scholarly journals Analysis of the Airflow Generated by Human Activity Using a Mobile Slipstream Measuring Device

Environments ◽  
2021 ◽  
Vol 8 (10) ◽  
pp. 97
Author(s):  
Min-kyeong Kim ◽  
Yongil Lee ◽  
Duckshin Park

Human activities, including walking, generate an airflow, commonly known as the slipstream, which can disperse contaminants indoors and transmit infection to other individuals. It is important to understand the characteristics of airflow to prevent the dissemination of contaminants such as viruses. A cylinder of diameter 500 mm, which is the average shoulder width of an adult male, was installed in a motorcar and moved at a velocity of 1.2 m/s, which is the walking speed of an adult male. The velocity profile of the slipstream generated during this movement was measured by locating the sensor support at 0.15–2.0 m behind the cylinder. The wind velocity was set to 1.2 m/s to conduct the numerical analysis. The measurement data revealed the velocity profile of the space behind the cylinder, and a comparison of the numerical analysis and the measurement results indicate very similar u (measured velocity) / U (moving velocity) results, with a maximum difference of 0.066, confirming that the measured values were correctly estimated from the results of the numerical analysis.

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1265 ◽  
Author(s):  
Johanna Geis-Schroer ◽  
Sebastian Hubschneider ◽  
Lukas Held ◽  
Frederik Gielnik ◽  
Michael Armbruster ◽  
...  

In this contribution, measurement data of phase, neutral, and ground currents from real low voltage (LV) feeders in Germany is presented and analyzed. The data obtained is used to review and evaluate common modeling approaches for LV systems. An alternative modeling approach for detailed cable and ground modeling, which allows for the consideration of typical German LV earthing conditions and asymmetrical cable design, is proposed. Further, analytical calculation methods for model parameters are described and compared to laboratory measurement results of real LV cables. The models are then evaluated in terms of parameter sensitivity and parameter relevance, focusing on the influence of conventionally performed simplifications, such as neglecting house junction cables, shunt admittances, or temperature dependencies. By comparing measurement data from a real LV feeder to simulation results, the proposed modeling approach is validated.


Geosciences ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 41
Author(s):  
Tim Jurisch ◽  
Stefan Cantré ◽  
Fokke Saathoff

A variety of studies recently proved the applicability of different dried, fine-grained dredged materials as replacement material for erosion-resistant sea dike covers. In Rostock, Germany, a large-scale field experiment was conducted, in which different dredged materials were tested with regard to installation technology, stability, turf development, infiltration, and erosion resistance. The infiltration experiments to study the development of a seepage line in the dike body showed unexpected measurement results. Due to the high complexity of the problem, standard geo-hydraulic models proved to be unable to analyze these results. Therefore, different methods of inverse infiltration modeling were applied, such as the parameter estimation tool (PEST) and the AMALGAM algorithm. In the paper, the two approaches are compared and discussed. A sensitivity analysis proved the presumption of a non-linear model behavior for the infiltration problem and the Eigenvalue ratio indicates that the dike infiltration is an ill-posed problem. Although this complicates the inverse modeling (e.g., termination in local minima), parameter sets close to an optimum were found with both the PEST and the AMALGAM algorithms. Together with the field measurement data, this information supports the rating of the effective material properties of the applied dredged materials used as dike cover material.


Sensors ◽  
2020 ◽  
Vol 20 (2) ◽  
pp. 560 ◽  
Author(s):  
Arkadiusz Kampczyk

In rail transport, measuring the actual condition of a circular curve of a railway track is a key element of track position monitoring not only during operation but also during final works. Predicting changes in its position in the horizontal plane is one of the most important related scientific issues. This paper presents the results of measurements performed with an innovative measuring device called the Magnetic-Measuring Square (MMS). The aim of the research was to demonstrate the acceptability of using the MMS. Horizontal versines of a rail track curve were measured as three neighboring points on a curve (using the method of lacing/stringlining, also called the three-point or the Hallade method), and the perpendicularity of rail joints and shortenings were measured. The MMS device presented in this article was used to measure versines and differences in rails lengths (rail shortenings in the curve) in the operating mode involving a laser distance meter with a laser beam (laser power P < 1 mW, laser wavelength λ = 635 nm) with a target cross, a camera, and a surveying measuring disk. The measurement results confirmed that it is possible to employ the MMS to monitor the geometry of railway track fragments such as track transition curves and railway track curves in rail transport.


