scholarly journals The influence of particle composition in a three-layer particleboard on its physical and mechanical properties

2012 ◽  
Vol 49 (No. 2) ◽  
pp. 83-93 ◽  
Author(s):  
J. Hrázský ◽  
P. Král
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Particle Composition ◽  
Wood Processing

The paper deals with results of research aimed at the problem of the maximum possible amount of added sawdust to standard particles into surface and central layers of three-layer particleboards in order that the physical and mechanical properties of particleboards will comply with the CSN 49 2614 Standard. Waste from wood processing is widely used for the production of particleboards. For that purpose, three-layer particleboards with computed density of 740 kg/m3 at seven versions A-G with 0–30% sawdust addition to standard particles were manufactured in a laboratory. Five particleboards 500 × 500 × 16 mm were made for each version. These air-conditioned particleboards were cut into specimens in which physical and mechanical properties such as moisture, density, swelling, perpendicular tensile strength and bending strength were determined. It is obvious from the results of physical and mechanical properties that during the production of particleboards sawdust at a quantity of max. 25% can be added to standard particles when all values of physical and mechanical properties are in accordance with the CSN 49 2614 Standard.

scholarly journals Mechanical and Physical Properties of Polyester Reinforced Glass Fibre/Orange Peel Particulate Hybrid Composite

2019 ◽  
Vol 7 (1) ◽  
pp. 18-26
Author(s):  
Rabiu Onoruoiza Mamman ◽  
Aliyu Mohammed Ramalan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Bending Strength ◽  
Unsaturated Polyester ◽  
Glass Fibers ◽  
Physical And Mechanical Properties ◽  
Orange Peel ◽  
Constant Weight ◽  
Weight Percentage ◽  
Particulate Reinforcement

This study was focused on the development of hybrid composed using orange peel particulate dispersed in an unsaturated polyester resin reinforced with chopped strands of E-glass fibers. Orange peel particulate of about 350µm sieve size, of varying weight percentage (3, 6, 9,12 and 15) wt.% and E-glass fiber of constant weight percentage 25.1wt% was used as reinforcements in a polyester matrix. The effect of the orange peel particulate on the physical and mechanical properties of the resulting composite such as tensile strength, bending strength, impact strength and hardness strength was investigated. The results showed remarkable improvement in mechanical properties with increase in percentage of particulate reinforcement. Tensile strength varies from 50.0 to 62.6 MPa, Hardness values varies between 28.6 and 40.8HRB, Impact energy at room temperature, varies between 5.0 to 7.4 Joules, as a function of fiber weight fractions and the flexural strength varies from 74.0 to 85.2 MPa. The best mechanical properties were obtained at 15 Wt.% particulate reinforcements. The results of the physical tests show that the water absorption increases as the weight percentage of the particulate reinforcement increases and the same condition also holds for the density.

Study and Evaluation on Physical and Mechanical Properties of 40 Kinds of Wood Species in Zhejiang Province (China)

2014 ◽  
Vol 962-965 ◽  
pp. 657-662
Author(s):  
Man Ping Xu ◽  
Fei Yan Guo ◽  
Kan Kan Zhou ◽  
Wei Ming Yang
Keyword(s):  
Mechanical Properties ◽  
Wood Species ◽  
Bending Strength ◽  
Comprehensive Evaluation ◽  
Physical And Mechanical Properties ◽  
Zhejiang Province ◽  
Modulus Of Rupture ◽  
Processing Application ◽  
Wood Processing ◽  
Analysis Methods

Physical and mechanical properties of 40 kinds of typical wood species in Zhejiang province were studied in this experiment. Density, shrinkage rate, modulus of rupture,bending strength, compression strength, shear strength and hardness were measured and wood species were classified and evaluated by clustering analysis mehtod (CA) combined with membership function (MF) comprehensive evaluation according to these properties. The results showed that the two analysis methods achieved the similar results when screening first class wood which can be conclued that among the 40 kinds of species Quercus fabri, Dalbergia hupeana Cyclobalanopsis glauca, Lithocarpus harlandii and Lagerstroemia indica were the excellent quality. In the mean while the two analysis methods got the similar conclusion that wood properties of Pterocarya stenoptera were the worest as well. In addation, Camptotheca acuminata and Alniphyllum fortune according to CA and Ilex rotunda, and Cyclocarya paliurus according to MF were also the worest qulaity. The study provided powerful references for wood processing, application and directional cultivation of indigenous tree species in Zhejiang.

