scholarly journals Phase composition, microstructure and microhardness of alloy In–Sn, obtained by rapid crystallization

2018 ◽  
Vol 63 (3) ◽  
pp. 290-296
Author(s):  
V. G. Shepelevich ◽  
O. V. Gusakova ◽  
S. V. Husakova
Keyword(s):  
Phase Composition ◽  
Volume Fraction ◽  
Electron Backscatter Diffraction ◽  
State Diagram ◽  
Grain Structure ◽  
Unstable State ◽  
Β Phase ◽  
Pole Figures ◽  
Distribution Of Components ◽  
Backscatter Diffraction

The results of studying of the structure and properties of the In – 42 at.% Sn alloy in the form of foil obtained by the method of rapid solidification with a cooling rate of the melt of at least 105K/s are presented. X-ray diffraction analysis showed that the phase composition of the alloy corresponds to the equilibrium state diagram. Foils consist of an InSn4compound (γ-phase) and an In3Sn compound (β-phase). The grain structure of foil was studied by electron backscatter diffraction technique. It is established that the foil have a microcrystalline structure. The parameters of the microstructure are determined by the method of random linear secants: the volume fraction of the phases, average chord length of the random linear secant on the inclusions of each phase, the specific surface of the interface. Microstructure and distribution of components was also studied for both foil surfaces. The texture of both phases of the polycrystalline foils was studied by the method of inverse pole figures. It is established that the initial foils of the investigated alloy are in an unstable state. It is shown that an increase in the microhardness of the alloy during aging and annealing caused by change in the parameters of the grain structure.

Physical Based Microstructure Modelling Coupled with Nucleation Theory during and after Hot Forming of AA5083

2010 ◽  
Vol 89-91 ◽  
pp. 509-514
Author(s):  
Pavel Sherstnev ◽  
Christof Sommitsch ◽  
Stefan Mitsche ◽  
Carsten Melzer
Keyword(s):  
Aluminium Alloy ◽  
Hot Rolling ◽  
Volume Fraction ◽  
Electron Backscatter Diffraction ◽  
Grain Structure ◽  
Nucleation Theory ◽  
Structure Evolution ◽  
Nucleation Sites ◽  
Nucleation Mechanisms ◽  
Backscatter Diffraction

A physical model based on three types of dislocations and three nucleation sites for recrystallized grain is applied to hot rolling simulation. This model was implemented into a commercial Finite Element (FE) analysis package FORGE 2008 to calculate both the structure evolution during and the recrystallized volume fraction after hot working of aluminium alloy 5083. It is shown that the main nucleation mechanisms in the aluminium alloy are the particle stimulated nucleation (PSN) and nucleation at grain boundaries. Hence the precipitation kinetics during homogenisation was investigated by use of the thermodynamic calculation software MatCalc. To validate the simulation results hot rolling experiments were performed by means of a laboratory mill. The grain structure evolution was analysed by electron backscatter diffraction (EBSD).

Specifics of Microstructure and Phase Composition of High-Speed Steel R6M5

2013 ◽  
Vol 404 ◽  
pp. 20-24 ◽  
Author(s):  
Маzhyn Skakov ◽  
Bauyrzhan Rakhadilov ◽  
Gaukhar Karipbayeva
Keyword(s):  
Phase Composition ◽  
High Speed ◽  
Volume Fraction ◽  
Electron Backscatter Diffraction ◽  
High Speed Steel ◽  
Spherical Shape ◽  
Xrd Analysis ◽  
Steel R6m5 ◽  
Solid Carbide ◽  
Backscatter Diffraction

In this paper microstructure, morphology, elemental composition, phase composition and crystal structure of the sample steel R6M5 were investigate by using the methods of scanning electron microscopy, electron backscatter diffraction (EBSD) analysis and X-ray diffraction (XRD) analysis. Determined that the microstructure of steel R6M5 after hardening and three-time tempering consists of tempered martensite and solid carbide M6C and MC-type with spherical shape and a diameter of less than 3 μm. Detected that the volume fraction of each carbide amounted to 10.4±0.6% and 2.3±0.4% - for grey and bright carbides, respectively, and that the sizes of bright carbides particles in the microstructure of steel R6M5 are 0.4-4,5 μm, and the sizes of grey carbides particles are 0.5-1.1 μm. XRD analysis showed that the main carbides in the studied steel are carbides М6С and MC, which have complicated the FCC crystal lattice and the Fd3m spatial group. Determined that carbides are uniform and monocrystalline. ESBD analysis with the support of the XRD analysis showed that carbides spherical shape М6С fit to Fe3W3C composition.

