scholarly journals Mechanical and Structural Properties of Nanocarbon Particles Reinforced in Plasticised Polylactic Acid for High Strength Application

2021 ◽  
Vol 32 (2) ◽  
pp. 41-56
Author(s):  
Ajidasile Segun ◽  
Benjamin Omotayo Adewuyi ◽  
Daramola Oluyemi Ojo ◽  
Olaiya Niyi Gideon
Keyword(s):  
Diesel Engine ◽  
Mechanical Strength ◽  
Polylactic Acid ◽  
High Strength ◽  
Optical Microscope ◽  
Industrial Applications ◽  
Spare Parts ◽  
Morphological Properties ◽  
Compression Moulding ◽  
Engine Combustion

High strength application of biopolymers requires good mechanical strength. The tensile properties of polylactic acid (PLA) are relatively low for major industrial applications such as packaging, biomedical and automobile spare parts. In this study, the mechanical strength of polylactic acid was enhanced with nanocarbon isolated from diesel engine combustion soot. The isolated nanocarbon was characterised using spectrometry and Fourier transform infrared (FTIR) spectroscopy analysis. After that, the nanocarbon was used as a reinforcement in plasticised PLA to produce a composite. The PLA-nanocarbon composite was produced using the compression moulding technique. The nanocarbon composition was varied between 2 wt% and 8 wt% in the PLA matrix. The tensile, hardness and morphological properties of the composite were analysed with the tensile test, hardness test, optical microscope and X-ray diffraction (XRD) analysis. The ultraviolet (UV) spectrometer and FTIR analysis results confirmed the successful isolation of nanocarbon from the diesel engine combustion soot. The tensile and hardness properties of the PLA matrix increased with addition of nanocarbon. The morphological images showed good miscibility between the PLA and the nanocarbon reinforcement, responsible for the increase in mechanical properties. The potential use of the composite for high strength application showed great possibility based on the result obtained.

scholarly journals High-strength and fibrous capsule–resistant zwitterionic elastomers

2021 ◽  
Vol 7 (1) ◽  
pp. eabc5442
Author(s):  
Dianyu Dong ◽  
Caroline Tsao ◽  
Hsiang-Chieh Hung ◽  
Fanglian Yao ◽  
Chenjue Tang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Strength ◽  
High Strength ◽  
Design Principles ◽  
Fibrous Capsule ◽  
High Mechanical Strength ◽  
Capsule Formation ◽  
Locking Mechanism ◽  
Fibrous Capsule Formation

The high mechanical strength and long-term resistance to the fibrous capsule formation are two major challenges for implantable materials. Unfortunately, these two distinct properties do not come together and instead compromise each other. Here, we report a unique class of materials by integrating two weak zwitterionic hydrogels into an elastomer-like high-strength pure zwitterionic hydrogel via a “swelling” and “locking” mechanism. These zwitterionic-elastomeric-networked (ZEN) hydrogels are further shown to efficaciously resist the fibrous capsule formation upon implantation in mice for up to 1 year. Such materials with both high mechanical properties and long-term fibrous capsule resistance have never been achieved before. This work not only demonstrates a class of durable and fibrous capsule–resistant materials but also provides design principles for zwitterionic elastomeric hydrogels.

scholarly journals Are We Able to Print Components as Strong as Injection Molded?—Comparing the Properties of 3D Printed and Injection Molded Components Made from ABS Thermoplastic

2021 ◽  
Vol 11 (15) ◽  
pp. 6946
Author(s):  
Bartłomiej Podsiadły ◽  
Andrzej Skalski ◽  
Wiktor Rozpiórski ◽  
Marcin Słoma
Keyword(s):  
Tensile Strength ◽  
Injection Molding ◽  
Mechanical Strength ◽  
Cross Section ◽  
Fused Deposition Modeling ◽  
High Strength ◽  
Large Cross Section ◽  
Fused Deposition ◽  
Injection Molded ◽  
The Cross

In this paper, we are focusing on comparing results obtained for polymer elements manufactured with injection molding and additive manufacturing techniques. The analysis was performed for fused deposition modeling (FDM) and single screw injection molding with regards to the standards used in thermoplastics processing technology. We argue that the cross-section structure of the sample obtained via FDM is the key factor in the fabrication of high-strength components and that the dimensions of the samples have a strong influence on the mechanical properties. Large cross-section samples, 4 × 10 mm2, with three perimeter layers and 50% infill, have lower mechanical strength than injection molded reference samples—less than 60% of the strength. However, if we reduce the cross-section dimensions down to 2 × 4 mm2, the samples will be more durable, reaching up to 110% of the tensile strength observed for the injection molded samples. In the case of large cross-section samples, strength increases with the number of contour layers, leading to an increase of up to 97% of the tensile strength value for 11 perimeter layer samples. The mechanical strength of the printed components can also be improved by using lower values of the thickness of the deposited layers.

