical properties because of the presence of HPP was even more noticeable. Morphological observations displayed no signs of agglomeration of HPP fillers even in composites with high HPP loading.

Preparation and characterization of polydimethylsiloxane-based composite films

2021 ◽  
Vol 63 (11) ◽  
pp. 984-987
Author(s):  
Enver Can Kılıç ◽  
Yavuz Salt
Keyword(s):  
Mechanical Properties ◽  
Composite Films ◽  
Thermal Characteristics ◽  
Tensile Tests ◽  
Composite Polymer ◽  
Scanning Calorimetry ◽  
Pdms Film ◽  
Ft Ir ◽  
Nay Zeolites

Abstract In this study, we aimed to find the characteristic properties of the neat and the composite polydimethylsiloxane (PDMS) films. The composite films were prepared by adding 5 A and NaY zeolites and nano-TiO2 to PDMS polymer matrix. In the preparation of the composite polymer films, the inorganic additives were added by 10 wt.-%. The structural and thermal characteristics of the prepared homogenous PDMS film and composite PDMS films were determined by Fourier transform infrared spectroscopy (FT-IR) and thermogravimetric analysis (TGA). The glass transition temperature of the films was found by differential scanning calorimetry (DSC). Finally, the mechanical properties of the films were obtained through tensile tests. The effects of 5 A and NaY zeolites and TiO2 on the neat PDMS films were investigated.

scholarly journals Mechanical, Thermal and Rheological Properties of Polyethylene-Based Composites Filled with Micrometric Aluminum Powder

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1242
Author(s):  
Olga Mysiukiewicz ◽  
Paulina Kosmela ◽  
Mateusz Barczewski ◽  
Aleksander Hejna
Keyword(s):  
Mechanical Properties ◽  
Melt Flow Index ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Metal Composites ◽  
Pre Treatment ◽  
The Impact ◽  
Properties Of Composites

Investigations related to polymer/metal composites are often limited to the analysis of the electrical and thermal conductivity of the materials. The presented study aims to analyze the impact of aluminum (Al) filler content (from 1 to 20 wt%) on the rarely investigated properties of composites based on the high-density polyethylene (HDPE) matrix. The crystalline structure, rheological (melt flow index and oscillatory rheometry), thermal (differential scanning calorimetry), as well as static (tensile tests, hardness, rebound resilience) and dynamic (dynamical mechanical analysis) mechanical properties of composites were investigated. The incorporation of 1 and 2 wt% of aluminum filler resulted in small enhancements of mechanical properties, while loadings of 5 and 10 wt% provided materials with a similar performance to neat HDPE. Such results were supported by the lack of disturbances in the rheological behavior of composites. The presented results indicate that a significant content of aluminum filler may be introduced into the HDPE matrix without additional pre-treatment and does not cause the deterioration of composites’ performance, which should be considered beneficial when engineering PE/metal composites.

The Structure and Mechanical Properties of Plastically Consolidated Al-Ni Alloy

2016 ◽  
Vol 682 ◽  
pp. 245-251 ◽  
Author(s):  
Grzegorz Włoch ◽  
Tomasz Skrzekut ◽  
Jakub Sobota ◽  
Antoni Woźnicki ◽  
Justyna Cisoń
Keyword(s):  
Mechanical Properties ◽  
Vickers Hardness ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Intermetallic Phases ◽  
Scanning Calorimetry ◽  
Porosity Formation ◽  
X Ray ◽  
Ni Alloy ◽  
Thermal Stability Of

Mixed and preliminarily consolidated powders of aluminium and nickel (90 mass % Al and 10 mass % Ni) were hot extruded. As results the rod, 8 mm in diameter, was obtained. As-extruded material was subjected to the microstructural investigations using scanning electron microscopy (SEM/EDS) and X-ray analysis (XRD). The differential scanning calorimetry (DSC) and thermo-mechanical analysis (TMA) were also performed. The mechanical properties of as extruded material were determined by the tensile test and Vickers hardness measurements. In order to evaluate the thermal stability of PM alloy, samples were annealed at the temperature of 475 and 550 °C. After annealing Vickers hardness measurements and tensile tests were carried out. The plastic consolidation of powders during extrusion was found to be very effective, because no pores or voids were observed in the examined material. The detailed microstructural investigations and XRD analyses did not reveal the presence of the intermetallic phases in the as-extruded material. During annealing, the Al3Ni intermetallic compound was formed as the result of chemical reaction between the alloy components. The hardness of the alloy after annealing at the temperature of 475°C was found to be comparable to the hardness in as-extruded state. Annealing of the material at the temperature of 550°C results in hardness decreasing by about 50%, as the consequence of porosity formation and Al3Ni cracking.