Microstructure and Microtexture Evolution of Invar Alloy after Cross Accumulative Roll Bonding (CARB) Compared to ARB

2016 ◽  
Vol 879 ◽  
pp. 744-749 ◽  
Author(s):  
Kamel Tirsatine ◽  
Hiba Azzeddine ◽  
Thierry Baudin ◽  
Anne Laure Helbert ◽  
Francois Brisset ◽  
...  
Keyword(s):  
Accumulative Roll Bonding ◽  
Volume Fraction ◽  
Electron Backscatter Diffraction ◽  
Rolling Direction ◽  
Grain Structure ◽  
Subgrain Structure ◽  
Roll Bonding ◽  
Ni Alloy ◽  
Backscatter Diffraction ◽  
Microstructure And Microtexture

The microstructure and microtexture evolution of a Fe-36%Ni alloy processed by cross accumulative roll-bonding was investigated using Electron BackScatter Diffraction. Deformation led to the development of elongated ultrafine grains parallel to the rolling direction that subsequently became more equiaxed. The grains were more effectivelly refined after CARB than after ARB processing. The grain aspect ratio (l/L) decreased (which means a trend towards elongated sub-grain structure) after 2 and 3 CARB processing cycles and then increased (which means a trend towards equiaxed subgrain structure) from 4 to 5 cycles. The fraction of HAGB, CSL boundaries and the estimated deformed volume fraction gradually increased with increasing number of CARB cycles. Copper-type texture was observed after CARB odd cycles (RD//RD), while after even cycles (RD//TD) a new texture component named H ({012}<221>) was observed.

Cross Section Analysis of Cu Filled TSVs Based on High Throughput Plasma-FIB Milling

2012 ◽  
Author(s):  
Frank Altmann ◽  
Jens Beyersdorfer ◽  
Jan Schischka ◽  
Michael Krause ◽  
German Franz ◽  
...  
Keyword(s):  
High Resolution ◽  
Cross Section ◽  
High Throughput ◽  
Cross Sections ◽  
Electron Backscatter Diffraction ◽  
Grain Structure ◽  
Electron Backscatter ◽  
Section Surface ◽  
Backscatter Diffraction ◽  
Section Analysis

Abstract In this paper the new Vion™ Plasma-FIB system, developed by FEI, is evaluated for cross sectioning of Cu filled Through Silicon Via (TSV) interconnects. The aim of the study presented in this paper is to evaluate and optimise different Plasma-FIB (P-FIB) milling strategies in terms of performance and cross section surface quality. The sufficient preservation of microstructures within cross sections is crucial for subsequent Electron Backscatter Diffraction (EBSD) grain structure analyses and a high resolution interface characterisation by TEM.

scholarly journals Effect of strain rate on α-lath thickness of TC17 alloy after deformation and subsequent heat treatment

2020 ◽  
Vol 321 ◽  
pp. 13003
Author(s):  
Zimin Lu ◽  
Jiao Luo ◽  
Miaoquan Li
Keyword(s):  
Heat Treatment ◽  
Strain Rate ◽  
Electron Backscatter Diffraction ◽  
Phase Region ◽  
Subsequent Heat Treatment ◽  
Strain Rates ◽  
Optical Micrograph ◽  
Β Phase ◽  
Electron Backscatter ◽  
Backscatter Diffraction

Effect of strain rate on α-lath thickness of TC17 alloy with a basketweave microstructure was studied in the present work. For this purpose, this alloy was deformed in the β phase region and subsequently soluted and aged in α+β phase region. Moreover, optical micrograph (OM) and electron backscatter diffraction (EBSD) were applied to analyze the change of lath thickness at different strain rates. The result showed that α-lath thickness increased with increasing strain rate. This phenomenon was possibly attributed to the higher degree of variant selection (DVS) at higher strain rate (0.1 s-1). The higher DVS was beneficial for the formation of parallel α-lath colonies during cooling after deformation. And, these parallel α-lath colonies would more easily grow up and coarsen during subsequent heat treatment. Therefore, α-lath at higher strain rate is more thick.