scholarly journals Evaluation of the influence of design in the mechanical properties of honeycomb cores used in composite panels

2021 ◽  
pp. 146442072098519
Author(s):  
A Miranda ◽  
M Leite ◽  
L Reis ◽  
E Copin ◽  
MF Vaz ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Failure Modes ◽  
Industrial Applications ◽  
Sandwich Composite ◽  
Composite Panels ◽  
Distribution Analysis ◽  
Absorbed Energy ◽  
Fused Filament Fabrication ◽  
Subtractive Manufacturing

The aerospace, automotive, and marine industries are heavily reliant on sandwich panels with cellular material cores. Although honeycombs with hexagonal cells are the most commonly used geometries as cores, recently there have been new alternatives in the design of lightweight structures. The present work aims to evaluate the mechanical properties of metallic and polymeric honeycomb structures, with configurations recently proposed and different in-plane orientations, produced by additive and subtractive manufacturing processes. Structures with configurations such as regular hexagonal honeycomb (Hr), lotus (Lt), and hexagonal honeycomb with Plateau borders (Pt), with 0°, 45°, and 90° orientations were analyzed. To evaluate its properties, three-point bending tests were performed, both experimentally and by numerical modeling, by means of the finite element method. Honeycombs of two aluminum alloys and polylactic acid were fabricated. The structures produced in aluminum were obtained either by selective laser melting technology or by machining, while polylactic acid structures were obtained by material extrusion using fused filament fabrication. From the stress distribution analysis and the load–displacement curves, it was possible to evaluate the strength, stiffness, and absorbed energy of the structures. Failure modes were also analyzed for polylactic acid honeycombs. In general, a strong correlation was observed between numerical and experimental results. The results show that the stiffness and absorbed energy increase in the order, Hr, Pt, Lt, and with the orientation through the sequence, 45°, 90°, 0°. Thus, Lt structures with 0° orientation seem to be good alternatives to the traditional honeycombs used in sandwich composite panels for those industrial applications where low weight, high stiffness, and large energy-absorbing capacity are required.

An Experimental Study of Cavity Nucleation During Superplastic Deformation

1990 ◽  
Vol 196 ◽  
Author(s):  
Jiang Xinggang ◽  
Cui Jianzhong ◽  
Ma Longxiang
Keyword(s):  
Grain Boundary ◽  
Superplastic Deformation ◽  
Thermomechanical Processing ◽  
High Stress ◽  
High Strength ◽  
Optical Microscope ◽  
Grain Boundary Sliding ◽  
Cavity Nucleation ◽  
High Stress Concentration ◽  
Voltage Electron

ABSTRACTCavity nucleation during superplastic deformation of a high strength aluminium alloy has been studied using a high voltage electron microscope and an optical microscope. The results show that cavities nucleation is due only to superplastic deformation and not to pre-existing microvoids which may be introduced during thermomechanical processing. The main reason for cavity nucleation is the high stress concentration at discontinuties in the plane of the grain boundary due to grain boundary sliding.

Effects of water introduction on diesel engine combustion and emissions

1977 ◽  
Vol 16 (1) ◽  
pp. 321-336 ◽  
Author(s):  
G. Greeves ◽  
I.M. Khan ◽  
G. Onion
Keyword(s):  
Diesel Engine ◽  
Engine Combustion

FEM Analysis and Experimental Study for Bond Strength of High-Strength Coating by Wedged Load Test Method

2010 ◽  
Vol 152-153 ◽  
pp. 1058-1061
Author(s):  
Zhou Wei ◽  
Xiao Xia Zhang
Keyword(s):  
Bond Strength ◽  
Adhesion Strength ◽  
Fem Analysis ◽  
High Strength ◽  
Pressure Head ◽  
Optical Microscope ◽  
Complex Stress ◽  
Complex Stress State ◽  
Load Test ◽  
Test Method

A wedged load test method is used to evaluate the adhesion strength of high-strength coatings, which have been processed with various sintering parameters. In this test, for stress concentration at cut tip, cracks are always induced and expanded rapidly cross the interface between coating and substrate. Macro-fracture and SEM image of coating interface of high-strength coating are characterized using optical microscope and scanning electron microscopy (SEM), respectively. In order to evaluate the bonding properties between coating and substrate effectively, corresponding finite element (FE) analysis has been conducted to evaluate the adhesion strength of high-strength coating. And stress distributions cross the interface of high-strength coating are obtained. The stress analysis can help to evaluate the bond strength of high-strength coating. Because of small specimen and contact relationship between wedged pressure head and wedged cuts, complex stress state is affected by many factors resulting from interface, and also by the thickness of coating.

Sign in / Sign up

Export Citation Format

Share Document