scholarly journals Optimization of Arsenic Adsorption onto Cativated Carbon Dreived from Potato Peel Using Response Surfase Methodology

2019 ◽  
Vol 7 (2) ◽  
Author(s):  
Akram A. Haji ◽  
Nidhal M.Sh. Mohammed
Keyword(s):  
Activated Carbon ◽  
Central Composite Design ◽  
Adsorption Capacity ◽  
Chemical Activation ◽  
Arsenic Concentration ◽  
Interactive Effects ◽  
Quadratic Model ◽  
Maximum Adsorption Capacity ◽  
Potato Peel ◽  
Central Composite

The present study was designed to optimizing the adsorption of As (V) onto potato peel derived activated carbon (MPP-AC) by employing response surface method and central composite design. Adsorbent of cheap and locally available potato residue was produced based on chemical activation with H3PO4 subsequently carbonization to produce the porous activated carbon. The individual and interactive effects of five variables including initial arsenic concentration, temperature, time, dosage amount and pH of the medium were investigated. Based on the statistic analysis (ANOVA), the quadratic model was developed associating the adsorption capacity (qe). The optimum conditions were obtained of 9.98 mg L-1 of initial As (V) concentration, 28 °C of temperature, 39.7 min of time, 0.97 g of adsorbent dose and 7.3 of pH. The maximum adsorption capacity was 0.27 mg g-1 and 76.5% removal efficiency. The equilibrium isotherms and kinetic studies for estimating the mechanism of process demonstrated a good fit to Langmuir model and the pseudo-second order, respectively. The results of this study showed that the feasibility of central composite design for control adsorption process and indicated the use of activated carbon of potato residue have important implications for As (V) removal.

scholarly journals Removal of Anionic and Cationic Dyes from Wastewater Using Activated Carbon from Palm Tree Fiber Waste

Processes ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 416
Author(s):  
Basma G. Alhogbi ◽  
Shoruq Altayeb ◽  
Effat. A. Bahaidarah ◽  
Mahmoud F. Zawrah
Keyword(s):  
Electron Microscopy ◽  
Activated Carbon ◽  
Adsorption Isotherm ◽  
Adsorption Capacity ◽  
Chemical Activation ◽  
High Yield ◽  
Maximum Adsorption Capacity ◽  
Palm Tree ◽  
Fast Method ◽  
Adsorbent Dosage

This study focuses on using a facile method for the green preparation of activated carbon (AC) from palm tree fiber (PTF) waste. The synthesized cost-effective AC was investigated for the removal of an anionic dye (Congo red, CR) and a cationic dye (Rhodamine B, RhB) from wastewater. The morphological and structural characterization of the synthesized AC were performed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), surface area, Fourier transform infrared spectroscopy (FTIR), total pore volume, average pore diameter and pore size distribution, zeta potential, and zero-point charge. To investigate the adsorption efficiency, different parameters such as adsorbent dosage, solution pH, initial dye concentration, and duration were applied using the batch experiments. Various adsorption isotherm and kinetics models were applied to study the adsorption mechanism and dynamics. The results showed that chemical activation with a weak acid (H3PO4) at 400 °C for 30 min is a fast method for the activation of each precursor and produces a high yield. The result of analysis showed an increase in the adsorption capacity at pH 2. The maximum adsorption capacity was 9.79 and 26.58 mg g−1 at 30 min for CR dye and RhB dye, respectively. The optimum adsorbent dosage for the activated carbon from palm tree fiber (PTFAC) was 0.15 g with a high percentage removal of CR (98.24%) and RhB (99.86%) dyes. The adsorption isotherm and kinetic studies were found to be favorable and feasible for assessing the adsorption of dyes with the Langmuir model and pseudo-second-order reaction, respectively. In addition, the AC showed reusability up to five cycles. The results showed that the synthesized AC was environmentally friendly and successfully removed dyes from wastewater.

scholarly journals Adsorption of methylene blue onto betel nut husk-based activated carbon prepared by sodium hydroxide activation process

