Performance Analysis of 6T SRAM and ONOFIC Cells

2021 ◽  
Vol 13 ◽  
Author(s):  
Vijay Kumar Sharma ◽  
Masood Ahmad Malik
Keyword(s):  
Low Power ◽  
Leakage Current ◽  
Performance Metrics ◽  
Random Access ◽  
Memory Cell ◽  
Critical Issue ◽  
Performance Comparison ◽  
Technology Node ◽  
Noise Margin ◽  
Sram Cell

Background: As the Technology node scales down to deep sub-micron regime, the design of static random-access memory (SRAM) cell becomes a critical issue because of increased leakage current components. These leakage current components prevent to design a low power processor as large of the processor power is consumed by the memory part. Objective: In this paper, a SRAM cell is designed based on ON/OFF logic (ONOFIC) approach. Static noise margin (SNM) of the cell for the different states are calculated and evaluated by using butterfly as well as noise (N) curves with the help of Cadence tools at 45 nm technology node. Methods: ONOFIC approach helps to reduce the leakage current components which makes a low power memory cell. A performance comparison is made between the conventional six-transistor (6T) SRAM cell and memory cell using ONOFIC approach. Results: Low value of power delay product (PDP) is the outcome of ONOFIC approach as compared to conventional cell. ONOFIC approach decreases PDP by 99.99% in case of hold state. Conclusions: ONOFIC approach improves the different performance metrics for the different states of the SRAM cell.

Analysis of 6T SRAM Cell in Different Technologies

2017 ◽  
Vol MCSP2017 (01) ◽  
pp. 7-10 ◽  
Author(s):  
Subhashree Rath ◽  
Siba Kumar Panda
Keyword(s):  
Low Power ◽  
Data Storage ◽  
Low Voltage ◽  
Random Access ◽  
Storage Device ◽  
Cmos Process ◽  
Process Technology ◽  
Digital Devices ◽  
Noise Margin ◽  
Sram Cell

Static random access memory (SRAM) is an important component of embedded cache memory of handheld digital devices. SRAM has become major data storage device due to its large storage density and less time to access. Exponential growth of low power digital devices has raised the demand of low voltage low power SRAM. This paper presents design and implementation of 6T SRAM cell in 180 nm, 90 nm and 45 nm standard CMOS process technology. The simulation has been done in Cadence Virtuoso environment. The performance analysis of SRAM cell has been evaluated in terms of delay, power and static noise margin (SNM).

Design of a Stable Low Power 11-T Static Random Access Memory Cell

2020 ◽  
Vol 29 (13) ◽  
pp. 2050206 ◽  
Author(s):  
Ashish Sachdeva ◽  
V. K. Tomar
Keyword(s):  
Random Access ◽  
Memory Cell ◽  
Random Access Memory ◽  
Static Random Access Memory ◽  
Signal To Noise ◽  
Access Memory ◽  
Noise Margin ◽  
Sram Cell ◽  
Variation Tolerance ◽  
Read Signal

In this paper, a 11-T static random-access memory (SRAM) cell has been examined that shows a fair reduction in read power dissipation while upholding the stability and moderate performance. In the presented work, parametric variability analysis of various design metrices such as signal to noise margin, read current and read power of the Proposed 11T cell are presented and compared with few considered topologies. The Proposed cell offers single ended write operation and differential read operation. The improvement in read signal to noise margin and write signal to noise margin with respect to conventional 6T SRAM is 10.63% and 33.09%, respectively even when the write operation is single ended. Mean hold static noise margin of the cell for 3000 samples is [Formula: see text] times higher than considered D2p11T cell. Sensitivity analysis of data retention voltage (DRV) with respect to temperature variations is also investigated and compared with considered topologies. DRV variation with temperature is least in FF process corner. In comparison to conventional 6T SRAM cell, the write and read delay of Proposed 11T cell gets improved by [Formula: see text] and 1.64%, respectively. Proposed 11T topology consumes least read energy in comparison with considered topologies. In comparison with another considered 11T topology, i.e., D2p11T cell, Proposed cell consumes 13.11% lesser area. Process variation tolerance with Monte Carlo simulation for read current and read power has been investigated using Cadence virtuoso tool with GPDK 45-nm technology.

