Thermal Failure Analysis of Functional Failures by IR Lock-in Thermal Emission

2019 ◽  
Author(s):  
Paul Hubert P. Llamera ◽  
Camille Joyce G. Garcia-Awitan
Keyword(s):  
Integrated Circuits ◽  
Failure Analysis ◽  
Near Infrared ◽  
Thermal Emission ◽  
Fault Localization ◽  
Fault Isolation ◽  
Distinct Advantage ◽  
Infra Red ◽  
Emission Microscopy ◽  
Lock In

Abstract Lock-in thermography (LIT), known as a powerful nondestructive fault localization technique, can also be used for microscopic failure analysis of integrated circuits (ICs). The dynamic characteristic of LIT in terms of measurement, imaging and sensitivity, is a distinct advantage compared to other thermal fault localization methods as well as other fault isolation techniques like emission microscopy. In this study, LIT is utilized for failure localization of units exhibiting functional failure. Results showed that LIT was able to point defects with emissions in the mid-wave infra-red (MWIR) range that Photo Emission Microscopy (PEM) with near infrared (NIR) to short- wave infra-red (SWIR) detection wavelength sensitivity cannot to detect.

Failure Analysis of Sub-Micron Semiconductor Integrated Circuit Using Backside Photon Emission Microscopy

1999 ◽  
Author(s):  
Soon Lim ◽  
Jian Hua Bi ◽  
Lian Choo Goh ◽  
Soh Ping Neo ◽  
Sudhindra Tatti
Keyword(s):  
Integrated Circuits ◽  
Failure Analysis ◽  
Integrated Circuit ◽  
Flip Chip ◽  
Photon Emission ◽  
Fault Isolation ◽  
Integrated Circuit Fabrication ◽  
Circuit Fabrication ◽  
Emission Microscopy ◽  
On Chip

Abstract The progress of modern day integrated circuit fabrication technology and packaging has made fault isolation using conventional emission microscopy via the top of the integrated circuit more difficult, if not impossible. This is primarily due to the use of increased levels and density of metal-interconnect, and the advent of new packaging technology, e.g. flip-chip, ball-grid array and lead-on-chip, etc. Backside photon emission microscopy, i.e. performing photon emission microscopy through the bulk of the silicon via the back of the integrated circuit is a solution to this problem. This paper outlines the failure analysis of sub-micron silicon integrated circuits using backside photon emission microscopy. Sample preparation, practical difficulties encountered and case histories will be discussed.

High Resolution Backside Thermography Using a Numerical Aperture Increasing Lens

2003 ◽  
Author(s):  
S. Thorne ◽  
S. Ippolito ◽  
M. Eraslan ◽  
B. Goldberg ◽  
M.S. Ünlü ◽  
...  
Keyword(s):  
High Resolution ◽  
Integrated Circuits ◽  
Failure Analysis ◽  
Visual Inspection ◽  
Thermal Emission ◽  
Numerical Aperture ◽  
Specific Component ◽  
Feature Size ◽  
Analytical Technique ◽  
Emission Microscopy

Abstract As the feature size in integrated circuits (ICs) become smaller, the techniques we use to localize defects must also progress to the level that they can resolve potential errors. Additionally, because most errors cannot be identified by visual inspection alone, it is necessary to develop techniques, such as thermography, with the capability of localizing failures to the specific component or defect at fault. This paper will review the theory and application of an advanced subsurface (through the substrate) analytical technique for IC failure analysis – solid immersion lens thermal emission microscopy.

Comparison of Photon and Thermal Emission Microscopy for Dynamic Fault Isolation

2015 ◽  
Author(s):  
S.H. Goh ◽  
G.F. You ◽  
Alan Tan ◽  
C.V. Bharadwaj ◽  
Hu Hao ◽  
...  
Keyword(s):  
Thermal Emission ◽  
Photon Emission ◽  
Fault Localization ◽  
Optical Resolution ◽  
Fault Isolation ◽  
Thermal Microscopy ◽  
Emission Microscopy

Abstract Unlike photon emission microscopy which is usually the first go-to technique in tester-based or dynamic electrical fault localization, infrared thermal microscopy does not play a similar routine role despite its comparable ease in application. While thermal emission lacks in optical resolution, we demonstrate superior sensitivity and accuracy over photon emission on dynamic fault localization of backend-of-line short defects.

Failure Analysis of Killer Defects and Yield Enhancement of Flat ROM Devices in Wafer Fabrication

2000 ◽  
Author(s):  
Y. N. Hua ◽  
Z. R. Guo ◽  
L. H. An ◽  
Shailesh Redkar
Keyword(s):  
Electron Microscope ◽  
Failure Analysis ◽  
Fault Isolation ◽  
Yield Enhancement ◽  
Wafer Fabrication ◽  
X Ray ◽  
Particle Contamination ◽  
Emission Microscopy ◽  
Microscopy Techniques ◽  
Scanning Electron

Abstract In this paper, some low yield cases in Flat ROM device (0.45 and 0.6 µm) were investigated. To find killer defects and particle contamination, KLA, bitmap and emission microscopy techniques were used in fault isolation. Reactive ion etching (RIE) and chemical delayering, 155 Wright Etch, BN+ Etch and scanning electron microscope (SEM) were used for identification and inspection of defects. In addition, energy-dispersive X-ray microanalysis (EDX) was used to determine the composition of the particle or contamination. During failure analysis, seven kinds of killer defects and three killer particles were found in Flat ROM devices. The possible root causes, mechanisms and elimination solutions of these killer defects/particles were also discussed.

