Effect of Active Magnesia on the Properties of Cementitious Binders

2012 ◽  
Vol 1488 ◽  
Author(s):  
Jing Zhu ◽  
Nan Ye ◽  
Jianwen Liu ◽  
Yalin Li ◽  
Jiakuan Yang
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Sem Analysis ◽  
Rapid Expansion ◽  
X Ray Diffraction ◽  
Initial Stage ◽  
Cementitious Binder ◽  
Negative Effect ◽  
The Dead

ABSTRACTReactive magnesium oxide (magnesia, MgO) was produced by calcining magnesite at comparatively low temperature, less than 800 ℃C. The reactive MgO and fly ash were used as additives to cementitious binder. The reactive MgO-ordinary Portland cement-fly ash is referred to as MgO-OPC-FA cement in further. The hydration expansion effect of active magnesia on the properties of cementitious binder in different mixing ratio was investigated. It is known that the “dead burnt” MgO reacts with water very slowly, which causes the expansion after the solidification of cement. Therefore, the MgO content in ordinary cement is commonly restricted to less than 5%. Effects of reactive MgO on the expansion properties of the cementitious binders were studied. Hydrated products of reactive MgO cements were investigated by X-ray diffraction (XRD) and Scanning electron microscope (SEM) analysis. The MgO-OPC-FA cement was sound, although the content of reactive MgO in cement was about 8 wt. %. Reactive MgO was hydrated at early age in 24 hours, thus causing rapid expansion. Mg(OH)2appeared on initial stage of cement hydration for active magnesia. The hydration rate of active magnesia was not equal to that of the dead burnt magnesia. The hydration of reactive MgO has a negative effect on the mechanical properties of reactive MgO-ordinary Portland cement-fly ash system, in spite of the inhibitive effect of the expansion of MgO hydration produced by fly ash. Our results shed light on the potential utilization of reactive MgO in the manufacturing of cementitious binders.

scholarly journals Strength Development and Elemental Distribution of Dolomite/Fly Ash Geopolymer Composite under Elevated Temperature

Materials ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 1015 ◽  
Author(s):  
Emy Aizat Azimi ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Petrica Vizureanu ◽  
Mohd Arif Anuar Mohd Salleh ◽  
Andrei Victor Sandu ◽  
...  
Keyword(s):  
Elevated Temperature ◽  
Fly Ash ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Raw Materials ◽  
Liquid Sodium ◽  
Strength Development ◽  
Elemental Distribution ◽  
Distribution Analysis ◽  
Geopolymer Composites

A geopolymer has been reckoned as a rising technology with huge potential for application across the globe. Dolomite refers to a material that can be used raw in producing geopolymers. Nevertheless, dolomite has slow strength development due to its low reactivity as a geopolymer. In this study, dolomite/fly ash (DFA) geopolymer composites were produced with dolomite, fly ash, sodium hydroxide, and liquid sodium silicate. A compression test was carried out on DFA geopolymers to determine the strength of the composite, while a synchrotron Micro-Xray Fluorescence (Micro-XRF) test was performed to assess the elemental distribution in the geopolymer composite. The temperature applied in this study generated promising properties of DFA geopolymers, especially in strength, which displayed increments up to 74.48 MPa as the optimum value. Heat seemed to enhance the strength development of DFA geopolymer composites. The elemental distribution analysis revealed exceptional outcomes for the composites, particularly exposure up to 400 °C, which signified the homogeneity of the DFA composites. Temperatures exceeding 400 °C accelerated the strength development, thus increasing the strength of the DFA composites. This appears to be unique because the strength of ordinary Portland Cement (OPC) and other geopolymers composed of other raw materials is typically either maintained or decreases due to increased heat.

A trial construction of high durability railway viaducts with local aggregates

2019 ◽  
Author(s):  
Kotaro Kawamura ◽  
Joe Takemura ◽  
Shigenobu Iguchi ◽  
Tsutomu Yoshida ◽  
Masashi Kobayashi
Keyword(s):  
Fly Ash ◽  
Side Effects ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
The Other ◽  
Strength Concrete ◽  
High Durability ◽  
Sound Barrier ◽  
Early Strength ◽  
Structural Measure

<p>We are carrying out a construction project of new railroad viaducts. These new railroad viaducts are constructing using about 110,000 m<span>3</span> volume concrete. In this construction place, it is difficult for us to get low ASR-reactive aggregates and it is expected to be supplied with snowmelt water on the viaducts in winter. Then we tested ASR-reactive these local aggregates and found an effective mixed ratio of fly-ash is 20% of cement. On the other hand, various side effects were also expected by using fly-ash. For example, initial cracking due to contraction, early strength concrete, bleeding, etc. Therefore, we repeated various tests and examined and carried out a method that could ensure the same construction method and quality as when using ordinary Portland cement, even with fly-ash. Also, we adopted a structure that is unlikely to be affected by rainwater as a structural measure. For example, the entire adoption of a ramen type viaduct that has eliminated bearings, adoption of FRP sound barrier, etc. Then we made it possible to build highly durable railway viaducts by these various measures of materials and structures.</p>

