A Review On Rectangular Heat Sinks Under Natural Convection

2019 ◽  
Vol 118 (7) ◽  
pp. 44-49
Author(s):  
Rajshekhar V Unni ◽  
Vijay S Majali
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Ambient Temperature ◽  
Temperature Difference ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Cost Effective ◽  
Heat Sinks ◽  
Maximum Heat ◽  
Fin Spacing

In the paper review of studies of heat sinks under natural convection is taken up. The discussions are mainly on experimental works carried out on rectangular fin arrays, optimization of heat sink dimensions and heat transfer enhancement. The geometries of heat sinks, fin spacing, fin height, fin length, fin thickness and fin material and base to ambient temperature difference are the important parameters on which heat transfer rate depends. So the design and optimization of the heat sink geometries becomes essential. It was found that the optimum fin  spacing is ranging from 6.1- 11.9mm which gives maximum heat dissipation; the base to ambient temperature difference is 20-1500C. During most of the experimental work carried out a good thermal conductivity material which is cost-effective was chosen.

Enhanced Heat Transfer in Radial Heat Sinks for LED Lamps

2018 ◽  
Author(s):  
Fernando Cano-Banda ◽  
Ana Gallardo-Gutierrez ◽  
Jesus Garcia-Gonzalez ◽  
Abel Hernandez-Guerrero ◽  
Luis Luviano-Ortiz
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Heat Sinks ◽  
Output Analysis ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Longitudinal Orientation ◽  
Radial Heat

A radial design of a passive heat sink for cooling LED illumination devices is analyzed numerically in order to identify the geometric shape that promotes better heat dissipation rates. Natural convection with the surrounding is considered during the operation of the heat sink. Due to the fact that natural convection is the main mechanism of heat transfer, the shape of the heat sink has a high influence in the heat dissipated. An analysis of the influence of different parameters of a heat sink is conducted in the presented study. The radial heat sink under analysis consists in a flat disc with rectangular fins on it, and the fins are distributed with a radial longitudinal orientation in a circular row arrangement. The number of rows can vary but there is a constant relation of two times the number of fins between the number of fins in an inner row and the next outer row. In order to find a correct configuration to improve the dissipation of heat, parameters like the number of fins, the length of the fins and the separation between fins are studied. The average Nusselt number and thermal resistance for each geometric configuration are compared. The output analysis provides the best shape for a maximum heat transfer.

Natural Convection From Finned Heat Sinks

2007 ◽  
Author(s):  
L. T. Yeh ◽  
Joseph Yeh ◽  
B. T. F. Chung
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Sink ◽  
Plate Thickness ◽  
Heat Sinks ◽  
Cfd Model ◽  
Practical Applications ◽  
Computational Fluid Dynamics Analysis ◽  
Fin Spacing ◽  
Fin Length

A CFD (computational fluid dynamics) analysis is performed on the finned heat sinks. For convenience, a commercial CFD code, Flotherm, is utilized in the analysis. Though the code can handle the radiation heat transfer, the present analysis is limited to the natural convection with the base of the heat sink at a constant temperature. The continuous fin configuration is first considered due to the importance of its applications. Several experimental data are available for the vertically straight-fin heat sink and a useful correlation is also developed. For given overall fin dimensions of 15″ × 10.341″ × 2.2″, the correlations are first employed to determine the optimal fin spacing. This optimal fin spacing of 0.439 in is then used to develop the baseline CFD model. The dimensions of the baseline CFD model are as follows: Fin width (in): 10.341. Heat sink length (in): 15. Fin spacing (in): 0.439. Fin height (in): 2.0. Fin thickness (in): 0.1. Fin base plate thickness (in): 0.2. Fin numbers: 20. The baseline model with various fin spacing is analyzed and the results (heat loss from the finned heat sink) compare well with those obtained through the correlations. The analysis is extended to the staggered and in-line fin configurations because of their practical applications. Three different fin lengths, including 1″, 3″ and 5″ fin length for the staggered fin array are examined. The results indicate that the effectiveness of heat transfer is increased as the fin length increasing. The continuous fin configuration is the most efficient, and is followed by the staggered fins and then by the in-line fins.