Structure and properties of compact articles from high-alloyed iron powder with adding of boron nitride

2020 ◽  
pp. 39-48
Author(s):  
B. O. Bolshakov ◽  
◽  
R. F. Galiakbarov ◽  
A. M. Smyslov ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Grain Boundary ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Operating Conditions ◽  
Structure And Properties ◽  
Steam Turbines ◽  
Friction Forces ◽  
Wide Range

The results of the research of structure and properties of a composite compact from 13 Cr – 2 Мо and BN powders depending on the concentration of boron nitride are provided. It is shown that adding boron nitride in an amount of more than 2% by weight of the charge mixture leads to the formation of extended grain boundary porosity and finely dispersed BN layers in the structure, which provides a high level of wearing properties of the material. The effect of boron nitride concentration on physical and mechanical properties is determined. It was found that the introduction of a small amount of BN (up to 2 % by weight) into the compacts leads to an increase in plasticity, bending strength, and toughness by reducing the friction forces between the metal powder particles during pressing and a more complete grain boundary diffusion process during sintering. The formation of a regulated structure-phase composition of powder compacts of 13 Cr – 2 Mо – BN when the content of boron nitride changes in them allows us to provide the specified physical and mechanical properties in a wide range. The obtained results of studies of the physical and mechanical characteristics of the developed material allow us to reasonably choose the necessary composition of the powder compact for sealing structures of the flow part of steam turbines, depending on their operating conditions.

scholarly journals Damage Evolution of Granodiorite after Heating and Cooling Treatments

Minerals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 779
Author(s):  
Mohamed Gomah ◽  
Guichen Li ◽  
Salah Bader ◽  
Mohamed Elkarmoty ◽  
Mohamed Ismael
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Failure Mode ◽  
Physical And Mechanical Properties ◽  
P Wave ◽  
Physical Parameters ◽  
Slow Cooling ◽  
Heating And Cooling ◽  
Natural Rock ◽  
The Impact

The awareness of the impact of high temperatures on rock properties is essential to the design of deep geotechnical applications. The purpose of this research is to assess the influence of heating and cooling treatments on the physical and mechanical properties of Egyptian granodiorite as a degrading factor. The samples were heated to various temperatures (200, 400, 600, and 800 °C) and then cooled at different rates, either slowly cooled in the oven and air or quickly cooled in water. The porosity, water absorption, P-wave velocity, tensile strength, failure mode, and associated microstructural alterations due to thermal effect have been studied. The study revealed that the granodiorite has a slight drop in tensile strength, up to 400 °C, for slow cooling routes and that most of the physical attributes are comparable to natural rock. Despite this, granodiorite thermal deterioration is substantially higher for quick cooling than for slow cooling. Between 400:600 °C is ‘the transitional stage’, where the physical and mechanical characteristics degraded exponentially for all cooling pathways. Independent of the cooling method, the granodiorite showed a ductile failure mode associated with reduced peak tensile strengths. Additionally, the microstructure altered from predominantly intergranular cracking to more trans-granular cracking at 600 °C. The integrity of the granodiorite structure was compromised at 800 °C, the physical parameters deteriorated, and the rock tensile strength was negligible. In this research, the temperatures of 400, 600, and 800 °C were remarked to be typical of three divergent phases of granodiorite mechanical and physical properties evolution. Furthermore, 400 °C could be considered as the threshold limit for Egyptian granodiorite physical and mechanical properties for typical thermal underground applications.

scholarly journals Thermal, Physical and Mechanical Properties of Poly(Butylene Succinate)/Kenaf Core Fibers Composites Reinforced with Esterified Lignin

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2359
Author(s):  
Harmaen Ahmad Saffian ◽  
Masayuki Yamaguchi ◽  
Hidayah Ariffin ◽  
Khalina Abdan ◽  
Nur Kartinee Kassim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Loss Modulus ◽  
Physical And Mechanical Properties ◽  
Weight Percent Gain ◽  
Weight Percent ◽  
Esterification Reaction ◽  
Butylene Succinate ◽  
Kenaf Core ◽  
Modified Lignin