2021 ◽  
Vol 23 (2) ◽  
pp. 57-63
Author(s):  
Marija Lazarevikj ◽  
◽  
Valentino Stojkovski ◽  
Viktor Iliev

In the technical practice, it is often necessary to measure or control the fluid flow rate in pipelines and channels. The velocity-area method requires a number of meters located at specified points in a suitable cross-section of closed conduits. Simultaneous measurements of local mean velocity with the meters are integrated over the gauging section to provide the discharge. In this paper, three approaches of this method are applied on a rectangular closed conduit to determine the air flow rate with integration techniques used to compute the discharge assume velocity distributions that closely approximate known laws, especially in the neighborhood of solid boundaries. For this purpose, meters for velocity were 7 Pitot tubes placed vertically in predefined measurement points covering the conduit height, and moved horizontally along the conduit width. The position of the Pitot tubes along the conduit width was monitored and controlled by a linear displacement transducer. Pressure is measured using digital sensors. The first technique for determination of air flow rate is on basis of fixed (stopping) measuring points across the conduit width as averaged values of local velocity, the second one is semi continual measurement of velocity profile by applying interpolation between the average local velocity on fixed (stopping) points and measured velocity in the movement between two positions, and the third is by continuously moving the Pitot tubes without stopping. The results of the three techniques are calculated and presented using different types of software. Considering the last technique, comparison of results is made applying different movement speeds of the Pitot tubes in order to examine their influence on the velocity profile.


2017 ◽  
Vol 6 (2) ◽  
pp. 279-284 ◽  
Author(s):  
László Hegymegi ◽  
János Szöllősy ◽  
Csaba Hegymegi ◽  
Ádám Domján

Abstract. Geomagnetic observatories use classical theodolites equipped with single-axis flux-gate magnetometers known as declination–inclination magnetometers (DIM) to determine absolute values of declination and inclination angles. This instrument and the measurement method are very reliable but need a lot of handwork and experience. The authors developed and built a non-magnetic theodolite which gives all measurement data in digital form. Use of this instrument significantly decreases the possibility of observation errors and minimises handwork. The new instrument is presented in this paper together with first measurement results in comparison to the classical DIM.


2018 ◽  
Vol 11 (9) ◽  
pp. 5363-5388 ◽  
Author(s):  
Akihiro Uchiyama ◽  
Tsuneo Matsunaga ◽  
Akihiro Yamazaki

Abstract. Ground-based networks have been developed to determine the spatiotemporal distribution of the optical properties of aerosols using radiometers. In this study, the precision of the calibration constant (V0) for the sky radiometer (POM-02) that is used by SKYNET was investigated. The temperature dependence of the sensor output was also investigated, and the dependence in the 340, 380, and 2200 nm channels was found to be larger than for other channels and varied with the instrument. In the summer, the sensor output had to be corrected by a factor of 1.5 % to 2 % in the 340 and 380 nm channels and by 4 % in the 2200 nm channel in the measurements at Tsukuba (36.05∘ N, 140.13∘ E), with a monthly mean temperature range of 2.7 to 25.5 ∘C. In the other channels, the correction factors were less than 0.5 %. The coefficient of variation (CV, standard deviation/mean) of V0 from the normal Langley method, based on the data measured at the NOAA Mauna Loa Observatory, is between 0.2 % and 1.3 %, except in the 940 nm channel. The effect of gas absorption was less than 1 % in the 1225, 1627, and 2200 nm channels. The degradation of V0 for wavelengths shorter than 400 nm (−10 % to −4 % per year) was larger than that for wavelengths longer than 500 nm (−1 to nearly 0 % per year). The CV of V0 transferred from the reference POM-02 was 0.1 % to 0.5 %. Here, the data were simultaneously taken at 1 min intervals on a fine day, and data when the air mass was less than 2.5 were compared. The V0 determined by the improved Langley (IML) method had a seasonal variation of 1 % to 3 %. The root mean square error (RMSE) from the IML method was about 0.6 % to 2.5 %, and in some cases the maximum difference reached 5 %. The trend in V0 after removing the seasonal variation was almost the same as for the normal Langley method. Furthermore, the calibration constants determined by the IML method had much higher noise than those transferred from the reference. The modified Langley method was used to calibrate the 940 nm channel with on-site measurement data. The V0 obtained with the modified Langley method compared to the Langley method was 1 % more accurate on stable and fine days. The general method was also used to calibrate the shortwave-infrared channels (1225, 1627, and 2200 nm) with on-site measurement data; the V0 obtained with the general method differed from that obtained with the Langley method of V0 by 0.8 %, 0.4 %, and 0.1 % in December 2015, respectively.


