scholarly journals A Study on the Removal of Copper (II) from Aqueous Solution Using Lime Sand Bricks

2019 ◽  
Vol 9 (4) ◽  
pp. 670 ◽  
Author(s):  
Xiaoran Zhang ◽  
Shimin Guo ◽  
Junfeng Liu ◽  
Ziyang Zhang ◽  
Kaihong Song ◽  
...  
Keyword(s):  
Residence Time ◽  
Removal Rate ◽  
Low Cost ◽  
Column Experiment ◽  
Residual Fraction ◽  
Maximum Adsorption Capacity ◽  
Copper Adsorption ◽  
Exchangeable Fraction ◽  
Pseudo Second Order ◽  
Stormwater Infiltration

Heavy metals such as Cu(II), if ubiquitous in the runoff, can have adverse effects on the environment and human health. Lime sand bricks, as low-cost adsorbents to be potentially applied in stormwater infiltration facilities, were systematically investigated for Cu(II) removal from water using batch and column experiments. In the batch experiment, the adsorption of Cu(II) to bricks reach an equilibrium within 7 h and the kinetic data fits well with the pseudo-second-order model. The sorption isotherm can be described by both the Freundlich and Langmuir model and the maximum adsorption capacity of the bricks is 7 ± 1 mg/g. In the column experiment, the best removal efficiency for Cu(II) was observed at a filler thickness of 20 cm, service time of 12 min with a Cu(II) concentration of 0.5 mg/L. The Cu(II) removal rate increases with the increasing bed depth and residence time. The inlet concentration and residence time had significant effects on the Cu(II) removal analyzed by the Box–Behnken design (BBD). The Adams-Bohart model was in good agreement with the experimental data in representing the breakthrough curve. Copper fractions in the bricks descend in the order of organic matter fraction > Fe-Mn oxides fraction > carbonates fraction > residual fraction > exchangeable fraction, indicating that the lime sand bricks after copper adsorption reduce the long-term ecotoxicity and bioavailability to the environment.

scholarly journals Adsorption of copper ions on Magnolia officinalis residues after solid-phase fermentation with Phanerochaete chrysosporium

2019 ◽  
Vol 17 (1) ◽  
pp. 1173-1184 ◽  
Author(s):  
Fengyun Tao ◽  
Yangping Liu ◽  
Junliang Chen ◽  
Peng Wang ◽  
Qing Huo
Keyword(s):  
Chinese Medicine ◽  
Phanerochaete Chrysosporium ◽  
Solid Phase ◽  
Copper Ions ◽  
Removal Rate ◽  
Low Cost ◽  
Preparation Technique ◽  
Adsorption Enthalpy ◽  
Pseudo Second Order ◽  
Magnolia Officinalis

AbstractThe disposal of residues while manufacturing Chinese medicine has always been an issue that concerns pharmaceutical factories. Phanerochaete chrysosporium was inoculated into the residues of Magnolia officinalis for solid-phase fermentation to enzymatically hydrolyze the lignin in the residues and thus to improve the efficiency of removal of the copper ions from residues for the utilization of residues from Chinese medicine. With the increase in activities of lignin-degrading enzymes, especially during the fermentation days 6 to 9, the removal rate of copper ions using M. officinalis residues increased dramatically. The rate of removal reached the maximum on the 14th day and was 3.15 times higher than the initial value. The rate of adsorption of copper ions on the fermentation-modified M. officinalis residues followed the pseudo-second-order kinetics. The adsorption isotherms were consistent with the Freundlich models. The adsorption enthalpy was positive, indicating that it was endothermic and elevation in temperature was favorable to this adsorption process. The adsorption free energy was negative, implying the spontaneity of the process. The copper ions adsorbed could be effectively recovered using 0.2 M hydrochloric acid solution. After five successive cycles of adsorption-regeneration, the fermentation-modified M. officinalis residues exhibited a stable adsorption capacity and greater reusability. The M. officinalis residues fermented with P. chrysosporium are low-cost and environmentally friendly copper ions adsorbent, and this preparation technique realizes the optimum utilization of Chinese medicine residues.

Preparation of bio-based magnetic adsorbent and application for efficient removal of Cd(II) from water

2018 ◽  
Vol 77 (5) ◽  
pp. 1313-1323 ◽  
Author(s):  
Jianjun Zhou ◽  
Xionghui Ji ◽  
Xiaohui Zhou ◽  
Jialin Ren ◽  
Yaochi Liu
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
Magnetic Adsorbent ◽  
Order Model ◽  
Efficient Removal ◽  
Adsorption Ability ◽  
Adsorption Sites ◽  
Pseudo Second Order

