scholarly journals The impact of cold deformation, annealing temperatures and chemical assays on the mechanical properties of platinum

2010 ◽  
Vol 46 (1) ◽  
pp. 51-57 ◽  
Author(s):  
B. Trumic ◽  
D. Stankovic ◽  
A. Ivanovic
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Annealing Temperature ◽  
Cold Deformation ◽  
Platinum Metals ◽  
Deformation Degree ◽  
Annealing Temperatures ◽  
Flow Limit ◽  
The Impact ◽  
Constant Deformation

In order to form the necessary data base on platinum and platinum metals, certain tests were carried out on platinum samples of different purity of 99.5%, 99.9% and 99.99%. The degree of cold deformation, annealing temperature and chemical assays were tested as well as their impact on the mechanical properties of platinum. The Vickers hardness (HV) values were determined with different deformation degree, starting from annealing temperatures for platinum of different purity and tensile strength (Rm), flow limit (Rp0,2) and elongation (A) in the function of annealing temperatures and annealing time at a constant deformation degree.

Effect of Cold Deformation and Annealing on Microstructure and Mechanical Properties of 5083 Aluminum Alloy Sheets

2018 ◽  
Vol 913 ◽  
pp. 49-54
Author(s):  
Jian Xin Wu ◽  
Chong Gao ◽  
Rui Yin Huang ◽  
Zhen Shan Liu ◽  
Pi Zhi Zhao
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Annealing Temperature ◽  
Cold Deformation ◽  
Rolling Process ◽  
Prolonged Annealing ◽  
5083 Aluminum Alloy ◽  
Research Hotspots

5083 aluminum alloy, due to moderate strength, good thermal conductivity and formability, is an ideal structural material for car production. Influence of cold rolling process on microstructures and mechanical properties of 5083 aluminum alloys is significant and research hotspots. In this paper, cold deformation and annealing processes on grains, tensile properties and anisotropies of 5083 alloy sheets were studied. Results showed that incomplete recrystallization occured on 5083 alloy sheets when annealing temperature was at 300°C. The degree of recrystallization increased slightly with the cold deformation raised from 30% to 50% and varied slightly with prolonged annealing time from 2h to 4h. Furthermore, fully recrystallization occurred on 5083 alloy sheets at the annealing temperature above 320°C. Tensile strength of 5083 alloy sheets reduced significantly when the annealing temperature was raised from 300°C to 320°C, while it varied slightly when the annealing temperature continued to rise to 380°C.

Effect of Annealing Temperature on Mechanical Properties of Cold Drawn Pearlitic Steel Wires

2006 ◽  
Vol 118 ◽  
pp. 31-34 ◽  
Author(s):  
Won Jong Nam ◽  
Hyung Rak Song ◽  
Kyung Tae Park
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Annealing Time ◽  
Annealing Temperature ◽  
Annealing Treatment ◽  
Pearlitic Steel ◽  
High Annealing Temperature ◽  
Annealing Temperatures ◽  
Steel Wires ◽  
High Annealing

The effects of annealing temperature and annealing time on mechanical properties of cold drawn pearlitic steel wires containing 0.84wt% of silicon were investigated. Annealing treatment was performed on cold drawn steel wires for the temperature range of 200°C to 450°C with the different annealing time of 30sec, 1min, 15min and 1hr. The increase of tensile strength at the low annealing temperatures would be related with strain ageing behavior, while the decrease of tensile strength at the high annealing temperature is due to the spheroidization of cementite plates and the occurrence of recovery of the lamellar ferrite in the pearlite.