scholarly journals Influence of the Lignin Content on the Properties of Poly(Lactic Acid)/lignin-Containing Cellulose Nanofibrils Composite Films

Polymers ◽  
2018 ◽  
Vol 10 (9) ◽  
pp. 1013 ◽  
Author(s):  
Xuan Wang ◽  
Yuan Jia ◽  
Zhen Liu ◽  
Jiaojiao Miao
Keyword(s):  
Lactic Acid ◽  
Lignin Content ◽  
Cellulose Nanofibrils ◽  
Composite Films ◽  
Tensile Tests ◽  
Nucleating Agent ◽  
Mechanical Analysis ◽  
Degree Of Crystallinity ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry

Poly(lactic acid) (PLA)/lignin-containing cellulose nanofibrils (L-CNFs) composite films with different lignin contents were produced bythe solution casting method. The effect of the lignin content on the mechanical, thermal, and crystallinity properties, and PLA/LCNFs interfacial adhesion wereinvestigated by tensile tests, thermogravimetric analysis, differential scanning calorimetry (DSC), dynamic mechanical analysis, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). The tensile strength and modulus of the PLA/9-LCNFs (9 wt % lignin LCNFs) composites are 37% and 61% higher than those of pure PLA, respectively. The glass transition temperature (Tg) decreases from 61.2 for pure PLA to 52.6 °C for the PLA/14-LCNFs (14 wt % lignin LCNFs) composite, and the composites have higher thermal stability below 380 °C than pure PLA. The DSC results indicate that the LCNFs, containing different lignin contents, act as a nucleating agent to increase the degree of crystallinity of PLA. The effect of the LCNFs lignin content on the PLA/LCNFs compatibility/adhesion was confirmed by the FTIR, SEM, and Tg results. Increasing the LCNFs lignin content increases the storage modulus of the PLA/LCNFs composites to a maximum for the PLA/9-LCNFs composite. This study shows that the lignin content has a considerable effect on the strength and flexibility of PLA/LCNFs composites.

scholarly journals Study of Mechanical Properties of PHBHV/Miscanthus Green Composites Using Combined Experimental and Micromechanical Approaches

Polymers ◽  
2021 ◽  
Vol 13 (16) ◽  
pp. 2650
Author(s):  
Thibault Lemaire ◽  
Erica Gea Rodi ◽  
Valérie Langlois ◽  
Estelle Renard ◽  
Vittorio Sansalone
Keyword(s):  
Mechanical Properties ◽  
Tensile Modulus ◽  
Tensile Tests ◽  
Specific Class ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Green Wood ◽  
Miscanthus Giganteus ◽  
The One

In recent years the interest in the realization of green wood plastic composites (GWPC) materials has increased due to the necessity of reducing the proliferation of synthetic plastics. In this work, we study a specific class of GWPCs from its synthesis to the characterization of its mechanical properties. These properties are related to the underlying microstructure using both experimental and modeling approaches. Different contents of Miscanthus giganteus fibers, at 5, 10, 20, 30 weight percent’s, were thus combined to a microbial matrix, namely poly (3-hydroxybutyrate)-co-poly(3-hydroxyvalerate) (PHBHV). The samples were manufactured by extrusion and injection molding processing. The obtained samples were then characterized by cyclic-tensile tests, pycnometer testing, differential scanning calorimetry, Fourier transform infrared spectroscopy, X-ray diffraction, and microscopy. The possible effect of the fabrication process on the fibers size is also checked. In parallel, the measured properties of the biocomposite were also estimated using a Mori–Tanaka approach to derive the effective behavior of the composite. As expected, the addition of reinforcement to the polymer matrix results in composites with higher Young moduli on the one hand, and lower failure strains and tensile strengths on the other hand (tensile modulus was increased by 100% and tensile strength decreased by 23% when reinforced with 30 wt % of Miscanthus fibers).