Author(s):  
Mochamad Zaeynuri Setiawan ◽  
Fachrudin Hunaini ◽  
Mohamad Mukhsim

The phenomenon that often arises in a substation is the problem of partial discharge in outgoing cable insulation. Partial discharge is a jump of positive and negative ions that are not supposed to meet so that it can cause a spark jump. If a partial discharge is left too long it can cause insulation failure, the sound of snakes like hissing and the most can cause a flashover on the outgoing cable. Then a partial discharge detection prototype was made in the cable insulation in order to anticipate the isolation interference in the outgoing cable. Can simplify the work of substation operators to check the reliability of insulation on the outgoing side of each cubicle. So it was compiled as a method for measuring sound waves caused by partial discharge in the process of measuring using a microphone sensor, the Arduino Mega 2560 module as a microcontroller, the LCD TFT as a monitoring and the MicroSD card module as its storage. The microphone sensor is a sensor that has a high sensitivity to sound, has 2 analog and digital readings, and is easily designed with a microcontroller. Basically the unit of measure measured at partial discharge is Decibels. The results of the prototype can be applied to the cubicle and the way it works is to match the prototype to the outgoing cubicle cable then measure from the cable boots connector to the bottom of the outgoing cable with a distance of 1 meter. Then the measurement results will be monitored on the TFT LCD screen in the form of measurement results, graphs and categories on partial discharge. In this design the measurement data made by the microphone can be stored with microSD so that it can make an evaluation of partial discharge handling in outgoing cable insulation.


Author(s):  
Dodi Sofyan Arief ◽  
◽  
Eko Jadmiko ◽  
Adhy Prayitno ◽  
Muftil Badri ◽  
...  

Dial indicator is a comparison device usually used in industrial activities, especially in production. To make measurements at this time must be supported by technology that can facilitate operators when using it and when analyzing measurement results. Involving the programme and microcontroller are a solution to developing in roundness measurement, and then the results can be more accurate or thorough between the readable values read from the measuring instrument with the actual value of varying the amount of data. Roundness application is a program that can input measurement data automatically and can do calculations directly. Then, it can display a reference circle, a table that calculates the values of X, Y, R, X’, Y’, R’, Roundness Deviation, Run out Concentricity or a shift in the center point and also the center point shift or Theta. In measuring roundness, the test object is used the Standard Mandrel which has been certified by PT. Global Quality Indonesia, by determining three points or positions, namely in the first position the amount of data is 180, in the second position the amount of data is 90 and in the third position, the amount of data is 60 with a rotating speed of 15 mm/s. The results of the reference circle can be seen in each calculation in each position, in the second position the roundness deviation values are approaching of the Mandrel.


ACTA IMEKO ◽  
2015 ◽  
Vol 4 (2) ◽  
pp. 39 ◽  
Author(s):  
Leonard Klaus ◽  
Barbora Arendacká ◽  
Michael Kobusch ◽  
Thomas Bruns

For the dynamic calibration of torque transducers, a model of the transducer and an extended model of the mounted transducer including the measuring device have been developed. The dynamic behaviour of a torque transducer under test is going to be described by its model parameters. This paper describes the models with these known and unknown parameters and how the calibration measurements are going to be carried out. The principle for the identification of the transducer's model parameters from measurement data is described using a least squares approach. The influence of a variation of the transducer's parameters on the frequency response of the expanded model is analysed.


2017 ◽  
Vol 29 (2_suppl) ◽  
pp. 110S-119S ◽  
Author(s):  
Makoto Miyazaki

Measurement of individual radiation dose is crucial for planning protective measures after nuclear accidents. The purpose of this article is to explain the various initiatives taken after the TEPCO Fukushima Daiichi Nuclear Power Plant accident, including the D-shuttle project wherein residents from affected areas wore a personal dosimeter to measure their own external exposure. The experience in Fukushima revealed several issues such as gaining residents’ trust and ensuring appropriate communication of the measured data. The D-shuttle project also revealed that obtaining individual dose measurement data had 2 purposes, as the information obtained was to be utilized by the residents for self-protection and by the authorities for deriving the dose distribution of the population to aid in designing large-scale protection measures. The lessons learned are that both the residents and the authorities need to understand and share the meaning of individual dose measurements and the measurement results must be used with due respect for the residents’ privacy and other concerns.


Sign in / Sign up

Export Citation Format

Share Document