scholarly journals Alat Pencetak Edible Straw berbasis Mikrokontroler

2021 ◽  
Vol 9 (4) ◽  
pp. 952
Author(s):  
ANAK AGUNG GDE EKAYANA ◽  
I GEDE AGUS ARI SANTIKA
Keyword(s):  
Stainless Steel ◽  
Mechanical Design ◽  
Electronic System ◽  
Heating Time ◽  
Time Range ◽  
Mold Material ◽  
Measured Temperature ◽  
Community Activities ◽  
Materials Used ◽  
The Impact

ABSTRAKPenggunaan plastik saat ini banyak digunakan diberbagai kegiatan masyarakat, dampak dari penggunaan plastik terlalu banyak menyebabkan polusi pada lingkungan. Penelitian ini bertujuan merancang dan membangun alat yang menghasilkan sedotan minuman dengan bahan yang ramah lingkungan, bahan yang digunakan menggunakan agar-agar rumput laut nutrijell yang aman untuk dikonsumsi. Alat pencetak sedotan dirancang menggunakan komponen elektronika, diantaranya sensor suhu DS18B20, mikrokontroler, elemen pemanas dan kipas. Tahapan dalam proses rancang bangun meliputi perancangan mekanik, material cetakan menggunakan stainless steel, perancangan sistem elektronika dan perancangan perangkat lunak. Hasil pengujian dari alat pencetak edible straw mendapatkan hasil sedotan yang bervariasi dari segi bentuk dan tekstur, pada proses kerjanya alat pencetak sedotan dapat mengatur waktu pemanas dari kisaran waktu 5 – 30 menit, sedotan tersebut dipanaskan selama 30 menit dari suhu awal dengan suhu terukur pada menit ke-30 adalah 62oC. Kata kunci: edible, sedotan, pemanas, mikrokontroler, agar-agar nutrijell  ABSTRACTThe use of plastic is currently widely used in various community activities, the impact of using too much plastic causes pollution to the environment. This study aims to design and build a device that produces drinking straws with environmentally friendly materials, the materials used are using nutrijell seaweed jelly which is safe for consumption. The straw printer is designed using electronic components, including the DS18B20 temperature sensor, microcontroller, heating element and fan. The stages in the design process include mechanical design, mold material using stainless steel, electronic system design and software design. The test results from the edible straw printer get straws that vary in terms of shape and texture, in the working process the straw printer can set the heating time from a time range of 5 - 30 minutes, the straws are heated for 30 minutes from the initial temperature with a measured temperature in minutes 30th is 62oC.Keywords: edible, straw, heater, microcontroller, nutrijell jelly

Environmental Conservation Through Study Value of Bali Aga Tenganan Pegringsingan Community Culture

2020 ◽  
Vol 21 (1) ◽  
pp. 27
Author(s):  
Nyoman Wijana ◽  
I Gusti Agung Nyoman Setiawan ◽  
Sanusi Mulyadiharja ◽  
I Gede Astra Wesnawa ◽  
Putu Indah Rahmawati
Keyword(s):  
Cultural Values ◽  
Environmental Conservation ◽  
Time Orientation ◽  
Cultural Value ◽  
Community Culture ◽  
Community Activities ◽  
Orientation Time ◽  
The Impact ◽  
Relational Orientation

This research aimed to know the implementation of environmental conservation in terms of cultural value orientation, including humanistic nature orientation, man-nature orientation, time orientation, activity orientation, and relational orientation. The population of this research was the entire community in traditional village Tenganan Pegringsingan, Karangasem, Bali. This research sample amounted to 25 people, consisting of the conventional village apparatus, community leaders, and the general public. Methods of data collection were the method of observation, interview, questionnaire, and checklist. The collected data were analyzed descriptively. This research indicated that the orientation of cultural values of humanistic nature orientation and man-nature orientation had an excellent quality. The time orientation, activity orientation, and relational orientation parameters had good quality. Culture in the study community generally showed a positive thing, so the impact of culture on the quality of the environment, in general, was excellent. The results of observations in the field revealed that there were all community activities at Tenganan Pegringsingan that could not cause environmental pollution. Therefore, the role of traditional regulation or awig-awig to regulate environmental and social-culture.