Abstract A novel magnetic bio-adsorbent (MCIA) was developed, characterized and tested for its Cd(II) removal from aqueous solution. MCIA could be easily separated from the solution after equilibrium adsorption due to its super-paramagnetic property. The functional and magnetic bio-material was an attractive adsorbent for the removal of Cd(II) from aqueous solution owing to the abundant adsorption sites, amino-group and oxygen-containing groups on the surface of Cyclosorus interruptus. The experimental results indicated that the MCIA exhibited excellent adsorption ability and the adsorption process was spontaneous and endothermic. The adsorption isotherm was consistent with the Langmuir model. The adsorption kinetic fitted the pseudo-second-order model very well. The maximum adsorption capacity of Cd(II) onto MCIA was 40.8, 49.4, 54.6 and 56.6 mg/g at 293, 303, 313 and 323 K, respectively. And the MCIA exhibited an excellent reusability and impressive regeneration. Therefore, MCIA could serve as a sustainable, efficient and low-cost magnetic adsorbent for Cd(II) removal from aqueous solution.

Preparation of Hydrated Calcium Silicate Gel and its Adsorption Properties for Cu(II)

2020 ◽  
Vol 993 ◽  
pp. 1445-1449
Author(s):  
Shi Jie Liu ◽  
Su Ping Cui ◽  
Hong Xia Guo ◽  
Ya Li Wang ◽  
Nan Li ◽  
...  
Keyword(s):  
Calcium Silicate ◽  
High Efficiency ◽  
Removal Rate ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Adsorption Method ◽  
Hydrated Calcium Silicate ◽  
Adsorption Performance ◽  
Optimum Reaction

Calcium silicate hydrate gel (CSH) was synthesized by calcium acetate and sodium silicate. The structure and morphology of CSH were characterized by X-ray diffraction analysis, Fourier transform infrared spectroscopy and Scanning electron microscopy. The adsorption performance of CSH was measured by static adsorption method. The results show that CSH has porous structure and large specific surface area, and the optimum reaction conditions is the reaction temperature of 25°C and calcium-silicon ratio of 1.2. It has the maximum adsorption capacity of more than 150 mg/g and the removal rate of more than 86% with Cu2+. And it shows the excellent adsorption performance, even when the concentration of Cu2+ is less than 200mg/L, the removal rate is above 90%. The research may provide a low-cost and high-efficiency adsorbent.

Removal of acetaminophen (ACT) from aqueous solution by using nanosilica adsorbent: experimental study, kinetic and isotherm modeling

2020 ◽  
Vol 49 (1) ◽  
pp. 55-62
Author(s):  
Akbar Eslami ◽  
Zahra Goodarzvand Chegini ◽  
Maryam Khashij ◽  
Mohammad Mehralian ◽  
Marjan Hashemi
Keyword(s):  
Removal Rate ◽  
Synthesis Method ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Content Type ◽  
Bet Analysis ◽  
Pseudo Second Order

Purpose A nanosilica adsorbent was prepared and characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and BET. Design/methodology/approach The optimum conditions for the highest adsorption performance were determined by kinetic modeling. The adsorbent was used for the adsorption of acetaminophen (ACT), and the parameters affecting the adsorption were discussed like pH, initial concentration, contact time and adsorbent dosage. The adsorbent have been characterized by SEM, XRD and BET analysis. The kinetic models including pseudo-first-order and pseudo-second-order with Langmuir and Freundlich isotherm models were applied to investigate the kinetic and isotherms parameters. Findings The adsorption of ACT increased to around 95% with the increase of nanosilica concentration to 30 g/L. Moreover, the adsorption process of ACT follows the pseudo-second-order kinetics and the Langmuir isotherm with the maximum adsorption capacity of 609 mg/g. Practical implications This study provided a simple and effective way to prepare of nanoadsorbents. This way was conductive to protect environmental and subsequent application for removal of emerging pollutants from aqueous solutions. Originality/value The novelty of the study is synthesizing the morphological and structural properties of nanosilica-based adsorbent (specific surface area, pore volume and size, shape and capability) and improving its removal rate through optimizing the synthesis method; and studying the capability of synthesis of nanosilica-based adsorbent for removal of ACT as a main emerging pharmaceutical water contaminant.

scholarly journals Development of low-cost iron mixed porous pellet adsorbent by mixture design approach and its application for arsenate and arsenite adsorption from water

2017 ◽  
Vol 36 (1-2) ◽  
pp. 372-392 ◽  
Author(s):  
Borano Te ◽  
Boonchai Wichitsathian ◽  
Chatpet Yossapol ◽  
Watcharapol Wonglertarak
Keyword(s):  
Low Cost ◽  
Mixture Design ◽  
Alkaline Condition ◽  
P Value ◽  
Maximum Adsorption Capacity ◽  
Natural Clay ◽  
Optimum Proportion ◽  
Negative Effect ◽  
Pseudo Second Order ◽  
Arsenite Removal

