scholarly journals Geopolymer-Bonded Laminated Veneer Lumber as Environmentally Friendly and Formaldehyde-Free Product: Effect of Various Additives on Geopolymer Binder Features

2020 ◽  
Vol 10 (2) ◽  
pp. 593 ◽  
Author(s):  
Ali Shalbafan ◽  
Heiko Thoemen
Keyword(s):  
Mechanical Properties ◽  
Silica Fume ◽  
Positive Impact ◽  
Environmentally Friendly ◽  
Gel Time ◽  
Scanning Calorimetry ◽  
Bonding Quality ◽  
Laminated Veneer Lumber ◽  
Geopolymer Binder ◽  
Shear Bending

Environmentally friendly and formaldehyde-free laminated veneer lumber (LVL) was manufactured using geopolymer constituents as binder. The main aim of the study was to improve the bonding quality between the geopolymer binder and the wood constituents. To this end, the effect of various additives (phenol flakes, conventional silica fume, and grafted silica fume with 3-aminopropyltriethoxysilane (APTES)) in the geopolymer binder features were explored via gel time and viscosity measurements, differential scanning calorimetry (DSC), and Fourier transom infrared spectroscopy. The mechanical properties (shear, bending, and compression) of LVL panels were also determined. Results showed that adding both types of silica fume had a positive impact on the geopolymer binder features. The formation of an alkaline aluminosilicate network was proven by observing the characteristics peaks of geopolymer binder at about 683 and 970 cm−1. A peak temperature of about 98 °C was determined for the geopolymer binder curing via DSC analysis. The mechanical properties were the highest for LVL panels made of geopolymer binder with grafted silica fume. It is feasible that the APTES used as grafting agent created a better bonding mechanism with superficial wood cells. In summary, the produced LVL panel showed good properties, but it still needs to be further improved to reach the required levels for use in interior and humid application.

scholarly journals Properties of Plywood Produced with Urea-Formaldehyde Adhesive Modified with Nanocellulose and Microcellulose

2020 ◽  
Vol 71 (1) ◽  
pp. 61-67 ◽  
Author(s):  
Jakub Kawalerczyk ◽  
Dorota Dziurka ◽  
Radosław Mirski ◽  
Kinga Szentner
Keyword(s):  
Mechanical Properties ◽  
Modulus Of Elasticity ◽  
Urea Formaldehyde ◽  
Rheological Behaviour ◽  
Formaldehyde Emission ◽  
Solid Content ◽  
Curing Process ◽  
Gel Time ◽  
Bonding Quality ◽  
Adhesive Mixtures

Urea-formaldehyde adhesives are widely used in the wood-based materials industry. The study investigates the possibility of using cellulosic particles as a filler that modifies the properties of the resin and consequently improves the properties of plywood. Moreover, the study also examines the differences between microcellulose and nanocellulose used as a filler for UF adhesive. Based on the investigations, it was found that the addition of MFC and NCC significantly affected the curing process and rheological behaviour of adhesive mixtures. Modification led to increase of viscosity and extension of a gel time caused by lowering solid content of the resin. The experimental and reference plywood were tested in terms of bonding quality and mechanical properties such as modulus of elasticity and modulus of rigidity in accordance with applicable standards. The results of the tests confirmed that both the amount and the type of modifier added to the resin had a significant effect on the properties of plywood. The bonding quality and the above mentioned mechanical properties improved in all variants of modification; however the most effective was the addition of NCC in the amount of 10 %/100 g of solid resin. The slight decrease of formaldehyde emission was only observed for 5 % cellulosic particles added to 100 g of solid UF.

Effect of waste electronic plastic and silica fume on mechanical properties and thermal performance of concrete

2021 ◽  
Vol 285 ◽  
pp. 122952
Author(s):  
Khawar Ali ◽  
Muhammad Irshad Qureshi ◽  
Shahzad Saleem ◽  
Sibghat Ullah Khan
Keyword(s):  
Mechanical Properties ◽  
Silica Fume ◽  
Thermal Performance

Mechanical properties of ternary blended mix concrete of fly ash and silica fume

2021 ◽  
Author(s):  
Anjaneya Babu Padavala ◽  
Malasani Potharaju ◽  
Venkata Ramesh Kode
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Silica Fume

scholarly journals Relationship between the Stereocomplex Crystallization Behavior and Mechanical Properties of PLLA/PDLA Blends

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1851
Author(s):  
Hye-Seon Park ◽  
Chang-Kook Hong
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Crystallization Behavior ◽  
Mechanical Analysis ◽  
X Ray Diffraction ◽  
Nucleation Agent ◽  
Scanning Calorimetry ◽  
Nucleation Sites ◽  
Wide Range ◽  
Degree Of Crystallization