Peculiarities of tool material wear at polymeric composite blank cutting

2018 ◽  
Vol 2018 (7) ◽  
pp. 27-31
Author(s):  
Юрий Зубарев ◽  
Yuriy Zubarev ◽  
Александр Приемышев ◽  
Alexsandr Priyomyshev
Keyword(s):  
Tool Wear ◽  
Tool Material ◽  
Polymeric Composite ◽  
Physical Models ◽  
Technological Parameters ◽  
Tool Materials ◽  
Materials Used ◽  
The Impact ◽  
Material Wear

Tool materials used for polymeric composite blank machining, kinds of tool material wear arising at machining these blanks, and also the impact of technological parameters upon tool wear are considered. The obtained results allow estimating the potentialities of physical models at polymeric composite blanks cutting.

Comparative analytical study of Ashuddha Karaveera and Shuddha Karaveera

2017 ◽  
Vol 2 (2) ◽  
Author(s):  
Apeksha D. Patil ◽  
Dhiraj B. Patil
Keyword(s):  
Stainless Steel ◽  
Analytical Study ◽  
Warm Water ◽  
Foreign Matter ◽  
Steel Vessel ◽  
Mild Heat ◽  
Stainless Steel Vessel ◽  
The Impact

Karaveera (Cerebra thevetia Linn.) is reported under Upavisha Dravya in classical ayurvedic pharmacopeias. It is observed that Shodhana (purification procedures) of the mool should be carried out before its internal administration. There are different Shodhana methods mentioned in Ayurveda. In this study Godugdha was used as media. The impact of Shodhana was evaluated by physico analytical study. It clearly proves physico analytical changes during Shodhana. Ashuddha Karaveera was taken on white clean cloth and they dumped in Pottali with Godugdha. Pottali was tied to middle of wooden rod dipped in Godugdha in stainless steel vessel and mild heat given to pottali in Dolayantra. Shuddha Karaveera was obtained and then washed with leuk warm water and dried. Ashuddha Karaveera contains toxin in it which was removed after Shodhana process. So that foreign matter, loss on drying was less in Shuddha Karaveera and due to Shodhan process with Godugdha total ash, acid insoluble ash was more than that of Ashuddha Karaveera.

scholarly journals Impact of Solidification on Inclusion Morphology in ESR and PESR Remelted Martensitic Stainless Steel Ingots

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 408
Author(s):  
Ewa Sjöqvist Persson ◽  
Sofia Brorson ◽  
Alec Mitchell ◽  
Pär G. Jönsson
Keyword(s):  
Stainless Steel ◽  
Martensitic Stainless Steel ◽  
Dendritic Structure ◽  
Steel Grade ◽  
Solidification Structure ◽  
Production Scale ◽  
Steel Grades ◽  
Steel Ingots ◽  
Columnar Dendritic Structure ◽  
The Impact

This study focuses on the impact of solidification on the inclusion morphologies in different sizes of production-scale electro-slag remelting (ESR) and electro-slag remelting under a protected pressure-controlled atmosphere, (PESR), ingots, in a common martensitic stainless steel grade. The investigation has been carried out to increase the knowledge of the solidification and change in inclusion morphologies during ESR and PESR remelting. In order to optimize process routes for different steel grades, it is important to define the advantages of different processes. A comparison is made between an electrode, ESR, and PESR ingots with different production-scale ingot sizes, from 400 mm square to 1050 mm in diameter. The electrode and two of the smallest ingots are from the same electrode charge. The samples are taken from both the electrode, ingots, and rolled/forged material. The solidification structure, dendrite arm spacing, chemical analyzes, and inclusion number on ingots and/or forged/rolled material are studied. The results show that the larger the ingot and the further towards the center of the ingot, the larger inclusions are found. As long as an ingot solidifies with a columnar dendritic structure (DS), the increase in inclusion number and size with ingot diameter is approximately linear. However, at the ingot size (1050 mm in diameter in this study) when the center of the ingot converts to solidification in the equiaxial mode (EQ), the increase in number and size of the inclusions is much higher. The transition between a dendritic and an equiaxial solidification in the center of the ingots in this steel grade takes place in the region between the ingot diameters of 800 and 1050 mm.

scholarly journals Analysis of the Impact on the Mechanical Properties of Modification of Oligohydroxyethers in Organic Solvent Solution with Rubbers