2020 ◽  
Vol 82 (9) ◽  
pp. 1932-1949
Author(s):  
Mondira Bardhan ◽  
Tamanna Mamun Novera ◽  
Mumtahina Tabassum ◽  
Md. Azharul Islam ◽  
Ali H. Jawad ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Chemical Activation ◽  
Maximum Adsorption Capacity ◽  
Activation Process ◽  
Order Kinetic ◽  
Betel Nut ◽  
Non Linear ◽  
Mb Adsorption

Abstract In this study, activated carbon (AC) was prepared from agro-waste betel nut husks (BNH) through the chemical activation method. Different characterization techniques described the physicochemical nature of betel nut husks activated carbon (BNH-AC) through Fourier transform infrared spectroscopy (FTIR), Brunauer–Emmett–Teller (BET), scanning electron microscopy (SEM), and pH point of zero charge. Later, the produced AC was used for methylene blue (MB) adsorption via numerous batch experimental parameters: initial concentrations of MB dye (25–250 mg/L), contact time (0.5–24 hours) and initial pH (2–12). Dye adsorption isotherms were also assessed at three temperatures where the maximum adsorption capacity (381.6 mg/g) was found at 30 °C. The adsorption equilibrium data were best suited to the non-linear form of the Freundlich isotherm model. Additionally, non-linear pseudo-second-order kinetic model was better fitted with the experimental value as well. Steady motion of solute particles from the boundary layer to the BNH-AC's surface was the possible reaction dynamics concerning MB adsorption. Thermodynamic study revealed that the adsorption process was spontaneous and exothermic in nature. Saline water emerged as an efficient eluent for the desorption of adsorbed dye on AC. Therefore, the BNH-AC is a very promising and cost-effective adsorbent for MB dye treatment and has high adsorption capacity.

scholarly journals Application of Central Composite Design to the Photo Fenton Degradation of Methyl Orange Azo Dye Using Fe-Activated Carbon Catalyst

2020 ◽  
Vol 5 (8) ◽  
pp. 479-485
Author(s):  
Abubakar Muhammad ◽  
Ahmed Lawal Mashi
Keyword(s):  
Activated Carbon ◽  
Methyl Orange ◽  
Central Composite Design ◽  
Correlation Coefficients ◽  
Quadratic Model ◽  
Process Time ◽  
Optimum Reaction ◽  
Methyl Orange Concentration ◽  
Central Composite ◽  
Degradation Of Methyl Orange

Photo-fenton oxidation technique is one of the emerging oxidation processes explored in treatment of organic pollutants in aqueous solutions. This research is focused on utilization of Fe(II) loaded activated carbon and H2O2(aq) in a photofenton process to generate hydroxyl radicals that mineralize methyl orange dyes. Samples of activated carbon were treated with Fe(NO3)2(aq) and characterized using SEM, pHZPC, specific surface area and boehm’s titration. The degradation of methyl orange by the iron loaded activated carbon (Fe-Ac), via photo-Fenton process, was investigated in lab-scale defined by experimental design. Central composite design (CCD) was used to evaluate the effects of the five independent variables considered for the optimization of the oxidative process: time, FeAc dose, methyl orange concentration, pH and H2O2 concentrations. In the optimization, the correlation coefficients (R2 ) for the quadratic model was 0.9941. Optimum reaction conditions were obtained at pH = 3, catalyst dose = 0.1 mg/100ml, H2O2 = 0.62ml, methyl orange concentration = 5mg/l and time = 30 minutes.

