Yield and Failure Analysis of FinFET Source to Drain Leakage in 12nm Technology

2020 ◽  
Author(s):  
Felix Beaudoin ◽  
Satish Kodali ◽  
Rohan Deshpande ◽  
Wayne Zhao ◽  
Edmund Banghart ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Fault Localization ◽  
Detailed Characterization ◽  
Laser Stimulation ◽  
Emission Microscopy ◽  
Scan Chain ◽  
Multiple Samples ◽  
Tem Lamella ◽  
Diffusion Activation

Abstract Fault localization using both dynamic laser stimulation and emission microscopy was used to localize the failing transistors within the failing scan chain latch on multiple samples. Nanoprobing was then performed and the source to drain leakage in N-type FinFETs was identified. After extensive detailed characterization, it was concluded that the N-type dopant signal was likely due to projections from the source/drain regions included in the TEM lamella. Datamining identified the scan chain fail to be occurring uniquely for a specific family of tools used during source/drain implant diffusion activation. This paper discusses the processes involved in yield delta datamining of FinFET and its advantages over failure characterization, fault localization, nanoprobing, and physical failure analysis.

Thermal Failure Analysis of Functional Failures by IR Lock-in Thermal Emission

2019 ◽  
Author(s):  
Paul Hubert P. Llamera ◽  
Camille Joyce G. Garcia-Awitan
Keyword(s):  
Integrated Circuits ◽  
Failure Analysis ◽  
Near Infrared ◽  
Thermal Emission ◽  
Fault Localization ◽  
Fault Isolation ◽  
Distinct Advantage ◽  
Infra Red ◽  
Emission Microscopy ◽  
Lock In

Abstract Lock-in thermography (LIT), known as a powerful nondestructive fault localization technique, can also be used for microscopic failure analysis of integrated circuits (ICs). The dynamic characteristic of LIT in terms of measurement, imaging and sensitivity, is a distinct advantage compared to other thermal fault localization methods as well as other fault isolation techniques like emission microscopy. In this study, LIT is utilized for failure localization of units exhibiting functional failure. Results showed that LIT was able to point defects with emissions in the mid-wave infra-red (MWIR) range that Photo Emission Microscopy (PEM) with near infrared (NIR) to short- wave infra-red (SWIR) detection wavelength sensitivity cannot to detect.

Advanced Fault Localization through the Use of Tester Based Diagnostics with LVI, LVP, CPA, and PEM

2013 ◽  
Author(s):  
Laura Safran ◽  
John Sylvestri ◽  
Dave Albert ◽  
Zhigang Song ◽  
Patrick McGinnis
Keyword(s):  
Technology Development ◽  
Photon Emission ◽  
Fault Localization ◽  
Parameter Analysis ◽  
Advanced Technology ◽  
Tem Analysis ◽  
Voltage Imaging ◽  
First Case ◽  
Emission Microscopy ◽  
Scan Chain

Abstract Fault localization on functional macros during advanced technology development requires a complex combination of tester based diagnostics and image based techniques including laser voltage imaging (LVI), laser voltage probing (LVP), critical parameter analysis (CPA) with laser stimulation and photon emission microscopy (PEM). These techniques are exemplified in the following three case studies. The first case involves a voltage sensitive SRAM block fail which was localized to a resistive via through the use of CPA, LVI and LVP. The second case demonstrates how a hard fail (a net-to-net metal short) in a scan chain was localized through use of tester based diagnostics, LVI, LVP and PEM. Finally, the last case shows how a condition sensitive failing latch chain was localized through CPA, LVI, LVP and PEM. Subsequent atomic force probing (AFP) identified source-drain leakage in one of the localized devices, and TEM analysis revealed a dislocation in the failing FET. Each of these cases demonstrates the value in utilizing tester based diagnostics along with laser based imaging and photon emission microscopy to localize failures.

Case Study: Combined Dynamic Laser Stimulation and Static Emission Microscopy Techniques Applied to Scan Test Failure on Mixed Mode Device

2012 ◽  
Author(s):  
Magdalena Sienkiewicz ◽  
Philippe Rousseille
Keyword(s):  
Mixed Mode ◽  
Laser Stimulation ◽  
Scan Test ◽  
Silicon Bulk ◽  
Defect Localization ◽  
Emission Microscopy ◽  
Microscopy Techniques ◽  
Test Failure

Abstract This paper presents a case study on scan test reject in a mixed mode IC. It focuses on the smart use of combined mature FA techniques, such as Soft Defect Localization (SDL) and emission microscopy (EMMI), to localize a random scan test anomaly at the silicon bulk level.