In this study, natural clay, iron oxide, and iron powder were combined to develop low-cost iron mixed porous pellet adsorbent for arsenate and arsenite removal from aqueous solution in batch experiments. The augmented simplex centroid mixture design was applied to obtain the optimum proportion of each constituent. Higher correlation coefficient of the models (R2 > 0.95), good distribution of residuals, and lower values of p value (<0.05) indicated that the method is suitable for determining the optimum mixture proportion. Extensive decrease of both arsenate and arsenite adsorption occurred in the alkaline condition (pH > 9). Kinetic and isotherm experimental data of both arsenate and arsenite were well described by the pseudo-second order and Sips models, respectively. The maximum adsorption capacity of arsenate and arsenite derived from Sips model were 13.33 and 19.06 mg/g, respectively. The separation and heterogeneity factors showed that both arsenate and arsenite were favorably adsorbed. Among coexisting anions, phosphate significantly showed negative effect on the adsorption of either arsenate or arsenite. The adsorbent could be effectively reused for several times after its regeneration and was considered as non-hazardous material after adsorption.

scholarly journals Simultaneous Adsorption of Cr(VI) and Phenol from Binary Mixture Using Iron Incorporated Rice Husk: Insight to Multicomponent Equilibrium Isotherm

2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Ankur Gupta ◽  
Chandrajit Balomajumder
Keyword(s):  
Experimental Data ◽  
Rice Husk ◽  
Low Cost ◽  
Binary Solution ◽  
Multicomponent System ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Adsorption Isotherm Models ◽  
Pseudo Second Order

Fe modified rice husk was prepared as a low cost biosorbent for the removal of Cr(VI) and phenol both singly and in combination from single and binary simulated synthetic waste water. Rice husk was modified by treating with FeSO4·7H2O. The results showed that impregnation of iron onto the surface of rice husk improved the adsorption capability of both Cr(VI) and phenol. The effects of process parameters for multicomponent system such as pH, adsorbent dose, and contact time onto the percentage removal of both Cr(VI) and phenol were investigated. The experimental data for the adsorption of both Cr(VI) and phenol onto the surface of Fe modified rice husk applied to various kinetic and adsorption isotherm models. Multicomponent isotherm models such as Nonmodified Langmuir, Modified Langmuir, Extended Langmuir, Extended Freundlich, Competitive Nonmodified Redlich Peterson, Competitive Modified Redlich Peterson were applied. The results show that Extended Freundlich model best described the experimental data for both Cr(VI) and phenol from binary solution. Pseudo second-order model agreed well with Cr(VI) while pseudo first-order model agreed well with phenol. Maximum adsorption capacity in synthetic binary solution of Cr(VI) and phenol was found to be 36.3817 mg g−1for Cr(VI) and 6.569 mg g−1for phenol, respectively.

scholarly journals Isotherm models and kinetics of copper adsorption by using hydrochar produced from hydrothermal carbonization of faecal sludge

2017 ◽  
Vol 7 (1) ◽  
pp. 102-110 ◽  
Author(s):  
Thammarat Koottatep ◽  
Krailak Fakkaew ◽  
Nutnicha Tajai ◽  
Chongrak Polprasert
Keyword(s):  
Functional Groups ◽  
Low Cost ◽  
Hydrothermal Carbonization ◽  
Pollutant Removal ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Surface Functional Groups ◽  
Water And Wastewater Treatment ◽  
Copper Adsorption ◽  
Faecal Sludge

Low cost adsorbents have been extensively reported for use as a promising substitution for commercial adsorbents for pollutant removal in water and wastewater treatment. In this study, hydrochar produced from the hydrothermal carbonization (HTC) of faecal sludge (FS) (called HTC-hydrochar) was further chemically modified with KOH (called KOH-hydrochar) to improve its surface functional groups, which were suitable for copper (Cu) removal. The adsorption of Cu was conducted using the produced HTC-hydrochar and KOH-hydrochar as absorbents. Experimental results showed the KOH-hydrochar could adsorb Cu at the maximum adsorption capacity of 18.6 mg-Cu/g-hydrochar with Cu removal efficiency of 93%, relatively higher than the HTC-hydrochar and a commercial powdered activated carbon. The quantity of the surface functional groups of the adsorbents was more effective in Cu removal than the surface area. The Cu adsorption mechanism was found to follow the pseudo-second order and intra-particle diffusion models and fit well with Freundlich and Langmuir isotherms. Application of hydrothermal carbonization could be a novel candidate to convert FS into hydrochar which is pathogen free, and to employ the produced hydrochar as an adsorbent to remove Cu from industrial wastewaters.