Activated carbon from molasses efficiency for Cr(VI), Pb(II) and Cu(II) adsorption: A mechanistic study

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Activated Carbon ◽  
Phosphoric Acid ◽  
Sugar Industry ◽  
Chemical Activation ◽  
High Surface ◽  
High Surface Area ◽  
Mechanistic Study ◽  
Acid Mixture ◽  
Maximum Adsorption Capacity ◽  
Good Potential

Activated carbon was prepared from molasses, which are natural precursors of vegetable origin resulting from the sugar industry. A simple elaboration process, based on chemical activation with phosphoric acid, was proposed. The final product, prepared by activation of molasses/phosphoric acid mixture in air at 500°C, presented high surface area (more than 1400 m2/g) and important maximum adsorption capacity for methylene blue (625 mg/g) and iodine (1660 mg/g). The activated carbon (MP2(500)) showed a good potential for the adsorption of Cr(VI), Cu(II) and Pb(II) from aqueous solutions. The affinity for the three ions was observed in the following order Cu2+ Cr6+ Pb2+. The process is governed by monolayer adsorption following the Langmuir model, with a correlation coefficient close to unity.

Analisis Variasi Temperatur Aktivasi Terhadap Daya Serap Arang Aktif Tandan Aren (Arenga Pinnata Merr) Dengan Agen Aktivasi Potassium Silicate(K2SiO3)

2020 ◽  
Vol 5 (3) ◽  
pp. 221
Author(s):  
Muhammad Azam ◽  
Muhammad Anas ◽  
Erniwati Erniwati
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Temperature Variation ◽  
Chemical Activation ◽  
Weight Ratio ◽  
Potassium Silicate ◽  
Physical Activation ◽  
Activation Temperature ◽  
Pyrolysis Reactor

This study aims to determine the effect of variation of activation temperature of activated carbon from sugar palm bunches of chemically activatied with the activation agent of potassium silicate (K2SiO3) on the adsorption capacity of iodine and methylene blue. Activated carbon from bunches of sugar palmacquired in four steps: preparationsteps, carbonizationstepsusing the pyrolysis reactor with temperature of 300 oC - 400 oC for 8 hours and chemical activation using of potassium silicate (K2SiO3) activator in weight ratio of 2: 1 and physical activation using the electric furnace for 30 minutes with temperature variation of600 oC, 650 oC, 700 oC, 750 oC and 800 oC. The iodine and methyleneblue adsorption testedby Titrimetric method and Spectrophotometry methodrespectively. The results of the adsorption of iodine and methylene blue activated carbon from sugar palm bunches increased from 240.55 mg/g and 63.14 mg/g at a temperature of 600 oC to achieve the highest adsorption capacity of 325.80 mg/g and 73.59 mg/g at temperature of 700 oC and decreased by 257.54 mg/g and 52.03 mg/g at a temperature of 800 oCrespectively.However, it does not meet to Indonesia standard (Standard Nasional Indonesia/SNI), which is 750 mg/g and 120 mg/g respectively.

scholarly journals Synthesis and Characterisation of Pyridinium-Based Ionic Liquid as Activating Agent in Rubber Seed Shell Activated Carbon Production for CO2 Capture

2021 ◽  
Vol 82 (1) ◽  
pp. 85-95
Author(s):  
Nawwarah Mokti ◽  
Azry Borhan ◽  
Siti Nur Azella Zaine ◽  
Hayyiratul Fatimah Mohd Zaid
Keyword(s):  
Ionic Liquid ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Co2 Capture ◽  
Low Cost ◽  
Chemical Activation ◽  
Green Technology ◽  
Activation Process ◽  
Rubber Seed ◽  
Activating Agent

The use of an activating agent in chemical activation of activated carbon (AC) production is very important as it will help to open the pore structure of AC as adsorbents and could enhance its performance for adsorption capacity. In this study, a pyridinium-based ionic liquid (IL), 1-butylpyridinium bis(trifluoromethylsulfonyl) imide, [C4Py][Tf2N] has been synthesized by using anion exchange reaction and was characterized using few analyses such as 1H-NMR, 13C-NMR and FTIR. Low-cost AC was synthesized by chemical activation process in which rubber seed shell (RSS) and ionic liquid [C4Py][Tf2N] were employed as the precursor and activating agent, respectively. AC has been prepared with different IL concentration (1% and 10%) at 500°C and 800°C for 2 hours. Sample AC2 shows the highest SBET and VT which are 392.8927 m2/g and 0.2059 cm3/g respectively. The surface morphology of synthesized AC can be clearly seen through FESEM analysis. A high concentration of IL in sample AC10 contributed to blockage of pores by the IL. On the other hand, the performance of synthesized AC for CO2 adsorption capacity also studied by using static volumetric technique at 1 bar and 25°C. Sample AC2 contributed the highest CO2 uptakes which is 50.783 cm3/g. This current work shows that the use of low concentration IL as an activating agent has the potential to produce porous AC, which offers low-cost, green technology as well as promising application towards CO2 capture.