scholarly journals Increase in the Mechanical Strength of Mg-8Gd-3Y-1Zn Alloy Containing Long-Period Stacking Ordered Phases Using Equal Channel Angular Pressing Processing

Metals ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 221 ◽  
Author(s):  
Gerardo Garces ◽  
Pablo Pérez ◽  
Rafael Barea ◽  
Judit Medina ◽  
Andreas Stark ◽  
...  
Keyword(s):  
Thermal Treatment ◽  
Yield Stress ◽  
Equal Channel Angular Pressing ◽  
Volume Fraction ◽  
Extrusion Direction ◽  
Grain Structure ◽  
Long Period ◽  
Angular Pressing ◽  
Β Phase ◽  
Ordered Phases

The evolution of the microstructure and mechanical properties during equal channel angular pressing processing has been studied in an extruded Mg-Gd-Y-Zn alloy containing long-period stacking ordered phases. After extrusion, the microstructure is characterized by the presence of long-period stacking ordered fibers elongated along the extrusion direction within the magnesium matrix. The grain structure is a mixture of randomly oriented dynamic recrystallized and coarse highly oriented non-dynamic recrystallized grains. Rare-earth atoms are in solid solution after extrusion at 400 °C and precipitation takes place during the thermal treatment at 200 °C. Precipitation of β’ prismatic plates and lamellar γ’ in the basal plane increases the tensile yield stress from 325 to 409 MPa. During equal channel angular pressing processing at 300 °C, the volume fraction of dynamic recrystallized grains continuously increases with the strain introduced during the equal channel angular pressing process. Precipitation of β phase is equally observed at grain boundaries of the ECAPed alloy. Dynamic recrystallized grain size decreases from 1.8 µm in the extruded material to 0.5 µm in the ECAPed alloy. Thermal treatment at 200 °C of ECAPed materials results in an increase of the yield stress up to 456 MPa, which is maintained up to 200 °C.

Defining the hematite topotaxial crystal growth in magnetite–hematite phase transformation

2020 ◽  
Vol 53 (4) ◽  
pp. 896-903
Author(s):  
Flávia Braga de Oliveira ◽  
Gilberto Álvares da Silva ◽  
Leonardo Martins Graça
Keyword(s):  
Electron Backscatter Diffraction ◽  
Inverse Pole Figure ◽  
Orientation Relationships ◽  
Transformation Matrices ◽  
Hematite Phase ◽  
Pole Figures ◽  
Magnetite Crystal ◽  
Diffraction Patterns ◽  
Backscatter Diffraction ◽  
Specific Orientation

Magnetite and hematite iron oxides are minerals of great economic and scientific importance. The oxidation of magnetite to hematite is characterized as a topotaxial reaction in which the crystallographic orientations of the hematite crystals are determined by the orientation of the magnetite crystals. Thus, the transformation between these minerals is described by specific orientation relationships, called topotaxial relationships. This study presents electron-backscatter diffraction analyses conducted on natural octahedral crystals of magnetite partially transformed into hematite. Inverse pole figure maps and pole figures were used to establish the topotaxial relationships between these phases. Transformation matrices were also applied to Euler angles to assess the diffraction patterns obtained and confirm the identified relationships. A new orientation condition resulting from the magnetite–hematite transformation was characterized, defined by the parallelism between the octahedral planes {111} of magnetite and rhombohedral planes \{10\bar {1}1\} of hematite. Moreover, there was a coincidence between one of the octahedral planes of magnetite and the basal {0001} plane of hematite, and between dodecahedral planes {110} of magnetite and prismatic planes \{11\bar {2}0\} of hematite. All these three orientation conditions are necessary and define a growth model for hematite crystals from a magnetite crystal. A new topotaxial relationship is also proposed: (111)Mag || (0001)Hem and (\bar {1}\bar {1}1)_{\rm Mag} || (10\bar {1}1)_{\rm Hem}.

