scholarly journals Degradation Mechanism of Methyl Orange by Pyrite-Activated Persulfate

2021 ◽  
Author(s):  
Hui Liu ◽  
Wenlong BI
Keyword(s):  
Methyl Orange ◽  
Negative Impact ◽  
Tap Water ◽  
Degradation Mechanism ◽  
Inhibitory Effect ◽  
Optimal Dosage ◽  
High Concentration ◽  
Initial Ph ◽  
Advanced Oxidation Technology ◽  
Activated Persulfate

Abstract This paper took methyl orange (MO), a typical azo dye, as the target substance to explore the degradation mechanism of pyrite (FeS2)-activated persulfate (PS) by advanced oxidation technology, and response surface methodology was used to determine the optimal dosage of FeS2 and PS. The related experiments were conducted focused on different factors and degradation mechanisms. The results showed that when the initial concentration of MO was 0.1 mM, the pyrite was 1.6 g/L and PS was 1.0 mM, the degradation rate of MO could reach 92.94% in 150 min. In the FeS2/PS system, the main free radical was sulfate radical, which contributed about 22.43% to the degradation of MO, but the hydroxyl radical contributed little. Both pH ≤ 2 and pH ≥ 10 would have an inhibitory effect on the system, and the removal effect of MO was the best at initial pH of 4. The Cl−, HCO3− and H2PO4− might play an important role in the treatment of actual wastewater. This study had shown that HCO3− in a low concentration and Cl− had little effect on the system; H2PO4− and high concentration of HCO3− could inhibit the reaction of the system. By exploring the influence of different water matrices such as tap water, river water, and distilled water, it was found that HCO3− would have a negative impact on the experiment, and the degradation effect was obviously observed when the pH was adjusted to 4. The results can provide technical support for the degradation of pyrite-activated persulfate system in printing and dyeing wastewater.

Angiotensin II-mediated biphasic regulation of proximal tubular Na+/H+ exchanger 3 is impaired during oxidative stress

2011 ◽  
Vol 301 (2) ◽  
pp. F364-F370 ◽  
Author(s):  
Anees Ahmad Banday ◽  
Mustafa F. Lokhandwala
Keyword(s):  
Oxidative Stress ◽  
Protein Kinase ◽  
Tap Water ◽  
Buthionine Sulfoximine ◽  
Inhibitory Effect ◽  
Ang Ii ◽  
Sprague Dawley ◽  
High Concentration ◽  
Nitric Oxide Signaling ◽  
Proximal Tubular

Angiotensin (ANG) II via AT1 receptors (AT1Rs) maintains sodium homeostasis by regulating renal sodium transporters including Na+/H+ exchanger 3 (NHE3) in a biphasic manner. Low-ANG II concentration stimulates whereas high concentrations inhibit NHE3 activity. Oxidative stress has been shown to upregulate AT1R function that could modulate the ANG II-mediated NHE3 regulation. This study was designed to identify the signaling pathways responsible for ANG II-mediated biphasic regulation of proximal tubular NHE3 and the effect of oxidative stress on this phenomenon. Male Sprague-Dawley rats were chronically treated with a pro-oxidant l-buthionine sulfoximine (BSO) with and without an antioxidant tempol in tap water for 3 wk. BSO-treated rats exhibited oxidative stress and high blood pressure. At low concentration (1 pM) ANG II increased NHE3 activity in proximal tubules from all animals. However, in BSO-treated rats, the stimulation was more robust and was normalized by tempol treatment. ANG II (1 pM)-mediated NHE3 activation was abolished by AT1R blocker, intracellular Ca2+ chelator, and inhibitors of phospholipase C (PLC) and Ca2+-dependent calmodulin (CaM) but it was insensitive to Giα and protein kinase C inhibitors or AT2R antagonist. A high concentration of ANG II (1 μM) inhibited NHE3 activity in control and tempol-treated rats. However, in BSO-treated rats, ANG II (1 μM) continued to induce NHE3 stimulation. Tempol restored the inhibitory effect of ANG II (1 μM) in BSO-treated rats. The inhibitory effect of ANG II (1 μM) involved AT1R-dependent, cGMP-dependent protein kinase (PKG) activation and was independent of AT2 receptor and nitric oxide signaling. We conclude that ANG II stimulates NHE3 via AT1R-PLC-CaM pathway and inhibits NHE3 by AT1R-PKG activation. Oxidative stress impaired ANG II-mediated NHE3 biphasic response in that stimulation was observed at both high- and low-ANG II concentration.

scholarly journals Use of an Ultraviolet Light activated Persulfate Process to Degrade Humic Substances: Effects of Wavelength and Persulfate Dose

