scholarly journals Exploring the Bioethanol Production Potential of Miscanthus Cultivars

2021 ◽  
Vol 11 (21) ◽  
pp. 9949
Author(s):  
William Turner ◽  
Darren Greetham ◽  
Michal Mos ◽  
Michael Squance ◽  
Jason Kam ◽  
...  
Keyword(s):  
Perennial Grass ◽  
Dry Weight ◽  
Lignocellulose Degradation ◽  
Bioethanol Production ◽  
Glucose Content ◽  
Sugar Release ◽  
Growing Period ◽  
Miscanthus Giganteus ◽  
The Difference ◽  
Pre Treatment

Miscanthus is a fast-growing perennial grass that attracts significant attention for its potential application as a feedstock for bioethanol production. This report explores the difference in the lignocellulosic composition of various Miscanthus cultivars, including Miscanthus × giganteus cultivated at the same location (mainly Lincoln, UK). It also assesses the sugar release profiles and mineral composition profiles of five Miscanthus cultivars harvested over a growing period from November 2018 to February 2019. The results showed that Miscanthus × giganteus contains approximately 45.5% cellulose, 29.2% hemicellulose and 23.8% lignin (dry weight, w/w). Other cultivars of Miscanthus also contain high quantities of carbohydrates (cellulose 41.1–46.0%, hemicellulose 24.3–32.6% and lignin 21.4–24.9%). Pre-treatment of Miscanthus using dilute acid followed by enzymatic hydrolysis released 63.7–80.2% of the theoretical glucose content. Fermentation of a hydrolysate of Miscanthus × giganteus using Saccharomyces cerevisiae NCYC2592 produced 13.58 ± 1.11 g/L of ethanol from 35.13 ± 0.46 g/L of glucose, corresponding to a yield of 0.148 g/g dry weight Miscanthus biomass. Scanning electron microscopy was used to study the morphology of raw and hydrolysed Miscanthus samples, which provided visual proof of Miscanthus lignocellulose degradation in these processes. The sugar release profile showed that a consequence of Miscanthus plant growth is an increase in difficulty in releasing monosaccharides from the biomass. The potassium, magnesium, sodium, sulphur and phosphorus contents in various Miscanthus cultivars were analysed. The results revealed that these elements were slowly lost from the plants during the latter part of the growing season, for a specific cultivar, until February 2019.

scholarly journals Assessment of an Impact of Mechanical Regulation on Selected Morphometric and Productive Parameters of Invasive Species Solidago Canadensis Population in Agricultural Land

2015 ◽  
Vol 61 (4) ◽  
pp. 121-128
Author(s):  
Lýdia Končeková ◽  
Eva Zahradníková ◽  
Eduard Pintér ◽  
Daniela Halmová
Keyword(s):  
Agricultural Land ◽  
Dry Weight ◽  
Effective Control ◽  
Solidago Canadensis ◽  
Growing Period ◽  
Anthropogenic Habitat ◽  
The Difference ◽  
The Impact ◽  
Number Of Individuals ◽  
Mechanical Regulation

Abstract Repeated mowing is considered as one of the effective control methods against species of the genus Solidago. This paper evaluates the impact of the repeated mowing on selected morphometric and productive characteristics of the invasive neophyte Solidago canadensis in the district of Rimavská Sobota in Central Slovakia. Permanent research plots (PRPs) were established within anthropogenic habitat on an abandoned land that was divided into two variants. In the first variant, the mechanical regulation - mowing was applied. The second variant was without the regulation. The mechanical regulation of the populations was carried out in June and August during the growing season 2011. The results showed that the mechanical regulation did not have a clear impact on the population density. The decreasing trend of the number of shoots within the mowed variant was found only in one research plot (PRP3). The other plots showed an increase in the number of individuals by 2.7 and 32.7% between the mowings. Statistically highly significant differences in terms of the mowing impact on the height of the individuals were found in all PRPs. The difference in the weight of dry aboveground biomass between the mowings was 221.87 g, which represents 36.41%. Double the difference (48.8%) was recorded in the dry weight of the underground biomass in the regulated stand compared with the unregulated stand (165.1 and 322.5 g/m2, respectively). Although there was a short-term success achieved by the application of the two mowings during the growing period, the pursued objective was not reached.

scholarly journals Application of lignocellulolytic fungi for bioethanol production from renewable biomass

