scholarly journals On-Board Ultrasonic Water-in-Diesel Emulsion (WiDE) Fuel System for Low-Emission Diesel Engine Combustion

2018 ◽  
Vol 118 (2) ◽  
pp. 43
Author(s):  
Kotaro Kojima ◽  
Jun Kojima
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Combustion Efficiency ◽  
Biodiesel Fuel ◽  
Promising Alternative ◽  
Fuel Injectors ◽  
Fuel Supply ◽  
Diesel Fuels ◽  
Low Emission ◽  
Biodiesel Fuels

Water-in-diesel emulsion (WiDE) fuel is a promising alternative fuel capable of reducing nitrogen oxides (NOX) and particulate matter (PM) in diesel engine exhaust while simultaneously preserving combustion efficiency of the engine. However, the instability of WiDE fuel—and the high costs of production and transportation—hinder its commercialization and widespread use. An on-board ultrasonic WiDE fuel supply system is proposed as a solution to this challenge. This system allows diesel fuel and water to be continuously emulsified on-board a diesel vehicle. Diesel fuel and water, stored in individual reservoirs, are conveyed in specific ratios to an in-line mixing chamber and are rapidly homogenized by ultrasonic cavitation before entering the fuel injectors. The produced emulsion fuel is then supplied to the engine. A proof-of-concept study was conducted to compare exhaust emissions between emulsion fuels and conventional fuels. Open-flame combustion experiments were conducted using a lab-scale burner to test the system with both diesel and biodiesel fuels. Unique optical diagnostics and image-processing techniques were used to estimate PM emission levels. Results showed a reduction of PM with the use of the on-board WiDE system compared to traditional diesel fuels. PM emissions from biodiesel fuel were reduced by 58% when water-in-biodiesel emulsion was combusted with 2% water. Additionally, a PM emission reduction of 35% was achieved through emulsification of diesel fuel with 2% water. This prototype demonstrates the potential for the on-board WiDE fuel supply concept to both overcome the traditional barriers hindering the commercialization of WiDE fuel and preserve its low-emission and superior combustion efficiency characteristics.

scholarly journals An investigation of effect of biodiesel and aviation fuel jeta-1 mixtures performance and emissions on diesel engine

2014 ◽  
Vol 18 (1) ◽  
pp. 239-247 ◽  
Author(s):  
Hasan Yamik
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Chemical Properties ◽  
Engine Performance ◽  
Combustion Efficiency ◽  
Aviation Fuel ◽  
Aviation Industry ◽  
Performance And Emission ◽  
Performance And Emissions ◽  
Biodiesel Fuels

Biodiesel is an alternative fuel for diesel engines which doesn?t contain pollutants and sulfur; on the contrary it contains oxygen. In addition, both physical and chemical properties of sunflower oil methyl ester (SME) are identical to diesel fuel. Conversely, diesel and biodiesel fuels are widely used with some additives to reduce viscosity, increase the amount of cetane, and improve combustion efficiency. This study uses diesel fuel, SME and its mixture with aviation fuel JetA-1 which are widely used in the aviation industry. . Fuel mixtures were used in 1-cylinder, 4-stroke diesel engine under full load and variable engine speeds. In this experiment, engine performance and emission level are investigated. As a conclusion, as the JetA-1 ratio increases in the mixture, lower nitrogen oxide (NOx) emission is measured. Also, specific fuel consumption is lowered.

scholarly journals Experimental investigations on diesel engine using alumina nanoparticle fuel additive

2021 ◽  
Vol 13 (2) ◽  
pp. 168781402098840
Author(s):  
Mohammed S Gad ◽  
Sayed M Abdel Razek ◽  
PV Manu ◽  
Simon Jayaraj
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Alumina Nanoparticles ◽  
Experimental Investigations ◽  
Fuel Additive ◽  
Alumina Nanoparticle ◽  
Fuel Injectors ◽  
Performance And Emission ◽  
And Performance ◽  
The Impact