Advanced IR-OBIRCH Analysis Technique for High Isb Failure Analysis

2010 ◽  
Author(s):  
Kuo Hsiung Chen ◽  
Wen Sheng Wu ◽  
Yu Hsiang Shu ◽  
Jian Chan Lin
Keyword(s):  
Failure Analysis ◽  
Failure Mechanisms ◽  
Fault Localization ◽  
Resistance Change ◽  
The Real ◽  
Analysis Techniques ◽  
Analysis Technique ◽  
Leakage Failure ◽  
Failure Site

Abstract IR-OBIRCH (Infrared Ray – Optical Beam Induced Resistance Change) is one of the main failure analysis techniques [1] [2] [3] [4]. It is a useful tool to do fault localization on leakage failure cases such as poor Via or contact connection, FEoL or BEoL pattern bridge, and etc. But the real failure sites associated with the above failure mechanisms are not always found at the OBIRCH spot locations. Sometimes the real failure site is far away from the OBIRCH spot and it will result in inconclusive PFA Analysis. Finding the real failure site is what matters the most for fault localization detection. In this paper, we will introduce one case using deep sub-micron process generation which suffers serious high Isb current at wafer donut region. In this case study a BEoL Via poor connection is found far away from the OBIRCH spots. This implies that layout tracing skill and relation investigation among OBIRCH spots are needed for successful failure analysis.

Analysis of Delta Iddq Soft Fails on Pass Chips

2006 ◽  
Author(s):  
I. Österreicher ◽  
S. Eckl ◽  
B. Tippelt ◽  
S. Döring ◽  
R. Prang ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Failure Mode ◽  
Photon Emission ◽  
Complete Analysis ◽  
Functional Tests ◽  
Analysis Techniques ◽  
Atomic Force ◽  
Current Consumption ◽  
Emission Microscopy ◽  
Failure Localization

Abstract Depending on the field of application the ICs have to meet requirements that differ strongly from product to product, although they may be manufactured with similar technologies. In this paper a study of a failure mode is presented that occurs on chips which have passed all functional tests. Small differences in current consumption depending on the state of an applied pattern (delta Iddq measurement) are analyzed, although these differences are clearly within the usual specs. The challenge to apply the existing failure analysis techniques to these new fail modes is explained. The complete analysis flow from electrical test and Global Failure Localization to visualization is shown. The failure is localized by means of photon emission microscopy, further analyzed by Atomic Force Probing, and then visualized by SEM and TEM imaging.

Failure Analysis Enhancement by Incorporating a Compact Scan Diagnosis System

2014 ◽  
Author(s):  
Rommel Estores ◽  
Pascal Vercruysse ◽  
Karl Villareal ◽  
Eric Barbian ◽  
Ralph Sanchez ◽  
...  
Keyword(s):  
Data Analysis ◽  
Failure Analysis ◽  
Real Analysis ◽  
Failure Data ◽  
Analysis Methodology ◽  
Efficiency And Effectiveness ◽  
Scan Chain ◽  
On Chip ◽  
Analysis Environment ◽  
Selection Of

Abstract The failure analysis community working on highly integrated mixed signal circuitry is entering an era where simultaneously System-On-Chip technologies, denser metallization schemes, on-chip dissipation techniques and intelligent packages are being introduced. These innovations bring a great deal of defect accessibility challenges to the failure analyst. To contend in this era while aiming for higher efficiency and effectiveness, the failure analysis environment must undergo a disruptive evolution. The success or failure of an analysis will be determined by the careful selection of tools, data and techniques in the applied analysis flow. A comprehensive approach is required where hardware, software, data analysis, traditional FA techniques and expertise are complementary combined [1]. This document demonstrates this through the incorporation of advanced scan diagnosis methods in the overall analysis flow for digital functionality failures and supporting the enhanced failure analysis methodology. For the testing and diagnosis of the presented cases, compact but powerful scan test FA Lab hardware with its diagnosis software was used [2]. It can therefore easily be combined with the traditional FA techniques to provide stimulus for dynamic fault localizations [3]. The system combines scan chain information, failure data and layout information into one viewing environment which provides real analysis power for the failure analyst. Comprehensive data analysis is performed to identify failing cells/nets, provide a better overview of the failure and the interactions to isolate the fault further to a smaller area, or to analyze subtle behavior patterns to find and rationalize possible faults that are otherwise not detected. Three sample cases will be discussed in this document to demonstrate specific strengths and advantages of this enhanced FA methodology.