2015 ◽  
Vol 69 (6) ◽  
pp. 627-641 ◽  
Author(s):  
Jelena Jovic ◽  
Jelena Pejin ◽  
Suncica Kocic-Tanackov ◽  
Ljiljana Mojovic
Keyword(s):  
White Rot Fungi ◽  
Alcohol Oxidase ◽  
Brown Rot ◽  
White Rot ◽  
Lignocellulose Degradation ◽  
Bioethanol Production ◽  
Decay Fungi ◽  
Advantages And Disadvantages ◽  
Wide Range ◽  
Pre Treatment

Pretreatment is a necessary step in the process of conversion of lignocellulosic biomass to ethanol; by changing the structure of lignocellulose, enhances enzymatic hydrolysis, but, often, it consumes large amounts of energy and/or needs an application of expensive and toxic chemicals, which makes the process economically and ecologically unfavourable. Application of lignocellulolytic fungi (from the class Ascomycetes, Basidiomycetes and Deuteromycetes) is an attractive method for pre-treatment, environmentally friendly and does not require the investment of energy. Fungi produce a wide range of enzymes and chemicals, which, combined in a variety of ways, together successfully degrade lignocellulose, as well as aromatic polymers that share features with lignin. On the basis of material utilization and features of a rotten wood, they are divided in three types of wood-decay fungi: white rot, brown rot and soft rot fungi. White rot fungi are the most efficient lignin degraders in nature and, therefore, have a very important role in carbon recycling from lignified wood. This paper describes fungal mechanisms of lignocellulose degradation. They involve oxidative and hydrolytic mechanisms. Lignin peroxidase, manganese peroxidase, laccase, cellobiose dehydrogenase and enzymes able to catalyze formation of hydroxyl radicals (?OH) such as glyoxal oxidase, pyranose-2-oxidase and aryl-alcohol oxidase are responsible for oxidative processes, while cellulases and hemicellulases are involved in hydrolytic processes. Throughout the production stages, from pre-treatment to fermentation, the possibility of their application in the technology of bioethanol production is presented. Based on previous research, the advantages and disadvantages of biological pre-treatment are pointed out.

The yield of perennial grass stands on drained organic soils of Steppe

2016 ◽  
Vol 1 (90) ◽  
pp. 92-97
Author(s):  
I.T. Slusar ◽  
V.A. Serbenyuk ◽  
A.N. Gera ◽  
A.P. Solyanik ◽  
A.A. Tarasenko
Keyword(s):  
Zinc Sulphate ◽  
Foliar Application ◽  
Perennial Grass ◽  
Mineral Fertilizer ◽  
Dry Weight ◽  
Research Area ◽  
Organic Soils ◽  
Growth Promoters ◽  
Cobalt Sulfate ◽  
The Impact

Research on the impact of the introduction of micro fertilizers and growth promoters on a background of mineral fertilizer and without N90R45К120 spent on old peat in shallow carbonate floodplain r.Supiy, Yahotyn Kyiv region. Power peat horizon about 60-70 cm, 7,4-7,6 pH of the aqueous extract, stupas schedule 56-60%, density 0,49-0,52 assembly soil, total nitrogen content (%) - 1.9; gross forms of phosphorus - 0,4, potassium 0.2, 20% lime. In experiments studying biological rehoplant, radustym, Biolan, emistim, Jets, humisol, plantafol, radyfarm and micronutrients: copper, boric acid, manganese sulphate, zinc sulphate, potassium humates. Treatment drugs conducted in the spring by spraying mixtures. Space research area of 60 m2, three-time repetition. It is established that the use of growth stimulants and micronutrients in the background N90R45К120 provided the highest yield mixtures of years, against making BIOLan - 9.9 t / ha Radyfarmu - 9.6 t / ha Radostymu 9.3 t / ha dry weight. In areas for making other preparations were intermediate yield growth rates - 0.5 - 2.0 t / ha dry weight. Also good gains herbage yields obtained by making all kinds of micronutrients and growth stimulants in the background without making makrodobryv which was within 5.3 - 6.9 t / ha to control without fertilization - 4.5 t / ha dry weight. In deep peat copper fertilizer (25 kg / ha of copper sulphate or 5 kg / ha pirytnoho cinders) in all zones should be making every 3-4 years, and zinc, cobalt and molybdenum advisable to make time for the growing season, spring, by foliar application in such numbers: ammonium molibdenovokyslyy - 0.3 kg / ha; cobalt sulfate - 3 kg / ha zinc sulphate 0.5 kg / ha or placers these salts should be mixed with major fertilizer.