scholarly journals VARIABILITY ANALYSIS OF 6T AND 7T SRAM CELL IN SUB-45NM TECHNOLOGY

2011 ◽  
Vol 12 (1) ◽  
pp. 13-30 ◽  
Author(s):  
Aminul Islam ◽  
Mohd. Hasan
Keyword(s):  
Random Access ◽  
Memory Cell ◽  
Static Random Access Memory ◽  
Access Time ◽  
Access Memory ◽  
Static Noise Margin ◽  
Noise Margin ◽  
Sram Cell ◽  
Pvt Variations ◽  
Static Noise

This paper analyses standard 6T and 7T SRAM (static random access memory) cell in light of process, voltage and temperature (PVT) variations to verify their functionality and robustness. The 7T SRAM cell consumes higher hold power due to its extra cell area required for its functionality constraint. It shows 60% improvement in static noise margin (SNM), 71.4% improvement in read static noise margin (RSNM) and 50% improvement in write static noise margin (WSNM). The 6T cell outperforms 7T cell in terms of read access time (TRA) by 13.1%. The write access time (TWA) of 7T cell for writing "1" is 16.6 x longer than that of 6T cell. The 6T cell proves it robustness against PVT variations by exhibiting narrower spread in TRA (by 1.2 x) and Twa (by 3.4x). The 7T cell offers 65.6% saving in read power (RPWR) and 89% saving in write power (WPWR). The RPWR variability indicates that 6T ell is more robust against process variation by 3.9x. The 7T cell shows 1.3x wider write power (WPWR) variability indicating 6T cell's robustness against PVT variations. All the results are based on HSPICE simulation using 32 nm CMOS Berkeley Predictive Technology Model (BPTM).

scholarly journals A Novel concept on 8-Transistor Dynamic Feedback Control on Static RAM Cell Array

2018 ◽  
Vol 7 (2.20) ◽  
pp. 109
Author(s):  
S Renukarani ◽  
Bhavana Godavarthi ◽  
SK Bia Roshini ◽  
Mohammad Khadir
Keyword(s):  
Dynamic Control ◽  
Random Access ◽  
Memory Cell ◽  
Dynamic Feedback ◽  
Cell Array ◽  
Static Noise Margin ◽  
Noise Margin ◽  
Sram Cell ◽  
Static Ram ◽  
Static Noise

A novel idea of 8-Transistor (8T) static random access memory cell with enhanced information stability, sub threshold operation may be outlined. Those prescribed novel built single-ended for dynamic control 8 transistors static RAM (SRAM) cell enhances the static noise margin (SNM) to grater low energy supply. The suggested 8T takes less read and write power supply compared to 6T. Those suggested 8T need higher static noise margin than that from 6T. The portable microprocessor chips need ultralow energy consuming circuits on use battery to more drawn out span. The power utilization might be minimized utilizing non-conventional gadget structures, new circuit topologies, and upgrading the architecture. Although, voltage scaling require of the operation completed over sub threshold for low power consumption, and there will be an inconvenience from exponential decrease in execution. However, to sub threshold regime, that data stability of SRAM cell might a chance to be a amazing issue and worsens for those scaling from claming MOSFET ought to sub-nanometer engineering technology.  