Effect of Synthetic Jets Over Natural Convection Heat Sinks

2008 ◽  
Author(s):  
Mehmet Arik ◽  
Yogen Utturkar ◽  
Murat Ozmusul
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Operating Conditions ◽  
Heat Sinks ◽  
Junction Temperature ◽  
Allowable Limit

In moderate power electronics applications, the most preferred way of thermal management is natural convection to air with or without heat sinks. Though the use of heat sinks is fairly adequate for modest heat dissipation needs, it suffers from some serious performance limitations. Firstly, a large volume of the heat sink is required to keep the junction temperature at an allowable limit. This need arises because of the low convective film coefficients due to close spacing. In the present computational and experimental study, we propose a synthetic jet embedded heat sink to enhance the performance levels beyond two times within the same volume of a regular passive heat sink. Synthetic jets are meso-scale devices producing high velocity periodic jet streams at high velocities. As a result, by carefully positioning of these jets in the thermal real estate, the heat transfer over the surfaces can be dramatically augmented. This increase in the heat transfer rate is able to compensate for the loss of fin area happening due to the embedding of the jet within the heat sink volume, thus causing an overall increase in the heat dissipation. Heat transfer enhancements of 2.2 times over baseline natural convection cooled heat sinks are measured. Thermal resistances are compared for a range of jet operating conditions and found to be less than 0.9 K/W. Local temperatures obtained from experimental and computational agreed within ± 5%.

scholarly journals Influence of Ambient Temperature on Radiative and Convective Heat Dissipation Ratio in Polymer Heat Sinks

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2286
Author(s):  
Jan Kominek ◽  
Martin Zachar ◽  
Michal Guzej ◽  
Erik Bartuli ◽  
Petr Kotrbacek
Keyword(s):  
Heat Transfer ◽  
Ambient Temperature ◽  
Convective Heat ◽  
Heat Dissipation ◽  
High Surface ◽  
Heat Sinks ◽  
Fourth Power ◽  
Molding Process ◽  
Ambient Temperatures ◽  
University Of Technology

Miniaturization of electronic devices leads to new heat dissipation challenges and traditional cooling methods need to be replaced by new better ones. Polymer heat sinks may, thanks to their unique properties, replace standardly used heat sink materials in certain applications, especially in applications with high ambient temperature. Polymers natively dispose of high surface emissivity in comparison with glossy metals. This high emissivity allows a larger amount of heat to be dissipated to the ambient with the fourth power of its absolute surface temperature. This paper shows the change in radiative and convective heat transfer from polymer heat sinks used in different ambient temperatures. Furthermore, the observed polymer heat sinks have differently oriented graphite filler caused by their molding process differences, therefore their thermal conductivity anisotropies and overall cooling efficiencies also differ. Furthermore, it is also shown that a high radiative heat transfer leads to minimizing these cooling efficiency differences between these polymer heat sinks of the same geometry. The measurements were conducted at HEATLAB, Brno University of Technology.

Thermally Optimum Natural Convection Cooled Longitudinal-Plate Heat Sinks With Horizontal Base Plates

2001 ◽  
Author(s):  
K. K. Sikka ◽  
C. George
Keyword(s):  
Natural Convection ◽  
Heat Sink ◽  
Base Plate ◽  
Heat Sinks ◽  
Geometrical Parameters ◽  
Plate Heat ◽  
Horizontal Orientation ◽  
Fin Spacing ◽  
Base Plates ◽  
Weakly Dependent

Abstract Longitudinal-plate fin heat sinks are optimized under natural convection conditions for the horizontal orientation of the heat sink base plate. The thermal performance of the heat sinks is numerically modeled. The fin height, thickness and spacing and heat sink width are systematically varied. The numerical results are validated by experimentation. Results show that the thermal resistance of a heat sink minimizes for a certain number of fins on the base plate. The fin spacing-to-length ratio at which the minimum occurs is weakly dependent on the fin height and thickness and heat sink width. The flow fields reveal that the minimum occurs for the heat sink geometry in which the number of fins are maximized such that the flow velocity as the air exits the fins is fully developed. A correlation of the heat transfer with the heat sink geometrical parameters is also developed.