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 519
Author(s):  
Vitalii Bezgin ◽  
Agata Dudek ◽  
Adam Gnatowski
Keyword(s):  
Mechanical Properties ◽  
Scientific Paper ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Molecular Weights ◽  
Wide Range ◽  
Strength Tests ◽  
Materials Used ◽  
Styrene Butadiene ◽  
The Impact

This paper proposes and presents the chemical modification of linear hydroxyethers (LHE) with different molecular weights (380, 640, and 1830 g/mol) with the addition of three types of rubbers (polysulfide rubber (PSR), polychloroprene rubber (PCR), and styrene-butadiene rubber (SBR)). The main purpose of choosing this type of modification and the materials used was the possibility to use it in industrial settings. The modification process was conducted for a very wide range of modifier additions (rubber) per 100 g LHE. The materials obtained in the study were subjected to strength tests in order to determine the effect of the modification on functional properties. Mechanical properties of the modified materials were improved after the application of the modifier (rubber) to polyhydroxyether (up to certain modifier content). The most favorable changes in the tested materials were registered in the modification of LHE-1830 with PSR. In the case of LHE-380 and LHE-640 modified in cyclohexanol (CH) and chloroform (CF) solutions, an increase in the values of the tested properties was also obtained, but to a lesser extent than for LHE-1830. The largest changes were registered for LHE-1830 with PSR in CH solution: from 12.1 to 15.3 MPa for compressive strength tests, from 0.8 to 1.5 MPa for tensile testing, from 0.8 to 14.7 MPa for shear strength, and from 1% to 6.5% for the maximum elongation. The analysis of the available literature showed that the modification proposed by the authors has not yet been presented in any previous scientific paper.

scholarly journals Strength Enhancement of Superduplex Stainless Steel Using Thermomechanical Processing

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1094
Author(s):  
M. A. Lakhdari ◽  
F. Krajcarz ◽  
J. D. Mithieux ◽  
H. P. Van Landeghem ◽  
M. Veron
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Thermomechanical Processing ◽  
Tensile Tests ◽  
Image Correlation ◽  
Strength Enhancement ◽  
Industrial Material ◽  
Superduplex Stainless Steel ◽  
The Impact ◽  
Strength Improvement

The impact of microstructure evolution on mechanical properties in superduplex stainless steel UNS S32750 (EN 1.4410) was investigated. To this end, different thermomechanical treatments were carried out in order to obtain clearly distinct duplex microstructures. Optical microscopy and scanning electron microscopy, together with texture measurements, were used to characterize the morphology and the preferred orientations of ferrite and austenite in all microstructures. Additionally, the mechanical properties were assessed by tensile tests with digital image correlation. Phase morphology was not found to significantly affect the mechanical properties and neither were phase volume fractions within 13% of the 50/50 ratio. Austenite texture was the same combined Goss/Brass texture regardless of thermomechanical processing, while ferrite texture was mainly described by α-fiber orientations. Ferrite texture and average phase spacing were found to have a notable effect on mechanical properties. One of the original microstructures of superduplex stainless steel obtained here shows a strength improvement by the order of 120 MPa over the industrial material.

scholarly journals Are Biogenic and Pyrogenic Mesoporous SiO2 Nanoparticles Safe for Normal Cells?

Molecules ◽  
2021 ◽  
Vol 26 (5) ◽  
pp. 1427
Author(s):  
Katarzyna Solarska-Ściuk ◽  
Kinga Adach ◽  
Sylwia Cyboran-Mikołajczyk ◽  
Dorota Bonarska-Kujawa ◽  
Agnieszka Rusak ◽  
...  
Keyword(s):  
Mesoporous Silica ◽  
Silica Nanoparticles ◽  
Biological Effects ◽  
Mesoporous Silica Nanoparticles ◽  
Volume Ratio ◽  
Sio2 Nanoparticles ◽  
Amorphous Structure ◽  
Intracellular Ros ◽  
Materials Used ◽  
The Impact