Poly (l-lactic acid) (PLLA) is a promising biomedical polymer material with a wide range of applications. The diverse enantiomeric forms of PLLA provide great opportunities for thermal and mechanical enhancement through stereocomplex formation. The addition of poly (d-lactic acid) (PDLA) as a nucleation agent and the formation of stereocomplex crystallization (SC) have been proven to be an effective method to improve the crystallization and mechanical properties of the PLLA. In this study, PLLA was blended with different amounts of PDLA through a melt blending process and their properties were calculated. The effect of the PDLA on the crystallization behavior, thermal, and mechanical properties of PLLA were investigated systematically by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), polarized optical microscopy (POM), dynamic mechanical analysis (DMA), and tensile test. Based on our findings, SC formed easily when PDLA content was increased, and acts as nucleation sites. Both SC and homo crystals (HC) were observed in the PLLA/PDLA blends. As the content of PDLA increased, the degree of crystallization increased, and the mechanical strength also increased.

scholarly journals Effect of Multiple Reflows on the Interfacial Reactions and Mechanical Properties of an Sn-0.5Cu-Al(Si) Solder and a Cu Substrate

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2367
Author(s):  
Junhyuk Son ◽  
Dong-Yurl Yu ◽  
Yun-Chan Kim ◽  
Shin-Il Kim ◽  
Min-Su Kim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Heat ◽  
Interfacial Reactions ◽  
Future Application ◽  
Scanning Calorimetry ◽  
Cross Sectional ◽  
Automotive Electronic ◽  
Transmission Electron ◽  
Si Content ◽  
Lead Free Solders

In this study, the interfacial reactions and mechanical properties of solder joints after multiple reflows were observed to evaluate the applicability of the developed materials for high-temperature soldering for automotive electronic components. The microstructural changes and mechanical properties of Sn-Cu solders regarding Al(Si) addition and the number of reflows were investigated to determine their reliability under high heat and strong vibrations. Using differential scanning calorimetry, the melting points were measured to be approximately 227, 230, and 231 °C for the SC07 solder, SC-0.01Al(Si), and SC-0.03Al(Si), respectively. The cross-sectional analysis results showed that the total intermetallic compounds (IMCs) of the SC-0.03Al(Si) solder grew the least after the as-reflow, as well as after 10 reflows. Electron probe microanalysis and transmission electron microscopy revealed that the Al-Cu and Cu-Al-Sn IMCs were present inside the solders, and their amounts increased with increasing Al(Si) content. In addition, the Cu6Sn5 IMCs inside the solder became more finely distributed with increasing Al(Si) content. The Sn-0.5Cu-0.03Al(Si) solder exhibited the highest shear strength at the beginning and after 10 reflows, and ductile fracturing was observed in all three solders. This study will facilitate the future application of lead-free solders, such as an Sn-Cu-Al(Si) solder, in automotive electrical components.

Effect of toughened polyamide-coated carbon fiber fabric on the mechanical performance and fracture toughness of CFRP

2021 ◽  
pp. 002199832199945
Author(s):  
Jong H Eun ◽  
Bo K Choi ◽  
Sun M Sung ◽  
Min S Kim ◽  
Joon S Lee
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Photoelectron Spectroscopy ◽  
Mechanical Performance ◽  
Epoxy Composites ◽  
Scanning Calorimetry ◽  
Internal Damage ◽  
Impact Tests ◽  
Flexural Tests ◽  
The Impact

In this study, carbon/epoxy composites were manufactured by coating with a polyamide at different weight percentages (5 wt.%, 10 wt.%, 15 wt.%, and 20 wt.%) to improve their impact resistance and fracture toughness. The chemical reaction between the polyamide and epoxy resin were examined by fourier transform infrared spectroscopy, differential scanning calorimetry and X-ray photoelectron spectroscopy. The mechanical properties and fracture toughness of the carbon/epoxy composites were analyzed. The mechanical properties of the carbon/epoxy composites, such as transverse flexural tests, longitudinal flexural tests, and impact tests, were investigated. After the impact tests, an ultrasonic C-scan was performed to reveal the internal damage area. The interlaminar fracture toughness of the carbon/epoxy composites was measured using a mode I test. The critical energy release rates were increased by 77% compared to the virgin carbon/epoxy composites. The surface morphology of the fractured surface was observed. The toughening mechanism of the carbon/epoxy composites was suggested based on the confirmed experimental data.