Failure Analysis of Killer Defects and Yield Enhancement of Flat ROM Devices in Wafer Fabrication

2000 ◽  
Author(s):  
Y. N. Hua ◽  
Z. R. Guo ◽  
L. H. An ◽  
Shailesh Redkar
Keyword(s):  
Electron Microscope ◽  
Failure Analysis ◽  
Fault Isolation ◽  
Yield Enhancement ◽  
Wafer Fabrication ◽  
X Ray ◽  
Particle Contamination ◽  
Emission Microscopy ◽  
Microscopy Techniques ◽  
Scanning Electron

Abstract In this paper, some low yield cases in Flat ROM device (0.45 and 0.6 µm) were investigated. To find killer defects and particle contamination, KLA, bitmap and emission microscopy techniques were used in fault isolation. Reactive ion etching (RIE) and chemical delayering, 155 Wright Etch, BN+ Etch and scanning electron microscope (SEM) were used for identification and inspection of defects. In addition, energy-dispersive X-ray microanalysis (EDX) was used to determine the composition of the particle or contamination. During failure analysis, seven kinds of killer defects and three killer particles were found in Flat ROM devices. The possible root causes, mechanisms and elimination solutions of these killer defects/particles were also discussed.

A Sample Preparation on Decapsulation Methodology for Effective Failure Analysis on Thin Small Leadless (TSLP) Flip Chip Package with Copper Pillar (CuP) Bump Interconnect Technology

2014 ◽  
Author(s):  
Gwee Hoon Yen ◽  
Ng Kiong Kay
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Flip Chip ◽  
Fault Localization ◽  
Cost Effective ◽  
Fault Isolation ◽  
Voltage Contrast ◽  
Interconnect Technology

Abstract Today, failure analysis involving flip chip [1] with copper pillar bump packaging technologies would be the major challenges faced by analysts. Most often, handling on the chips after destructive chemical decapsulation is extremely critical as there are several failure analysis steps to be continued such as chip level fault localization, chip micro probing for fault isolation, parallel lapping [2, 3, 4] and passive voltage contrast. Therefore, quality of sample preparation is critical. This paper discussed and demonstrated a quick, reliable and cost effective methodology to decapsulate the thin small leadless (TSLP) flip chip package with copper pillar (CuP) bump interconnect technology.

SRAM Failure Analysis Strategy

2003 ◽  
Author(s):  
P. Egger ◽  
C. Burmer
Keyword(s):  
Liquid Crystal ◽  
Failure Analysis ◽  
The Other ◽  
Other Hand ◽  
Analysis Strategy ◽  
Emission Microscopy ◽  
Metal Layers ◽  
Failure Localization

Abstract The area of embedded SRAMs in advanced logic ICs is increasing more and more. On the other hand smaller structure sizes and an increasing number of metal layers make conventional failure localization by using emission microscopy or liquid crystal inefficient. In this paper a SRAM failure analysis strategy will be presented independent on layout and technology.

High-Throughput, Site-Specific Sample Prep of Ultra-Thin TEM Lamella for Process Metrology and Failure Analysis

2012 ◽  
Author(s):  
Roger Alvis ◽  
Jeff Blackwood ◽  
Sang-Hoon Lee ◽  
Matthew Bray
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Process Monitoring ◽  
High Throughput ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Memory Devices ◽  
Site Specific ◽  
Critical Dimensions ◽  
Tem Lamella

Abstract Semiconductor devices with critical dimensions less than 20nm are now being manufactured in volume. A challenge facing the failure analysis and process-monitoring community is two-fold. The first challenge of TEM sample prep of such small devices is that the basic need to end-point on a feature-of-interest pushes the imaging limit of the instrument being used to prepare the lamella. The second challenge posed by advanced devices is to prepare an artifact-free lamella from non-planar devices such as finFETs as well as from structures incorporating ‘non-traditional’ materials. These challenges are presently overcome in many advanced logic and memory devices in the focused ion beam-based TEM sample preparation processes by inverting the specimen prior to thinning to electron transparency. This paper reports a highthroughput method for the routine preparation of artifact-free TEM lamella of 20nm thickness, or less.

Sign in / Sign up

Export Citation Format

Share Document