2021 ◽  
Author(s):  
Yiming Fang ◽  
Hiroshi Sakai
Keyword(s):  
Hydrogen Peroxide ◽  
Molecular Weight ◽  
Drinking Water ◽  
Humic Substances ◽  
Degradation Mechanism ◽  
Treatment Plant ◽  
Drinking Water Treatment ◽  
Lower Molecular Weight ◽  
High Concentration ◽  
Activated Persulfate

Abstract Natural organic matter (NOM), commonly found in surface and ground waters, form Disinfection by-products in drinking water. Generally, advanced oxidation processes (AOPs) featuring hydrogen peroxide are used to treat water, however, sulfate radical recently has been used to treat recalcitrant organics, because it is associated with a higher oxidation potential and more effective removal than hydroxyl radicals. Hence, in this research, we evaluated persulfate oxidation efficiency in terms of reductions in humic substances levels and investigated the degradation mechanism. The results showed that ultraviolet activated persulfate effectively treated humic substances compared with hydrogen peroxide and direct irradiation. Treatment was dose- and wavelength-dependent; higher persulfate concentrations or shorter UV wavelengths were more effective for treating humic substances as high concentration sulfate radicals were created. The degradation mechanism was similar to that of hydrogen peroxide. Aromatic and chromophore components were more susceptible to degradation than were lower molecular weight components, being initially decomposed into the latter, reducing UV254 absorbance and the SUVA254. Lower molecular weight materials were eventually degraded to end products: NPOC levels fell. And we also treated the inflow of a drinking water treatment plant with persulfate, and humic substances were effectively removed.

scholarly journals A Doping Lattice of Aluminum and Copper with Accelerated Electron Transfer Process and Enhanced Reductive Degradation Performance

2016 ◽  
Vol 6 (1) ◽  
Author(s):  
Lin Zhang ◽  
Xue Gao ◽  
Zhixuan Zhang ◽  
Mingbo Zhang ◽  
Yiqian Cheng ◽  
...  
Keyword(s):  
Degradation Mechanism ◽  
High Energy ◽  
High Concentration ◽  
Cu Alloy ◽  
Cu Alloys ◽  
Zero Order Kinetics ◽  
Alloy Particles ◽  
Reductive Degradation ◽  
Initial Ph ◽  
Ft Ir

Abstract Treatment of azo dye effluents has received increasing concerns over the years due to their potential harms to natural environment and human health. The present study described the degrading ability of the as-synthesized crystalline Al-Cu alloys for removal of high-concentration Acid Scarlet 3R in alkaline aqueous solutions and its degradation mechanism. Al-Cu alloy particles with Al/Cu ratios 19:1 were successfully synthesized by high-energy mechanical milling. Characterization results showed that 10 h mechanical alloying process could lead to the formation of crystalline Al(Cu) solid solution. Batch experiment results confirmed the excellent ability of Al-Cu alloy particles for the degradation of 3R in aqueous solution. Under a certain condition ([Al-Cu]0 = 2 g/L, [3R]0 = 200 mg/L, [NaCl]0 = 25 g/L, initial pH = 10.9), the 3R could be completely degraded within only 3 min. It was also found that the degradation reaction followed zero-order kinetics model with respect to the initial dye concentration. The intermediate compounds were identified by UV-vis, FT-IR and HPLC-MS, and a pathway was proposed. Additionally, post-treatment Al-Cu alloy particles were characterized by SEM and TEM, and the results showed that the degradation might be attributed to the corrosion effect of Al-Cu alloys.

Measurement of the Platelet Response to Laser- induced Microvascular Injury

1974 ◽  
Vol 32 (02/03) ◽  
pp. 704-713 ◽  
Author(s):  
F. N McKenzie ◽  
K.-E Arfors ◽  
N. A Matheson
Keyword(s):  
Inhibitory Effect ◽  
Microvascular Blood Flow ◽  
Platelet Response ◽  
High Concentration ◽  
Platelet Activity ◽  
Microvascular Injury ◽  
Arterial Blood ◽  
Proximal Site ◽  
Adenosine Phosphates