scholarly journals Pinecone-Derived Activated Carbons as an Effective Medium for Hydrogen Storage

Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2237
Author(s):  
Sara Stelitano ◽  
Giuseppe Conte ◽  
Alfonso Policicchio ◽  
Alfredo Aloise ◽  
Giovanni Desiderio ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Hydrogen Storage ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Hydrogen Adsorption ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Textural Properties ◽  
Biomass Waste ◽  
Wavelength Dispersive Spectrometry

Pinecones, a common biomass waste, has an interesting composition in terms of cellulose and lignine content that makes them excellent precursors in various activated carbon production processes. The synthesized, nanostructured, activated carbon materials show textural properties, a high specific surface area, and a large volume of micropores, which are all features that make them suitable for various applications ranging from the purification of water to energy storage. Amongst them, a very interesting application is hydrogen storage. For this purpose, activated carbon from pinecones were prepared using chemical activation with different KOH/precursor ratios, and their hydrogen adsorption capacity was evaluated at liquid nitrogen temperatures (77 K) at pressures of up to 80 bar using a Sievert’s type volumetric apparatus. Regarding the comprehensive characterization of the samples’ textural properties, the measurement of the surface area was carried out using the Brunauer–Emmett–Teller method, the chemical composition was investigated using wavelength-dispersive spectrometry, and the topography and long-range order was estimated using scanning electron microscopy and X-ray diffraction, respectively. The hydrogen adsorption properties of the activated carbon samples were measured and then fitted using the Langmuir/ Töth isotherm model to estimate the adsorption capacity at higher pressures. The results showed that chemical activation induced the formation of an optimal pore size distribution for hydrogen adsorption centered at about 0.5 nm and the proportion of micropore volume was higher than 50%, which resulted in an adsorption capacity of 5.5 wt% at 77 K and 80 bar; this was an increase of as much as 150% relative to the one predicted by the Chahine rule.

Application of Carbonaceous Materials to Phenol Removal from Aqueous Solution by Adsorption

2012 ◽  
Vol 164 ◽  
pp. 297-301 ◽  
Author(s):  
Wei Fang Dong ◽  
Li Hua Zang ◽  
Qing Chao Gong ◽  
Cun Cun Chen ◽  
Cai Hong Zheng ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Petroleum Coke ◽  
Granular Activated Carbon ◽  
Powdered Activated Carbon ◽  
Maximum Adsorption Capacity ◽  
Phenol Removal ◽  
Carbonaceous Materials ◽  
Solution Ph ◽  
Equilibrium Studies

Low cost carbonaceous materials were evaluated for their ability to remove phenol from wastewater. The effects of adsorbents dosage, contact time and maximum adsorption capacity were investigated for granular activated carbon, powdered activated carbon, petroleum coke and multi-walled carbon nanotube (MWNT). Equilibrium studies were conducted in 50mg/L initial phenol concentration, solution pH of 5 and at temperature of 23°C. The results showed the adsorption process was fast and it reached equilibrium in 3 h. Petroleum coke and MWNT had poor adsorption which could reach the removal efficiency of phenol with 43.18% and 36.64% respectively. The granular activated carbon possessed good adsorption ability to phenol with 96.40% at the optimum dosage 5g and optimum time 90min.The powdered activated carbon was an effective adsorbent with a maximum adsorption capacity of 42.32 mg/g.

Sign in / Sign up

Export Citation Format

Share Document