scholarly journals Effects of Aging under Stress on Mechanical Properties and Microstructure of EN AW 7075 Alloy

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1142
Author(s):  
S. V. Sajadifar ◽  
P. Krooß ◽  
H. Fröck ◽  
B. Milkereit ◽  
O. Kessler ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Screening Tool ◽  
Precipitation Kinetics ◽  
Scanning Calorimetry ◽  
Aging Precipitation ◽  
Precipitation Processes ◽  
External Stresses ◽  
7075 Alloy ◽  
Effects Of Aging

In the present study, microstructural and mechanical properties of EN AW 7075 following stress-aging were assessed. For this purpose, properties of stress-aged samples were compared with values obtained for conventionally aged counterparts. It is revealed that the strength and hardness of EN AW 7075 can be increased by the presence of external stresses during aging. Precipitation kinetics were found to be accelerated. The effects of conventional and stress-aging on the microstructure were analyzed using synergetic techniques: the differently aged samples were probed by differential scanning calorimetry (DSC) in order to characterize the precipitation processes. DSC was found to be an excellent screening tool for the analysis of precipitation processes during aging of this alloy with and without the presence of external stresses. Furthermore, using electron microscopy it was revealed that an improvement in mechanical properties can be correlated to changes in the morphologies and sizes of precipitates formed.

scholarly journals Effects of Sintering Temperature on Densification, Microstructure and Mechanical Properties of Al-Based Alloy by High-Velocity Compaction

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 218
Author(s):  
Xianjie Yuan ◽  
Xuanhui Qu ◽  
Haiqing Yin ◽  
Zaiqiang Feng ◽  
Mingqi Tang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Velocity ◽  
Sintered Density ◽  
Sintering Temperature ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
High Velocity Compaction ◽  
Sintered Temperature

This present work investigates the effects of sintering temperature on densification, mechanical properties and microstructure of Al-based alloy pressed by high-velocity compaction. The green samples were heated under the flow of high pure (99.99 wt%) N2. The heating rate was 4 °C/min before 315 °C. For reducing the residual stress, the samples were isothermally held for one h. Then, the specimens were respectively heated at the rate of 10 °C/min to the temperature between 540 °C and 700 °C, held for one h, and then furnace-cooled to the room temperature. Results indicate that when the sintered temperature was 640 °C, both the sintered density and mechanical properties was optimum. Differential Scanning Calorimetry, X-ray diffraction of sintered samples, Scanning Electron Microscopy, Energy Dispersive Spectroscopy, and Transmission Electron Microscope were used to analyse the microstructure and phases.

scholarly journals Halloysite Nanotubes and Silane-Treated Alumina Trihydrate Hybrid Flame Retardant System for High-Performance Cable Insulation

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2134
Author(s):  
Sandra Paszkiewicz ◽  
Izabela Irska ◽  
Iman Taraghi ◽  
Elżbieta Piesowicz ◽  
Jakub Sieminski ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polymer Blend ◽  
Hybrid System ◽  
Reference Sample ◽  
Melt Flow Index ◽  
Halloysite Nanotubes ◽  
Flow Index ◽  
Scanning Calorimetry ◽  
Limiting Oxygen Index ◽  
Alumina Trihydrate

The effect of the presence of halloysite nanotubes (HNTs) and silane-treated alumina trihydrate (ATH-sil) nanofillers on the mechanical, thermal, and flame retardancy properties of ethylene-vinyl acetate (EVA) copolymer/low-density polyethylene (LDPE) blends was investigated. Different weight percentages of HNT and ATH-sil nanoparticles, as well as the hybrid system of those nanofillers, were melt mixed with the polymer blend (reference sample) using a twin-screw extruder. The morphology of the nanoparticles and polymer compositions was studied using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The mechanical properties, hardness, water absorption, and melt flow index (MFI) of the compositions were assessed. The tensile strength increases as a function of the amount of HNT nanofiller; however, the elongation at break decreases. In the case of the hybrid system of nanofillers, the compositions showed superior mechanical properties. The thermal properties of the reference sample and those of the corresponding sample with nanofiller blends were studied using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Two peaks were observed in the melting and crystallization temperatures. This shows that the EVA/LDPE is an immiscible polymer blend. The thermal stability of the blends was improved by the presence of HNTs and ATH-sil nanoparticles. Thermal degradation temperatures were shifted to higher values by the presence of hybrid nanofillers. Finally, the flammability of the compositions was assessed. Flammability as reflected by the limiting oxygen index (OI) was increased by the presence of HNT and ATH-sil nanofiller and a hybrid system of the nanoparticles.

Sign in / Sign up

Export Citation Format

Share Document