Silicon dioxide, in the form of nanoparticles, possesses unique physicochemical properties (size, shape, and a large surface to volume ratio). Therefore, it is one of the most promising materials used in biomedicine. In this paper, we compare the biological effects of both mesoporous silica nanoparticles extracted from Urtica dioica L. and pyrogenic material. Both SEM and TEM investigations confirmed the size range of tested nanoparticles was between 6 and 20 nanometers and their amorphous structure. The cytotoxic activity of the compounds and intracellular ROS were determined in relation to cells HMEC-1 and erythrocytes. The cytotoxic effects of SiO2 NPs were determined after exposure to different concentrations and three periods of incubation. The same effects for endothelial cells were tested under the same range of concentrations but after 2 and 24 h of exposure to erythrocytes. The cell viability was measured using spectrophotometric and fluorimetric assays, and the impact of the nanoparticles on the level of intracellular ROS. The obtained results indicated that bioSiO2 NPs, present higher toxicity than pyrogenic NPs and have a higher influence on ROS production. Mesoporous silica nanoparticles show good hemocompatibility but after a 24 h incubation of erythrocytes with silica, the increase in hemolysis process, the decrease in osmotic resistance of red blood cells, and shape of erythrocytes changed were observed.

scholarly journals Green Packaging from Consumer and Business Perspectives

2021 ◽  
Vol 13 (3) ◽  
pp. 1356
Author(s):  
Gonzalo Wandosell ◽  
María C. Parra-Meroño ◽  
Alfredo Alcayde ◽  
Raúl Baños
Keyword(s):  
Sustainable Development ◽  
Raw Materials ◽  
Research Activity ◽  
Word Clouds ◽  
Climate Action ◽  
Green Packaging ◽  
Materials Used ◽  
Societal Challenge ◽  
Corporate Social ◽  
The Impact

Sustainable development is a global objective that aims to address the societal challenge of climate action, the environment, resource efficiency, and raw materials. In this sense, an important strategy is the promotion of green packaging, that is, the use of sustainable materials and designs for the packaging of goods. In recent years, many research works have been published in the specialised area covering the different perspectives and dimensions of green packaging. However, to our knowledge, no previous investigations have analysed the research activity on green packaging from business and consumer perspectives. The present study intends to fill this gap by analysing all of the publications found in the Scopus database with the help of visual analytic tools, including word clouds and Gephi network visualization software. More specifically, our study analyses the impact of green packaging from business and consumer viewpoints, including some specific issues such as the design and materials used in green packaging, green packaging costs, marketing strategies and corporate social responsibility related to green packaging, and the impact of green packaging in waste management, the circular economy, logistics, and supply chain management. The results obtained reveal the growing interest of scholars and researchers in all of these dimensions, as is made patently clear by the increasing number of journal publications in recent years. The practical implications of this study are significant, given the growing awareness among companies and consumers about the importance of the promotion of sustainable development through green packaging alternatives. More specifically, the results of this research could be very useful for all of those agents who are interested in learning about the main lines of research being developed in the field of green packaging.

scholarly journals Microstructure and Mechanical Properties of Heat-Affected Zone of Repeated Welding AISI 304N Austenitic Stainless Steel by Gleeble Simulator

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 773
Author(s):  
Y.H. Guo ◽  
Li Lin ◽  
Donghui Zhang ◽  
Lili Liu ◽  
M.K. Lei
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Impact Energy ◽  
Heat Affected Zone ◽  
Ferrite Content ◽  
Equipment Safety ◽  
Microstructure And Mechanical Properties ◽  
Δ Ferrite ◽  
The Impact

Heat-affected zone (HAZ) of welding joints critical to the equipment safety service are commonly repeatedly welded in industries. Thus, the effects of repeated welding up to six times on the microstructure and mechanical properties of HAZ for AISI 304N austenitic stainless steel specimens were investigated by a Gleeble simulator. The temperature field of HAZ was measured by in situ thermocouples. The as-welded and one to five times repeated welding were assigned as-welded (AW) and repeated welding 1–5 times (RW1–RW5), respectively. The austenitic matrices with the δ-ferrite were observed in all specimens by the metallography. The δ-ferrite content was also determined using magnetic and metallography methods. The δ-ferrite had a lathy structure with a content of 0.69–3.13 vol.%. The austenitic grains were equiaxial with an average size of 41.4–47.3 μm. The ultimate tensile strength (UTS) and yield strength (YS) mainly depended on the δ-ferrite content; otherwise, the impact energy mainly depended on both the austenitic grain size and the δ-ferrite content. The UTS of the RW1–RW3 specimens was above 550 MPa following the American Society of Mechanical Engineers (ASME) standard. The impact energy of all specimens was higher than that in ASME standard at about 56 J. The repeated welding up to three times could still meet the requirements for strength and toughness of welding specifications.

Sign in / Sign up

Export Citation Format

Share Document