A Sample Preparation on Decapsulation Methodology for Effective Failure Analysis on Thin Small Leadless (TSLP) Flip Chip Package with Copper Pillar (CuP) Bump Interconnect Technology

2014 ◽  
Author(s):  
Gwee Hoon Yen ◽  
Ng Kiong Kay
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Flip Chip ◽  
Fault Localization ◽  
Cost Effective ◽  
Fault Isolation ◽  
Voltage Contrast ◽  
Interconnect Technology

Abstract Today, failure analysis involving flip chip [1] with copper pillar bump packaging technologies would be the major challenges faced by analysts. Most often, handling on the chips after destructive chemical decapsulation is extremely critical as there are several failure analysis steps to be continued such as chip level fault localization, chip micro probing for fault isolation, parallel lapping [2, 3, 4] and passive voltage contrast. Therefore, quality of sample preparation is critical. This paper discussed and demonstrated a quick, reliable and cost effective methodology to decapsulate the thin small leadless (TSLP) flip chip package with copper pillar (CuP) bump interconnect technology.

Pseudo-Dynamic Fault Isolation Technique Using Backside Emission Microscopy – Case Study, Where All Other Methods Fail

2002 ◽  
Author(s):  
Yoav Weizman ◽  
Ezra Baruch ◽  
Michael Zimin
Keyword(s):  
Failure Analysis ◽  
Process Variations ◽  
Fault Isolation ◽  
Operating Conditions ◽  
Detection Sensitivity ◽  
Isolation Technique ◽  
Root Cause ◽  
Emission Microscopy ◽  
Failure Location ◽  
Noisy Background

Abstract Emission microscopy is usually implemented for static operating conditions of the DUT. Under dynamic operation it is nearly impossible to identify a failure out of the noisy background. In this paper we describe a simple technique that could be used in cases where the temporal location of the failure was identified however the physical location is not known or partially known. The technique was originally introduced to investigate IDDq failures (1) in order to investigate timing related issues with automated tester equipment. Ishii et al (2) improved the technique and coupled an emission microscope to the tester for functional failure analysis of DRAMs and logic LSIs. Using consecutive step-by-step tester halting coupled to a sensitive emission microscope, one is able detect the failure while it occurs. We will describe a failure analysis case in which marginal design and process variations combined to create contention at certain logic states. Since the failure occurred arbitrarily, the use of the traditional LVP, that requires a stable failure, misled the analysts. Furthermore, even if we used advanced tools as PICA, which was actually designed to locate such failures, we believe that there would have been little chance of observing the failure since the failure appeared only below 1.3V where the PICA tool has diminished photon detection sensitivity. For this case the step-by-step halting technique helped to isolate the failure location after a short round of measurements. With the use of logic simulations, the root cause of the failure was clear once the failing gate was known.

Yield and Failure Analysis of FinFET Source to Drain Leakage in 12nm Technology

2020 ◽  
Author(s):  
Felix Beaudoin ◽  
Satish Kodali ◽  
Rohan Deshpande ◽  
Wayne Zhao ◽  
Edmund Banghart ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Fault Localization ◽  
Detailed Characterization ◽  
Laser Stimulation ◽  
Emission Microscopy ◽  
Scan Chain ◽  
Multiple Samples ◽  
Tem Lamella ◽  
Diffusion Activation

Abstract Fault localization using both dynamic laser stimulation and emission microscopy was used to localize the failing transistors within the failing scan chain latch on multiple samples. Nanoprobing was then performed and the source to drain leakage in N-type FinFETs was identified. After extensive detailed characterization, it was concluded that the N-type dopant signal was likely due to projections from the source/drain regions included in the TEM lamella. Datamining identified the scan chain fail to be occurring uniquely for a specific family of tools used during source/drain implant diffusion activation. This paper discusses the processes involved in yield delta datamining of FinFET and its advantages over failure characterization, fault localization, nanoprobing, and physical failure analysis.

Creative Approach Using Lock-in Thermography in Fault Localization of ASIC Devices

2018 ◽  
Author(s):  
Andrew Sabate ◽  
Rommel Estores
Keyword(s):  
Low Power ◽  
Failure Analysis ◽  
Thermal Imaging ◽  
Fault Localization ◽  
Thermal Activity ◽  
Root Cause ◽  
Material Preparations ◽  
Imaging Application ◽  
Set Up ◽  
Lock In

Abstract The advent of lock-in thermal imaging application on semiconductor failure analysis added capability to localize failures through thermal activity (emission) of the die. When coupled with creative electrical set-up and material preparations, lock-in thermography (LIT) [1, 2] application gives more possibility in exploring the failure of the device using low power settings. This gives higher probability of preserving the defect which leads to a more conclusive root cause determination.

Sign in / Sign up

Export Citation Format

Share Document