SummaryA study has been made of the biochemical factors underlying the platelet response to laser-induced microvascular injury. A platelet aggregating substance is produced at sites of laser-induced injury which markedly stimulates platelet activity at a site of injury inflicted a short distance downstream. Distal sites of injury are not similarly influenced if the distance between the injuries is increased or if the proximal site no longer shows platelet-stimulating activity. The stimulating effect of an adjacent proximal injury on platelet activity at a distal site is inhibited by local intra-arterial infusion of adenosine. Measurements of arterial blood pressure and microvascular blood flow velocity during adenosine infusion showed that its inhibitory effect on platelet activity is largely independent of its vasodilator properties. The effect of infusion of different adenosine phosphates (AMP, ADP, ATP) was also studied. Very small amounts of ADP markedly stimulated platelet activity and the emboli formed were similar to those normally produced at sites of laser injury. At high concentration AMP inhibited while ATP stimulated platelet activity in vivo. The results emphasise the fundamental role of ADP as a mediator of the platelet response at sites of laser- induced microvascular injury.

scholarly journals Efficient Degradation of Mordant Blue 9 Using the Fenton-Activated Persulfate System

Water ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 2532 ◽  
Author(s):  
Md. Nahid Pervez ◽  
Felix Y. Telegin ◽  
Yingjie Cai ◽  
Dongsheng Xia ◽  
Tiziano Zarra ◽  
...  
Keyword(s):  
Butyl Alcohol ◽  
Textile Dye ◽  
Oh Radicals ◽  
Operational Parameters ◽  
Reaction Conditions ◽  
Tert Butyl Alcohol ◽  
Initial Ph ◽  
Fe Complex ◽  
Optimal Reaction ◽  
Activated Persulfate

In this study, a Fenton-activated persulfate (Fe2+/PS) system was introduced for the efficient degradation of Mordant Blue 9 (MB 9) as a textile dye in an aqueous solution. Results showed that the degradation of MB 9 was markedly influenced by operational parameters, such as initial pH, PS concentration, Fe2+ concentration, and initial dye concentration. Optimal reaction conditions were then determined. Inorganic anions, such as Cl− and HCO3−, enhanced the degradation efficiency of MB 9 under optimal conditions. Addition of HCO3− reduced the degradation performance of MB 9, whereas the addition of Cl− increased the degradation percentage of MB 9. In addition, quenching experiments were conducted using methanol and tert-butyl alcohol as scavengers, and methanol was identified as an effective scavenger. Thus, the degradation of MB 9 was attributed to S O 4 • − and •OH radicals. The degradation and mineralization efficiency of MB 9 was significantly reduced using the conventional Fenton process i.e., Fe2+/ hydrogen peroxide (HP) because of the formation of a Fe complex during degradation. Meanwhile, the Fe2+/persulfate (PS) system improved the degradation and mineralization performance.

scholarly journals Efficient Sequestration of Hexavalent Chromium by Graphene-Based Nanoscale Zero-Valent Iron Composite Coupled with Ultrasonic Pretreatment

2021 ◽  
Vol 18 (11) ◽  
pp. 5921
Author(s):  
Haiyan Song ◽  
Wei Liu ◽  
Fansheng Meng ◽  
Qi Yang ◽  
Niandong Guo
Keyword(s):  
Aqueous Solution ◽  
Removal Efficiency ◽  
Inhibitory Effect ◽  
Ultrasonic Cavitation ◽  
Zero Valent Iron ◽  
Ultrasonic Pretreatment ◽  
Nanoscale Zero Valent Iron ◽  
Passivation Layers ◽  
Initial Ph ◽  
Two Phases

Nanoscale zero-valent iron (nZVI) has attracted considerable attention for its potential to sequestrate and immobilize heavy metals such as Cr(VI) from an aqueous solution. However, nZVI can be easily oxidized and agglomerate, which strongly affects the removal efficiency. In this study, graphene-based nZVI (nZVI/rGO) composites coupled with ultrasonic (US) pretreatment were studied to solve the above problems and conduct the experiments of Cr(VI) removal from an aqueous solution. SEM-EDS, BET, XRD, and XPS were performed to analyze the morphology and structures of the composites. The findings showed that the removal efficiency of Cr(VI) in 30 min was increased from 45.84% on nZVI to 78.01% on nZVI/rGO and the removal process performed coupled with ultrasonic pretreatment could greatly shorten the reaction time to 15 min. Influencing factors such as the initial pH, temperature, initial Cr(VI) concentration, and co-existing anions were studied. The results showed that the initial pH was a principal factor. The presence of HPO42−, NO3−, and Cl− had a strong inhibitory effect on this process, while the presence of SO42− promoted the reactivity of nZVI/rGO. Combined with the above results, the process of Cr(VI) removal in US-nZVI/rGO system consisted of two phases: (1) The initial stage is dominated by solution reaction. Cr(VI) was reduced in the solution by Fe2+ caused by ultrasonic cavitation. (2) In the following processes, adsorption, reduction, and coprecipitation coexisted. The addition of rGO enhanced electron transportability weakened the influence of passivation layers and improved the dispersion of nZVI particles. Ultrasonic cavitation caused pores and corrosion at the passivation layers and fresh Fe0 core was exposed, which improved the reactivity of the composites.