scholarly journals Preparation of Multicomponent Biocomposites and Characterization of Their Physicochemical and Mechanical Properties

2020 ◽  
Vol 4 (1) ◽  
pp. 18
Author(s):  
Yuriy A. Anisimov ◽  
Duncan E. Cree ◽  
Lee D. Wilson
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Physicochemical Properties ◽  
In Situ Polymerization ◽  
Structural Parameters ◽  
Dye Adsorption ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Swelling Properties

This work focused on a mutual comparison and characterization of the physicochemical properties of three-component polymer composites. Binary polyaniline–chitosan (PANI–CHT) composites were synthesized by in situ polymerization of PANI onto CHT. Ternary composites were prepared by blending with a third component, polyvinyl alcohol (PVA). Composites with variable PANI:CHT (25:75, 50:50 and 75:25) weight ratios were prepared whilst fixing the composition of PVA. The structure and physicochemical properties of the composites were evaluated using thermal analysis (thermogravimetric analysis (TGA), differential scanning calorimetry (DSC)) and spectroscopic methods (infrared (IR), nuclear magnetic resonance (NMR)). The equilibrium and dynamic adsorption properties of composites were evaluated by solvent swelling in water, water vapour adsorption and dye adsorption isotherms. The electrical conductivity was estimated using current–voltage curves. The mechanical properties of the samples were evaluated using dynamic mechanical analysis (DMA) and correlated with the structural parameters of the composites. The adsorption and swelling properties paralleled the change in the electrical and mechanical properties of the materials. In most cases, samples with higher content of chitosan exhibit higher adsorption and mechanical properties, and lower conductivity. Acid-doped samples showed much higher adsorption, swelling, and electrical conductivity than their undoped analogues.

scholarly journals Biodegradable and Toughened Composite of Poly(Propylene Carbonate)/Thermoplastic Polyurethane (PPC/TPU): Effect of Hydrogen Bonding

2018 ◽  
Vol 19 (7) ◽  
pp. 2032 ◽  
Author(s):  
Dongmei Han ◽  
Guiji Chen ◽  
Min Xiao ◽  
Shuanjin Wang ◽  
Shou Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Propylene Carbonate ◽  
Thermoplastic Polyurethane ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Thermal Stabilities ◽  
Dynamic Mechanical ◽  
Brittle Ductile Transition ◽  
Poly Propylene

The blends of Poly(propylene carbonate) (PPC) and polyester-based thermoplastic polyurethane (TPU) were melt compounded in an internal mixer. The compatibility, thermal behaviors, mechanical properties and toughening mechanism of the blends were investigated using Fourier transform infrared spectra (FTIR), tensile tests, impact tests, differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and dynamic mechanical analysis technologies. FTIR and SEM examination reveal strong interfacial adhesion between PPC matrix and suspended TPU particles. Dynamic mechanical analyzer (DMA) characterize the glass transition temperature, secondary motion and low temperature properties. By the incorporation of TPU, the thermal stabilities are greatly enhanced and the mechanical properties are obviously improved for the PPC/TPU blends. Moreover, PPC/TPU blends exhibit a brittle-ductile transition with the addition of 20 wt % TPU. It is considered that the enhanced toughness results in the shear yielding occurred in both PPC matrix and TPU particles of the blends.

scholarly journals Microstructure and Mechanical Properties of Precipitate Strengthened High Entropy Alloy Al10Co25Cr8Fe15Ni36Ti6 with Additions of Hafnium and Molybdenum

Entropy ◽  
2019 ◽  
Vol 21 (2) ◽  
pp. 169 ◽  
Author(s):  
Sebastian Haas ◽  
Anna M. Manzoni ◽  
Fabian Krieg ◽  
Uwe Glatzel
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Base Alloy ◽  
Tensile Tests ◽  
High Entropy Alloy ◽  
High Entropy ◽  
Positive Effects ◽  
High Temperature Materials ◽  
Equiatomic Alloy