Experimental work was done to examine the impact of diesel fuel with alumina nanoparticles on combustion characteristics, emissions and performance of diesel engine. Alumina nanoparticles were mixed with crude diesel in various weight fractions of 20, 30, and 40 mg/L. The engine tests showed that nano alumina addition of 40 ppm to pure diesel led to thermal efficiency enhancement up to 5.5% related to the pure diesel fuel. The average specific fuel consumption decrease about neat diesel fuel was found to be 3.5%, 4.5%, and 5.5% at dosing levels of 20, 30, and 40 ppm, respectively at full load. Emissions of smoke, HC, CO, and NOX were found to get diminished by about 17%, 25%, 30%, and 33%, respectively with 40 ppm nano-additive about diesel operation. The smaller size of nanoparticles produce fuel stability enhancement and prevents the fuel atomization problems and the clogging in fuel injectors. The increase of alumina nanoparticle percentage in diesel fuel produced the increases in cylinder pressure, cylinder temperature, heat release rate but the decreases in ignition delay and combustion duration were shown. The concentration of 40 ppm alumina nanoparticle is recommended for achieving the optimum improvements in the engine’s combustion, performance and emission characteristics.

Performance Investigation of a Four Stroke Diesel Engine, Using Water-Based Ferrofluid as an Additive

2011 ◽  
Author(s):  
F. Daneshvar ◽  
N. Jahani ◽  
M. B. Shafii
Keyword(s):  
Experimental Study ◽  
Magnetic Nanoparticles ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Brake Specific Fuel Consumption ◽  
Engine Exhaust ◽  
Brake Thermal Efficiency ◽  
Diesel Fuels ◽  
Water Based

In this experimental study, a four stroke diesel engine was conducted to investigate the effect of adding water-based ferrofluid to diesel fuel on engine performance. To our knowledge, Magnetic nanoparticles had not been used before. To this end, emulsified diesel fuels of 0, 0.4, and 0.8 water-based ferrofluid/Diesel ratios by volume were used as fuel. The ferrofluid used in this study was a handmade water-based ferrofluid prepared by the authors. The results show that adding water-based ferrofluid to diesel fuel has a perceptible effect on engine performance, increasing the brake thermal efficiency relatively up to 12%, and decreasing the brake specific fuel consumption relatively up to 11% as compared to diesel fuel. In addition, the results indicate that increasing ferrofluid concentration will magnify the results. Furthermore, it was found that magnetic nanoparticles can be collected at the engine exhaust using magnetic bar.

Spray and Combustion Characteristics of Biodiesel∕Diesel Blended Fuel in a Direct Injection Common-Rail Diesel Engine

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Hyun Kyu Suh ◽  
Hyun Gu Roh ◽  
Chang Sik Lee
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Injection Rate ◽  
Combustion Characteristics ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Pilot Injection ◽  
Blended Fuel ◽  
Conventional Diesel Fuel

The aim of this work is to investigate the effect of the blending ratio and pilot injection on the spray and combustion characteristics of biodiesel fuel and compare these factors with those of diesel fuel in a direct injection common-rail diesel engine. In order to study the factors influencing the spray and combustion characteristics of biodiesel fuel, experiments involving exhaust emissions and engine performance were conducted at various biodiesel blending ratios and injection conditions for engine operating conditions. The macroscopic and microscopic spray characteristics of biodiesel fuel, such as injection rate, split injection effect, spray tip penetration, droplet diameter, and axial velocity distribution, were compared with the results from conventional diesel fuel. For biodiesel blended fuel, it was revealed that a higher injection pressure is needed to achieve the same injection rate at a higher blending ratio. The spray tip penetration of biodiesel fuel was similar to that of diesel. The atomization characteristics of biodiesel show that it has higher Sauter mean diameter and lower spray velocity than conventional diesel fuel due to high viscosity and surface tension. The peak combustion pressures of diesel and blending fuel increased with advanced injection timing and the combustion pressure of biodiesel fuel is higher than that of diesel fuel. As the pilot injection timing is retarded to 15deg of BTDC that is closed by the top dead center, the dissimilarities of diesel and blending fuels combustion pressure are reduced. It was found that the pilot injection enhanced the deteriorated spray and combustion characteristics of biodiesel fuel caused by different physical properties of the fuel.