scholarly journals Polyphenol Profiling of Chestnut Pericarp, Integument and Curing Water Extracts to Qualify These Food By-Products as a Source of Antioxidants

Molecules ◽  
2021 ◽  
Vol 26 (8) ◽  
pp. 2335
Author(s):  
Gabriella Pinto ◽  
Sabrina De Pascale ◽  
Maria Aponte ◽  
Andrea Scaloni ◽  
Francesco Addeo ◽  
...  
Keyword(s):  
Mass Spectrometry ◽  
Negative Impact ◽  
Tap Water ◽  
Time Of Flight ◽  
The Other ◽  
Curing Process ◽  
Flight Mass Spectrometry ◽  
Water Curing ◽  
The Impact ◽  
By Products

Plant polyphenols have beneficial antioxidant effects on human health; practices aimed at preserving their content in foods and/or reusing food by-products are encouraged. The impact of the traditional practice of the water curing procedure of chestnuts, which prevents insect/mould damage during storage, was studied to assess the release of polyphenols from the fruit. Metabolites extracted from pericarp and integument tissues or released in the medium from the water curing process were analyzed by matrix-assisted laser desorption ionization-time of flight-mass spectrometry (MALDI-TOF-MS) and electrospray-quadrupole-time of flight-mass spectrometry (ESI-qTOF-MS). This identified: (i) condensed and hydrolyzable tannins made of (epi)catechin (procyanidins) and acid ellagic units in pericarp tissues; (ii) polyphenols made of gallocatechin and catechin units condensed with gallate (prodelphinidins) in integument counterparts; (iii) metabolites resembling those reported above in the wastewater from the chestnut curing process. Comparative experiments were also performed on aqueous media recovered from fruits treated with processes involving: (i) tap water; (ii) tap water containing an antifungal Lb. pentosus strain; (iii) wastewater from a previous curing treatment. These analyses indicated that the former treatment determines a 6–7-fold higher release of polyphenols in the curing water with respect to the other ones. This event has a negative impact on the luster of treated fruits but qualifies the corresponding wastes as a source of antioxidants. Such a phenomenon does not occur in wastewater from the other curing processes, where the release of polyphenols was reduced, thus preserving the chestnut’s appearance. Polyphenol profiling measurements demonstrated that bacterial presence in water hampered the release of pericarp metabolites. This study provides a rationale to traditional processing practices on fruit appearance and qualifies the corresponding wastes as a source of bioactive compounds for other nutraceutical applications.

scholarly journals Ti/RuO2-IrO2-SnO2 Anode for Electrochemical Degradation of Pollutants in Pharmaceutical Wastewater: Optimization and Degradation Performances

2020 ◽  
Vol 13 (1) ◽  
pp. 126
Author(s):  
Guozhen Zhang ◽  
Xingxing Huang ◽  
Jinye Ma ◽  
Fuping Wu ◽  
Tianhong Zhou
Keyword(s):  
Removal Rate ◽  
Inorganic Compounds ◽  
Oxide Coating ◽  
X Ray Diffraction ◽  
Pharmaceutical Wastewater ◽  
High Concentration ◽  
Dimensionally Stable Anodes ◽  
X Ray ◽  
Initial Ph ◽  
Cod Removal Rate

Electrochemical oxidation technology is an effective technique to treat high-concentration wastewater, which can directly oxidize refractory pollutants into simple inorganic compounds such as H2O and CO2. In this work, two-dimensionally stable anodes, Ti/RuO2-IrO2-SnO2, have been developed in order to degrade organic pollutants from pharmaceutical wastewater. Characterization by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD) showed that the oxide coating was successfully fabricated on the Ti plate surface. Electrocatalytic oxidation conditions of high concentration pharmaceutical wastewater was discussed and optimized, and the best results showed that the COD removal rate was 95.92% with the energy consumption was 58.09 kW·h/kgCOD under the electrode distance of 3 cm, current density of 8 mA/cm2, initial pH of 2, and air flow of 18 L/min.

Photodegradation of aqueous methyl orange on MnTiO3 powder at different initial pH

2010 ◽  
Vol 36 (9) ◽  
pp. 995-1001 ◽  
Author(s):  
H. Y. He ◽  
W. X. Dong ◽  
G. H. Zhang
Keyword(s):  
Methyl Orange ◽  
Initial Ph
Sign in / Sign up

Export Citation Format

Share Document