Deformation Structures in a Duplex Stainless Steel

2018 ◽  
Vol 941 ◽  
pp. 176-181 ◽  
Author(s):  
Karin Yvell ◽  
Göran Engberg
Keyword(s):  
Electron Backscatter Diffraction ◽  
Texture Evolution ◽  
True Strain ◽  
Strain Curve ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Deformation Structure ◽  
Pole Figures ◽  
Two Phases ◽  
Backscatter Diffraction

The evolution of the deformation structure with strain has been studied using electron backscatter diffraction (EBSD). Samples from interrupted uniaxial tensile tests and from a cyclic tension/compression test were investigated. The evolution of low angle boundaries (LABs) was studied using boundary maps and by measuring the LAB density. From calculations of local misorientations, smaller orientation changes in the substructure can be illustrated. The different orientations developed with strain within a grain, due to operation of different slip systems in different parts of the grain, were studied using a misorientation profile showing substantial orientation changes after a true strain of 0.24. The texture evolution with increasing strain was followed by using inverse pole figures (IPFs). The observed substructure development in the ferritic and austenitic phases could be successfully correlated with the stress-strain curve from a tensile test. LABs were first observed in the different phases when the strain hardening rate changed in appearance indicating that cross slip started to operate as a significant dislocation recovery mechanism. The evolution of the deformation structure is concluded to occur in a similar manner in the austenitic and ferritic phases but with different texture evolution for the two phases.

scholarly journals Microstructure and Texture Evolutions During Deep Drawing of Mg–Al–Mn Sheets at Elevated Temperatures

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3608 ◽  
Author(s):  
Jae-Hyung Cho ◽  
Sang-Ho Han ◽  
Geon Young Lee
Keyword(s):  
Dynamic Recrystallization ◽  
Deep Drawing ◽  
Elevated Temperatures ◽  
Tensile Deformation ◽  
Electron Backscatter Diffraction ◽  
Texture Evolution ◽  
Grain Structure ◽  
Transmission Electron ◽  
Backscatter Diffraction ◽  
Twin Roll

Texture and microstructure evolution of ingot and twin-roll casted Mg–Al–Mn magnesium sheets were examined during deep drawing at elevated temperatures. The twin-roll casted sheets possessed smaller grain sizes and weaker basal intensity levels than the ingot-casted sheets. The strength and elongation at room temperature for the twin-roll casted sheets were greater than those of the ingot-casted sheets. At elevated temperatures, the ingot-casted sheets showed better elongation than the twin-roll casted sheets. Different size and density of precipitates were examined using transmission electron microscopy (TEM) for both ingot-casted and twin-roll-casted sheets. The deep drawing process was also carried out at various working temperatures and deformation rates, 225 °C to 350 °C and 30 mm/min to 50 mm/min, respectively. The middle wall part of cups were mainly tensile deformation, and the lower bent regions of drawn cups were most thinned region. Overall, the ingot-casted sheets revealed better deep drawability than the twin-roll casted sheets. Microstructure and texture evolution of the top, middle and lower parts of drawn cups were investigated using electron backscatter diffraction. Increased deformation rate is important to activate tensile twins both near the bent and flange areas. Ingot casted sheets revealed more tensile twins than twin-roll casted sheets. Increased working temperature is important to activate non-basal slips and produce the DRXed grain structure in the flange. Dynamic recrystallization were frequently found in the top flanges of the cups. Both tensile twins and non-basal slips contributed to occurrence of the dynamic recrystallization in the flange.

Shear Pressing for Grain Refinement of Al-Mg-Li Sheet

2007 ◽  
Vol 546-549 ◽  
pp. 885-888
Author(s):  
Yu Xuan Du ◽  
Xin Ming Zhang ◽  
Ling Ying Ye ◽  
Zhi Hui Luo
Keyword(s):  
Shear Deformation ◽  
Grain Refinement ◽  
Electron Backscatter Diffraction ◽  
Grain Structure ◽  
Grain Refining ◽  
Metallic Materials ◽  
Inclined Plane ◽  
Fine Grained ◽  
Electron Backscatter ◽  
Backscatter Diffraction

A novel shear-deformation technique, named ‘shear pressing’ (SP), was developed for fabrication of plate-shaped fine grained metallic materials. The principle of SP is that a material is subjected to shear deformation by utilizing pressing with inclined plane dies. A micrometer order grain structure was obtained in an Al-Mg-Li alloy at strain of ε = -2.3 by utilizing this technique. The grain refinement sequences during pressing were examined by electron backscatter diffraction. The enhancement of grain refinement to the Al-Mg-Li alloy was compared with plane strain compression (PSC) at similar strains. The effect of the shear strain on the accelerated grain refining during compressing has been discussed.

Sign in / Sign up

Export Citation Format

Share Document