Optimization of mixed biofuel composition for diesel engine

2021 ◽  
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Fuel ◽  
Rapeseed Oil ◽  
Alternative Fuels ◽  
Operating Mode ◽  
Promising Alternative ◽  
Motor Fuels ◽  
Engine Combustion ◽  
Basic Characteristics

Biofuels derived from vegetable oils are known to be promising alternative fuels for diesel engines. The possibility of using mixtures of petroleum diesel fuel with rapeseed oil and rapeseed oil methyl ester as environmentally friendly motor fuels is considered. The practicability of changing the composition of these mixtures in accordance with the engine operating mode is shown. A technique for multicriteria optimization of the composition of such mixed biofuels is suggested. The basic characteristics of the optimal composition of these mixed biofuels are calculated. A device for regulating fuel’s composition is proposed. The basic characteristic of regulation of the blended biofuel composition realized by the device is presented. Keywords diesel engine; combustion chamber; oil diesel fuel; rapeseed oil; rapeseed oil methyl ester; biofuel mixture; ecological characteristics; exhaust gases toxicity

Compatibility of Palm Biodiesel Blends on the Existing Elastomer Fuel Hose in Diesel Engine with Approach of Dynamic Test Rig: A Concept Study

2020 ◽  
Vol 1010 ◽  
pp. 172-177
Author(s):  
Narisa Sa'at ◽  
Ariffin Samsuri ◽  
Noradila Abdul Latif ◽  
Nurul Fitriah Nasir ◽  
Rais Hanizam Madon ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Alternative Fuels ◽  
Dynamic Testing ◽  
Dynamic Test ◽  
Field Trials ◽  
Biodiesel Fuel ◽  
Compatibility Study ◽  
Fuel System ◽  
Experimental Conditions

Elastomer is one of the important material for the hoses, sealants and tubes in the components of fuel delivery system in diesel engine vehicles due to the factor of compatibility with diesel fuel. However, concern were arise that presence of alcohol, fatty acid component and other factors such as water content in the alternative fuels which is blended biodiesel fuel and different chemical composition from the diesel fuel may increase further uncertainty to the consumer of diesel engine or diesel engine manufacturers in terms of compatibility issue. Thus this paper intends to assess current and typical test standards on their efficacy of representing the fuel system of diesel engine vehicles. Respectively, ASTM D471 are based on laboratory immersion studies and the experimental conditions are differ from the real service conditions in the fuel system of diesel engine vehicles. Even though number of previous studies regarding to the compatibility of elastomer components has been reported, there is a need to set up the exact material that present in the fuel system of diesel engine vehicles. This is especially right for elastomers since their resistance is mainly depends on their elemental compositions. As such, introduction of the dynamic testing approach that may be applied when assessing the compatibility study between blended biodiesel fuel that simulate the actual fuel system of a diesel engine vehicles before carrying out in the field trials.

scholarly journals Influence of Fuel Injection Pressure on the Emissions Characteristics and Engine Performance in a CRDI Diesel Engine Fueled with Palm Biodiesel Blends

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3837 ◽  
Author(s):  
Sam Ki Yoon ◽  
Jun Cong Ge ◽  
Nag Jung Choi
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Biodiesel Fuel ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Fuel Blend ◽  
Engine Load ◽  
Fuel Injection Pressure

This experiment investigates the combustion and emissions characteristics of a common rail direct injection (CRDI) diesel engine using various blends of pure diesel fuel and palm biodiesel. Fuel injection pressures of 45 and 65 MPa were investigated under engine loads of 50 and 100 Nm. The fuels studied herein were pure diesel fuel 100 vol.% with 0 vol.% of palm biodiesel (PBD0), pure diesel fuel 80 vol.% blended with 20 vol.% of palm biodiesel (PBD20), and pure diesel fuel 50 vol.% blended with 50 vol.% of palm biodiesel (PBD50). As the fuel injection pressure increased from 45 to 65 MPa under all engine loads, the combustion pressure and heat release rate also increased. The indicated mean effective pressure (IMEP) increased with an increase of the fuel injection pressure. In addition, for 50 Nm of the engine load, an increase to the fuel injection pressure resulted in a reduction of the brake specific fuel consumption (BSFC) by an average of 2.43%. In comparison, for an engine load of 100 Nm, an increase in the fuel injection pressure decreased BSFC by an average of 0.8%. Hydrocarbon (HC) and particulate matter (PM) decreased as fuel pressure increased, independent of the engine load. Increasing fuel injection pressure for 50 Nm engine load using PBD0, PBD20 and PBD50 decreased carbon monoxide (CO) emissions. When the fuel injection pressure was increased from 45 MPa to 65 MPa, oxides of nitrogen (NOx) emissions were increased for both engine loads. For a given fuel injection pressure, NOx emissions increased slightly as the biodiesel content in the fuel blend increased.