Equilibrium, kinetic and thermodynamic studies of mercury adsorption on almond shell

2012 ◽  
Vol 65 (8) ◽  
pp. 1341-1349 ◽  
Author(s):  
Shokooh Sadat Khaloo ◽  
Amir Hossein Matin ◽  
Sahar Sharifi ◽  
Masoumeh Fadaeinia ◽  
Narges Kazempour ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Low Cost ◽  
Second Order ◽  
Ion Concentration ◽  
Physical Parameters ◽  
Maximum Adsorption Capacity ◽  
Almond Shell ◽  
Pseudo Second Order ◽  
Uptake Process ◽  
Reaction Equations

The application of almond shell as a low cost natural adsorbent to remove Hg2+ from aqueous solution was investigated. Batch experiments were carried out to evaluate the adsorption capacity of the material. The chemical and physical parameters such as pH, sorbent amount, initial ion concentration, and contact time were optimized for the maximum uptake of mercury onto the solid surface. Adsorption isotherms were expressed by Langmuir and Freundlich adsorption models, and the experimental data were found to fit the Langmuir model rather than the Freundlich. The maximum adsorption capacity obtained from the Langmuir isotherm was 135.13 mg/g. A kinetic study was carried out with pseudo-first-order and pseudo-second-order reaction equations and it was found that the Hg2+ uptake process followed the pseudo-second-order rate expression. The thermodynamic values, ΔG0, ΔH0 and ΔS0, indicated that adsorption was an endothermic and spontaneous process. The potential of this material for mercury elimination was demonstrated by efficient Hg2+ removal from a synthetic effluent.

scholarly journals Treatment of effluent from fertilizer industry by adsorption on willow sawdust-removal of Ni(II) and Cd(II) from the effluent

2021 ◽  
pp. 1-12
Author(s):  
Raafia Najam ◽  
Syed Muzaffar Ali Andrabi
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
The World ◽  
Pseudo Second Order ◽  
Almost All ◽  
Willow Tree

Sawdust of willow has been investigated as an adsorbent for the removal of Ni(II), and Cd(II) ions from aqueous solution. Since willow tree is widely grown in almost all parts of Kashmir, it can be a common most easily available, sustainable, low cost adsorbent for the treatment of wastewaters in this part of the world where growing industrialization is affecting water quality like elsewhere in the world. Therefore, it is worthwhile to investigate the potential of sawdust of willow tree as an adsorbent for the removal of Ni(II) and Cd(II) ions from aqueous solution as a first step. Batch experiments were conducted to study the effect of some parameters such as contact time, initial concentration of metal ions, solution pH and temperature. Langmuir and Freundlich models were employed for the mechanistic analysis of experimental data obtained. Results reveal that in our system adsorption follows the Langmuir isotherm. The maximum adsorption capacity of Ni(II) and Cd(II) were found to be 7.98 and 7.11 mg/g respectively at optimum conditions. The pseudo-first-order and pseudo-second-order models were employed for kinetic analysis of adsorption process. The adsorption process follows pseudo-second-order kinetics. The efficacy of the adsorbent in the treatment of effluent from fertilizer factory has been investigated and the results have been found encouraging.

scholarly journals Highly Effective Covalently Crosslinked Composite Alginate Cryogels for Cationic Dye Removal

Gels ◽  
2021 ◽  
Vol 7 (4) ◽  
pp. 178
Author(s):  
Serap Sezen ◽  
Vijay Kumar Thakur ◽  
Mehmet Murat Ozmen
Keyword(s):  
Adsorption Capacity ◽  
Dye Removal ◽  
Low Cost ◽  
Dye Adsorption ◽  
Maximum Adsorption Capacity ◽  
High Porosity ◽  
Order Model ◽  
Removal Capacity ◽  
Pseudo Second Order ◽  
The One

Currently, macroporous hydrogels have been receiving attention in wastewater treatment due to their unique structures. As a natural polymer, alginate is used to remove cationic dyes due to its sustainable features such as abundance, low cost, processability, and being environmentally friendly. Herein, alginate/montmorillonite composite macroporous hydrogels (cryogels) with high porosity, mechanical elasticity, and high adsorption yield for methylene blue (MB) were generated by the one-step cryogelation technique. These cryogels were synthesized by adding montmorillonite into gel precursor, followed by chemical cross-linking employing carbodiimide chemistry in a frozen state. The as-prepared adsorbents were analyzed by FT-IR, SEM, gel fraction, swelling, uniaxial compression, and MB adsorption tests. The results indicated that alginate/montmorillonite cryogels exhibited high gelation yield (up to 80%), colossal water uptake capacity, elasticity, and effective dye adsorption capacity (93.7%). Maximum adsorption capacity against MB was 559.94 mg g−1 by linear regression of Langmuir model onto experimental data. The Pseudo-Second-Order model was fitted better onto kinetic data compared to the Pseudo-First-Order model. Improved porosity and mechanical elasticity yielding enhanced dye removal capacity make them highly potential alternative adsorbents compared to available alginate/montmorillonite materials for MB removal.

Sign in / Sign up

Export Citation Format

Share Document