Purification of Pisciculture Waters through Cultivation and Harvesting of Aquatic Biomass

1987 ◽  
Vol 19 (10) ◽  
pp. 113-121 ◽  
Author(s):  
C. Simeon ◽  
M. Silhol
Keyword(s):  
Aquatic Macrophyte ◽  
Dry Weight ◽  
Final Decision ◽  
Effluent Water ◽  
Aquatic Biomass ◽  
Growing Period ◽  
European Climate ◽  
Nuclear Plants ◽  
Economical Optimization ◽  
Water Hyacinths

The study of thermal wastes from the nuclear plants around Pierrelatte for agricultural, piscicultural, energy and environmental protection purposes resulted in the establishment of a pilot facility as early as 1976. An aquatic macrophyte pilot facility has been operational since 1983 to study the use of water hyacinths from the aspects of energy and ecology. The results obtained suggest that production yields for the 7 month growing period should exceed 60 metric tons (MT) (dry weight) per hectare in a European climate, and that such crops can feasibly be cultivated in temperate regions. The pilot facility is supplied with pisciculture effluent water, making it possible to quantify the stabilization power of the plants. Without primary decantation, with a retention time of 4 days and stabilization with water hyacinths only, the organic matter waste pond surface area required is 3.5 m2/m2 of pisciculture pond. Any primary or secondary facilities will lead to a reduction of these areas. The final decision will depend on the economical optimization of all the wastewater.

scholarly journals Influence of the Bottom Color Modification and Material Color Modification Process on the Performance of Modified Poplar

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 660
Author(s):  
Qingqing Liu ◽  
Di Gao ◽  
Wei Xu
Keyword(s):  
Chemical Properties ◽  
Target Color ◽  
Modification Process ◽  
Red Color ◽  
The Difference ◽  
Pre Treatment ◽  
Physical And Chemical ◽  
Surface Differentiation ◽  
Color Modification ◽  
And Chemical Properties

According to the old surface coating process of European and American furniture, the surface of modified poplar is first differentiated pre-treatment, and then the bottom color modification and material color modification are respectively applied to the modified poplar after the surface differentiation treatment. The visual physical quantity and physical and chemical properties were measured and compared with mahogany, which is commonly used in old furniture in Europe and America to explore the effect of colorants and coloring steps, as well as different surface pretreatments on the coloring effect. Finally, it is concluded that continuous coloring operations can narrow the difference in brightness and red color value in the coloring layer of modified poplar and mahogany. Continuous coloring operations increase the difference between the yellow-green color values of modified poplar and mahogany. Therefore, the coloring difference between modified poplar and mahogany was affected by the colorant and coloring steps. Through color accumulation, the gap between the two in the target color coloring effect can be reduced, thereby reducing the difference between the coloring effect of modified poplar and mahogany.

scholarly journals Vegetative and Reproductive Response to Fruit Load in Two Jojoba (Simmondsia chinensis) Cultivars

Agronomy ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 889
Author(s):  
Aviad Perry ◽  
Noemi Tel-Zur ◽  
Arnon Dag
Keyword(s):  
Vegetative Growth ◽  
Accumulation Rate ◽  
Dry Weight ◽  
High Yield ◽  
Lower Amount ◽  
Simmondsia Chinensis ◽  
Alternate Bearing ◽  
Fruit Removal ◽  
Growing Period ◽  
Fruit Load

Jojoba (Simmondsia chinensis) is a wax crop cultivated mainly in arid and semi-arid regions. This crop has been described as an alternate-bearing plant, meaning that it has a high-yield year (“on-year”) followed by a low-yield year (“off-year”). We investigated the effect of fruit load on jojoba’s vegetative and reproductive development. For two consecutive years, we experimented with two high-yielding cultivars—Benzioni and Hazerim—which had opposite fruit loads, i.e., one was under an on-year load, while the other was under an off-year load simultaneously. We found that removing the developing fruit from the shoot during an off-year promotes further vegetative growth in the same year, whereas in an on-year, this action has no effect. Moreover, after fruit removal in an on-year, there was a delay in vegetative growth renewal in the consecutive year, suggesting that the beginning of the growing period is dependent on the previous year’s yield load. We found that seed development in the 2018 season started a month earlier than in the 2017 season in both cultivars, regardless of fruit load. This early development was associated with higher wax content in the seeds. Hence, the wax accumulation rate, as a percentage of dry weight, was affected by year and not by fruit load. However, on-year seeds stopped growing earlier than off-year seeds, resulting in smaller seeds and an overall lower amount of wax per seed.