DG-FINFET-BASED SRAM CONFIGURATIONS FOR INCREASED SEU IMMUNITY

2012 ◽  
Vol 21 (04) ◽  
pp. 1250032 ◽  
Author(s):  
S. S. RATHOD ◽  
A. K. SAXENA ◽  
S. DASGUPTA
Keyword(s):  
Performance Metrics ◽  
Random Access ◽  
Oxide Thickness ◽  
Normal Operation ◽  
Thickness Variation ◽  
Back Gate ◽  
Single Event Upsets ◽  
Noise Margin ◽  
Sram Cell ◽  
Power Delay Product

In this paper, we propose a new circuit level hardening techniques that can decrease the sensitivity of Static Random Access Memory (SRAM) cells to radiation induced Single Event Upsets (SEUs). Five different types of 32 nm double gate (DG)-FinFET-based SRAM cells are analyzed. Proposed SRAM cell outperforms over the unhardened SRAM when exposed to radiation. This is primarily due to the modification of the source potential used to reduce the effect of SEU without affecting normal operation. Static Noise Margin (SNM), Read Noise Margin (RNM), Write Noise Margin (WNM) and Power Delay Product (PDP) are the performance metrics computed for each type of SRAM cell. Effect of back gate voltage and back gate oxide thickness variation on device characteristic show detrimental effects on radiation hardened capabilities of a device. Benchmarking is done against DICE latch and it is found that as compared to DICE latch proposed DG-FinFET SRAM has low transistor count, less area, low recovery time and fault tolerance to internal as well as external nodes.

scholarly journals Performance comparison of SRAM cells in 45NM technology in the presence of a memory cell control circuit

2018 ◽  
Vol 7 (4.5) ◽  
pp. 645
Author(s):  
Sanket Jagadale ◽  
Aniket Phapale ◽  
T. V. Sai Varun Sasthry ◽  
V. S. Kanchana Bhaaskaran
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Memory Cell ◽  
Performance Comparison ◽  
Control Circuit ◽  
Stable Operation ◽  
Memory Retention ◽  
Cell Control ◽  
Noise Margin ◽  
Sram Design

Lowering power consumption and increasing the noise margin have become the two most important aspects to be considered in SRAM design. Additionally, a stable operation with good memory retention capability has gained greater importance in obtaining good yield at low-voltage and low-power SRAM designs, due to the fact that parameter variations play a major role in scaled technologies. In this paper, the 6T SRAM, 7T low power SRAM and 7T multi threshold low power SRAM designs are designed, to incorporate power gating technique. The architecture of each of the SRAM designs and their working are analyzed thoroughly. The outputs of the read, write and hold operations with transient response are observed and the power dissipation and static noise margin (SNM) of the each of the SRAM cells is calculated and compared. The paper also presents new power reduction solution through the cell control circuit which reduces the unwanted and spurious switching activities during read and writes operations. The paper demonstrates the reduction of the power con- sumption through the use of cell control circuit.   

A loadless 4T SRAM powered by gate leakage current with a high tolerance for fluctuations in device parameters

2021 ◽  
Author(s):  
Yihan Zhu ◽  
Takashi Ohsawa
Keyword(s):  
Random Access ◽  
Memory Cell ◽  
Gate Insulator ◽  
Gate Leakage ◽  
Static Noise Margin ◽  
Noise Margin ◽  
Sram Cell ◽  
Conventional Cell ◽  
P Type ◽  
Static Noise

Abstract A novel loadless four-transistor static random access memory cell is proposed that consists of two N-type driver MOSFETs and two P-type access ones whose gate leakage currents from word-line are used for holding data in the cell. It is shown that the proposed cell has a higher tolerance for manufacturing device fluctuations compared with the conventional loadless 4T SRAM. Furthermore, it is free from bit-line disturb in contrast to the conventional cell. It is confirmed by simulation in 32nm technology node that the read static noise margin of the proposed cell reaches 138.7% of the six-transistor SRAM cell and that the hold static noise margin can be acceptable when the gate insulator thickness of the P-type access MOSFETs is made thinner than the N-type driver MOSFETs. The retention current for the proposed cell decreases to 66.7% of the 6TSRAM and the data rate in read increases to 125%.