High Performance Concrete with Ternary Binders

2018 ◽  
Vol 761 ◽  
pp. 120-123 ◽  
Author(s):  
Vlastimil Bílek ◽  
David Pytlík ◽  
Marketa Bambuchova
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Silica Fume ◽  
High Performance ◽  
Ordinary Portland Cement ◽  
High Performance Concrete ◽  
Fresh Concrete ◽  
Binder Ratio ◽  
Water To Binder Ratio ◽  
Condensed Silica Fume

Use a ternary binder for production of a high performance concrete with a compressive strengths between 120 and 170 MPa is presented. The water to binder ratio of the concrete is 0.225 and the binder is composed of Ordinary Portland Cement (OPC), condensed silica fume (CSF), ground limestone (L), fly ash (FA) and metakaoline (MK). The dosage of (M + CSF) is kept at a constant level for a better workability of fresh concrete. Different workability, flexural and compressive strengths were obtained for concretes with a constant cement and a metakaoline dosage, and for a constant dosage (FA + L) but a different ratio FA / L. An optimum composition was found and concretes for other tests were designed using this composition.

Research on Solid Wastes of Gangue, Slag, Fly Ash Used as Cement Composite Mixing Materials

2011 ◽  
Vol 415-417 ◽  
pp. 1486-1489
Author(s):  
Jian Guo Liao ◽  
Qian Ma ◽  
Yi Shun Zhang ◽  
Zhi Yang Song ◽  
Kai Hang Liu ◽  
...  
Keyword(s):  
Fly Ash ◽  
Cement Composite ◽  
Sem Analysis ◽  
Solid Wastes ◽  
X Ray Diffraction ◽  
Compact Structure ◽  
X Ray ◽  
Before And After ◽  
Mixed Material ◽  
Cement Strength

The purpose of this study is to bring the fly ash, coal gangue and slag industrial solid wastes which contain the chemical composition for activation treatment, used as activated composite cement mixing materials, through strength test shows that the compound mixing materials impermeability activation treatment can obviously increase the cement strength. X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) analysis results showed that the crystal structure of the mixed material calcined before and after have apparent change. There are lesss hydration products with compact structure of cement hydration 3d. The early strength of aiding composite mixing materials cement improved greatly.

Mechanical Properties of Class C High Volume Fly Ash Concrete with Lime Water as Mixing Water

2014 ◽  
Vol 660 ◽  
pp. 312-316
Author(s):  
Mochamad Solikin ◽  
Budi Setiawan
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Flexural Strength ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
High Volume ◽  
Fly Ash Concrete ◽  
Lime Water ◽  
High Volume Fly Ash ◽  
Mixing Water

This paper reports an investigation on mechanical properties of high volume fly ash (HVFA) concrete produced using different types of mixing water i.e. tap water and saturated lime water. The mechanical properties of ordinary Portland cement concrete are also investigated as control tests. The concrete were tested for their compressive strength, flexural strength and splitting tensile strength at the curing ages of 56 days. The results showed that strength development of high volume fly ash concrete up to 56 days is lower than ordinary portal cement. In addition, the flexural strength and splitting strength of concrete are lower than ordinary Portland cement. Moreover, the use of saturated lime water as mixing water reduces the mechanical properties of class C high volume fly ash concrete.

scholarly journals Durability Study on High Calcium Fly Ash Based Geopolymer Concrete

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
Ganesan Lavanya ◽  
Josephraj Jegan
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Sodium Hydroxide ◽  
Ordinary Portland Cement ◽  
Geopolymer Concrete ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Ordinary Portland Cement Concrete

This study presents an investigation into the durability of geopolymer concrete prepared using high calcium fly ash along with alkaline activators when exposed to 2% solution of sulfuric acid and 5% magnesium sulphate for up to 45 days. The durability was also assessed by measuring water absorption and sorptivity. Ordinary Portland cement concrete was also prepared as control concrete. The grades chosen for the investigation were M20, M40, and M60. The alkaline solution used for present study is the combination of sodium silicate and sodium hydroxide solution with the ratio of 2.50. The molarity of sodium hydroxide was fixed as 12. The test specimens were150×150×150 mm cubes,100×200 mm cylinders, and100×50 mm discs cured at ambient temperature. Surface deterioration, density, and strength over a period of 14, 28, and 45 days were observed. The results of geopolymer and ordinary Portland cement concrete were compared and discussed. After 45 days of exposure to the magnesium sulfate solution, the reduction in strength was up to 12% for geopolymer concrete and up to 25% for ordinary Portland cement concrete. After the same period of exposure to the sulphuric acid solution, the compressive strength decrease was up to 20% for geopolymer concrete and up to 28% for ordinary Portland cement concrete.

Sign in / Sign up

Export Citation Format

Share Document