Investigation of the effects of geometrical parameters, eccentricity and perforated fins on natural convection heat transfer in a finned horizontal annulus using three dimensional lattice Boltzmann flux solver

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Mahyar Ashouri ◽  
Mohammad Mehdi Zarei ◽  
Ali Moosavi
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Transfer Rate ◽  
Lattice Boltzmann ◽  
Transfer Rate ◽  
Three Dimensional ◽  
Maximum Heat ◽  
Content Type ◽  
Dimensional Lattice ◽  
Fin Spacing

Purpose The purpose of this paper is to investigate the effects of geometrical parameters, eccentricity and perforated fins on natural convection heat transfer in a finned horizontal annulus using three-dimensional lattice Boltzmann flux solver. Design/methodology/approach Three-dimensional lattice Boltzmann flux solver is used in the present study for simulating conjugate heat transfer within an annulus. D3Q15 and D3Q7 models are used to solve the fluid flow and temperature field, respectively. The finite volume method is used to discretize mass, momentum and energy equations. The Chapman–Enskog expansion analysis is used to establish the connection between the lattice Boltzmann equation local solution and macroscopic fluxes. To improve the accuracy of the lattice Boltzmann method for curved boundaries, lattice Boltzmann equation local solution at each cell interface is considered to be independent of each other. Findings It is found that the maximum heat transfer rate occurs at low fin spacing especially by increasing the fin height and decreasing the internal-cylindrical distance. The effect of inner cylinder eccentricity is not much considerable (up to 5.2% enhancement) while the impact of fin eccentricity is more remarkable. Negative fin eccentricity further enhances the heat transfer rate compared to a positive fin eccentricity and the maximum heat transfer enhancement of 91.7% is obtained. The influence of using perforated fins is more considerable at low fin spacing although some heat transfer enhancements are observed at higher fin spacing. Originality/value The originality of this paper is to study three-dimensional natural convection in a finned-horizontal annulus using three-dimensional lattice Boltzmann flux solver, as well as to apply symmetry and periodic boundary conditions and to analyze the effect of eccentric annular fins (for the first time for air) and perforated annular fins (for the first time so far) on the heat transfer rate.

Partitioned Heat Sinks for Improved Natural Convection

2020 ◽  
Author(s):  
Todd Salamon ◽  
Roger Kempers ◽  
Brian Lynch ◽  
Kevin Terrell ◽  
Elina Simon
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Convective Heat Transfer ◽  
Antenna Arrays ◽  
Heat Sink ◽  
Massive Mimo ◽  
Vertical Plate ◽  
Numerical Models ◽  
Heat Sinks ◽  
Sensible Heat

Abstract The main drivers contributing to the continued growth of network traffic include video, mobile broadband and machine-to-machine communication (Internet of Things, cloud computing, etc.). Two primary technologies that next-generation (5G) networks are using to increase capacity to meet these future demands are massive MIMO (Multi-Input Multi-Output) antenna arrays and new frequency spectrum. The massive MIMO antenna arrays have significant thermal challenges due to the presence of large arrays of active antenna elements coupled with a reliance on natural convection cooling using vertical plate-finned heat sinks. The geometry of vertical plate-finned heat sinks can be optimized (for example, by choosing the fin pitch and thickness that minimize the thermal resistance of the heat sink to ambient air) and enhanced (for example, by embedding heat pipes within the base to improve heat spreading) to improve convective heat transfer. However, heat transfer performance often suffers as the sensible heat rise of the air flowing through the heat sink can be significant, particularly near the top of the heat sink; this issue can be especially problematic for the relatively large or high-aspect-ratio heat sinks associated with massive MIMO arrays. In this study a vertical plate-finned natural convection heat sink was modified by partitioning the heat sink along its length into distinct sections, where each partitioned section ejects heated air and entrains cooler air. This approach increases overall heat sink effectiveness as the net sensible heat rise of the air in any partitioned section is less than that observed in the unpartitioned heat sink. Experiments were performed using a standard heat sink and equivalent heat sinks partitioned into two and three sections for the cases of ducted and un-ducted natural convection with a uniform heat load applied to the rear of the heat sink. Numerical models were developed which compare well to the experimental results and observed trends. The numerical models also provide additional insight regarding the airflow and thermal performance of the partitioned heat sinks. The combined experimental and numerical results show that for relatively tall natural convection cooled heat sinks, the partitioning approach significantly improves convective heat transfer and overall heat sink effectiveness.