Effects of Deformation Strains and Annealing Temperatures on Mechanical Properties of Martensitic Steels

2010 ◽  
Vol 654-656 ◽  
pp. 218-221 ◽  
Author(s):  
Jong Chul Lee ◽  
Ui Gu Kang ◽  
Chang Suk Oh ◽  
Sung Joon Kim ◽  
Won Jong Nam
Keyword(s):  
Mechanical Properties ◽  
Annealing Temperature ◽  
Cold Deformation ◽  
High Strength ◽  
Total Elongation ◽  
Good Combination ◽  
Martensitic Steels ◽  
Annealing Temperatures ◽  
Cold Rolled ◽  
Carbide Particles

The effects of deformation strains and annealing temperatures on microstructures and mechanical properties of martensitic steels were examined. The amount of cold deformation was changed as 30%, 50% and 60%, and annealing temperatures varied from 500°C to 600°C. In samples cold rolled 30%, the dominant microstructure for an annealing at 500°C was dislocation substructures with uniformly distributed rod-shaped carbide particles. For an annealing at 600°C, the microstructure consisted of equiaxed ultrafine grains, spherical carbide particles and elongated dislocation substructures. A proper annealing temperature for martensitic steels received 30% reduction, showing a good combination of a high strength, 1230MPa, and an adequate total elongation. 9.4%, was found as 500°C.

scholarly journals Effects of recrystallization annealing on mechanical properties of cold-rolled PdNi5 wires

10.30544/136 ◽  
2016 ◽  
Vol 22 (1) ◽  
pp. 17-24
Author(s):  
Aleksandra Ivanović ◽  
Biserka Trumić ◽  
Svetlana Ivanov ◽  
Saša Marjanović ◽  
Silvana Dimitrijević ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Annealing Time ◽  
Annealing Temperature ◽  
Cold Deformation ◽  
Testing Machine ◽  
Recrystallization Temperature ◽  
Time Range ◽  
Recrystallization Annealing ◽  
Deformation Degree ◽  
Cold Rolled

The aim of this investigation was to determine the influence of the recrystallization temperature and recrystallization time on the microstructure and mechanical properties of the PdNi5 alloy subjected to cold deformation in the process of rolling at a constant deformation degree. The samples of PdNi5 alloy were recrystallization annealed within the temperature range of 200-1000ºC and annealing time range of 20-45 min after cold rolling with deformation degree of 97%. The tensile test was carried out using universal material testing machine. The hardness was also measured on the combined device for measuring Vickers and Brinell hardness. Metallographic observations were performed on an optical microscope. The analysis of the results of investigations regarding the microstructural changes and corresponding mechanical properties of cold-rolled PdNi5 strips shows that annealing temperature of 500ºC was sufficient to activate the energy for various recrystallization processes causing a change in the mechanical properties of cold-rolled PdNi5 strips. The annealing time, at constant annealing temperature, almost did not affect a recrystallization temperature and the mechanical properties of the cold-rolled PdNi5 strips.

Effect of combined drink cans and steel fibers on the impact resistance and mechanical properties of concrete

2020 ◽  
Vol 14 (2) ◽  
pp. 6734-6742
Author(s):  
A. Syamsir ◽  
S. M. Mubin ◽  
N. M. Nor ◽  
V. Anggraini ◽  
S. Nagappan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Indirect Tensile ◽  
The Impact

This study investigated the combine effect of 0.2 % drink cans and steel fibers with volume fractions of 0%, 0.5%, 1%, 1.5%, 2%, 2.5% and 3% to the mechanical properties and impact resistance of concrete. Hooked-end steel fiber with 30 mm and 0.75 mm length and diameter, respectively was selected for this study.  The drinks cans fiber were twisted manually in order to increase friction between fiber and concrete. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the strength performance of concrete, especially the compressive strength, flexural strength and indirect tensile strength. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the compressive strength, flexural strength and indirect tensile strength by 2.3, 7, and 2 times as compare to batch 1, respectively. Moreover, the impact resistance of fiber reinforced concrete has increase by 7 times as compared to non-fiber concretes. Moreover, the impact resistance of fiber reinforced concrete consistently gave better results as compared to non-fiber concretes. The fiber reinforced concrete turned more ductile as the dosage of fibers was increased and ductility started to decrease slightly after optimum fiber dosage was reached. It was found that concrete with combination of 2% steel and 0.2% drink cans fibers showed the highest compressive, split tensile, flexural as well as impact strength.    

scholarly journals Damage Evolution of Granodiorite after Heating and Cooling Treatments