In this study, Kraft lignin was esterified with phthalic anhydride and was served as reinforcing filler for poly(butylene succinate) (PBS). Composites with different ratios of PBS, lignin (L), modified lignin (ML) and kenaf core fibers (KCF) were fabricated using a compounding method. The fabricated PBS composites and its counterparts were tested for thermal, physical and mechanical properties. Weight percent gain of 4.5% after lignin modification and the FTIR spectra has confirmed the occurrence of an esterification reaction. Better thermo-mechanical properties were observed in the PBS composites reinforced with modified lignin and KCF, as higher storage modulus and loss modulus were recorded using dynamic mechanical analysis. The density of the composites fabricated ranged from 1.26 to 1.43 g/cm3. Water absorption of the composites with the addition of modified lignin is higher than that of composites with unmodified lignin. Pure PBS exhibited the highest tensile strength of 18.62 MPa. Incorporation of lignin and KCF into PBS resulted in different extents of reduction in tensile strength (15.78 to 18.60 MPa). However, PBS composite reinforced with modified lignin exhibited better tensile and flexural strength compared to its unmodified lignin counterpart. PBS composite reinforced with 30 wt% ML and 20 wt% KCF had the highest Izod impact, as fibers could diverge the cracking propagation of the matrix. The thermal conductivity value of the composites ranged from 0.0903 to 0.0983 W/mK, showing great potential as a heat insulator.

scholarly journals Eco-Friendly, High-Density Fiberboards Bonded with Urea-Formaldehyde and Ammonium Lignosulfonate

Polymers ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 220
Author(s):  
Petar Antov ◽  
Viktor Savov ◽  
Ľuboš Krišťák ◽  
Roman Réh ◽  
George I. Mantanis
Keyword(s):  
Mechanical Properties ◽  
Bending Strength ◽  
Urea Formaldehyde ◽  
Physical And Mechanical Properties ◽  
High Density ◽  
Thickness Swelling ◽  
Formaldehyde Content ◽  
Uf Resin ◽  
Natural Wood ◽  
European Standards

The potential of producing eco-friendly, formaldehyde-free, high-density fiberboard (HDF) panels from hardwood fibers bonded with urea-formaldehyde (UF) resin and a novel ammonium lignosulfonate (ALS) is investigated in this paper. HDF panels were fabricated in the laboratory by applying a very low UF gluing factor (3%) and ALS content varying from 6% to 10% (based on the dry fibers). The physical and mechanical properties of the fiberboards, such as water absorption (WA), thickness swelling (TS), modulus of elasticity (MOE), bending strength (MOR), internal bond strength (IB), as well as formaldehyde content, were determined in accordance with the corresponding European standards. Overall, the HDF panels exhibited very satisfactory physical and mechanical properties, fully complying with the standard requirements of HDF for use in load-bearing applications in humid conditions. Markedly, the formaldehyde content of the laboratory fabricated panels was extremely low, ranging between 0.7–1.0 mg/100 g, which is, in fact, equivalent to the formaldehyde release of natural wood.

Effect of Castor Oil Impregnation on the Physical and Mechanical Properties of Bacterial Cellulose

2012 ◽  
Vol 3 (1) ◽  
pp. 13-26
Author(s):  
Myrtha Karina ◽  
Lucia Indrarti ◽  
Rike Yudianti ◽  
Indriyati
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Bacterial Cellulose ◽  
Young’S Modulus ◽  
Castor Oil ◽  
Young's Modulus ◽  
Physical And Mechanical Properties ◽  
Scanning Electron Micrographs ◽  
Elongation At Break ◽  
Acetone Water

The effect of castor oil on the physical and mechanical properties of bacterial cellulose is described. Bacterial cellulose (BC) was impregnated with 0.5–2% (w/v) castor oil (CO) in acetone–water, providing BCCO films. Scanning electron micrographs revealed that the castor oil penetrated the pores of the bacterial cellulose, resulting in a smoother morphology and enhanced hydrophilicity. Castor oil caused a slight change in crystallinity indices and resulted in reduced tensile strength and Young's modulus but increased elongation at break. A significant reduction in tensile strength and Young's modulus was achieved in BCCO films with 2% castor oil, and there was an improvement in elongation at break and hydrophilicity. Impregnation with castor oil, a biodegradable and safe plasticiser, resulted in less rigid and more ductile composites.

scholarly journals Enhancement of Mechanical Properties and Porosity of Concrete Using Steel Slag Coarse Aggregate