High entropy or compositionally complex alloys provide opportunities for optimization towards new high-temperature materials. Improvements in the equiatomic alloy Al17Co17Cr17Cu17Fe17Ni17 (at.%) led to the base alloy for this work with the chemical composition Al10Co25Cr8Fe15Ni36Ti6 (at.%). Characterization of the beneficial particle-strengthened microstructure by scanning electron microscopy (SEM) and observation of good mechanical properties at elevated temperatures arose the need of accomplishing further optimization steps. For this purpose, the refractory metals hafnium and molybdenum were added in small amounts (0.5 and 1.0 at.% respectively) because of their well-known positive effects on mechanical properties of Ni-based superalloys. By correlation of microstructural examinations using SEM with tensile tests in the temperature range of room temperature up to 900 °C, conclusions could be drawn for further optimization steps.

Processing and MWNT Composition Effects on the Thermal, Electrical and Mechanical Properties of PLA-MWNT Composites

2009 ◽  
Author(s):  
Reza R. Rizvi ◽  
Jae K. Kim ◽  
Hani E. Naguib
Keyword(s):  
Mechanical Properties ◽  
Thermo Gravimetric Analysis ◽  
Composite Films ◽  
Thermal Characteristics ◽  
Casting Process ◽  
Decomposition Temperature ◽  
Multiwall Carbon Nanotube ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Electrical Percolation

This paper investigates the processing and its effects and the effect of multiwall carbon nanotube (MWNT) composition on the thermal, electrical and mechanical properties of polylactide (PLA)-MWNT composites. The composite films were prepared by a solvent casting process using two solvents, chloroform and 1,4-dioxane. The dispersion of the MWNTs in PLA was examined using a scanning electron microscope and was found to be more improved when 1,4-dioxane was used as the solvent as compared to chloroform. The thermal characteristics of the composites were examined on Differential Scanning Calorimetry and Thermo-gravimetric Analysis. Composites prepared using 1,4-dioxane had greater improvements in composite decomposition temperature, glass transition temperature and displayed faster crystallization kinetics. The mechanical properties of the composites were tested in uniaxial tension. Composites prepared using chloroform had a lower modulus than composites prepared using 1,4-dioxane. The electrical AC conductivity of the composites was measured over a broad frequency spectrum. Composites prepared using 1,4-dioxane displayed electrical percolation at 0.5 wt.% MWNT in PLA while percolation was absent in 0.5 wt.% MWNT composites prepared using chloroform.

Mechanical Properties of Laser Cut Poly(L-Lactide) Micro-Specimens: Implications for Stent Design, Manufacture, and Sterilization

2005 ◽  
Vol 127 (1) ◽  
pp. 25-31 ◽  
Author(s):  
Niels Grabow ◽  
Martin Schlun ◽  
Katrin Sternberg ◽  
Nico Hakansson ◽  
Sven Kramer ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Material Selection ◽  
Polymeric Materials ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Machining Process ◽  
Scanning Calorimetry ◽  
Vascular Stents ◽  
Before And After ◽  
Solution Cast

Background: The development of endoluminal stents from polymeric materials requires an understanding of the basic mechanical properties of the polymer and the effects of manufacturing and sterilization on those properties. Methods: Pure poly(L-lactide) (PLLA) and PLLA containing varying amounts of triethylcitrate (TEC) as a plasticizer (5-10-15%) were studied. The specimens were solution-cast and CO2 laser-cut. Specimen dimensions were adapted to the strut size of polymeric vascular stents. The properties of the PLLA micro-specimens were assessed before and after sterilization (EtO cold gas, H2O2-plasma, beta- and gamma-irradiation). Tensile tests, and creep and recovery tests were carried out at 37°C. Additionally the thermal and thermo-mechanical characteristics were investigated using dynamic-mechanical analysis (DMA) and differential scanning calorimetry (DSC). Results: The results showed the dramatic influence of the plasticizer content and sterilization procedure on the mechanical properties of the material. Laser cutting had a lesser effect. Hence the effects of processing and sterilization must not be overlooked in the material selection and design phases of the development process leading to clinical use. Altogether, the results of these studies provide a clearer understanding of the complex interaction between the laser machining process and terminal sterilization on the primary mechanical properties of PLLA and PLLA plasticized with TEC.

Sign in / Sign up

Export Citation Format

Share Document