Low Power Restoration Circuits Reduce Swing Voltages of SRAM Cell With Improved Read and Write Margins

2021 ◽  
Vol 13 (2) ◽  
pp. 16-28
Author(s):  
Vinod Kumar ◽  
Ram Murti Rawat
Keyword(s):  
Comparative Analysis ◽  
Low Power ◽  
Random Access ◽  
Noise Margin ◽  
Sram Cell ◽  
Static Random Access Memories ◽  
Power Restoration ◽  
Node Voltage ◽  
Static Noise ◽  
Better Than

This paper examines the factors that affect the static noise margin (SNM) of static random access memories which focus on optimizing read and write operation of 8T SRAM cell which is better than 6T SRAM cell using swing restoration for dual node voltage. New 8T SRAM technique on the circuit or architecture level is required. In this paper, comparative analysis of 6T and 8T SRAM cells with improved read and write margin is done for 130nm technology with cadence virtuoso schematics tool.

scholarly journals A Low Power 6T-Auto Awake Mode-SRAM Design for high speed storage application

2019 ◽  
Vol 8 (9) ◽  
pp. 204-208
Keyword(s):  
Low Power ◽  
High Speed ◽  
Random Access ◽  
Digital World ◽  
Noise Margin ◽  
Sram Cell ◽  
Sram Design ◽  
Static Ram ◽  
Power Application ◽  
Reduced Power Consumption

In the digital world, Static Random Access Memory (SRAM) is one of the efficient core component for electronics design, it consumes huge amount of power and die area. In this research, the SRAM design analysis in terms of read margin, write margin and Static Noise Margin (SNM) for low power application is considered. In SRAM memory, both read and write operation affect by noise margin. So, read and write noise margins are considered as the significant challenges in designing SRAM cell. In this research, robust 6T-SRAM cell is designed to decrease the power utilization. The Auto Awake Mode is developed to control the entire 6T-SRAM cell design. The proposed 6T-SRAM- Auto Awake Mode (6T-SRAM-AAM) was implemented to reduce power utilization of understand and write down operation inside the 20 nm FinFET library. The experimental results showed the proposed 6T-SRAM-AAM design reduced power consumption of read & write operation up to 25% to 33.33% compared to existing Static RAM cells design

Design of Low Power Half Select Free 10T Static Random-Access Memory Cell

2020 ◽  
pp. 2150073 ◽  
Author(s):  
Ashish Sachdeva ◽  
V. K. Tomar
Keyword(s):  
Random Access ◽  
Memory Cell ◽  
Random Access Memory ◽  
Static Random Access Memory ◽  
Access Time ◽  
Signal To Noise ◽  
Access Memory ◽  
Noise Margin ◽  
Sram Cell ◽  
Power Delay Product

This paper presents a circuit-level technique of designing a low power and half select free 10T Static Random-Access Memory Cell (SRAM). The proposed cell works with single end read operation and differential write operation. The proposed bit-cell is free from half select issue and supports bit interleaving format. The presented 10T cell exhibits 40.75% lower read power consumption in comparison to conventional 6T SRAM cell, attributed to reduction of activity factor during read operation. The loop cutting transistors used in core latch improve write signal-to-noise margin (WSNM) by 14.94% and read decoupled structure improve read signal-to-noise margin (RSNM) by [Formula: see text] as compared to conventional 6T SRAM. In the proposed work, variability analysis of significant design parameters such as read current, stand-by SNM, and read power of the projected 10T SRAM cell is presented and compared with considered topologies. Mean value of hold static noise margin of the cell for 3000 samples is [Formula: see text] times higher than the considered D2p11T cell. The proposed 10T cell shows [Formula: see text] and [Formula: see text] narrower read access time and write access time, respectively, as compared to conventional 6T SRAM cell. Read current to bit-line leakage current ratio of the proposed 10T cell has been investigated and is improved by [Formula: see text] as compared to conventional 6T SRAM cell. The write power delay product and read power delay product of the proposed 10T cell are [Formula: see text] and [Formula: see text] lower than conventional 6T SRAM cell. In this work, cadence virtuoso tool with Generic Process Design Kit (GPDK) 45[Formula: see text]nm technology file has been utilized to carry out simulations.

Sign in / Sign up

Export Citation Format

Share Document