Minerals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 779
Author(s):  
Mohamed Gomah ◽  
Guichen Li ◽  
Salah Bader ◽  
Mohamed Elkarmoty ◽  
Mohamed Ismael
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Failure Mode ◽  
Physical And Mechanical Properties ◽  
P Wave ◽  
Physical Parameters ◽  
Slow Cooling ◽  
Heating And Cooling ◽  
Natural Rock ◽  
The Impact

The awareness of the impact of high temperatures on rock properties is essential to the design of deep geotechnical applications. The purpose of this research is to assess the influence of heating and cooling treatments on the physical and mechanical properties of Egyptian granodiorite as a degrading factor. The samples were heated to various temperatures (200, 400, 600, and 800 °C) and then cooled at different rates, either slowly cooled in the oven and air or quickly cooled in water. The porosity, water absorption, P-wave velocity, tensile strength, failure mode, and associated microstructural alterations due to thermal effect have been studied. The study revealed that the granodiorite has a slight drop in tensile strength, up to 400 °C, for slow cooling routes and that most of the physical attributes are comparable to natural rock. Despite this, granodiorite thermal deterioration is substantially higher for quick cooling than for slow cooling. Between 400:600 °C is ‘the transitional stage’, where the physical and mechanical characteristics degraded exponentially for all cooling pathways. Independent of the cooling method, the granodiorite showed a ductile failure mode associated with reduced peak tensile strengths. Additionally, the microstructure altered from predominantly intergranular cracking to more trans-granular cracking at 600 °C. The integrity of the granodiorite structure was compromised at 800 °C, the physical parameters deteriorated, and the rock tensile strength was negligible. In this research, the temperatures of 400, 600, and 800 °C were remarked to be typical of three divergent phases of granodiorite mechanical and physical properties evolution. Furthermore, 400 °C could be considered as the threshold limit for Egyptian granodiorite physical and mechanical properties for typical thermal underground applications.

Residual Stresses in Intrinsic UD-CFRP-Steel-Laminates - Experimental Determination, Identification of Sources, Effects and Modification Approaches

2015 ◽  
Vol 825-826 ◽  
pp. 369-376 ◽  
Author(s):  
Robert Prussak ◽  
Daniel Stefaniak ◽  
Christian Hühne ◽  
Michael Sinapius
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Tensile Strength ◽  
Epoxy Composite ◽  
Thermal Residual Stress ◽  
Fiber Metal Laminates ◽  
Fiber Metal ◽  
Impact Energies ◽  
The Impact ◽  
Specific Impact

This paper focuses on the reduction of process-related thermal residual stress in fiber metal laminates and its impact on the mechanical properties. Different modifications during fabrication of co-cure bonded steel/carbon epoxy composite hybrid structures were investigated. Specific examinations are conducted on UD-CFRP-Steel specimens, modifying temperature, pressure or using a thermal expansion clamp during manufacturing. The impact of these parameters is then measured on the deflection of asymmetrical specimens or due yield-strength measurements of symmetrical specimens. The tensile strength is recorded to investigate the effect of thermal residual stress on the mechanical properties. Impact tests are performed to determine the influence on resulting damage areas at specific impact energies. The experiments revealed that the investigated modifications during processing of UD-CFRP-Steel specimens can significantly lower the thermal residual stress and thereby improve the tensile strength.

Optically Transparent Polymethyl Methacrylate Composites made with Glass Fibers of Varying Refractive Index

1997 ◽  
Vol 12 (4) ◽  
pp. 1091-1101 ◽  
Author(s):  
Seunggu Kang ◽  
Hongy Lin ◽  
Delbert E. Day ◽  
James O. Stoffer
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Refractive Index ◽  
Mechanical Strength ◽  
Glass Fiber ◽  
Polymethyl Methacrylate ◽  
Optical Transmission ◽  
Annealing Temperature ◽  
Glass Fibers ◽  
Optically Transparent