Emissions Characteristics of a Diesel Engine with GTL and Biodiesel Fuels

2014 ◽  
Vol 1008-1009 ◽  
pp. 995-1000
Author(s):  
Pi Qiang Tan ◽  
Shu Wang ◽  
Yuan Hu Zhi ◽  
Di Ming Lou
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Emission Characteristics ◽  
Nox Emissions ◽  
Brake Specific Fuel Consumption ◽  
Biodiesel Blend ◽  
Hc Emissions ◽  
Gas To Liquids ◽  
Biodiesel Fuels ◽  
Co Emission

Emission characteristics of an electronic-controlled high pressure common-rail diesel engine with low-blend Gas-to-liquids (GTL) and low-blend biodiesel fuels are studied. Pure diesel fuel, G10 fuel (10% GTL blend with diesel fuel) and B10 fuel (10% biodiesel blend with diesel fuel) are used in this research. The results show that torque of the engine with pure diesel fuel is higher than G10 fuel, and B10 fuel is the lowest. Compared to the pure diesel fuel, the brake specific fuel consumption (BSFC) of the engine with G10 fuel decreases, but the B10 fuel increases slightly. Hydrocarbon (HC) emissions of the engine with G10 fuel or B10 fuel are lower than the pure diesel fuel, and the carbon monoxide (CO) emission increases slightly, and nitrogen oxides (NOx) emissions have no distinct change. Compared to the G10 fuel, the CO and HC emissions of the engine with B10 fuel are lower.

scholarly journals ANALYSIS OF THE ECOLOGICAL PARAMETERS OF THE DIESEL ENGINE POWERED WITH BIODIESEL FUEL CONTAINING METHYL ESTERS FROM CAMELINA SATIVA OIL

Transport ◽  
2010 ◽  
Vol 25 (1) ◽  
pp. 22-28 ◽  
Author(s):  
Sergejus Lebedevas ◽  
Galina Lebedeva ◽  
Violeta Makarevičienė ◽  
Irina Kazanceva ◽  
Kiril Kazancev
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Methyl Esters ◽  
Chemical Properties ◽  
Acid Methyl Ester ◽  
Fuel Mixture ◽  
Camelina Sativa ◽  
Biodiesel Fuel ◽  
Load Range ◽  
Acid Methyl

The article explores the possibilities of using fatty acid methyl esters derived from the oil of a new species of oily plant Camelina sativa not demanding on soil. The performed research on the physical and chemical properties of pure methyl esters from Camelina sativa show that biofuels do not meet requirements for the biodiesel fuel standard (LST EN 14214:2009) of a high iodine value and high content of linoleic acid methyl ester, so they must be mixed with methyl esters produced from pork lard the content of which in the mixture must be not less than 32%. This article presents the results of tests on combustion emission obtained when three‐cylinder diesel engine VALMET 320 DMG was fuelled with a mixture containing 30% of this new kind of fuel with fossil diesel fuel comparing with emissions obtained when the engine was fuelled with a fuel mixture containing 30% of conventional biodiesel fuel (rapeseed oil methyl esters) with fossil diesel fuel. The obtained results show that using both types of fuel, no significant differences in CO and NOx concentrations were observed throughout the tested load range. When operating on fuels containing methyl esters from Camelina sativa, HC emissions decreased by 10 to 12% and the smokeness of exhaust gas by 12 to 25%.

Sign in / Sign up

Export Citation Format

Share Document