Experimental Study of a Single Microchannel Flow Under Non-Uniform Heat Flux

2017 ◽  
Author(s):  
Ahmed Eltaweel ◽  
Abdulla Baobeid ◽  
Ibrahim Hassan
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Dissipation ◽  
Hot Spot ◽  
Heat Fluxes ◽  
Heat Sinks ◽  
Uniform Heat Flux ◽  
Maximum Heat ◽  
Uniform Heat ◽  
Microchannel Heat Sinks

Non-uniform heat fluxes are commonly observed in thermo-electronic devices that require distinct thermal management strategies for effective heat dissipation and robust performance. The limited research available on non-uniform heat fluxes focus mostly on microchannel heat sinks while the fundamental component, i.e. a single microchannel, has received restricted attention. In this work, an experimental setup for the analysis of variable axial heat flux is used to study the heat transfer in a single microchannel with fully developed flow under the effect of different heat flux profiles. Initially a hot spot at different locations, with a uniform background heat flux, is studied at different Reynolds numbers while varying the maximum heat fluxes in order to compute the heat transfer in relation to its dependent variables. Measurements of temperature, pressure, and flow rates at a different locations and magnitudes of hot spot heat fluxes are presented, followed by a detailed analysis of heat transfer characteristics of a single microchannel under non-uniform heating. Results showed that upstream hotspots have lower tube temperatures compared to downstream ones with equal amounts of heat fluxes. This finding can be of importance in enhancing microchannel heat sinks effectiveness in reducing maximum wall temperatures for the same amount of heat released, by redistributing spatially fluxes in a descending profile.

Experimental Study of a Single Microchannel Flow Under Nonuniform Heat Flux

2019 ◽  
Vol 12 (1) ◽  
Author(s):  
Ahmed Eltaweel ◽  
Ibrahim Hassan
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Dissipation ◽  
Hot Spot ◽  
Management Strategies ◽  
Heat Fluxes ◽  
Heat Sinks ◽  
Nonuniform Heating ◽  
Maximum Heat ◽  
Microchannel Heat Sinks

Abstract Nonuniform heat fluxes are commonly observed in thermo-electronic devices that require distinct thermal management strategies for effective heat dissipation and robust performance. The limited research available on nonuniform heat fluxes focus mostly on microchannel heat sinks while the fundamental component, i.e., a single microchannel, has received restricted attention. In this work, an experimental setup for the analysis of variable axial heat flux is used to study the heat transfer in a single microchannel with fully developed flow under the effect of different heat flux profiles. Initially, a hot spot at different locations, with a uniform background heat flux, is studied at different Reynolds numbers, while varying the maximum heat fluxes in order to compute the heat transfer in relation to its dependent variables. Measurements of temperature, pressure, and flow rates at a different locations and magnitudes of hot spot heat fluxes are presented, followed by a detailed analysis of heat transfer characteristics of a single microchannel under nonuniform heating. Results showed that upstream hotspots have lower tube temperatures compared to downstream ones with equal amounts of heat fluxes. This finding can be of importance in enhancing microchannel heat sinks effectiveness in reducing maximum wall temperatures for the same amount of heat released, by redistributing spatially fluxes in a descending profile.

Cooling Performances of Perforated-Finned Heat Sinks

2016 ◽  
Author(s):  
Mohammad Reza Shaeri ◽  
Bradley Richard ◽  
Richard Bonner
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Heat Sink ◽  
Cooling System ◽  
Thermal Characteristics ◽  
Heat Sinks ◽  
Pumping Power ◽  
Maximum Heat ◽  
Maximum Heat Transfer

Cooling performances of perforated-finned heat sinks (PFHS) are investigated in the laminar forced convection heat transfer mode, through detailed experiments. Perforations like windows with square cross sections are placed on the lateral surfaces of the fins. Cooling performances are evaluated due to changes in both porosities and perforation sizes. Thermal characteristics are reported based on pumping power, in order to provide more practical insight about performances of PFHSs in real applications. It is found that at a constant perforation size, there is an optimum porosity that results in the largest heat transfer coefficient. For a fixed porosity, increasing the number of perforations (reducing the perforation size) results in an enhancement of heat transfer rate due to repeated interruption of the thermal boundary layer. The opposite trend is observed for PFHSs with larger perforation sizes. This indicates that there is an optimum perforation size and distance between perforations in order to achieve the maximum heat transfer coefficients at a constant porosity. Also, a PFHS results in a smaller temperature non-uniformity across the heat sink base, as well as a more rapid reduction in temperature non-uniformity on the heat sink base by increasing pumping power. In addition, the advantage of a PFHS to reduce the overall weight of the cooling system is incorporated into thermal characteristics of the heat sinks, and demonstrated by the mass specific heat transfer coefficient.

Sign in / Sign up

Export Citation Format

Share Document