The dependence of the optical and mechanical properties of optically transparent polymethyl methacrylate (PMMA) composites on the annealing temperature of BK10 glass fibers was investigated. Annealing was used to modify the refractive index (R.I.) of the glass fiber so that it would more closely match that of PMMA. Annealing increased the refractive index of the fibers and narrowed the distribution of refractive index of the fibers, but lowered their mechanical strength so the mechanical properties of composites reinforced with annealed fibers were not as good as for composites containing as-pulled (chilled) glass fibers. The refractive index of as-pulled 17.1 μm diameter fibers (R.I. = 1.4907) increased to 1.4918 and 1.4948 after annealing at 350 °C to 500 °C for 1 h or 0.5 h, respectively. The refractive index of glass fibers annealed at 400 °C/1 h best matched that of PMMA at 589.3 nm and 25 °C, so the composite reinforced with those fibers had the highest optical transmission. Because annealed glass fibers had a more uniform refractive index than unannealed fibers, the composites made with annealed fibers had a higher optical transmission. The mechanical strength of annealed fiber/PMMA composites decreased as the fiber annealing temperature increased. A composite containing fibers annealed at 450 °C/1 h had a tensile strength 26% lower than that of a composite made with as-pulled fibers, but 73% higher than that for unreinforced PMMA. This decrease was avoided by treating annealed fibers with HF. Composites made with annealed and HF (10 vol. %)-treated (for 30 s) glass fibers had a tensile strength (∼200 MPa) equivalent to that of the composites made with as-pulled fibers. However, as the treatment time in HF increased, the tensile strength of the composites decreased because of a significant reduction in diameter of the glass fiber which reduced the volume percent fiber in the composite.

scholarly journals Numerical Studies of the Effects of Water Capsules on Self-Healing Efficiency and Mechanical Properties in Cementitious Materials

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Haoliang Huang ◽  
Guang Ye
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Cementitious Materials ◽  
Self Healing ◽  
Negative Effects ◽  
Numerical Studies ◽  
Healing Efficiency ◽  
The Impact ◽  
Positive Effect

In this research, self-healing due to further hydration of unhydrated cement particles is taken as an example for investigating the effects of capsules on the self-healing efficiency and mechanical properties of cementitious materials. The efficiency of supply of water by using capsules as a function of capsule dosages and sizes was determined numerically. By knowing the amount of water supplied via capsules, the efficiency of self-healing due to further hydration of unhydrated cement was quantified. In addition, the impact of capsules on mechanical properties was investigated numerically. The amount of released water increases with the dosage of capsules at different slops as the size of capsules varies. Concerning the best efficiency of self-healing, the optimizing size of capsules is 6.5 mm for capsule dosages of 3%, 5%, and 7%, respectively. Both elastic modulus and tensile strength of cementitious materials decrease with the increase of capsule. The decreasing tendency of tensile strength is larger than that of elastic modulus. However, it was found that the increase of positive effect (the capacity of inducing self-healing) of capsules is larger than that of negative effects (decreasing mechanical properties) when the dosage of capsules increases.

scholarly journals Effect of Annealing Process on the Mechanical Properties of X70 Pipeline Steel

2018 ◽  
Vol 186 ◽  
pp. 02001
Author(s):  
Teng-wei Zhu ◽  
Cheng-liang Miao ◽  
Zheng Cheng ◽  
Zhipeng Wang ◽  
Yang Cui ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Annealing Temperature ◽  
Pipeline Steel ◽  
Annealing Process ◽  
X70 Pipeline Steel ◽  
Grain Sizes ◽  
Scanning Electron

The influence of the mechanical properties of X70 pipeline steel under different annealing temperature was studied. The corresponding microstructure was investigated by the Field Emission Scanning Electron Microscopy. The results showed that the yield strength and the tensile strength both experienced from rise to decline with the increase of annealing temperature. The grain sizes were coarse and a large amount of cementite precipitated due to preserving temperature above 550 °, which induced matrix fragmentation and deteriorate the -10 ° DWTT Toughness. There were little changes on the microstructure and mechanical properties when the annealing temperature was under 500 °.

Sign in / Sign up

Export Citation Format

Share Document