scholarly journals Assessment of the papermaking potential of processed Miscanthus × giganteus stalks using alkaline pre-treatment and hydrodynamic cavitation for delignification

2021 ◽  
Vol 72 ◽  
pp. 105462
Author(s):  
Dimitrios Tsalagkas ◽  
Zoltán Börcsök ◽  
Zoltán Pásztory ◽  
Parag Gogate ◽  
Levente Csóka
Keyword(s):  
Hydrodynamic Cavitation ◽  
Miscanthus Giganteus ◽  
Pre Treatment

Temperature dependence of germinability of wheat (Triticum aestivum L.) grain in relation to pre-harvest sprouting

1984 ◽  
Vol 35 (2) ◽  
pp. 115 ◽  
Author(s):  
DJ Mares
Keyword(s):  
Dry Weight ◽  
Complete Removal ◽  
Triticum Aestivum L ◽  
Treatment Temperature ◽  
Preharvest Sprouting ◽  
Optimum Temperature ◽  
Grain Dormancy ◽  
Lag Period ◽  
Pre Treatment ◽  
Damage Tolerant

Germinability in harvest-mature wheat grain showed a marked dependence on temperature. The optimum temperature for the complete germination of all grains ranged from 20�C for the non-dormant variety, Timgalen, to 10�C for the strongly dormant red wheat RL 4137, whereas the optimum in terms of the shortest lag period ranged from 25� to 15�C for the same varieties. Germinability gradually increased during post-harvest storage and, for after-ripened grain, the optimum temperature for both complete germination and shortest lag period were greater than 30�C. Germinability could also be increased by pre-treating imbibing grains at temperatures of 5�, 10� or in some cases 15�C. This treatment was only effective for grain at moisture contents >25% (dry weight) and the effect was not reversed by redesiccation. The pre-treatment temperature required for maximum germinability decreased with increasing levels of grain dormancy. Complete removal of dormancy required a pre-treatment period of c. 48 h; however, lesser periods gave the shortest lag period in the case of the dormant varieties. The implications of these results for the utilization of dormancy in the development of preharvest sprouting damage tolerant varieties and their subsequent use in practice are discussed.

scholarly journals Plant uptake of nitrogen adsorbed to biochars made from dairy manure

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Leilah Krounbi ◽  
Akio Enders ◽  
John Gaunt ◽  
Margaret Ball ◽  
Johannes Lehmann
Keyword(s):  
New York ◽  
Crop Production ◽  
Liquid Fraction ◽  
N Uptake ◽  
Dry Weight ◽  
Dairy Manure ◽  
Production Costs ◽  
Available N ◽  
Dairy Waste ◽  
Pre Treatment

AbstractThe conversion of dairy waste with high moisture contents to dry fertilizers may reduce environmental degradation while lowering crop production costs. We converted the solid portion of screw-pressed dairy manure into a sorbent for volatile ammonia (NH3) in the liquid fraction using pyrolysis and pre-treatment with carbon dioxide (CO2). The extractable N in manure biochar exposed to NH3 following CO2 pre-treatment reached 3.36 g N kg−1, 1260-fold greater extractable N than in untreated manure biochar. Ammonia exposure was 142-times more effective in increasing extractable N than immersing manure biochar in the liquid fraction containing dissolved ammonium. Radish and tomato grown in horticultural media with manure biochar treated with CO2 + NH3 promoted up to 35% greater plant growth (dry weight) and 36–83% greater N uptake compared to manure biochar alone. Uptake of N was similar between plants grown with wood biochar exposed to CO2 + NH3, compared to N-equivalent treatments. The available N in dairy waste in New York (NY) state, if pyrolyzed and treated with NH3 + CO2, is equivalent to 11,732–42,232 Mg N year−1, valued at 6–21.5 million USD year−1. Separated dairy manure treated with CO2 + NH3 can offset 23–82% of N fertilizer needs of NY State, while stabilizing both the solid and liquid fraction of manure for reduced environmental pollution.

Sign in / Sign up

Export Citation Format

Share Document