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2865
Author(s):  
Md Jihad Miah ◽  
Md. Munir Hossain Patoary ◽  
Suvash Chandra Paul ◽  
Adewumi John Babafemi ◽  
Biranchi Panda
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Microstructural Analysis ◽  
Steel Slag ◽  
Physical And Mechanical Properties ◽  
Length Change ◽  
Sustainable Building ◽  
Burnt Clay ◽  
Lower Porosity ◽  
Furnace Steel

This paper investigates the possibility of utilizing steel slags produced in the steelmaking industry as an alternative to burnt clay brick aggregate (BA) in concrete. Within this context, physical, mechanical (i.e., compressive and splitting tensile strength), length change, and durability (porosity) tests were conducted on concrete made with nine different percentage replacements (0%, 10%, 20%, 30%, 40%, 50%, 60%, 80%, and 100% by volume of BA) of BA by induction of furnace steel slag aggregate (SSA). In addition, the chemical composition of aggregate through X-ray fluorescence (XRF) analysis and microstructural analysis through scanning electron microscopy (SEM) of aggregates and concrete were performed. The experimental results show that the physical and mechanical properties of concrete made with SSA were significantly higher than that of concrete made with BA. The compressive and tensile strength increased by 73% when SSA fully replaced BA. The expansion of concrete made with SSA was a bit higher than the concrete made with BA. Furthermore, a significant lower porosity was observed for concrete made with SSA than BA, which decreased by 40% for 100% SSA concrete than 100% BA concrete. The relation between compressive and tensile strength with the porosity of concrete mixes are in agreement with the relationships presented in the literature. This study demonstrates that SSA can be used as a full replacement of BA, which is economical, conserves the natural aggregate, and is sustainable building material since burning brick produces a lot of CO2.

scholarly journals Composites from Thermoplastic Natural Rubber Reinforced Rubberwood Sawdust: Effects of Sawdust Size and Content on Thermal, Physical, and Mechanical Properties

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Chatree Homkhiew ◽  
Surasit Rawangwong ◽  
Worapong Boonchouytan ◽  
Wiriya Thongruang ◽  
Thanate Ratanawilai
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
High Density Polyethylene ◽  
High Performance ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Shore Hardness ◽  
Thermoplastic Natural Rubber ◽  
Plastic Content

The aim of this work is to investigate the effects of rubberwood sawdust (RWS) size and content as well as the ratio of natural rubber (NR)/high-density polyethylene (HDPE) blend on properties of RWS reinforced thermoplastic natural rubber (TPNR) composites. The addition of RWS about 30–50 wt% improved the modulus of the rupture and tensile strength of TPNR composites blending with NR/HDPE ratios of 60/40 and 50/50. TPNR composites reinforced with RWS 80 mesh yielded better tensile strength and modulus of rupture than the composites with RWS 40 mesh. The TPNR/RWS composites with larger HDPE content gave higher tensile, flexural, and Shore hardness properties and thermal stability as well as lower water absorption. The TPNR/RWS composites with larger plastic content were therefore suggested for applications requiring high performance of thermal, physical, and mechanical properties.

Effect of Wood Filler Concentration on Physical and Mechanical Properties of PLA-Based Composites

2021 ◽  
Vol 887 ◽  
pp. 110-115
Author(s):  
G.A. Sabirova ◽  
R.R. Safin ◽  
N.R. Galyavetdinov
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Composite Materials ◽  
Impact Strength ◽  
Wood Flour ◽  
Experimental Studies ◽  
Physical And Mechanical Properties ◽  
Filler Concentration ◽  
High Concentration

This paper presents the findings of experimental studies of the physical and mechanical properties of wood-filled composites based on polylactide (PLA) and vegetable filler in the form of wood flour (WF) thermally modified at 200-240 °C. It also reveals the dependence of the tensile strength, impact strength, bending elastic modulus, and density of composites on the amount of wood filler and the temperature of its thermal pre-modification. We established that an increase in the concentration of the introduced filler and the degree of its heat treatment results in a decrease of the tensile strength, impact strength and density of composite materials, while with a lower binder content, thermal modification at 200 °C has a positive effect on bending elastic modulus. We also found that 40 % content of a wood filler heated to 200 °C is sufficient to maintain relatively high physical and mechanical properties of composite materials. With a higher content of a wood filler, the cost can be reduced but the quality of products made of this material may significantly deteriorate. However, depending on the application and the life cycle of this product, it is possible to develop a formulation that includes a high concentration of filler.

Sign in / Sign up

Export Citation Format

Share Document